Modeling of pulsed spark discharge in water and its application to well cleaning

This paper presents a simulation model for the generation of strong pressure wave by means of pulsed spark discharge in water and its application to well cleaning. In the simulation model, one-dimensional time-dependent magnetohydrodynamic equations are coupled to a capacitive discharge circuit equation. A cylindrical conducting spark channel formed by electrical breakdown of water gap between a pair of electrodes is treated as a load of which resistance and inductance are allowed to change with time. For describing the spark channel properties accurately, precise calculations on thermodynamic properties and electrical conductivity are included in the simulation model. The simulation results show an excellent agreement with the experimentally measured shock pressure as well as the current and voltage waveforms. The simulation reveals that Joule heating of the spark channel during the very early phase of electrical discharge plays a key role in the formation of shock wave in water. The voltage on a capacitor at breakdown, the circuit inductance, and the resistance of the spark channel are found to be the most important parameters for the shock wave formation. With this technique, a pilot test for the cleaning of a clogged well has been performed in a water well which was constructed as a test-bed for riverbank filtration near the Anseong-cheon (river) in Korea. Well treatments have been carried out with an electrical energy of 510 J stored on a pulsed power system, at which the maximum shock pressure is measured to be around 7 MPa at the position of the well screen, i.e. 0.1 m away from the spark gap. A slug test shows 2.9 times improvement in the hydraulic conductivity of the well, which, combined with a visual inspection inside the well using an underwater camera, clearly demonstrates that the strong pressure wave generated by underwater spark discharge can effectively remove almost all incrustations formed in the well screen and thus improve well performance. Operating parameters for controlling the strength of shock pressure are discussed using the simulation model for extensive applications of the present technique to various types of water wells.     

Study of shock waves interacting with Ar and N<Subscript>2</Subscript> low pressure dc discharges

Acoustical shock waves (Mach number <2) generated in situ by spark gap are propagated in weakly ionized dc discharges working at low pressure (399 Pa) and containing either Ar or N₂ gas. The electrical characterization and the laser deflection technique are used to measure the characteristics of dc discharge (such as voltage, resistance and power of discharge) and the structure and velocity of shock wave, respectively. The results stress the importance of atomic and molecular nature of the gases in affecting the power deposition and the shock wave properties.     

微波瑞利散射法测定空气电火花激波等离子体射流的时变电子密度

大气压空气电火花激波等离子体射流的电子密度在亚微秒时间尺度上瞬变,其电子密度的测定很难.基于微波瑞利散射原理,本文测量了空气电火花冲击波流注放电等离子体射流的时变电子密度.实验结果表明:测量系统的标定参数A为1.04 × 105 V·Ω·m–2;空气流注放电等离子体射流的电子密度与等离子体射流的半径和长度有关,结合高速放电影像展示的等离子体射流的等效半径和等效长度,测定的电子密度在1020 m–3的量级,且随时间先快速增长至峰值再成指数衰减.此外,本文还探讨了等离子体射流的不同等效尺度对测定结果的影响;分析结果表明,采用时变等效半径和时变等效长度的计算结果最有效,且第1个快速波峰是由光电离的电离波导致的.     

Two‐dimensional magnetosonic shock wave propagation in dense electron–positron–ion plasmas

Two‐dimensional (2D) magnetosonic wave propagation in magnetized quantum dissipative plasmas is studied. The plasma system is comprised of inertial ions, inertia‐less electrons, and positrons. The multi‐fluid quantum hydrodynamic model is used, in which quantum statistical and quantum tunnelling effects of electrons and positrons are included. Reductive perturbation analysis is performed to derive the Zabolotskaya–Khokhlov equation for the 2D propagation of a magnetosonic shock wave in a magnetized qauntum plasma. The effects of varying the different plasma parameters such as positron density and magnetic field intensity on the propagation characteristics of magnetosonic shock waves are discussed with non‐relativistic degenerate plasma parameters in astrophysical plasma situations.     

