本体共聚合制备丙烯/1-丁烯合金及表征

以球形高效负载的TiCl₄/MgCl₂/邻苯二甲酸二异丁酯(DIBP)为催化剂, 采用本体聚合方法进行丙烯与1-丁烯共聚合研究. 考察了共单体效应对共聚活性及聚合物立构规整性的影响; 表征了共聚物的结构. 结果表明, 随着1-丁烯/丙烯投料比的增加, 聚合活性呈先升高后降低的趋势, 在1-丁烯/丙烯摩尔投料比为0.26条件下聚合活性达到最高, 并随着共聚物中1-丁烯含量的增加, 共聚物的熔点明显下降, 分子量降低, 分子量分布变窄, 同时共聚物力学性能有明显提高, 透明度逐渐增加.     

含1,2-亚乙基单元的双酚A聚碳酸酯非光气法合成和表征

以双酚A(BPA),碳酸乙二酯(EC)和碳酸二甲酯(DMC)为原料,制备双酚A二元醇(Ⅰ)和双酚A碳酸酯(Ⅱ),并用红外光谱与核磁共振波谱对其结构进行表征.通过Ⅰ与Ⅱ的共缩聚反应及Ⅱ的自聚实现了主链中含有—CH2CH2—单元的双酚A型聚碳酸酯(PC)的非光气法合成,用凝胶渗透色谱法(GPC)和TGA-DSC对PC的分子量和热性质进行分析.结果表明,Ⅱ在240℃自聚6h后产物的Mn可达17.6×103,主链中—CH2CH2—单元的引入,可以降低聚合物的Tg,提高其结晶性,所得聚合物具有良好的热稳定性.     

含氰基高性能聚芳醚材料的合成与表征

将合成的含氰基的双二氮杂萘酮单体与二氟芳香单体进行亲核取代反应, 制备了三种含氰基的新型聚芳醚, 并用TGA, DSC和GPC等分析手段对其综合性能进行表征. 结果表明, 含氰基聚芳醚具有优异的热稳定性(T5%>492 ℃)、较高的玻璃化转变温度(Tg=262~320 ℃)和良好的溶解性能, 易溶于氯代烷烃(如氯仿)和极性非质子性溶剂(如DMAc, DMF, NMP等).     

含有偶氮苯和1,3,4-噁二唑结构聚合物的合成及性能

合成了同时含有偶氮苯和1,3,4-噁二唑结构的新型共轭聚合物(LPOXD),采用FT-IR、UV-Vis、1H NMR、GPC、TGA和DSC测试技术对其结构进行了表征。 结果表明,所得共轭聚合物的特性粘数为0.02960 L/g,Mw和分子量分布指数PDI分别为8500 g/mol和1.55。 质量损失5%的温度为290 ℃,Tg为92.8 ℃。 长烷氧基侧链的引入极大地提高了LPOXD在氯仿和四氢呋喃等有机溶剂中的溶解性。 采用紫外-可见吸收光谱、荧光光谱及循环伏安对LPOXD的光电性能进行了研究。 结果表明,在365 nm紫外光照射下,LPOXD中偶氮苯发生反-顺异构化;350 nm光激发下,LPOXD在蓝紫光波长范围内发射荧光;循环伏安测试得出LPOXD最高占有轨道(HOMO)能量和最低空轨道(LUMO)能量分别为-5.96和-3.17 eV。     

Progress of Polymerization of D,L-Lactide Through Differential Scanning Calorimetry and Gel Permeation Chromatography

Melt polymerization conditions for D,L-lactide initiated with tetraphenyltin were studied with regard to polymer molecular weight. The present study was undertaken to investigate the progress of polymerization of D,L-lactide through differential scanning calorimetry (DSC), and also to explore the correlation between melt polymerization conditions and molecular weight. The physical characteristics, such as glass transition temperature (Tg) of the polymer and melting transition (Tm) of D,L-lactide are correlated with GPC data. DSC data shows that the Tm of D,L-lactide is 122.8 at 150°C polymerization time. ΔHf is 83.2 J g-1, and Tg of polymer is untraceable. At 180°C the Tm is 101.4°C, ΔHf is 34 J g-1, and Tg is around 29.5°C. The drop in Tm and ΔHf clearly shows the conversion of D,L-lactide to polymer. The maximum increment to molecular weight of polymer is achieved at 160°C and 8 h. After a short induction period, the slow polymerization of D,L-lactide resulted in maximal molecular weight followed by an almost constant value of molecular weight. This revised version was published online in July 2006 with corrections to the Cover Date.     

