Course of the terpolymerization of ethylene,propylene, and dicyclopentadiene. I. Single initial addition of dicyclopentadiene

Detailed studies were made of the course of the terpolymerization of ethylene, propylene, and dicyclopentadiene to form unsaturated elastomers. All the dicyclopentadiene was added at the start of a polymerization, but the monoolefins were added continuously throughout the run. Under these conditions, unsaturation of the initial polymer is fairly high but decreases steadily as the reaction progresses. From analyses of the initial samples from each run, the catalyst of VCl₄ (with Al₂Et₃Cl₃ cocatalyst), with heptane as the polymerization solvent, was most efficient for introducing unsaturation into terpolymer. This system also produces gel in the terpolymer in the latter stages of reaction, however. Catalysts of VCl₄, VOCl₃, or V(C₅H₇O₂)₃, with Al₂Et₃Cl₃ cocatalyst, in benzene solvent gave terpolymers of quite similar unsaturations. With all systems, terpolymer yield increases very rapidly in the first few minutes of reaction, then very slowly for the remainder of the 30-min. reaction time, reflecting the rapid loss of activity of the vanadium catalysts. Molecular weight growth of the terpolymer prepared in heptane was extremely rapid, reaching a high value in a few minutes. When prepared in benzene, the terpolymers showed a steady increase in molecular weight throughout the reaction but reached only a moderate final value (as expressed by inherent viscosity).     

Vanadium- or vanadylacetylacetonate as a cocatalyst for the terpolymerization of ethylene,propylene, and dicyclopentadiene

Vanadium trisacetylacetonate [V(C₅H₇O₂)₃] and vanadyl bisacetylacetonate [VO-(C₅H₇O₂)₂] were found to be satisfactory catalysts (with Al₂Et₃Cl₃ cocatalyst) for the terpolymerization of ethylene, propylene, and dicyclopentadiene to unsaturated, sulfurcurable elastomers. Polymerization solvents of heptane or benzene were used. Best yields of terpolymers were obtained in benzene. Terpolymers with unsaturations of greater than ?0.20 mole C?C/kg. can be cured with a sulfur-based vulcanzing recipe. Both acetylacetonates produced terpolymers, in benzene, with practically equivalent properties. They also appeared to be nearly equal to corresponding terpolymers made with catalysts of VOCl₃ or VCl₄.     

Easily accessible chiral dicyclopentadiene ligands for rhodium-catalyzed enantioselective 1,4-addition reactions

A variety of novel C₁-symmetric chiral diene ligands based on the dicyclopentadiene (DCP) skeleton were easily prepared from commercially available DCP. The application of these diene ligands in the rhodium-catalyzed asymmetric 1,4-addition of arylboronic acids to α,β-unsaturated carbonyl compounds has been examined and excellent enantioselectivities (up to 97% ee) as well as good yields were achieved under mild reaction conditions.     

Ultrasonic spectroscopic evaluation of the ring‐opening metathesis polymerization of dicyclopentadiene

An in situ ultrasonic spectroscopy technique was used to study the ring‐opening metathesis polymerization of dicyclopentadiene catalyzed by bis(tricyclohexylphosphine)benzylidene ruthenium dichloride. A reaction cell employing a flexible poly(ethylene terephthalate) window for pulse echo ultrasonic spectroscopy was used to monitor the polymerization. The changes in the density, wave speed, acoustic modulus, and attenuation were all simultaneously monitored. In comparison with Fourier transform infrared (FTIR) spectroscopy data, the changes in the density, velocity, and modulus only accurately measured the rate constant for the metathesis of the cyclopentyl unsaturation. The ultrasonic values were within 6% of the values determined by FTIR. The activation energy for metathesis of the cyclopentyl unsaturation was 84 kJ mol^?1, following first‐order kinetics. Rate constants for the polymerization of the norbornyl unsaturation could not be determined by ultrasound. The gel point, vitrification, and qualitative information about the reaction rate could be determined from the change in the attenuation. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1323–1333, 2003     

