Application of photocatalytic technology for NO<Subscript>x</Subscript> removal

Materials that contain a photocatalyst have a semi-permanent capacity for removing harmful gases from the ambient air. It is the purpose of this study to investigate the photocatalytic activity of commercial paints containing TiO₂ nanoparticles towards NO and NO₂. Experiments were carried out in a stainless steel (30 m^-3) walk-in type environmental chamber (Indoortron), under “real world setting” conditions of temperature, relative humidity, irradiation and pollutant concentrations. Two types of nanoparticle TiO₂-containing paints were tested for their depolluting properties: a mineral silicate paint and a water-based styrene acrylic paint. The results showed a significant effect of TiO₂-materials in reducing NO_x. It was found that up to 74% of NO and 27% of NO₂ were photo-catalytically degraded by the mineral silicate paint, while degradation percentage using the styrene acrylic paint reached 91% and 71% for NO and NO₂, respectively. The photo-catalytic rate of NO on the mineral and styrene acrylic paint was calculated to 0.11 μg m^-2 s and 0.18 μg m^-2 s, respectively, indicating higher photocatalytic performance of the organic based material. The effect of relative humidity (RH) was also investigated. An increase of RH from 20% to 50% inhibited the NO_x photocatalysis on the surface of the samples. PACS 81.16.Hc; 81.65.Mq; 82.33.Tb; 82.50.Hp; 82.65.+r     

Spectroscopic Properties and Energy Transfer Analysis of Tm<Superscript>3+</Superscript>-Doped BaF<Subscript>2</Subscript>-Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>-GeO<Subscript>2</Subscript>-La<Subscript>2</Subscript>O<Subscript>3</Subscript> Glass

This paper reports on the spectroscopic properties and energy transfer analysis of Tm³⁺-doped BaF₂-Ga₂O₃-GeO₂-La₂O₃ glasses with different Tm₂O₃ doping concentrations (0.2, 0.5, 2.0, 2.5, 3.0, 3.5, 3.5, 4.0 wt%). Mid-IR fluorescence intensities in the range of 1,300 nm−2,200 nm have been measured when excited under an 808 nm LD for all the samples with the same pump power. Energy level structure and Judd-Ofelt parameters have been calculated based on the absorption spectra of Tm³⁺, cross-relaxation rates and multi-phonon relaxation rates have been estimated with different Tm₂O₃ doping concentrations. The maximum fluorescence intensity at around 1.8 μm has been obtained in Tm₂O₃-3 wt% sample and the maximum value of calculated stimulated emission cross-section of Tm³⁺ in this sample is about 0.48 × 10⁻²⁰ cm² at 1,793 nm, and there is not any crystallization peak in the DSC curve of this sample, which indicate the potential utility of Tm³⁺-doped BaF₂-Ga₂O₃-GeO₂- La₂O₃ glass for 2.0-μm optical fiber laser.     

Quenching effects on pulsed photoacoustic signals in NO2–air samples

A theoretical expression for the pulsed photoacoustic signal amplitude from NO₂–air mixtures is deduced based on a two-level system and the inhomogeneous wave equation, in the limit where the V-T relaxation time is longer than the laser pulse width (low buffer pressure). In this time limit, the photoacoustic signal from NO₂, at constant pressure, after excitation by pulses from a Nd:YAG laser at 532 nm, is measured at different buffer pressures. The relaxation rates are obtained by measuring the quenching of visible fluorescence induced by the same laser. The experimental dependence of the photoacoustic signal amplitude on air pressure shows a very good agreement with the model, where the measured relaxation rates are included.     