Synthesis of the block copolymer of styrene and 1-butene with a novel supported Ti-catalyst

The present investigation deals with sequential block copolymerization of styrene and 1-butene with a novel MgCl₂-supported TiCl₄ catalyst modified with a rare earth compound NdCl_x(OR)_y (SN-1 catalyst), which was developed in our laboratory. The catalytic activities are 1300–2500 g/g·Ti·h. Analyses of copolymers with solvent extraction, ¹³C-NMR, WAXD, GPC, and DSC was performed. The results indicate that the SN-1 catalyst selectively gave crystalline diblock copolymers of isotactic polystyrene and isotactic poly(1-butene), with the styrene unit content of 30–60 mol %. © 1996 John Wiley & Sons, Inc.     

Synthesis, characterization, and cure properties of phosphorus-containing epoxy resins for flame retardance

An organophosphorus compound, 10-(2,5-dihydroxyl phenyl)-9, 10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DHPDOPO), was synthesized through the reaction of 9,10-dihydro-9-oxa-10-phosphaphnanthrene-10-oxide (DOPO) and p-benzoquinone, and characterized by elemental analysis, Fourier transform infrared spectrum (FTIR), and ¹H-NMR and ³¹P-NMR spectroscopes. Consequently, the phosphorus-containing epoxy resins with phosphorus content of 1 and 2 wt.% were prepared via the reaction of diglycidyl ether of bisphenol-A with DHPDOPO and bisphenol-A, and confirmed with FTIR and gel permeation chromatography (GPC). Phenolic melamine, novolak, and dicyanodiamide (DICY) were used as curing agents to prepare the thermosetted resins with the control and the phosphorus-containing epoxy resins. Thermal properties and thermal degradation behaviors of these the thermosetted resins were investigated by using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Phenolic melamine-cured resins exhibited higher glass transition temperatures than the other cured resins due to the high rigidity of their molecular chain. TGA studies demonstrated that the decomposition temperatures of the novolak-cured resins were higher than those of the others. A synergistic effect from the combination of the phosphorus-containing epoxy resin and the nitrogen-containing curing agent can result in a great improvement of the flame retardance for their thermosetted resins.     

Influence of molecular weight distribution and long chain branching on the glass transition temperature of polycarbonate

Molecular weight distribution and long chain branching were taken into account for the glass transition temperature (Tg)-molecular weight (M) relationships for bisphenol-A polycarbonate. A new form of the four-variable equation for Tg is proposed for polydisperse branched polymers. The extended equations were compared with the experimental results on Tg and M averages; they were also applied for characterization of branched polymer by the combined GPC/V and DSC methods.     

不同结晶度的乙二醇及其水溶液玻璃化转变与焓松弛

为了考察晶体成分对无定形成分玻璃化转变和结构松弛行为的影响,利用差示扫描量热法(DSC),结合低温显微技术,研究了乙二醇(EG)及其50％水溶液在不同结晶度时的玻璃化转变和焓松弛行为.采用等温结晶方法控制骤冷的部分结晶玻璃体中的晶体份额.DSC结果表明,对于部分结晶的EG,只有单一的玻璃化转变过程,而对于50％EG,当结晶度不同时,不同程度地表现出两次玻璃化转变（无定形相Ⅰ和无定形相Ⅱ）.相Ⅰ的玻璃化转变温度和完全无定形态的含水EG的玻璃化转变温度相一致;相Ⅱ的玻璃化转变温度要比此温度约高6 ℃.低温显微观察结果印证了DSC实验结果.DSC等温退火的实验和KWW(Kohlrausch-Williams-Watts)衰变函数分析结果表明,EG无定形和50％EG中的两种无定形有不同的焓松弛行为.     

