Simple generation of high-power,picosecond, tunable excimer laser pulses

A single excimer laser (a modified commercial oscillation-amplifier combination) is used to pump a dye laser generating a single ps pulse at twice the excimer wavelength and to amplify the frequency-doubled pulse to high peak powers. With XeCl at 308 nm an output pulse energy of 10 mJ with <5 ps pulse width was achieved with <5% ASE energy.     

30-mJ, diode-pumped, chirped-pulse Yb:YLF regenerative amplifier

A diode-pumped chirped-pulse regenerative amplifier with a cooled Yb:YLF crystal has been developed. The output pulse energy is 30 mJ at 20-Hz repetition rate. A high effective extraction efficiency of 68% is obtained, which is attributed to reduced saturation fluence at low temperature and to a high effective pulse energy fluence during regenerative amplification. After pulse compression by use of a parallel grating pair, 18-mJ pulse energy and 795-fs pulse duration are obtained.     

Laser performance of monolithic Cr,Nd:YAG self-Q-switched laser

The self-Q-switched laser performance of monolithic Cr⁴⁺,Nd³⁺:YAG concave-planar resonator with 5-mm length was studied experimentally and theoretically. The slope efficiency is as high as 24% and pump threshold is as low as 64 mW. The pulse width, the single pulse energy and the pulse repetition rate of monolithic Cr,Nd:YAG self-Q-switched laser were measured as a function of absorbed pump power. With the increase of pump power, the pulse width decreases and the pulse energy and the pulse repetition rate increase. The average output power of 91 mW with pulse width of 7 ns at repletion rate of 35.5 kHz was obtained at the maximum absorbed pump power of 440 mW, the peak power is as high as 370 W. The theoretical prediction of pulse energy, pulse width and pulse repetition rate as a function of absorbed pump power based on rate equations is in a good agreement with our experimental data. This can lead to develop the diode laser-pumped monolithic self-Q-switched solid-state microchip lasers.     

Single-frequency, Q-switched Ho:YAG laser at room temperature injection-seeded by two F-P etalons-restricted Tm, Ho:YAG laser

We demonstrated a 1.91 μm pumped, injection-seeded Q-switched Ho:YAG laser operating at room temperature. By inserting two Fabry-Perot etalons into the laser cavity, single-frequency Tm, Ho:YAG seed lasing was achieved at a wavelength of 2090.9 nm, with a typical output power of 60 mW. Single-frequency, nearly transform-limited Q-switched operation of the Ho:YAG laser was achieved by injection seeding. The output energy of the single-frequency Q-switched pulse is 7.6 mJ, with a pulse width of 132 ns and a repetition rate of 100 Hz. We measured the pulse spectrum, half-width of which was 3.5 MHz, by a heterodyne technique.     

Nd,Cr:YAG自调Q自锁模激光器的研究

实验采用光纤耦合激光二极管泵浦,得到了二极管泵浦Nd,CrYAG自调Q自锁模1.064 μm激光输出,其锁模调制深度达到了近100%,其输出功率最高可达1.9 W,平均输出功率稳定性优于1%.实验表明平均输出功率、重复频率和脉冲宽度随泵浦功率增加而上升.     

Efficient, kHz repetition rate, gain-switched Cr:forsterite laser

We have developed a gain-switched room-temperature Cr:forsterite laser operating at repetition rates of between 1 and 34 kHz, and pumped by a continuous wave, Q-switched Nd:YAG laser. With optimised output coupling, an output pulse energy of 52 μJ was measured at 1.5 kHz repetition rate, corresponding to 11% efficiency and 13% slope efficiency. Threshold pulse energy was 53 μJ. Output power of 370 mW was obtained at 10 kHz repetition rate and 4.4 W pump power. Water cooling was not required for repetition rates up to 10 kHz. In a tunable, folded resonator, the Cr:forsterite wavelength tuned between 1173 and 1338 nm. This laser operated with maximum pulse energy of 34 μJ, efficiency of 13%, and power of 307 mW. The laser output was close to diffraction-limited with M² of 1.2. Received: 6 January 1999 / Published online: 29 July 1999     