Effects of dopant on the electrochemical properties of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode materials

The effects of dopant on the electrochemical properties of spinel-type Li_3.97M_0.1Ti_4.94O₁₂ (M = Mn, Ni, Co) and Li_(4-x/3)Cr_xTi_(5-2x/3)O₁₂(x = 0.1, 0.3, 0.6, 0.9, 1.5) were systematically investigated. Charge-discharge cycling were performed at a constant current density of 0.5 mA/cm² between the cut-off voltages of 3.0 and 1.0 V, the experimental results showed that Cr³⁺ dopant improved the reversible capacity and cycling stability over the pristine Li₄Ti₅O₁₂. The substitution of the Mn³⁺ and Ni³⁺ slightly decreased the capacity of the Li₄Ti₅O₁₂. Dopants such as Co³⁺ to some extent worsened the electrochemical performance of the Li₄Ti₅O₁₂.     

Nanocrystalline CaCu<Subscript>3</Subscript>Ti<Subscript>4</Subscript>O<Subscript>12</Subscript> powders prepared by egg white solution route: synthesis,characterization and its giant dielectric properties

Nanocrystalline CaCu₃Ti₄O₁₂ powders with particle sizes of 50–90 nm were synthesized by a simple method using Ca(NO₃)₂·4H₂O, Cu(NO₃)₂·4H₂O, titanium(diisoproproxide) bis(2,4-pentanedionate) and freshly extracted egg white (ovalbumin) in aqueous medium. The synthesized precursor was characterized by TG-DTA to determine the thermal decomposition and crystallization temperature which was found to be at above 400 °C. The precursor was calcined at 700 and 800 °C in air for 8 h to obtain nanocrystalline powders of CaCu₃Ti₄O₁₂. The calcined CaCu₃Ti₄O₁₂ powders were characterized by XRD, FTIR, SEM and TEM. Sintering of the powders was conducted in air at 1100 °C for 16 h. The XRD results indicated that all sintered samples have a typical perovskite CaCu₃Ti₄O₁₂ structure and a small amount of CuO, although the sintered sample of the 700 °C calcined powders contained some amount of CaTiO₃. SEM micrographs showed the average grain sizes of 12.0±7.8 and 15.5±8.9 μm for the sintered CaCu₃Ti₄O₁₂ ceramics prepared using the CaCu₃Ti₄O₁₂ powders calcined at 700 and 800 °C, respectively. The sintered samples exhibit a giant dielectric constant, ε^′ of ∼ 1.5–5×10⁴. The dielectric behavior of both samples exhibits Debye-like relaxation, and can be explained based on a Maxwell–Wagner model. PACS 77.22.Gm; 81.05.Je; 81.07.Wx; 81.20.Ev     

Fast ionic conduction in cubic hafnium garnet Li<Subscript>7</Subscript>La<Subscript>3</Subscript>Hf<Subscript>2</Subscript>O<Subscript>12</Subscript>

A new member of the family of garnets with fast lithium ion conduction has been found with the composition Li₇La₃Hf₂O₁₂. The anion arrangement corresponds to the oxygen framework in garnets, e.g., in Ca₃Fe₂Si₃O₁₂. Hafnium is coordinated octahedrally while the lanthanum environment can be described as a distorted cube. Lithium occupies a large number of positions with tetrahedral, trigonal planar, and metaprismatic coordination. Li₇La₃Hf₂O₁₂ shows a lithium bulk ion conductivity of 2.4 × 10⁻⁴ Ω⁻¹ cm⁻¹ at room temperature with an activation energy of 0.29 eV.     

Photopyroelectric spectroscopy of Sb<Subscript>2</Subscript>O<Subscript>3</Subscript> - ZnO ceramics

