Development of a sampling and flow injection analysis technique for iron determination in the sea ice environment

A trace metal clean method for sampling and analysis of iron is set up and applied to sea ice and its associated snow, brine, and underlying seawater sampled during the Antarctic expedition “ARISE in the East” (Antarctic Remote Ice Sensing Experiment, AA03-V1, September-October 2003, 64-65°S/112-119°E, RV Aurora Australis). For clean sampling, a non-contaminating electropolished stainless steel ice corer is designed in conjunction with a polyethylene lathe equipped with Ti chisels to remove possibly contaminated outer layers of ice cores. A portable peristaltic pump with clean tubing is used on the ice to sample the underlying seawater (interface ice-water = 0, 1 and 30 m) and sea ice brine from access holes. Considering the extreme range of salinities (1-100) and Fe concentrations (0.1-100 nM) previously observed in similar environments, it is of paramount importance to set up a simple and sensitive Fe analyser adapted to such gradients. We use a flow injection analysis (FIA) technique and successfully demonstrate its capability to measure Fe concentrations directly in the sample without an on-line preconcentration/matrix separation step. We test the sensitivity, accuracy, precision and long-term stability of the analytical procedure. Also we explore and remediate interferences from a suite of other trace elements, such as Ni, Cd, Cr, Mn, Cu, Zn and Co. Analysis of reference materials NASS-5 and CASS-3 gives a good agreement with the certified values. Repeated measurements over a period of 5 months of an “in-house” Antarctic seawater standard yields a concentration of 1.02 ± 0.07 nM (n = 17, 1σ). The detection limit (3σ of the blank) is on average 0.12 nM. We report here results of the Fe distribution in sea ice that are in good agreement with previously published data. To our knowledge, this work provides the first complete profiles of total dissolvable and dissolved Fe in sea ice.     

A sensitive spectrophotometric method for lead determination by flow injection analysis with on-line preconcentration

A new flow injection (FI) system for the determination of Pb(II) at trace level with a preconcentration step and spectrophotometric detection is proposed. It is based on preconcentration of lead ions on chitosan and dithizone-lead complex formation in aqueous medium (pH 9). The chemicals and FIA variables influencing the performance of the system were optimized and applied to the determination of lead in natural, well, and drinking water samples. It is a simple, highly sensitive, and low cost alternative methodology. The method provided a linear rage between 25 and 250 μg l⁻¹, a detection limit of 5.0 ng ml⁻¹ and a sample throughput of 15 h⁻¹. The obtained results of spiked samples are in good agreement between the proposed method and ICP-AES.     

停留-反相流动注射阻抑光度法测定超痕量铋(Ⅲ)

基于在B-R缓冲溶液介质中,Bi(Ⅲ)对H2O2氧化孔雀石绿(MG)褪色反应的显著阻抑作用,建立了一种停留-反相流动注射阻抑光度法测定超痕量Bi(Ⅲ)的新分析方法,该方法的线性范围为0.001～0.54 ng/L,检出限为9.9×10-4ng/L,相关系数为0.9992。对0.001 ng/LBi(Ⅲ)平行测定11次的标准偏差为1.3%,进样频率为20.9次/h。该方法可直接用于人发和水中的超痕量Bi(Ⅲ)的测定,回收率为96.0%～102.0%。     

The role of flow injection analysis in speciation studies

An overview of the features of flow injection analysis (FIA) which make it a very useful technique for speciation studies is presented. Special emphasis is paid on pre- and post-column coupling as these arrangements allow major speciation problems to be solved.     

细长流动池用于流动注射分析及其水中总磷的测定研究

研制了一个新的高灵敏流动注射分析检测系统。系统主要由一个镓铝砷半导体激光光源(在780nm发射、功率5mW)和一个由聚四氟乙烯材料做成的细长流动池(光径100×1.4mm内径)组成的。与通常10mm流动池相比,测定灵敏度提高10倍左右。用磷钼兰法测定水中总磷的相对标准偏差、检测限(3σ)和线性范围分别为1.0%、0.6μg/L和1.0～50μg/L。     

Immobilization of L-glutamate oxidase and peroxidase for glutamate determination in flow injection analysis system

Streptomyces SP.N 14, isolated from soil samples, produced extracellular L-glutamate oxidase (GOD) in liquid culture. After a two-step ammonium sulfate purification and dextran G-150 chromatography, the specific activity was reached at 28.2 U/mg. The partial purified enzyme and horseradish peroxidase (HRP) were covalently coupled to alkylamine controlled pore glass (CPG) by means of glutaraldehyde. About 200–300 U/g of immobilized GOD and 300–400 U/g of immobilized HRP were obtained. The immobilized enzymes were packed into a teflon tube and used in flow injection analysis (FIA) for glutamate in broth. A good linear range was observed for this immobilized enzyme system at 0.1–2.0 mM, and the precision was 2.8% (n = 25). More than 80 samples were measured within an hour. One enzyme column with about 4 U of immobilized GOD and 5 U of immobilized HRP, applied for 50 assays/d, has been used for more than 50 d. The concentration of L-glutamate remaining lower than 2.0 mM, the determination of glutamate in this system was not affected by pH and temperature within the range of 6.0–7.0 and 25–35‡C, respectively. The system was applied to determine L-glutamate in broth samples during L-glutamate fermentation, and good correlation was achieved between results obtained with the system and with the Warburg’s method.     