Characteristics and application of laser-generated acoustic shock waves in air

When a high-power laser beam is focused at a point, the air at the focal point is heated to temperatures of thousands of degrees within several nanoseconds and breaks down. This generates a spark that, in turn, is accompanied by an acoustic shock wave. The acoustic shock waves generated by focussing the beam from a pulsed laser with a 1064 nm wavelength and a power of 800 mJ per pulse have been measured using 1/4″ and 1/8″ B&K microphones. Nonlinear sound levels are observed up to 1.5 m from the laser-induced sparks. Beyond a certain region close to the source, levels are found to decrease in a manner consistent with spherical spreading plus nonlinear hydrodynamic losses. Analysis of the waveforms shows that the acoustic pulses associated with the laser-induced sparks are more repeatable and have higher intensity than those from an electrical spark source. Laser-generated acoustic shock waves are ideal for simulating a blast wave or a sonic boom in the laboratory and for studying the associated propagation effects. To illustrate this application, the propagation of the laser generated shock waves over a series of different hard, rough surfaces has been investigated. The results show the distinctive influences of ground roughness on the propagation of the shock wave.     

Mechanism of laser-induced plasma shock wave evolution in air

A theoretical model is proposed to describe the mechanism of laser-induced plasma shock wave evolution in air. To verify the validity of the theoretical model, an optical beam deflection technique is employed to track the plasma shock wave evolution process. The theoretical model and the experimental signals are found to be in good agreement with each other. It is shown that the laser-induced plasma shock wave undergoes formation, increase and decay processes; the increase and the decay processes of the laser-induced plasma shock wave result from the overlapping of the compression wave and the rarefaction wave, respectively. In addition, the laser-induced plasma shock wave speed and pressure distributions, both a function of distance, are presented.     

Effects of the dust size distribution on shock waves in dusty plasma

By using a Korteweg-deVries-Burgers(KdV-Burgers) equation and considering the dust size distribution, we have studied effects of the dust size distribution on the shock wave in dusty plasma. The dependence of characteristics of the shock wave on different dust size distributions has been given. It is found that the speed and amplitude of a shock wave considering the dust size distribution are larger than that of the dusty plasma with the averaged dust size. However, the width of a shock wave considering the dust size distribution is smaller than that of the dusty plasma with the averaged dust size.     

Rayleigh mechanism of local elevation of energy in propagation of a shock wave in an active medium

A mechanism of action of a shock wave on an active medium, which leads to an additional energy release source, is considered. This source moves together with the shock wave front and depends on the magnitude and direction of the electric field applied to the plasma and on the current density in the plasma. The study is a continuation of an earlier publication devoted to the propagation of weak shock waves. Here, we consider shock waves of an arbitrary intensity with an arbitrary mechanism of formation of an additional energy contribution due to variation of the parameters of the medium as a result of passage of the shock wave. Special cases of this effect are the propagation of a shock wave in a plasma and detonation burning.     

冷等离子体放电区长度对爆震特性影响的实验研究

快速高效的起爆对脉冲爆震发动机工作特性的作用十分关键.文章以乙炔为燃料、空气为氧化剂,使用双爆震管研究冷等离子体和火花塞两种点火方式对起爆特性的影响规律.冷等离子体发生器采用自主设计产品,研究中通过改变冷等离子体放电区长度,测试爆震波的传播过程,给出了放电区体积大小对爆震特性的影响.实验结果表明:冷等离子体点火起爆特性明显优于火花塞;在基本保证放电功率不变时,放电区长度的变化对火焰传播时间、火焰传播速度、爆震波峰值压力影响不大.因此,在工程实践中,采用小区域放电能够减少冷等离子的体积且不影响起爆性能.      

激光等离子体的声学诊断研究

提出了利用激光等离子体声波对高功率激光与材料相互作用过程进行了诊断的方法。实际测量了波长０．５３μｍ激光与几种金属材料相互作用的过程，其结果与采用春它方法得到的结果基本吻合。     

Shock Wave Propagation in Gases and Low Temperature Plasma Under Subatmospheric Pressure

Results of investigation of the shock wave dynamics under subatmospheric pressure in neutral gases and weakly ionized low temperature plasma are presented. The characteristics of spherical and plane configuration shock wave excitation and propagation in gases in the pressure region 1 Torr < p <100 Torr are studied. The same is done for the plane configuration shock wave in weakly ionized plasma in the pressure region 1 Torr < p <10 Torr. It is shown that when p = 3 Torr it is still possible to fix successfully the shock wave appearance and propagation in various neutral gases. The pressure dependence of the shock wave propagation velocity and amplitude is determined experimentally. It is shown that when the pressure decreases the shock wave amplitude decrease and the increase of the Mach number take place. In the case of plane shock wave Mach number reaches the value M = 5.2 under the pressure p = 3 Torr. As for shock wave propagation in low temperature plasma, our experiments showed a significant decrease of wave amplitude and simultaneous increase of its velocities up to 35 wave velocity is related to the heating of neutral gases in plasma.     

