Swelling and structure of radiation induced near-surface damage in CR-39 and its chemical etching

Systematic measurements of swelling of CR-39 nuclear track detector (NTD) due to irradiation with fission fragments and alpha particles over a wide range of fluences from ²⁵²Cf are presented here. Precisely designed and optimized exposure and chemical etching experiments were employed to unfold the structure of radiation induced surface damage. Delays in the startup of the chemical etching of latent tracks in low radiation fluence detectors are measured and are found to contain important information about structure of the surface damage. Simple atomic scale pictures of radiation induced surface damage and its chemical etching are developed using measurements of radiation induced swelling of CR-39 detectors and nuclear track parameters. The computer code SRIM2010 was utilized for the calculations of basic features of latent tracks of fission fragments and alpha particles in CR-39. Another computer code TRACK_VISION was used to compute parameters of etched tracks. Computations and experimental findings in the paper coherently compose a realistic picture of radiation damage.     

Computation of etched track profiles in CR-39 and comparison with experimental results for light ions of different kinds and energies

Computation of etched track profiles needs the knowledge of the variable track etch rates along the ion trajectories. Using the depth-dependent track etch rates experimentally determined for perpendicularly incident protons, deuterons and alpha particles as well as ⁷Li, ¹¹B, ¹²C, ¹⁴N and ¹⁶O ions of different energies simulations of the track development were performed. Two models of track etching were applied for that purpose recently published in literature. Although the models are based on the same physical fundamentals the results are slightly different. The reasons of the discrepancies were found by analysing the algorithms in detail. Comparison of the calculated track profiles with those determined experimentally from longitudinal sections of the etch pits showed good agreement for non-overetched as well as overetched tracks. The consistency of the whole experimental data set was checked by analysing the correlation of the track etch rates with geometric track parameters for all kinds of ions and etching times covered by the experiments.     

Low energy alpha particle spectroscopy using CR-39 detector

The possibility of using CR-39 to measure the depth profile of ¹⁰B in Si is analysed. The measuring technique exploits the ¹⁰B(n, )⁷Li nuclear reaction. For this reason the track parameters (size, optical properties) of low energy alpha-particles (<1.47 MeV) were studied. The results showed that an energy resolution of about 100 keV could be obtained by an appropriate selection of etching conditions. The profile of ¹⁰B in Si at a depth as small as 1 μm can be measured.     

Radon surveys in Brazil using CR-39

In this work results of two radon daughters survey in Brazil are presented and discussed. Some methodological problems concerning the first survey are pointed out which were corrected for the second survey in order to make a realistic long-term measurement of radon decay products in the air. The technique employed in both surveys was the alpha-spectroscopy using CR-39. The reliability of this technique as well as the results of the second survey are discussed, which indicate a poor correlation between radon and its decay products in the air at the researched dwellings.     

Influence of oxygen on the track etch rate along light ion trajectories in CR-39

The role of oxygen for stabilising radicals to form permanent damages in irradiated samples which are basically important for the etching process of track detectors has been studied. Samples of CR-39 were irradiated with 4 MeV -particles with a fluence of 30 000 particles per cm². The irradiations were performed in three different regimes:

• variation of out-gassing time in vacuum before irradiation;

• no out-gassing time but varied post-irradiation storage times in vacuum;

• variation of both storage times in vacuum before and after irradiation.

Generally, the absence of dissolved oxygen in the irradiated sample results in a decreased detection sensitivity in comparison with the detection properties and track parameters of samples irradiated in air. To determine the sensitivity the depth dependence of the track etch rate v_T(x) along the particle trajectory has been measured. From the observation of the dependence of the decreasing sensitivity on the post-irradiation storage time in vacuum, a lifetime of free radicals of 30 min could be derived. The amount of permanent damages responsible for the etching mechanism is related to the concentration profile of back-diffused oxygen and the REL-dependent radical concentration. This confirms previous results that the detection sensitivity is not a simple function of REL but depends on both REL and x the stronger the deeper within the irradiated sample.     

Track etch rates along the trajectories of nitrogen and oxygen ions in CR-39

Experimental studies on track etch rates in CR-39 performed with protons, deuterons and alpha particles as well as ⁷Li, ¹¹B and ¹²C ions were extended to ¹⁴N and ¹⁶O ions. The results are compatible with the general systematics found for the dependence on the kind of ion and its initial energy. Analysing the etch rate ratios as function of the restricted energy loss (REL), the non-existence of a unique relationship has been confirmed. However, assuming a dependence of the etch rate ratio not only on REL, but also on the depth within the detector where a given REL value occurs, all experimental data could be adjusted. The experiments with ¹⁴N and ¹⁶O ions allow extension of the REL range studied up to about 14 000 MeV/cm. The whole area relevant to neutron-induced charged particles generated within the CR-39 detectors is covered thereby. Having added the data for ¹⁴N and ¹⁶O ions, the array of curves for the etch rate ratio could be expanded up to 14 000 MeV/cm without inconsistencies, demonstrating the compatibility of the new data set also quantitatively.     