Conductively-cooled,high-energy,single-frequency diode pumped slab laser for space applications

A laser-diode-pumped high efficiency, high pulse energy and single-frequency oscillator and amplifier for potential space environment applications have been developed and demonstrated using conductively-cooled heat removal. A diode-pumped injection seeded single-frequency oscillator was achieved by using the resonance-detection technique in Q-Switching operation, and Nd: YAG zigzag slabs based on “pump on bounce” are used in power amplifier stage for high-efficiency pulse energy extraction. Output pulse energy of 800 mJ with 11 ns pulse duration is obtained at a repetition rate of 100 Hz, with a near 3× diffraction-limit beam and an optical-to-optical efficiency of 18%. The experimental result shows that the laser has compact structure, high efficiency, reliability, conductive cooling and can be used for space environments.     

High repetition rate,high peak power acousto-optical Q-switched 946 nm Nd:YAG laser

A diode-end-pumped high repetition rate, high peak power acousto-optical (AO) Q-switched 946 nm Nd:YAG laser was demonstrated in this paper. In our experiments, a 20 mm miniature acousto-optical Q-switch was employed in a 45 mm linear laser cavity for generating the short laser pulse. At a repetition rate of 10 kHz, a maximum average output power of 2.9 W was achieved with a pulse width of 24.4 ns, giving a peak power of 11.9 kW. To the best of our knowledge, this is the highest peak power 946 nm Nd:YAG laser at high repetition rate operation. Moreover, pulse train with good stability was also obtained at the repetition rate of 50 kHz. At an incident pump power of 22.3 W, up to an average output power of 3.5 W pulsed 946 nm laser was generated at 50 kHz with a pulse width of 69 ns, corresponding to an optical conversion efficiency of 15.7% and an average slope efficiency of 24.1%, respectively.     

High-beam-quality, 5.1 J, 108 Hz diode-pumped Nd:YAG rod oscillator-amplifier laser system

A high efficiency, high beam quality diode-pumped Nd:YAG master oscillator power-amplifier (MOPA) laser with six amplifier stages is demonstrated. The oscillator with two-rod birefringence compensation was designed as a thermally determined near hemispherical resonator, which presents a pulse energy of 223 mJ with a beam quality value of M² = 1.29 at a repetition rate of 108 Hz. The MOPA system delivers a pulse energy of 5.1 J with a pulse width of 230 μs, a M² factor of 3.6 and an optical-to-optical efficiency of 38.5%. To the best of our knowledge, this is the highest pulse energy for a diode-pumped Nd:YAG rod laser operation with a high beam quality and a pulse width of hundreds of microseconds at a repetition rate of over 100 Hz.     

Generation, measurement and optimization of a variable duration, short pulse, mode-locked cavity-dumped Nd:YAG laser

Spectral and temporal measurements undertaken on a single picosecond laser pulse from a flash lamp pumped, cavity dumped, active/passive mode-locked Nd:YAG laser are presented in this paper. Optimization of several parameters of the resonator cavity produced a single pulse with 0.7 mJ energy and 10² contrast. The pulse duration was variable from 24 to 120 ps by using intra-cavity etalons of different thicknesses. The pulse width and spectrum of the pulse were simultaneously measured using a second harmonic autocorrelator and a spectrometer. The time bandwidth product was 0.445, which is close to theoretical limit for a bandwidth limited pulse.     

Tunable,sub-nanosecond KrF-Raman laser in the ultraviolet

A 0.5 cm^–1 bandwidth injection-locked KrF laser pumps a rare-gas Brillouin cell to produce a reflected pulse with a leading edge risetime of 1 ns, tunable from 248.1 to 248.7 nm. Consistent with Lamb theory of laser amplifiers, subsequent excimer amplification of this pulse produces an intense 500 ps spike on the pulse leading edge. Stimulated Raman scattering then separates the spike from the parent pulse, yielding a tunable short pulse at the first Stokes (S ₁) wavelength. Varying the Raman cell length results in a variable Raman threshold and an adjustable short pulse duration: 250 ps pulses at energies of 3–4 mJ at 268 nm with a 50 cm methane cell and 350 ps, 5 mJ pulses from a 100 cm cell are measured with a streak camera. First pass Raman conversion of the spike toS ₁ followed by second pass backward Raman amplification, where the parent 248 nm pulse serves as the pump beam for the reflectedS ₁ pulse, yields simultaneousS ₁ pulses of 20–25 mJ in the 800 ps range andS ₂ pulses of 550 ps at 5–6 mJ near 290 nm. This laser will avoid collision effects during laser excitation and enable quantitative, single pulse imaging of OH radicals in turbulent combustion because of its high pulse energy.     