液体中激光等离子体冲击波波前传播特性研究及测试

将空气中球对称冲击波衰减波前传播公式推广到非完全中心对称情况，根据对光学阴影法对激光等离子体冲击波波前测试数据的计算分析，提出液体中点源激光等离子体冲击波旋转椭球面波前传播公式.并且用声学方法对水中和酒精中的激光等离子体冲击波波前进行实验测试，结果表明测试结果与计算公式相吻合. 关键词： 激光 等离子体冲击波 旋转椭球面     

液相放电等离子体特性与激波特性的数值分析

以能量平衡方程为基础,采用不同的电导率唯象模型描述了液相放电等离子体圆柱形通道特性,得到了通道内半径、温度、电阻、电流和耗散能量随时间的变化关系,还给出了距离放电间隙中心一定距离处的冲击波压力变化,并与前人利用等离子体通道球状模型计算得到的结果进行了比较。结果表明:把等离子体通道看成球状和看成圆柱状在描述通道压力和通道半径时差异显著,而在描述其他物理特性时差别不大;三种电导率模型在描述等离子体通道物理特性时,变化趋势大体相同,而在描述激波特性时,电导率模型σ₂更符合实际;通过对比电学参数与压力参数的变化,就可以在实验中根据实验数据以及具体的研究问题进行模型的适用性选择。     

激光等离子体去除微纳颗粒的热力学研究

微杂质污染一直是影响精密器件制造质量和使用寿命的关键因素之一.对于微纳米杂质颗粒用传统的清洗方式(超声清洗等)难以去除,而激光等离子体冲击波具有高压特性,可以实现纳米量级杂质颗粒的去除,具有很大的应用潜力.本文主要研究了激光等离子体去除微纳米颗粒过程中的热力学效应:实验研究了激光等离子体在不同脉冲数下对Si基底上Al颗粒去除后的颗粒形貌变化,发现大颗粒会发生破碎而转变成小颗粒,一些颗粒达到熔点后发生相变形成光滑球体,这源于等离子体的热力学效应共同作用的结果.为了研究微粒物态转化过程,基于冲击波传播理论研究,得到冲击波压强与温度特性的演化规律;同时,利用有限元模拟方式研究激光等离子冲击波压强和温度对微粒作用规律,得到了颗粒内随时间变化的应力分布和温度分布,并在此基础上得到等离子体对颗粒的热力学作用机制.     

空气中激光支持爆轰波实验及理论分析

为了研究激光击穿空气产生的等离子体爆轰波形成机制和传播规律,利用高能量CO2激光器产生强激光,进行了空气中产生激光支持等离子体爆轰波实验。实验中:设置了诱导靶板,用于诱发和定位空气中的激光支持爆轰波;以激光器升压过程球隙放电产生的光信号作为触发源,触发高时间分辨率(纳秒级)的高速相机,记录了激光支持爆轰波的成长和传播全过程。分析了激光支持爆轰波的形成机理和传播规律。采用C-J爆轰理论,计算了激光支持爆轰波的压力和温度。研究结果表明:激光支持等离子体爆轰波形成初期,等离子体爆轰波发光体为球形;随着时间增加,等离子体爆轰波发光体的形状类似流星,且头部为等离子体前沿吸收层,亮度较高,而尾部等离子体温度较低,亮度较弱。等离子体爆轰波高速向激光源的方向移动,爆轰波速度高达18 km/s,温度约为107K。随着激光强度的减弱,爆轰波速度迅速按指数规律衰减,当爆轰波吸收的激光能量不能有效支持爆轰波传播时,爆轰波转变为冲击波。     

Analysis of the Evolution of a Supersonically Expanding Plasma

A supersonically expanding arc plasma in argon is analyzed both experimentally and theoretically. The plasma is created in a cascaded arc and extracted through a hole in the anode. It emanates in a large vacuum system, where it expands supersonically. This expansion is limited by a shock wave. After the shock wave a subsonic plasma beam is created. A quasi one-dimensional model, based on the conservation of mass, momentum and energy is presented. The shock wave is treated as a discontinuity. The electron density, the gas velocity and the gas temperature are measured as a function of the position in the expansion by means of Stark broadening and Doppler spectroscopy. The model calculations agree well with the measurements, especially in the first part of the supersonic flow.     