Formation of CO2 gas and OH groups in CR-39 plastics due to gamma-ray and ions irradiation

FT-IR spectral studies have been made for CR-39 detectors irradiated by gamma-rays, protons and carbon ions. An absorption peak for CO₂ appeared and grew with the fluence. The peak height was found to decrease gradually by storing in air. Absorbance of the OH group produced by ion bombardment was observed separately from that of adsorbed water using an FT-IR system on the beam line. The concentration of OH group would govern the rate of penetration of chemical agents along the track.     

The fission systematics of (15.9 MeV/u) Au ions in polymer CR-39

It has been demonstrated that high-energy heavy ions undergo fission while propagating in dielectric solids. Since these materials act as particle detectors because of their ability to retain primary ionization damage that can be fixed and enlarged with chemical etching, therefore, in principle, a complete kinematical analysis of fission events is possible. The crucial point in this regard is the availability of a well-calibrated range-energy relation, which is necessary for mass identification. We have developed an analytical method to convert the geometrical parameters of fission fragment tracks into physical parameters using an equation that expresses velocity as a polynomial of mass and range. A set of nine different polynomials was used to represent small regions of mass and range in order to improve accuracy. In the case of (15.9 MeV/u) Au ions incident normally on CR-39, we have found about 200 events which could be categorized as in-flight fission of Au ions inside the body of the detector. Mass distributions and cross sections of fission events have been calculated.     

Extension of alpha particles in CR-39-etched track depth model to heavier ions

In this paper, the previous modeling of protons and alpha particles tracks depth in CR-39 nuclear track detectors was extensively extended to describe tracks of heavier ions. These ions include deuteron, lithium, boron, carbon, nitrogen and oxygen. Based on a compilation of published experimental results related to these ions, a set of empirical fitted model parameters is obtained for each type of ion. The A dependence of these model parameters is obtained.     

Effect of thermal annealing on optical properties of CR-39 polymeric track detector

The samples of CR-39 polymer (TASTRAK, Bristol, England) were annealled thermally at various temperatures ranging from 100°C to 180°C for 1 hour, in air. FTIR spectroscopy reveals the structural degradation of CR-39 polymer due to thermal annealing above its glass transition temperature. Optical band gap of pristine and thermally annealed samples has been determined using UV-Visible absorption spectra. It has been observed that the optical band gap decreases continuously as a result of annealing.      

Study on response of CR-39 detector to light ions

The response of CR-39 detector has been obtained precisely for protons, deuterons, tritons, alpha-particles and lithiumions with energies of a few MeV/nucleon. The track etch rates were determined from the growth curves of pit radius and summarized as the response functions. The accuracy of this method is high enough to discriminate among hydrogen isotopes under a certain condition. The correlation between the response and LET with various cut-off energies has also been examined. It was found that LET is not an unique parameter describing the response function adequately for different ions by the same expression.     

Study of projectile fragmentation in the reaction (158 A GeV) Pb + Pb using CR-39

The fragmentation of Pb ions at 158 A GeV energy produced in the interaction with Pb target has been studied using a CR-39 track detector. A stack comprising of 64 detectors was prepared such that a target of 1 cm thickness was sandwiched between the sheets of CR-39. The purpose of this exposure geometry was to calibrate CR-39 with respect to relativistic heavy ions as well as to study the fragmentation of Pb ions at 158 A GeV energy. The exposure was carried out at the SPS beam facility of CERN at normal incidence with a fluence of . Two detectors from the exposed stack have been selected for this study: one before and the other after the target material. After etching, the detectors were scanned using an optical microscope and the etched track lengths and the diameters of the track openings were measured manually. Considering that the lengths of tracks provide the best charge resolution for Z>65, we have measured track lengths for a sufficiently large number of fragments to identify individual charge states for 65<Z<83. The total charge-changing cross section has also been determined.     

Alpha-particle calibration of CR-39 using a beehive collimator

A device to determine the detection efficiency of CR-39 for alpha particles is presented. A beehive collimator restricted the angle of incidence of alpha particles on a CR-39 sheet, such that the total number of alpha emitters could be determined. This makes it possible to obtain the critical angle of incidence, Θ_C, and the maximum angle of incidence resulting in round (diameter ratio <1.100) etch pits, Θ_max. In this work, these angles were determined for incidence energies around 7.5 MeV (more specifically 6.1 and 8.8 MeV).     

Photoluminescence of irradiation induced defects on CR-39

A gamma-irradiated poly allyl diglycol carbonate solid state nuclear track detector is studied by means of photoluminescence. The irradiation is done using a ⁶⁰Co cell with a dose rate of 7.5 kGy/h. Photoluminescent radiation is recorded with excitation radiation of wavelength 346 nm. A broad luminescent band shows a possible dosemetric property for γ-radiation in the dose range 0.1–8.0 MGy. High-dose irradiation by γ-rays introduces donor and acceptor levels in the forbidden energy gap. The broad band may be attributed to the number of overlapping emissions caused by transitions between these acceptor and donor levels.     