POLYMERIZATION OF ETHYLENE AND PROPYLENE WITH VCL4-BUTYLLITHIUM CATALYSTS

Polymerization of ethylene and propylene with VCl₄-BuLi (Bu = n-Bu, sec-Bu, tert-Bu) catalysts was investigated. The VCl₄-BuLi catalysts were found to initiate the polymerization of ethylene and propylene. The VCl₄-BuLi catalysts gave an ultra high molecular polyethylene. The effect of the Li /V mole ratio on the polymerization of ethylene with the VCl₄-BuLi catalysts was observed, an the catalyst gave an optimum rate at the Li/V ratio of about 3.0. The polyethylene obtained with the VCl₄-BuLi catalyst was found to be a linear structure. In the polymerization of propylene with the VCl₄-BuLi catalyst, the polymers contain mm contents of 56–66% were produced.     

Copolymers of dicyclopentadiene and tricyclopentadiene

Series of copolymers of dicyclopentadiene and tricyclopentadiene have been prepared by ringopening metathesis polymerization (ROMP) using a catalytic system of [W(=N-phenyl) (2,6-dimethyl phenolate)₄]/n-BuLi. Due to the presence of double bonds, the polymers obtained from ROMP are unstable. Thus the hydrogenation reaction is carried out after ROMP using a catalyst of bis(2,4-pentanediono)nickel/triisobutylaluminium. The polymers obtained were characterized by means of ¹H NMR; the results show an agreement with the proposed structure. Glass transition temperature T _g of the polymers are modulated by the feed mole ratio of dicyclopentadiene and tricyclopentadiene. With the increasing of tricyclopentadiene content, the T _g of the polymers before hydrogenation increases from 153 to 256°C, and the T _g of the polymers after hydrogenation increases from 106 to 188°C. In addition, the different ratio of dicyclopentadiene and tricyclopentadiene in polymer main chains offers different packing patterns to the structure of the copolymers, and leads to their different free volumes and occupied volumes.     

pH‐Responsive ampholytic terpolymers of acrylamide,sodium 3‐acrylamido‐3‐methylbutanoate,and (3‐acrylamidopropyl)trimethylammonium chloride. I. Synthesis and characterization

Low-charge-density ampholytic terpolymers composed of acrylamide, sodium 3-acrylamido-3-methylbutanoate (NaAMB), and (3-acrylamidopropyl)trimethylammonium chloride were prepared via free-radical polymerization in 0.5 M NaCl to yield terpolymers with random charge distributions. NaOOCH was used as a chain-transfer agent during the polymerization to eliminate the effects of the monomer feed composition on the degree of polymerization (DP) and to suppress gel effects and broadening of the molecular weight distribution. The terpolymer compositions were obtained via ¹³C NMR spectroscopy, and the residual counterion content was determined via elemental analysis for Na⁺ and Cl⁻. The molecular weights (MWs) and polydispersity indices (PDIs) were determined via size exclusion chromatography/multi-angle laser light scattering (SEC–MALLS); the terpolymer MWs ranged from 1.3–1.6 × 10⁶ g/mol, corresponding to DPs of 1.6–1.9 × 10⁴ repeat units, with all terpolymers exhibiting PDIs of less than 2.0. Intrinsic viscosities determined from SEC–MALLS data and the Flory–Fox relationship were compared to intrinsic viscosities determined via low-shear dilute-solution viscometry and were found to agree rather well. Data from the SEC–MALLS analysis were used to analyze the radius of gyration/molecular weight (R_g–M) relationships and the Mark–Houwink–Sakurada intrinsic viscosity/molecular weight ([η]–M) relationships for the terpolymers. The R_g–M and [η]–M relationships revealed that most of the terpolymers exhibited little or no excluded volume effects under size exclusion chromatography conditions. Potentiometric titration of terpolymer solutions in deionized water showed that the apparent pK_a value of the poly[acrylamide-co-sodium 3-acrylamido-3-methylbutanoate-co-(3-acrylamidopropyl)trimethylammonium chloride] terpolymers increased with increasing NaAMB content in the terpolymers and increasing ratios of anionic monomer to cationic monomer at a constant terpolymer charge density. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3236–3251, 2004     