Sounds, source levels, and associated behavior of humpback whales, southeast Alaska

Humpback whales in Southeast Alaskan waters produced five categories of sounds: moans, grunts, pulse trains, blowhole-associated sounds, and surface impacts. Frequencies (Hz) of moans and grunts were 20-1900. Major energy in low-frequency pulse trains was in a band of 25-80 Hz with pulse duration of 300-400 ms. Blowhole-associated sounds, recorded as transiting whales encountered one another, were of two types: shrieks, 555-2000 Hz, and trumpetlike horn blasts with fundamental at 414 Hz (median). Pulses and spread spectrum noise were associated with gas bubble formation and explosive bursts, respectively, in connection with spiral feeding maneuvers. Surface impacts resulted from fluke or flipper slaps in sequences of 3-21 sounds. Source levels ranged from 162 (low-frequency pulse trains) to 192 dB (surface impacts), re: 1 microPa, 1 m. Songs, commonly heard on winter breeding grounds, were absent from our recordings. Feeding and perhaps certain other whale activities can be monitored based on sound production.     

MR imaging and cervical fixation devices: Evaluation of ferromagnetism,heating, and artifacts at 1.5 tesla

The purpose of this study was to assess ferromagnetism, heating, and artifacts for cervical fixation devices exposed to a 1.5 T MR system. Cervical fixation devices (three halos, one tong and two halo vests) were evaluated for compatibility with MR procedures. Ferromagnetism was determined using a previously described technique. Heating was evaluated by measuring temperatures at various positions on the cervical fixation devices while applied to a volunteer subject before and during the use of various pulse sequences, including an magnetization transfer contrast (MTC) sequence. Artifacts associated with routine clinical MR imaging of the cervical spine were qualitatively evaluated with the cervical fixation devices applied to a volunteer subject. None of the devices displayed attraction to the magnetic field. The temperature changes were ±1.5°C in each instance. The MTC pulse sequence produced a sensation of “heating” the skull pins that may have been caused by vibration of the cervical fixation device. The MR images of the cervical spine were obtained without apparent artifacts using each routine, clinical pulse sequence. The lack of ferromagnetism, negligible heating, and capability of obtaining diagnostically acceptable studies of the cervical spine indicate that MR imaging performed at 1.5 T or less may be conducted safely in patients with each of the cervical fixation devices tested using conventional pulse sequences.     

温度回路-小孔脉管制冷中的新现象

一台可工作在双向进气模式和小孔模式下的单级脉管制冷机,当双向进气方式采用并联双阀双向进气时,最低制冷温度为19.3K,50K以下的制冷量变化约为2W/K;当双向进气阀门关闭时,制冷机就工作在小孔模式下,最近的研究工作发现,当制冷机工作在小孔模式下时出现了一个新的现象-脉管冷端温度存在温度回路,该特点与脉管冷端的热负荷及小孔开度的调节方法有关,该现象的发现对于理解双向进气模式下温度不稳定问题提供了一个新的思路。     

High Power, Frequency Tunable, Submillimeter Wave ESR Device Using a Gyrotron as a Radiation Source

ESR device using a submillimeter wave gyrotron as a radiation source and a pulse magnet for high field up to 30 T has been constructed. Our gyrotrons (Gyrotron FU series) were developed as millimeter and submillimeter wave radiation sources and have attractive advantages for ESR spectroscopy, for example, high power and frequency tunability over broad range. The ESR device has been successfully applied to three cases of ESR measurements. In the first case, the temperature dependence of ESR was measured for a typical antiferromagnetic material MnO at the frequency of 301 GHz. In the second case, the dependence of the fine structure constant of the ruby on the magnetic field intensity was measured in the millimeter to submillimeter wave region. In these two cases, the gyrotron was operated by complete cw mode. In the final case, a pulse technique was applied to the ESR, the gyrotron was operated in pulse mode and the pulsed magnetic field was generated in the synchronized phase with the gyrotron operation.     