Photopyroelectric spectroscopy is used to study the band-gap energy of the ceramic (ZnO + xSb₂O₃), x = 0.1 - 1.5 mol% and the ceramic (ZnO + 0.4 mol%  Bi₂O₃ + xSb₂O₃), x = 0 - 1.5 mol% sintered at isothermal temperature, 1280 °C, for 1 and 2 hours. The wavelength of incident light, modulated at 9 Hz, is kept in the visible range and the photopyroelectric spectrum with reference to doping level is discussed. The band-gap energy is reduced from 3.2 eV, for pure ZnO, to 2.86, 2.83 eV for the samples without Bi₂O₃at 0.1 mol% of Sb₂O₃ for 1 and 2 hours of sintering time, respectively. It is reduced to 2.83, 2.80 eV for the samples with Bi₂O₃ at 0 mol% of Sb₂O₃ for 1 and 2 hours of sintering time, respectively. The steepness factor σ_A which characterizes the slop of exponential optical absorption is discussed with reference to the doping level. The phase constitution is determined by XRD analysis; microstructure and compositional analysis of the selected areas are analyzed using SEM and EDX.     

Resonance photoacoustic spectroscopy and gas analysis of gaseous flow at reduced pressure

The results of theoretical and experimental studies of sensitivity of a resonant photoacoustic Helmholtz resonator detector for gas flowing through a photoacoustic cell under reduced pressure are presented. The measurements of the sensitivity and ultimate sensitivity of the differential photoacoustic cell were performed with a near-IR room-temperature diode laser using the well-known H₂O absorption line (12496.1056 cm^-1) as a reference. The measured value of the sensitivity (6–17 Pa W m^-1) is in satisfactory agreement with the calculated one, which equals 6–35 Pa W m^-1. The obtained value of the ultimate sensitivity ((3–5)×10^-7 W m^-1 Hz^-1/2) provides measurements of the concentration of molecules at the ppb–ppm level. Received: 19 April 2001 / Revised version: 18 September 2001 / Published online: 7 November 2001     

Silver Nanoparticle-Enhanced Chemiluminescence Method for Determining Naproxen Based on Europium(III)-Sensitized Ce(IV)-Na<Subscript>2</Subscript>S<Subscript>2</Subscript>O<Subscript>4</Subscript> Reaction

A simple and sensitive chemiluminescence (CL) method coupled with flow-injection technique is proposed to determine naproxen (NAP). The method is based upon the enhancement of the weak CL signal arising from the reaction of Ce(IV) and Na₂S₂O₄ with Eu³⁺ to form the Eu³⁺-Ce(IV)-Na₂S₂O₄ system. The CL intensity was significantly increased by the introduction of NAP into this system in the presence of silver nanoparticles (Ag NPs). Examination of the recorded UV–vis spectra and fluorescence spectra indicated that the energy of the intermediate SO₂*, which originated from the redox reaction of Ce(IV) and Na₂S₂O₄, was transferred to Eu³⁺ via NAP and that the process was accelerated by Ag NPs due to their catalytic activity. Under the optimum conditions, the CL intensity was increased with increasing NAP concentration and the correlation was linear (r = 0.9992) over the NAP concentration range of 1–420 ng mL⁻¹. The limit of detection (LOD) was 0.11 ng mL⁻¹ with a relative standard deviation (RSD) of 1.15% for 5 replicate determinations of 200 ng mL⁻¹ NAP. The method was successfully applied to determine NAP in pharmaceutical and biological samples.     

Spectroscopic properties of Er<Superscript>3+</Superscript> ions in LiNbO<Subscript>3</Subscript> crystals codoped with HfO<Subscript>2</Subscript>

The results of the spectroscopic analysis of transition strengths for Er³⁺ ions in a series of Hf:Er:LiNbO₃ crystals with variable Hf content and fixed Er content are reported. Unpolarized UV-VIS-NIR absorption spectra, upconversion fluorescence spectra excited at 800 nm, and microsecond time-resolved spectra excited at 400 nm and 800 nm by 800 nm femtosecond laser were measured at room temperature. The HfO₂ incorporation has influence on Er³⁺ radiative lifetimes, and fluorescence branching ratios. For Hf(4 mol %):Er(1 mol %):LiNbO₃, Ω₂=2.63×10^-20 cm², Ω₄=2.86×10^-20 cm², and Ω₆=0.72×10^-20 cm². Ω₂<Ω₄ is contrary to the Er³⁺ general trend of Ω₂>Ω₄>Ω₆ when the Hf content is below its threshold concentration. In addition, the sum of Ω increases with the Hf content when the HfO₂ content below 6 mol % is unfamiliar. The upconversion mechanism is discussed in this work. PACS 71.20.Eh; 77.84.Dy; 42.62.Fi; 42.65.Ky     