A new catalytic system for the copolymerization of dicyclopentadiene with CO: PdCl2/phen/M(CF3SO3)n

A new three-component catalytic system, PdCl₂/phen/M(CF₃SO₃)_n, was studied in the copolymerization of dicyclopentadiene (DCPD) with CO. It was found that the PdCl₂/phen/CF₃SO₃H catalytic system gave a very low catalytic activity, and the PdCl₂/phen/M(CF₃SO₃)_n catalytic system exhibited high activity when M(CF₃SO₃)_n was introduced instead of CF₃SO₃H. The resultant cooligomer was analyzed using various techniques such as FT-IR, ¹H NMR, ¹³C NMR, DSC and TGA. The results indicated that the copolymer was a polyspiroketal (PS) of CO and DCPD. Due to the tension of the ring of DCPD, the degree of copolymerization is low and the degree of crystallinity is also not high. The effects of ligands, M(CF₃SO₃)_n, solvents, 1,4-benzoquinone/PdCl₂ molar ratio, and temperatures on the copolymerization have been discussed in detail. The results showed that this novel catalytic system exhibited highly efficient activity, especially when 1,10-phenanthroline (phen) was used as ligand and Cu(CF₃SO₃)₂ was used as cocatalyst. The corresponding reaction rate was 49 000 g PS/molPd h when the reaction was carried out at 60 °C and 3.0 MPa of CO. The weight average molecular weight (M_w) and the number average molecular weight (M_n) of the resultant cooligomer were 1180 g/mol and 564 g/mol, respectively.     

Ethylene polymerization and ethylene/hexene copolymerizaion with vandium catalysts bearing thiophenolphosphine ligands

Vanadium(Ⅲ) complexes bearing thiophenol-phosphine ligands (2a-2b) (2-R-6-PPh2-C6H2S) VCl2(THF)2 (2a: R=H; 2b: R=Me3Si) were prepared from VCl3(THF)3 by treating with 1.0 equiv of the ligand in tetrahydrofuran in the presence of excess triethylamine. The two complexes were characterized by FTIR and mass spectra as well as elemental analyses. On activation with Et2AlCl, these complexes exhibited high catalytic activities (up to 22.1 kg PE/(mmolV·h·bar)) even at high temperature (70℃), and produced high molecular weight polymers with unimodal molecular weight distributions, indicating the polymerization took place in a single-site nature. This result may be attributed to benefits of introduction of second-row donor atoms for adjusting charge density of the vanadium centers. In addition, these complexes also exhibited high catalytic activities for ethylene/1-hexene copolymerization. Catalytic activity, comonomer incorporation and polymer molecular weight can be controlled in a wide range by the variation of catalyst structure and the reaction parameters such as Al/V molar ratio, comonomer feed concentration and polymerization reaction temperature.     

Thermally reversible covalently bonded linear polymers prepared from a dihalide monomer and a salt of dicyclopentadiene dicarboxylic acid

Alkali and earth‐alkali salts of dicyclopentadiene dicarboxylic acid (DCPDCA) were prepared and employed as monomers in the polyesterification with an α,ω‐dihalide monomer, such as 1,4‐dichlorobutane (DCB), 1,4‐dibromobutane (DBB), α,α′‐dichloro‐p‐xylene (DCX), and α,α′‐dibromo‐p‐xylene (DBX). Novel linear polymers that possessed repeating moieties of dicyclopentadiene ( DCPD ) in the backbone were thus prepared. The IR and NMR spectra indicated that poly(tetramethylene dicyclopentadiene dicarboxylate) (PTMDD) with a number‐average molecular weight (M_n ) of about 1× 10⁴ and poly(p‐xylene dicyclopentadiene dicarboxylate) (PXDD) with a M_n of 4–6 × 10³ were obtained with an yield of about 80% via the polyesterification of the alkali salts with DBB and DCX, respectively. The reaction was carried out in the presence of a phase transfer catalyst, such as BzMe₃NBr or poly(ethylene glycol), in DMF at 100 °C for 4 h. Oligomers with a lower M_n (1–2 × 10³) were obtained when the earth‐alkali salts were employed as salt monomers. Compared to the irreversible linear polymers, poly(p‐xylene terephthalate) (PXTP) and poly(p‐xylene maleate) (PXM), prepared through the reaction between DCX and the potassium salts of terephthalic and maleic acid, respectively, the specific viscosities (η_sp) of the new linear polymers increased abnormally with the decrease of the temperature from 200 °C to 100 °C. This occurred due to the thermally reversible dedimerization/redimerization of  DCPD moieties of the backbone of the polymers via the catalyst‐free Diels–Alder/retro Diels–Alder cycloadditive reactions. The ratio of the η_sp at 100 °C and 200 °C of the reversible polymers was found to be much higher than that of PXTP and PXM, even when the heating/cooling cycle was carried out several times under a N₂ atmosphere. The obtained results indicated that thermally reversible covalently bonded linear polymer can be obtained by introducing the  DCPD structure into the backbone of the polymer through the polymerization of a monomer containing the  DCPD moiety. The reversible natures of the polymers and oligomers might be useful in preparing easily processable and recyclable polymers and thermosensor materials. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1662–1672, 2000     