10 GHz, 2.4 ps pulse generation using a single-stage dual-drive Mach-Zehnder modulator

This Letter reports on picosecond pulse generation at a repetition of 10 GHz by using a single-stage electro-optic LiNbO(3) Mach-Zehnder modulator, stressing the simplicity of its setup. It is analytically and experimentally proved that dual-arm modulation with in-phase sinusoidal signals having slightly different amplitudes generated a highly coherent optical comb with a great spectral flatness and a parabolic phase relationship in its spectrum. The generated comb was Fourier synthesized and shaped into an ultrashort pulse train with an optical bandpass filter and a dispersive fiber. The pulse source was highly stable, exhibiting an ultralow timing jitter of less than 130 fs.     

High power and efficiency of a 2044-nm c-cut Tm, Ho:YAlO3 laser

A high power and efficiency of c-cut Tm, Ho:YAlO₃ (YAP) laser is reported in the paper. The laser operated in continuous wave (CW) mode or Acousto-optical (AO) Q-switched mode at 2044 nm. The Tm, Ho:YAP crystal was cooled at the temperature of 77 K and pumped by a fiber-coupled laser diode (LD) with the centre output wavelength of 794.8 nm. In CW operation, a 9.30-W output power was obtained at a 150-mm physical cavity length, corresponding to a slope efficiency of 42.5%. In Q-switch mode, the output average power of 9 W was achieved at the pulse repetition frequency (PRF) of 10 kHz with a 130-ns pulse width. Moreover, the energy per pulse of 3.54 mJ in 47 ns was acquired at 2.5 kHz with a 75.3-kW peak power.     

High-energy, diode-pumped, picosecond Yb:YAG chirped-pulse regenerative amplifier for pumping optical parametric chirped-pulse amplification

A diode-pumped, cryogenic-cooled Yb:YAG regenerative amplifier utilizing gain-narrowing has been developed. A 1.2-ns chirped-seed pulse was simultaneously amplified and compressed in the regenerative amplifier, which generated a 35-ps pulse with ~8-mJ of energy without a pulse compressor. Second-harmonics of the amplified pulse was used to pump picosecond two-color optical parametric amplification.     

High-energy, high-power ytterbium-doped Q-switched fiber laser

We report on a Q -switched, cladding-pumped, ytterbium-doped large-mode-area fiber laser operating at 1090 nm that is capable of generating 2.3 mJ of output pulse energy at a 500-Hz repetition rate and more than 5 W of average output power at higher repetition rates in a high-brightness beam (M(2) = 3) . Using a similar fiber with a smaller core, we generated >0.5-mJ pulses in a diffraction-limited beam. Our results represent a threefold increase in pulse energy over previously published values for Q-switched fiber lasers and firmly establish fiber lasers as compact, multiwatt, multimillijoule pulse sources with large scope for both industrial and scientific applications.     

外腔式宽调谐被动调QNd:YVO_4/PPMgLN光学参量振荡器

报道了一个低阈值宽调谐、被动调Q、单谐振掺MgO的周期性极化铌酸锂晶体(PPMgLN)光学参量振荡器。利用被动调Q的Nd:YVO4激光器作为泵浦源,采用外腔结构,在室温下,实现了PPMgLN晶体的准相位匹配光学参量振荡。光参量振荡的阈值仅为0.27W(单脉冲能量4.5μJ、脉宽35ns);在泵浦光为1.35W(脉冲能量8.2μJ、脉宽35ns),PPMgLN周期为31μm时,获得了161.9mW,3.202μm脉冲激光输出;同时获得了98.5mW的1.594μm信号光输出,总的光光转化效率达到19.3%。通过改变晶体的周期,实现了闲频光3.13～4.19μm,信号光1.43～1.65μm的宽带可调谐激光输出。