水下等离子体声源的冲击波负压特性

基于修正的Rayleigh气泡脉动方程对水下等离子体声源放电产生的 强声冲击波的传播过程进行了分析; 利用Euler方程作为控制方程组, 建立了水下等离子体声源的聚束声场模型, 通过仿真计算获得的传播云图对冲击波负压的形成机理进行了直观的理论分析. 结果表明: 经过聚能反射罩反射汇聚得到的聚束波在反射稀疏波和水的惯性作用下, 聚束波周围水域产生了拉伸, 形成负压区, 如果拉伸力大于水的抗拉上限, 就会使得水中形成不连续现象, 即出现空化气泡; 此外聚能罩边缘处产生的衍射波进一步加剧了负压的产生, 边缘衍射波最终与拉伸波叠加, 使冲击波负压达到最大值; 通过对比仿真波形和实验波形, 从而验证和进一步揭示了冲击波负压的形成原因. 研究结果对认识水下冲击波的传播规律和进一步改进等离子体声源的设计具有指导意义. 关键词： 等离子体声源 冲击波负压 聚束声场模型 气泡     

Theoretical analysis of planar and non‐planar electron ‐ acoustic shock waves in electron‐positron‐ion plasma

The propagation properties of planar and non‐planar electron acoustic shock waves composed of stationary ions, cold electrons, and q‐non‐extensive hot electrons and positrons are studied in unmagnetized electron‐positron‐ion plasma. In this model, the Korteweg‐de Vries Burgers equation is obtained in the planar and non‐planar coordinates. We have investigated the combined action of the dissipation, non‐extensivity, density ratio of hot to cold electrons, concentration of positrons, and temperature difference of cold electrons, hot electrons, and positrons. It was found that the amplitude of shock wave in e‐p‐i plasma increases when the positron concentration and temperature increase. The same effect is observed in the case of kinematic viscosity η. Furthermore, it is noticed that spherical wave moves faster in comparison to the shock waves in cylindrical geometry. This difference arises due to the presence of the geometry term m/2τ. It should be noted that the contribution of the geometry factor comes through the continuity equation. Results of our work may be helpful to illustrate the different properties of shock wave features in different astrophysical and space environments like supernova, polar regions, and in the vicinity of black holes.     

Nonlinear propagation of spark-generated N-waves in air: modeling and measurements using acoustical and optical methods

The propagation of nonlinear spherically diverging N-waves in homogeneous air is studied experimentally and theoretically. A spark source is used to generate high amplitude (1.4 kPa) short duration (40 μs) N-waves; acoustic measurements are performed using microphones (3 mm diameter, 150 kHz bandwidth). Numerical modeling with the generalized Burgers equation is used to reveal the relative effects of acoustic nonlinearity, thermoviscous absorption, and oxygen and nitrogen relaxation on the wave propagation. The results of modeling are in a good agreement with the measurements in respect to the wave amplitude and duration. However, the measured rise time of the front shock is ten times longer than the calculated one, which is attributed to the limited bandwidth of the microphone. To better resolve the shock thickness, a focused shadowgraphy technique is used. The recorded optical shadowgrams are compared with shadow patterns predicted by geometrical optics and scalar diffraction model of light propagation. It is shown that the geometrical optics approximation results in overestimation of the shock rise time, while the diffraction model allows to correctly resolve the shock width. A combination of microphone measurements and focused optical shadowgraphy is therefore a reliable way of studying evolution of spark-generated shock waves in air.     

Evaluation of plasma parameters from measured data on the passage of shock waves through a plasma

Analytic formulas are derived that make it possible to estimate the plasma parameters from measured data on the characteristics of a shock wave that has passed through a plasma. Examples are given of how these formulas can be used to interpret the data from experimental studies of propagation of a shock wave through a gas-discharge plasma. The results obtained can serve as a starting point for a more detailed analysis.