Magnetic properties of LiNi<Subscript>0.5</Subscript>Mn<Subscript>0.47</Subscript>Al<Subscript>0.03</Subscript>O<Subscript>2</Subscript> as positive electrode for Li-ion batteries

The layered LiNi_0.5Mn_0.47Al_0.03O₂ was synthesized by wet chemical method and characterized by X-ray diffraction and analysis of magnetic measurements. The powders adopted the α-NaFeO₂ structure. This substitution of Al for Mn promotes the formation of Li(Ni_0.47²⁺Ni_0.03³⁺Mn_0.47⁴⁺Al_0.03³⁺)O₂ structures and induces an increase in the average oxidation state of Ni, thereby leading to the shrinkage of the lattice unit cell. The concentration of antisite defects in which Ni²⁺ occupies the (3a) Li lattice sites in the Wyckoff notation has been estimated from the ferromagnetic Ni²⁺(3a)–Mn⁴⁺(3b) pairing observed below 140 K. The substitution of 3% Al for Mn reduces the amount of antisite defects from 7% to 6.4–6.5%. The analysis of the magnetic properties in the paramagnetic phase in the framework of the Curie–Weiss law agrees well with the combination of Ni²⁺ (S = 1), Ni³⁺ (S = 1/2) and Mn⁴⁺ (S = 3/2) spin-only values. Delithiation has been made by the use of K₂S₂O₈. According to this process, known to be softer than the electrochemical one, the nickel ions in the (3b) sites are converted into Ni⁴⁺ in the high spin configuration, while Ni²⁺(3a)–Mn⁴⁺(3b) ferromagnetic pairs remain, as the Li⁺(3b) ions linked to the Ni²⁺(3a) ions in the antisite defects are not removed. The results show that the antisite defect is surrounded by Mn⁴⁺ ions, implying the nonuniform distribution of the cations in agreement with previous NMR and neutron experiments.     

High-sensitivity detection of NO2 using a 740 nm semiconductor diode laser

 An AlGaAs diode laser was used to detect NO₂ absorption lines belonging to the (0 0 0)–(2 13 1) vibrational band, within the X˜² A ₁ electronic ground state, at 739 nm. A simple absorption spectrometer based on wavelength-modulation spectroscopy with second-harmonic detection was developed. The minimum detectable pressure of pure NO₂ was 0.1 μbar with 2 m absorption path-length, corresponding to an absorbance of 10^-6. High-sensitivity detection of NO₂ was also performed in the presence of N₂ and air at different total pressures: The effects on the detection limit of our apparatus were accurately investigated. The minimum NO₂ concentration at 500 mbar of air was measured to be 2 ppm. Received: 11 June 1996 / Revised version: 11 October 1996     

Accuracy in determination of the temperature and partial pressure of CO<Subscript>2</Subscript> in CO<Subscript>2</Subscript>:N<Subscript>2</Subscript>:H<Subscript>2</Subscript>O:NO<Subscript>2</Subscript> mixtures by multiple-frequency laser probing

We present the results of analysis of the errors introduced by hot-band transitions 11¹0-01¹1, 03¹0-01¹1, 12⁰0-12⁰1 of the CO₂ molecule and the absorption lines of the H₂O and NO₂ molecules in determination of the temperature and partial pressure of CO₂, included in the gas mixture CO₂: N₂:H₂O: NO₂ at atmospheric pressure, by multiple-frequency laser probing using a CO₂ laser tunable over the lines of the 00⁰1-[10⁰0,02⁰0]_I,II ground-state laser transitions. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 74, No. 6, pp. 810–815, November–December, 2007.     