Synthesis and properties of two novel copolymers based on squaraine and fluorene units for solar cell materials

Two novel copolymers based on squaraine and fluorine units have been synthesized through palladium catalyzed Suzuki coupling reaction and Sonogashira coupling reaction,respectively.The structures and properties of the two copolymers were characterized by FT-IR.NMR,UV-vis absorbance（Abs）,gel permeation chromatography（GPC）,thermal gravimetric analysis （TGA）,differential scanning calorimetry（DSC） and cyclic voltammetry（CV）.The solution absorption spectrums of P₁ and P₂ show two distinct absorption bands,one locates at 300-500 nm and the other at 600-800 nm.The absorption spectrums of P₁ and P₂ in films are broadened obviously and the spectral responses are extended up to 900 nm.Thermal gravimetric analysis demonstrates that the polymers are stable.Cyclic voltammetry experiment shows that the band gaps of the copolymers are 1.65 eV and 1.67 eV. respectively,suggesting their potential for applications as solar cells materials.     

New Copoly(bisphenol-A)carbonates,Having Hydrophilic Porphyrin Units as End-Groups,Synthesized by Melt-Reacting Processes

The synthesis of some poly(bisphenol-A)carbonates (PCs) containing hydrophilic porphyrin units as end groups, by thermal treatment of commercial PC and 5,10,15-tri{p[ω-methoxy-poly(oxyethylene)]phenyl}20(p-hydroxy phenyl)porphyrin (I) blends, is reported. A suitable choice of reaction temperature, molar composition and reaction time, allowing the extent of the outer-inner transesterification reactions, leads to a gradual insertion of porphyrin units in the polymer chains. The composition of the obtained materials was inferred by GPC and MALDI-TOF mass spectrometric analysis.     

PMMA-b-QPDMAEMA的合成及其抗菌活性

以α-溴代丙酸乙酯为引发剂,CuCl/二乙烯三胺为催化剂,采用ATRP法制得5个不同分子量的聚甲基丙烯酸甲酯-聚甲基丙烯酸二甲氨乙酯嵌段共聚物(PMMA-b-PDMAEMA, P¹~P⁵); P¹~P⁵经溴代辛烷季铵化合成了5个聚季铵盐(Q¹~Q⁵),其结构和性能经¹H NMR, FT-IR, GPC和DSC表征。结果表明：P⁴和Q⁴的玻璃化转变温度分别为109.67 ℃和117.95 ℃。采用平板活菌计数法研究了Q¹~Q⁵对金黄色葡萄球菌(S. aureus)和大肠杆菌(E. coli)的抗菌活性。结果表明：Q¹~Q⁵对S. aureus的抗菌活性优于E. coli,其MIC值分别为300 mg·L^-1, 250 mg·L^-1, 275 mg·L^-1, 225 mg·L^-1和150 mg·L^-1。     

Polyazomethines derived from polynuclear dihydroxyquinones and siloxane diamines

New polyazomethines have been synthesized based on polynuclear dihydroxy quinones (5,8-dihydroxy-1,4-naphthoquinone and 1,4-dihydroxyanthraquinone) and siloxane diamines differing by the siloxane sequence length (1,3-bis(3-aminopropyl)tetramethyldisiloxane and α,ω-bis(3-aminopropyl)oligodimethylsiloxane having about 12 siloxane units/sequence). The structures were verified by spectral analyses. Solubility tests, GPC and viscosity measurements were performed. Some properties of the resulted polymers were investigated by thermal (TGA and DSC), electrical, spectral (UV-Vis) and electrochemical (differential pulse voltammetry) methods.     

Preparation of polymeric alcohol bearing oligo(oxyethylene) moiety by radical polyaddition through ketyl radical

Hydrophilic polymers having both oligo(oxyethylene) moieties and tertiary alcohol units in the main chain were prepared by the radical polyaddition of the dike-tones with distyryl compounds by using samarium(II) iodide as an electron transfer agent. Polyaddition of 4,4′-(1,4-phenylene)bis-2-butanone or 6,9-dioxatetradeca-2,13-dione with distyryl compounds such as 1,15-di(4-ethenylphenyl)-2,5,8,11,14-pentaoxapentadecane, 1,18-di(4-ethenylphenyl)-2,5,8,11,14,17-hexaoxaoctadecane, or 1,21-di(4-ethenylphenyl)-2,5,8,11,14,17,20-heptaoxaheneicosane resulted in the formation of the corresponding polymeric alcohols in moderate yields (46–75%). The produced polymers showed high solubility in common solvents, and their molecular weights estimated by GPC (THF, polystyrene standard) were 5200–8100. No serious difference in the molecular weight of the polymer between after and before the treatment with cerium ammonium nitrate indicated that the produced polymers were inert under the oxidative condition where oxidative cleavage of the main chain of poly(vinyl alcohol) takes place. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 715–720, 1997     