Stereospecific polymerization of isobutyl vinyl ether by AlR3–VCln catalysts. I. Influence of preparative conditions of the catalysts

The polymerization of isobutyl vinyl ether by the VCl_n–AIR₃ system was carefully studied. The vanadium components were prepared by the reaction between VCl₄ and AlEt₃ or n-BuLi as a reducing agent. VCl₃·LiCl and VCl₂·2LiCl are the effective catalysts for the stereospecific polymerization of isobutyl vinyl ether. When VCl₃·LiCl is combined with AlR₃, a new catalytic system is formed. The effect of the preparative conditions of the various vanadium component in the AlR₃–VCl_n system shows that the effective vanadium component is trivalent. In the polymerization by VCl₃·LiCl–Al (i-Bu)₃ system, a change of the polymerization mechanism may occur at Al(i-Bu)₃/VCl₃·LiCl ratio at around 5. When the ratio is lower than 5, a cationic polymerization by VCl₃·LiCl takes place predominantly, while at ratios higher than 5, it is suggested that the polymerization proceeds by means of a VCl₃·LiClA–Al(i-Bu)₃ complex by a coordinated anionic mechanism. The polymers obtained by these catalysts are highly crystalline. Styrene was also polymerized by using the same catalysts. VCl₃·LiCl and VCl₃·LiCl–THF complex yielded amorphous polymer by cationic polymerization. When VCl₃·LiCl was combined with 6 mole-eq of Al(i-Bu)₃, the resulting polystyrene was highly crystalline and had an isotactic structure, while the VCl₂·2LiCl–Al(i-Bu)₃ (1:6) system yielded traces of polymer of extremely low stereoregularity. The results indicate that the effective vanadium component at Al/V ≧ 6 is trivalent and that the mechanism is a coordinated anionic one.     

Massenspektrometrische Beobachtungen und chemische Transportexperimente mit den Systemen VCl3/Al2Cl6 und VCl2/Al2Cl6

Mass Spectroscopic Observations and Chemical Transport Experiments with the Systems VCl₃/Al₂Cl₆ and VCl₂/Al₂Cl₆ By mass spectrometry the equilibrium VCl_3,s + 0.5 Al₂Cl_6,g ? VAlCl_6,g has been determined: ΔH°(298) = 25.6(±0.5) kcal; ΔS°(298) = 23.0(±3) cal/K, ΔCp (assumed) = ?4 cal/K. This is approximately in agreement with results determined by ligand field spectroscopy by ANUNDSKÅS and ØYE (A. and Ø.). For the dimerization of VCl_3,g values for ΔH and ΔS have been derived. The molecule VAl₂Cl₉ assumed by A. and Ø. could not been observed by mass spectrometry. For the VCl₂/Al₂Cl₆ complex, observed by chemical transport, A. and Ø. give the formula VAl₃Cl₁₁. This molecule could not been observed by mass spectrometry. This suggests a smaller concentration, compared with the results of A. and Ø. Stabilization of VCl_2,s (by metal-nietal-bonds) shifts the reaction to the left, whith explains the lower complex concentration as well as the larger molecular weight of the complex. With chlorides stabilized by stronger metal-metal bonds (MoCl₃, MoCl₂, Nb₃Cl₈) AlCl₃ complexes are not formed in observable concentrations. The chemical transport of VCl₂ with Al₂Cl₆ needs relatively high temperatures (973 → 873 K). In this case the addition of SiCl₄ hinders the attack of the quartz ampoule by Al₂Cl₆. Using a VCl₃ + VCl₂ mixture, VCl₃ is transported by Al₂Cl₆ (673 → 623 K) into the colder region. If afterwords the ampoule is reversed, VCl₃ again moves into the colder region, but the thermal decomposition of VCl₃ at the same time causes that a VCl₂-residue remains in the hot region.     