Modification of optical, chemical and structural response of CR-39 polymer by 50 MeV lithium ion irradiation

CR-39 polymer samples were irradiated with 50 MeV lithium ion beam; the fluence was varied in the range 10¹¹–10¹³ ionscm⁻². Irradiation effects were studied using UV–visible, FTIR spectroscopic and X-ray diffraction techniques. The observation of the recorded spectra shows that the detector is sensitive to swift ions irradiation and its UV absorption is influenced by the stopping power (dE/dx)_e. The FTIR spectra does not show any considerable changes due to the irradiation indicating that the detector is chemically stable. No appreciable change in the diffraction pattern of CR-39 polymer after irradiation upto the fluence level of 10¹³ ionscm⁻² is observed, showing its structural stability also.     

Measurement of indoor Rn using CR-39 under a thin film geometry

In this work an assembly for indoor ²²²Rn measurement is presented. This assembly is made up of two acrylic plates (14 cm×14 cm) separated by a distance of 4 mm. To prevent radon daughters from outside entering the assembly (and produce alpha particle tracks striking the CR-39 detector placed in the central region of one of these plates), the borders of these plates were progressively closed, leaving open only a rectangular aperture of 5 mm×4 mm. The size of this opening was determined experimentally, by exposing in two indoor environments assemblies with different apertures as follows: (i) all borders open; (ii) two borders closed; (iii) three borders closed; (iv) four borders closed but one containing a 6 cm×4 mm opening; (v) four borders closed but one containing a 2.5 cm×4 mm opening and (vi) four borders closed but one containing a 0.5 cm×4 mm opening. Track density shows a noticeable decrease between assembly (i) and assembly (iii), remaining constant for smaller openings. Only ²²²Rn, a noble gas, should enter the assembly independently of the opening size.     

Techniques to investigate the characteristic of CR-39 detectors using Am---Be neutron source

Two techniques have been developed to investigate the characteristic of the sensitivity of CR-39 (polyallyldiglycol carbonate) track detector using Am---Be neutron source. The firstis to measure volume track density created by fast neutrons in CR-39 detectors. The second is to measure areal asymptotic track density on the surface of CR-39 sheets. Two types of CR-39—SY-2 CR-39 made in China and another made in USA were calibrated using the techniques. It shows that the two types of CR-39 detectors have nearly the same sensitivity to detect fast neutrons. The techniques developed in this work can be applied to calibration of other track detectors.     

用CR-39对空间重离子的鉴别模型

根据重离子在CR39中能量损失率公式,建立了一个鉴别空间重离子的数学模型LET=cZdRb.通过传能线密度与剩余射程之间的关系曲线,获得了该模型的系数.在实验中发现的CR39蚀刻率与离子有限传能线密度的关系VT=A·(REL)BE<350,被用来与该数学模型相关联,并得到一等式R=A0.0455Z3.18V–1T.最终,借助于标定实验得到了离子鉴别公式Z3.18=64541.08+2.53(dR/dV–1T).     

SHI induced modification in CR-39 polycarbonate by positron annihilation lifetime studies

CR-39 is a polycarbonate widely used as SSNTD for recording nuclear charged particles and in other applications. Latent ion tracks produced in the polymers due to the damage produced by the passage of Swift Heavy Ions contain amorphous material with highest degree of disorder, changing the free volume properties which have strong correlation with the macroscopic properties of the material. Positron annihilation lifetime spectroscopy (PALS) provides direct information about the dimension, content and hole size distribution of free volume in polymers. The effect of irradiation of ⁴⁰Ar (14.9 MeV/n) ions on CR-39 polycarbonate by Positron Annihilation Lifetime Spectroscopy (PALS) is reported here. PALS provides a non-destructive and non-interfering probe, having high detection efficiency for free volume hole properties. From o-Ps lifetime mean free volume hole radius and average free volume of the micro-voids have been calculated. PAL measurement shows an increase in free volume on irradiation.     

Watching at the correlation between the specific track-etch rate and the primary physical parameters of the swift ion interaction with the CR-39

Analysis of etched nuclear tracks in CR-39 solid state nuclear track detectors has recently been made possible by the confocal microscope. This recent innovation has opened up some particularly interesting perspectives. The main originality of this microscopy technique is that it makes it possible to work on numerical, three-dimensional images of chemically etched nuclear tracks in the CR-39. We have studied the performances of this new approach for light ions (H, He, Li and C) with kinetic energies typically of the order of the MeV per nucleus. First, we determined the response functions of the CR-39 for these ions. We were then able to show that aside from decreasing the analysis time of traditional methods, the confocal microscope greatly increases the sensibility of the detection. The aim of this study was to find a correlation between the response functions and the primary physical parameters of the interaction between the ion and the material, such as the linear energy transfer (LET), the restricted energy transfer (REL_ω0), the integrated radial dose or the rate of ionization. Although these parameters presented a strong resemblance to the experimental response functions (they are all “Bragg” curves), none of them were correlated to the response function in an unambiguous way.