Impedance spectroscopy study of Pb<Subscript>2</Subscript>P<Subscript>2</Subscript>O<Subscript>7</Subscript> compound

The lead pyrophosphate, Pb₂P₂O₇, compound was prepared by conventional solid-state reaction and identified by X-ray powder diffractometer. Pb₂P₂O₇ has a triclinic structure whose electrical properties were studied using impedance spectroscopy technique. Both impedance and modulus analysis exhibit the grain and grain boundary contribution to the electrical response of the sample. The temperature dependence of the bulk and grain boundary conductivity were found to obey the Arrhenius law with activation energies E _g = 0.66 eV and E _gb = 0.67 eV, respectively. The scaling behavior of the imaginary part of the complex impedance suggests that the relaxation describes the same mechanism at various temperatures.     

Ultra-sensitive ambient ammonia detection using CO<Subscript>2</Subscript>-laser-based photoacoustic spectroscopy

An ambient trace-ammonia sensor that uses resonant photoacoustic spectroscopy and a line-tunable CO₂ laser has been developed. This system achieves a 1 replicate precision of 32 parts-per-trillion (ppt) with an averaging time of 5 s and a total measurement time of 40 s. This 32-ppt precision corresponds to a minimum detectable fractional absorbance of 8.8×10^-9, a minimum detectable absorption coefficient of 9.6×10^-10 cm^-1, and a minimum path-length-normalized detectivity of 1.1×10^-8 Wcm^-1/Hz^1/2. Background interference from CO₂, H₂O, and cell-window absorption were subtracted by switching to a neighboring off-resonance laser wavelength . PACS 42.62.Fi; 82.80.Gk; 82.80.Kq     

Influence of carbon additive on the properties of spherical Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> and LiFePO<Subscript>4</Subscript> materials for lithium-ion batteries

Preparing spherical particles with carbon additive is considered as one effective way to improve both high rate performance and tap density of Li₄Ti₅O₁₂ and LiFePO₄ materials. Spherical Li₄Ti₅O₁₂/C and LiFePO₄/C composites are prepared by spray-drying–solid-state reaction method and controlled crystallization–carbothermal reduction method, respectively. The X-ray diffraction characterization, scanning electron microscope, Brunauer–Emmett–Teller, alternating current impedance analyzing, tap density testing, and electrochemical property measurements are investigated. After hybridizing carbon with a proper quantity, the crystal grain size of active materials is remarkably decreased and the electrochemical properties are obviously improved. The Li₄Ti₅O₁₂/C and LiFePO₄/C composites prepared in this work are spherical. The tap density and the specific surface area are as high as 1.71 g cm⁻³ and 8.26 m² g⁻¹ for spherical Li₄Ti₅O₁₂/C, which are 1.35 g cm⁻³ and 18.86 m² g⁻¹ for spherical LiFePO₄/C powders. Between 1.0 and 3.0 V versus Li, the reversible specific capacity of the Li₄Ti₅O₁₂/C is more than 150 mAh g⁻¹ at 1.0-C rate. Between 2.5 and 4.2 V versus Li, the reversible capacity of the LiFePO₄/C is close to 140 mAh g⁻¹ at 1.0-C rate.     