Stereospecific polymerization of isobutyl vinyl ether. III. Polymerization with VCl3 • LiCl

The polymerization of isobutyl vinyl ether by vanadium trichloride in n-heptane was studied. VCl₃ ? LiCl was prepared by the reduction of VCl₄ with stoichiometric amounts of BuLi. This type of catalyst induces stereospecific polymerization of isobutyl vinyl ether without the action of trialkyl aluminum to an isotactic polymer when a rise in temperature during the polymerization was depressed by cooling. It is suggested that the cause of the stereospecific polymerization might be due to the catalyst structure in which LiCl coexists with VCl₃, namely, VCl₃ ? LiCl or VCl₂ ? 2LiCl as a solid solution in the crystalline lattice, since VCl₃ prepared by thermal decomposition of VCl₄ and a commercial VCl₃ did not produce the crystalline polymer and soluble catalysts such as VCl₄ in heptane and VCl₃ ? LiCl in ether solution did not yield the stereospecific polymer. It was found that some additives, such as tetrahydrofuran or ethylene glycol diphenyl ether, to the catalyst increased the stereospecific polymerization activity of the catalysts. Influence of the polymerization conditions such as temperature, time, monomer and catalyst concentrations, and the kind of solvent on the formed polymer was also examined.     

A new simple synthesis of soluble high molecular weight polyphenylenes by the cotrimerization of mono- and bifunctional terminal acetylenes

The monofunctional acetylenes, phenylacetylene and m-ethynyltoluene, were each copolymerized with diethynylbenzene in a 1:1 mole ratio by using TiCl₄/3AlEt₂Cl as cyclotrimerization catalyst. The aromatic polymers which were produced were polydisperse with a molecular weight of ～10,000. Variation of catalyst concentration had no effect on the molecular weight profile. An excess of bifunctional acetylene produced some insoluble gel but when some of the monofunctional acetylene was withheld and added only after an initial molecular weight build-up by the excess bifunctional acetylene, soluble polymers with molecular weights of approximately 50,000 were obtained in high yield, provided the overall ratio of mono- to bifunctional acetylene was maintained at 1:1. The resulting polyphenylenes were highly soluble in benzene and chlorinated solvents but gave brittle films. This was attributed to a highly branched structure resulting from a lack of specificity by the catalyst. Thermogravimetric analysis showed the polymers to have high thermal stability.     

Stimuli‐responsive ampholytic terpolymers of N‐acryloyl‐valine,acrylamide, and (3‐acrylamidopropyl)trimethylammonium chloride: Synthesis,characterization, and solution properties