Synthesis of thermoresponsive polystyrene-based comb-type grafted poly(N-isopropylacrylamide)

Narrowly distributed polystyrene-g-p(N-isopropylacrylamide) (PSt-g-PNIPAM) was prepared by atom transfer radical polymerization (ATRP) of N-isopropylacrylamide using the brominated polystyrene as macroinitiator and CuCl combined with hexamethyltriethylenetetramine as catalyst. Fourier transform infrared (FT-IR) spectroscopy and nuclear magnetic resonance (NMR) spectroscopy confirmed the structure of PSt-g-PNIPAM. The gel permeation chromatography (GPC) showed that the graft copoly- mer had a single distribution peak with molecular weight, Mn (g/mol) of 19815 g/mol (using polystyrene as the standard). Differential scanning calorimetry (DSC) revealed that due to both effects of hydro- phobic isopropyl groups and hydrogen bonds in the amide group, the glass transition temperature (Tg) of PSt-g-PNIPAM enhanced 16.0 ℃ compared to the Tg of the polystyrene.     

Synthesis and Properties of Silphenylene-containing Epoxy Resins with High UV-stability

Two novel silphenylene-containing cycloaliphatic epoxy resins, 1,4-di [2-(3, 4-epoxycyclohexylethyl) dimethylsilyl] benzene (DEDSB) and 1,3,5-tri [2-(3, 4-epoxycyclohexylethyl) dimethylsilyl] benzene (TEDSB) were synthesized through in situ Grignard reaction and hydrosilylation, and characterized by FT-IR and ¹H-NMR. They were colorless transparent viscous liquids. Methyhexahydrophthalic anhydride (MeHHPA) was used to cure the epoxy resins to give glassy solids with high optical clarity. Differential scanning calorimetry (DSC) results indicated that DEDSB and TEDSB showed similar curing reactivity. The cured TEDSB had a higher glass transition temperature, a higher storage modulus and a lower coefficient of linear thermal expansion than the cured DEDSB due to a higher crosslink density. The cured silphenylene-containing epoxy resins exhibited a much higher resistance to discoloration under UV irradiation than the commonly used epoxy resins diglycidyl ether of bisphenol-A (DGEBA). XPS analysis revealed that they were much less susceptible to photo-oxidation than DGEBA.     

Synthesis and Characterization of Novel Organic／Inorganic Hybrid Polymers Containing Polyhedral Oligosilsesquioxanes

Hybrid polymers, poly(vinyl pyrrolidone-co-isobutyl styryl polyhedral oligomeric silsesquioxanes)s (PVP-POSS) were synthesized by one step polymerization and characterized using GPC and DSC. Addition of POSS significantly increases the Tg of polyvinylpyrrolidone at a fair high POSS content and obtained high molecular weight polymers with very narrow molecular distribution. The POSS content in the resulted hybrids can be controlled by varying the POSS feed ratio.     

Studies on thermotropic liquid crystalline polyurethanes. III. Synthesis and properties of polyurethane elastomers by using various mesogenic units as chain extender