Dynamics of ions produced by laser ablation of ceramic Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and Al at 193 nm

We study the dynamics of ions produced upon ablation of Al and ceramic Al₂O₃ targets using nanosecond laser pulses at 193 nm (6.4 eV) as a function of the laser fluence from threshold up to 12 J cm⁻². An electrical (Langmuir) probe located at 40 mm from the target surface has been used for determining the ion yield and calculating the kinetic energy distributions. The results for both targets show the existence of a significant amount of ions having kinetic energies >200 eV (≈20% around threshold fluence), and kinetic energies are up to >1.5 keV. The results are related with the existence of direct photonionization processes caused by the photon energy of the laser being higher than the ionization potential of Al (5.98 eV). Comparison of the ion yield when ablating the two types of targets for fluences above threshold to data reported in the literature suggests that the magnitude of the yield and its threshold are parameters depending on the thermal properties of the target rather than on the laser wavelength. Around threshold, the different behavior of ion yield when ablating Al and Al₂O₃ targets suggests that the threshold for neutral aluminium and ion species in the case of ablation of the Al₂O₃ target must be similar.     

Near-infrared laser photoacoustic detection of methane: the impact of molecular relaxation

A photoacoustic sensor has been developed for trace-gas monitoring using a near-infrared semiconductor laser emitting in the 2ν₃ band of methane at 1.65 μm. The apparatus was designed for on-line process control in the manufacturing of the novel low-water-peak fibres developed for optical telecommunications. The importance of collisional relaxation processes in the generation of the photoacoustic signal is reported in the particular case of CH₄ detection in dry O₂ and O₂–N₂ mixtures. The negative influence of these effects results in a strongly reduced and phase-shifted photoacoustic signal, induced by a fast resonant coupling between the vibrational states of methane and oxygen, associated with the slow relaxation of the excited oxygen molecules. An unusual parabolic response of the sensor with respect to the methane concentration has been observed and is discussed. Finally, the beneficial effect of several species, including water vapour and helium, acting as a catalyst to hasten the relaxation of the CH₄–O₂ system, is demonstrated. PACS 42.62.Fi; 33.20.Ea; 34.50.Ez     

<Superscript>29</Superscript>Si MAS-NMR study of oxide conductors derived from the apatite-type La<Subscript>9.33</Subscript>Si<Subscript>6</Subscript>O<Subscript>26</Subscript> compound

The preparation of (La_9.33−2x/3Sr _x □_0.67−x/3)Si₆O₂₄O₂ (0 ≤ x ≤ 2) samples with different amounts of cation vacancies is reported. Structure and unit-cell parameters were deduced by Rietveld analysis of XRD patterns. Structural features that enhance oxygen conductivity in Sr-doped apatites are discussed. Up to three components were detected in ²⁹Si MAS-NMR spectra which change with the amount and distribution of cation vacancies. In general, oxygen conductivity increases with the amount of vacancies at La1 (6h) sites, passing through a maximum for x = 0.4. In the case of activation energy, a minimum is detected near x = 1.2, indicating that entropic and enthalpic change in different ways. The presence of cation vacancies should enhance oxygen hopping along c-axis; however, the analysis of the frequency dependence of conductivity suggests that oxygen motions are produced along three axes.     

Metallic liquid hydrogen and likely Al<Subscript>2</Subscript>O<Subscript>3</Subscript> metallic glass

Dynamic compression has been used to synthesize liquid metallic hydrogen at 140 GPa (1.4 million bar) and experimental data and theory predict Al₂O₃ might be a metallic glass at ∼ 300 GPa. The mechanism of metallization in both cases is probably a Mott-like transition. The strength of sapphire causes shock dissipation to be split differently in the strong solid and soft fluid. Once the 4.5-eV H-H and Al-O bonds are broken at sufficiently high pressures in liquid H₂ and in sapphire (single-crystal Al₂O₃), electrons are delocalized, which leads to formation of energy bands in fluid H and probably in amorphous Al₂O₃. The high strength of sapphire causes shock dissipation to be absorbed primarily in entropy up to ∼400 GPa, which also causes the 300-K isotherm and Hugoniot to be virtually coincident in this pressure range. Above ∼400 GPa shock dissipation must go primarily into temperature, which is observed experimentally as a rapid increase in shock pressure above ∼400 GPa. The metallization of glassy Al₂O₃, if verified, is expected to be general in strong oxide insulators. Implications for Super Earths are discussed.