Low‐charge density ampholytic terpolymers composed of acrylamide (AM), (3‐acrylamidopropyl)trimethyl ammonium chloride (APTAC), and N‐acryloyl‐valine were prepared via free‐radical polymerization in 0.5 M NaCl to yield terpolymers with random charge distributions. Sodium formate (NaOOCH) was employed as a chain transfer agent during the polymerization to suppress gel effects and broadening of the molecular weight distribution (MWD). Terpolymer compositions were determined by ¹³C NMR spectroscopy. Terpolymer molecular weights (MWs) and polydispersity indices (PDIs) were obtained via size exclusion chromatography/multi‐angle laser light scattering (SEC‐MALLS). Intrinsic viscosity values determined from SEC‐MALLS data using the Flory–Fox relationship were compared with those determined by low‐shear dilute solution viscometry and found to be in good agreement. SEC‐MALLS experiments allowed examination of radius of gyration‐MW (R_g‐M) relationships and the Mark‐Houwink‐Sakurada intrinsic viscosity‐MW ([η]‐M) relationships for terpolymers. The R_g‐M and [η]‐M relationships indicated little or no excluded volume effects under SEC conditions indicating that the terpolymers were in near theta conditions in an aqueous buffer solution. Potentiometric titration experiments were performed in deionized (DI) water. These studies revealed that the apparent pK_a of the AMVALTAC terpolymers increases with increasing VAL content. The solution properties of low‐charge density ampholytic terpolymers have been studied as functions of solution pH, ionic strength, and polymer concentration. The charge‐balanced terpolymers exhibit polyampholyte behavior at pH values ≥ 6.5. As solution pH is decreased, these charge‐balanced terpolymers become increasingly cationic due to the protonation of the VAL repeat units. Charge‐imbalanced terpolymers generally exhibit polyelectrolyte behavior, although the effects of intramolecular electrostatic interactions (e.g., polyampholyte effects) on the hydrodynamic volume are evident at certain values of solution pH and salt concentration. The solution behavior of the terpolymers in the dilute regime correlates well with that predicted by various polyampholyte solution theories. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3125–3139, 2006     

Polymers derived from fluoroketones. III. Monomer synthesis,polymerization, and wetting properties of poly(allyl ether) and poly(vinyl ether)

The synthesis and polymerization of a series of perhaloalkyl allyl and vinyl ethers derived from perhaloketones is described. Data on the critical surface tension of wetting (γ_c) for high molecular weight polymers of heptafluoroisopropyl vinyl ether and low molecular weight poly(heptafluoroisopropyl allyl ether) is also presented. Preparation of the allyl ethers is a one-step, high-yield displacement reaction between the potassium fluoride–perhaloacetone adduct and an allyl halide, such as allyl bromide. The vinyl ethersare prepared by a two-step process which involves displacement of halide from a 1,2-dihaloethane with a KF–perhaloacetone adduct and dehydrohalogenation of the 1-halo-2-perhaloalkoxyethane to a vinyl ether. Low molecular weight polymers were obtained with heptafluoroisopropyl allyl ether by using a high concentration of a free-radical initiator. The low molecular weight poly(heptafluoroisopropyl allyl ether) had a γ_c of 21 dyne/cm. No polymer was obtained with tributylborane–oxygen or with VCl₃–AIR₃, with gamma radiation, or by exposure to ultraviolet light. High molecular weight polymers were obtained from heptafluoroisopropyl vinyl either by using either lauryl peroxide or ultraviolet light but not by exposure to BF₃–etherate. The γ_c for poly(heptafluoroisopropyl vinyl ether) ranged from 14.2 to 14.6 dyne/cm., and the significance of this value is discussed in relation to the γ_c for poly(heptafluoroisopropyl acrylate).     

Ethylene polymerization and ethylene/hexene copolymerization with vanadium(III) catalysts bearing heteroatom‐containing salicylaldiminato ligands

A series of novel vanadium(III) complexes bearing heteroatom‐containing group‐substituted salicylaldiminato ligands [RN?CH(ArO)]VCl₂(THF)₂ (Ar = C₆H₄, R = C₃H₂NS, 2a ; C₇H₄NS, 2c ; C₇H₅N₂, 2d ; Ar = C₆H₂tBu₂ (2,4), R = C₃H₂NS, 2b ) have been synthesized and characterized. Structure of complex 2c was further confirmed by X‐ray crystallographic analysis. The complexes were investigated as the catalysts for ethylene polymerization in the presence of Et₂AlCl. Complexes 2a–d exhibited high catalytic activities (up to 22.8 kg polyethylene/mmol_V h bar), and affording polymer with unimodal molecular weight distributions at 25–70 °C in the first 5‐min polymerization, whereas produced bimodal molecular weight distribution polymers at 70 °C when polymerization time prolonged to 30 min. The catalyst structure plays an important role in controlling the molecular weight and molecular weight distribution of the resultant polymers produced in 30 min polymerization. In addition, ethylene/hexene copolymerizations with catalysts 2a–d were also explored in the presence of Et₂AlCl, which leads to the high molecular weight and unimodal distributions copolymers with high comonomer incorporation. Catalytic activity, comonomer incorporation, and polymer molecular weight can be controlled over a wide range by the variation of catalyst structure and the reaction parameters, such as comonomer feed concentration, polymerization time, and polymerization reaction temperature. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3573–3582, 2009     