Four series of thermotropic polyurethane elastomers (TPUEs) were synthesized in this study. The hard segments were formed by using 4,4′-methylenedicyclohexyl diisocyanate (H₁₂MDI) reacted with various mesogenic units, such as benzene-1,4-di(4-iminophenoxy-n-hexanol), benzene-1,4-di(4-iminophenol), and 3,3′-(4,4′-biphenylene)dipropanol, which also acted as the chain extender. Poly(oxytetramethylene)glycols (PTMEGs), PTMEG-2000 (M_n 2,000) and PTMEG-1000 (M_n 1,000) were used as a soft segment. The structures of all synthesized thermotropic liquid crystalline polyurethanes (TLCPUs) were characterized by FTIR spectroscopy. The effects of mesogenic units on the LC properties and elastic behaviors of LCPUs were studied. It was difficult to show LC behaviors for the PU elastomers derived from the mesogenic units with a lower aspect ratio, such as 3,3′-(4,4′-biphenylene)dipropanol, or the long soft segments, PTMEG-2000. In addition, these PU elastomers show better elastic properties by using a higher aspect ratio mesogenic unit as the chain extender, such as benzene-1,4-di(4-iminophenoxy-n-hexanol and benzene-1,4-di(4-imino-phenol)). The thermal properties were investigated by DSC measurements, thermal optical polarized microscopy, wide angle X-ray diffraction, dynamic mechanical analysis, and thermogravimetric analysis. The mechanical properties were measured by a tensilemeter. © 1996 John Wiley & Sons, Inc.     

对苯二甲酸乙二醇2-甲氧基-1,3-丙二醇共聚酯的合成与表征

以源自甘油的2-甲氧基-1,3-丙二醇（MPD）代替1,3-丙二醇,采用直接酯化法,合成了一系列不同配比的对苯二甲酸(PTA)乙二醇(EG)2-甲氧基-1,3-丙二醇共聚酯PET-PMT（简称PEMT）,并对其进行表征。 用红外光谱、核磁共振研究了PEMT的结构和化学组成;用GPC测定了不同配比PEMT的相对分子质量与相对分子质量分布;乌氏粘度计测定了其粘度;用DSC分析了其结晶性能。 结果表明,共聚酯PEMT中PMT链段的实际接入量比投料的MPD比例高。 且PEMT的粘度明显高于PET的粘度。 第三单体MPD的引入,使共聚酯PEMT的结晶性能下降。 MPD与PTA的投料摩尔比小于0.4时,共聚酯PEMT的结晶与熔融行为类似于PET。 所合成共聚酯PEMT-40（实际n（PMT）∶n（PET）=24∶76）其质均相对分子质量（Mw）为50 216、特性粘度（η）为0.458 dL/g、玻璃化转变温度（Tg）为68.32 ℃、熔点(Tm)为211.07 ℃。 当MPD与PTA的投料摩尔比大于0.6时,共聚酯为无定形共聚物。     

Transesterification and polymerization reactions of aliphatic polyesters in supercritical CO2 fluids without the presence of a catalyst

The reactions or stability of two crystalline polycaprolactones (PCL) and one amorphous poly(d,l-lactic acid) (dl-PLA) in supercritical CO₂ fluid (scCO₂) at 35 °C and 34.5 MPa without the presence of a catalyst were investigated using gel permeation chromatography (GPC), nuclear magnetic resonance spectroscopy (NMR), and differential scanning calorimetry (DSC). The two PCLs having 80,000 and 10,000 in number average molecular weights (), denoted by PCL8 and PCL1, respectively, and dl-PLA having 74,000 in were studied. Carbon 13 NMR data found these polyesters no formation of carbonate linkages after treatments in scCO₂, indicating that the CO₂ did not copolymerize with the PCLs and dl-PLA. GPC data found that the molecular weights of PCL8/PCL1 blends considerably varied with the treatment time while the components of the blends negligibly changed throughout 6 h of treatments in scCO₂. These GPC data suggested that transesterification reactions occurred between PCL8 and PCL1. DSC data found that PCL8 co-crystallized with PCL1 and the treatments enhanced the melting temperatures and crystallinities of the blends. GPC data also found that the molecular weights of dl-PLA and PCL8/dl-PLA blends considerably varied with the treatment time in scCO₂. From the variations of molecular weights, it could be suggested that transesterifications and polymerizations both occurred in the PCL8/dl-PLA blends, with the polymerizations predominating over the transesterifications. This predomination in polymerizations lowered with increasing PCL8 content in the blends. DSC data found that the amorphous dl-PLA could be induced to crystallize by scCO₂, giving a heating endotherm at near 122 °C. Following scCO₂ treatments, enhancements of the melting temperature and crystallinity of PCL8 in the PCL8/dl-PLA blends were found, although these enhancements fluctuated with the treatment time.