Solution autoxidation of EPDM and termonomers

Oxygen uptake of 3 low molecular weight ethylene-propylene terpolymers (EPDM) and their respective bicyclic diolefin termonomers (dicyclopentadiene, ethylidene norbornene and methyl endomethylene hexahydronaphthalene) has been measured at ? 70°.     

Synthesis of all-cis-3-(2-diphenylphosphinoethyl)-1,2,4-tris(diphenylphosphinomethyl)cyclopentane (Ditricyp) from dicyclopentadiene

A new tetraphosphine, all-cis-3-(2-diphenylphosphinoethyl)-1,2,4-tris(diphenylphosphinomethyl)cyclopentane (Ditricyp), has been synthesised in seven steps from commercially available dicyclopentadiene. The ozonolysis of dicyclopentadiene occurred first on the double bond of the bicycloheptene moiety. A very high chemoselective ozonolysis was observed at −60 °C leading to the diol after reductive treatment. From this diol, cis,cis,cis-3-(2-hydroxyethyl)-1,2,4-tri(hydroxymethyl)cyclopentane was obtained after a second ozonolysis. Mesylation and substitution with Ph₂PLi led to the title tetradiphenylphosphine Ditricyp. The efficiency of this new tetraphosphine ligand for palladium-catalysed coupling reactions has been studied. Satisfactory results in terms of substrate/catalyst ratio have been obtained for Suzuki, Negishi and Sonogashira couplings and also for Heck vinylation reaction. After chromatographic separation, one enantiomer of this ligand associated to palladium was able to induce enantioselective allylic alkylation with modest enantiomeric excess.     

Synthesis,structural characterization,and olefin polymerization behavior of vanadium(III) complexes bearing bidentate phenoxy‐phosphine ligands

Vanadium(III) complexes bearing phenoxy‐phosphine ligands ( 2a–g ) (2‐R₁‐4‐R₂‐6‐PPh₂‐C₆H₂O)VCl₂(THF)₂ ( 2a : R₁ = R₂ = H; 2b : R₁ = F, R₂ = H; 2c : R₁ = Ph, R₂ = H; 2d : R₁ = tBu, R₂ = H; 2e : R₁ = R₂ = Me; 2f : R₁ = R₂ = tBu; 2g : R₁ = R₂ = CMe₂Ph) were prepared from VCl₃(THF)₃ by treating with 1.0 equiv of the ligand in tetrahydrofuran (THF) in the presence of excess triethylamine (TEA). The reaction of VCl₃(THF)₃ with 2.0 equiv of the ligand in THF in the presence of excess TEA afforded vanadium(III) complexes bearing two phenoxy‐phosphine ligands ( 3c–f ). These complexes were characterized by FTIR and mass spectrum as well as elemental analyses. Structures of 2f and 3c were further confirmed by X‐ray crystallographic analyses. Complexes 2a–g and 3c–f were employed as the catalysts for ethylene polymerization under various reaction conditions. On activation with Et₂AlCl, these complexes exhibited high catalytic activities (up to 41.3 kg PE/mmol_V·h·bar) even at high temperature (70°C), and produced high molecular weight polymer with unimodal molecular weight distributions, indicating the polymerization took place in a single‐site nature. Complexes 3c–f displayed better thermal stability than the corresponding complexes 2a–g under similar conditions. In addition, copolymerizations of ethylene and 1‐hexene with precatalysts 2a–g were also explored in the presence of Et₂AlCl. Catalytic activity, comonomer incorporation, and properties of the resultant polymers can be controlled over a wide range by tuning catalyst structures and reaction parameters.© 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012