Differential electrolytic potentiometry, a detector in flow injection analysis for oxidation-reduction reactions

For the first time, differential electropotentiometry (DEP) is coupled with the flow injection analysis (FIA) technique for detection of oxidation–reduction reactions, and is utilized for quantitative determination of vitamin C in pharmaceutical preparations using 1.0×10⁻³-M cerium(IV) in 0.50-M sulfuric acid as carrier. Two similar platinum electrodes were employed and polarized by a constant current. Optimization by the univariate method was carried out and the optimum conditions for current density, flow rate, sample size and concentration of sulfuric acid were 4 mA, 0.93 ml min⁻¹, 140 μl and 0.25 M, respectively. Vitamin C was determined in the concentration range 100–300 ppm with 0.9987 correlation coefficient and 1.9 standard deviation. The method was applied to the determination of vitamin C in pharmaceutical preparations and no excipient was found to pose any interference thus rendering the method suitable for determination of the drug in pharmaceutical preparations. The accuracy of the method was determined by comparison with the BP standard method.     

Application of hot platinum microelectrodes for determination of flavonoids in flow injection analysis and capillary electrophoresis

The determination of quercetin and rutin by flow injection analysis (FIA) and capillary electrophoresis (CE) using electrochemical detection was described. These flavonoids were determined at normal (unheated) and hot platinum microelectrodes using cyclic voltammetry. When quercetin or rutin is reaching the platinum electrode, a change of the current in the region of the platinum oxide formation is observed. Integration of the current changes in this in this region creates analytical signals in the form of peaks. An increase of temperature to about 76 ?C in a small zone adjacent to the microelectrode causes an increase of the analytical signal by more than 6 times under FIA conditions. This method enables the use of hot microelectrodes as detectors in HPLC or CE. In CE the improvement of the analytical signal at hot microelectrodes is smaller than in FIA and increase only 1.3–3.4 times. Heated microelectrodes were used for analysis of the flavonoids in natural samples of the plant (extract of sea buckthorn) and a pharmaceutical preparation (Cerutin).     

Enzymatic rotating biosensor for cysteine and glutathione determination in a FIA system

The high sensitivity that can be attained using an enzymatic system and mediated by catechols has been verified by on-line interfacing of a rotating biosensor and continuous flow/stopped-flow/continuous-flow processing. Horseradish peroxidase, HRP, [EC 1.11.1.7], immobilized on a rotating disk, in presence of hydrogen peroxide catalyzed the oxidation of catechols, whose back electrochemical reduction was detected on glassy carbon electrode surface at −150 mV. Thus, when l-cysteine (Cys) or glutathione (GSH) was added to the solution, these thiol-containing compounds participate in Michael addition reactions with catechols to form the corresponding thioquinone derivatives, decreasing the peak current obtained proportionally to the increase of its concentration. Cys was used as the model thiol-containing compound for the study. The highest response for Cys was obtained around pH 7. This method could be used to determine Cys concentration in the range 0.05-90 μM (r = 0.998) and GSH concentration in the range 0.04-90 μM (r = 0.999). The determination of Cys and GSH were possible with a limit of detection of 0.7 and 0.3 nM, respectively, in the processing of as many as 25 samples per hour. Current response of the HRP-rotating biosensor is not affected by the oxidized form of GSH and Cys (glutathione disulfide, GSSG, and l-cystine, respectively), by sulfur-containing and alkyl-amino compounds such as methionine and lysine, respectively. The interferences from easily oxidizable species such as ascorbic acid and uric acid are lowest.     

Determination of noradrenaline and dopamine in pharmaceutical injection samples by inhibition flow injection electrochemiluminescence of ruthenium complexes

Two maximal potential-resolved flow injection-electrochemiluminescent (FI-ECL) peaks were observed for Ru(bpy)₃²⁺/TPrA system at 0.90 and 1.05 V, and for Ru(phen)₃²⁺/TPrA at 1.01 and 1.25 V (vs. Ag/AgCl) in pH 8.0 phosphate buffer solutions. Sensitive ECL inhibition effects were observed in the presence of noradrenaline and dopamine for both of these systems. Therefore, an FI-ECL inhibition method for determination of noradrenaline and dopamine has been developed. Under optimal conditions, linear responses between logarithm of ECL intensity changes and logarithm of sample concentration were found for noradrenaline in the linear range (LR) of 4×10⁻⁸-1×10⁻⁵ mol l⁻¹ with theoretical detection limit (DL) of 2.5×10⁻⁸ mol l⁻¹ for Ru(bpy)₃²⁺/TPrA system, and in LR of 2×10⁻⁸-2×10⁻⁵ mol l⁻¹ with DL of 7.1×10⁻⁹ mol l⁻¹ for Ru(phen)₃²⁺/TPrA system; and for dopamine in LR of 8×10⁻⁸-2×10⁻⁵ mol l⁻¹ with DL of 5.2×10⁻⁸ mol l⁻¹ for Ru(bpy)₃²⁺/TPrA system, in LR of 4×10⁻⁸-2×10⁻⁵ mol l⁻¹ with DL of 1.5×10⁻⁸ mol l⁻¹ for Ru(phen)₃²⁺/TPrA system. It was applied for determination of commercial pharmaceutical injection samples with satisfied results. The mechanism of the inhibition effects was proposed in the preliminary way.     

Sequential flow injection analysis of ammonium and nitrate using gas phase molecular absorption spectrometry

A flow injection method on the basis of gas phase molecular absorption is described for the sequential determination of ammonium and nitrate. Two hundred microliters of sample solution is injected into the flow line. For ammonium determination, the sample zone is directed to a line in which reacts with NaOH (13 M) and produces ammonia. But for nitrate determination, the sample zone is passed through the on-line copperized zinc (Zn/Cu) reduction column and produces ammonium ion and in the follows ammonia. The produced ammonia in both cases is purged into the stream of N₂ carrier gas. The gaseous phase is separated from the liquid phase using a gas-liquid separator and then is swept into a flow through cell, which has been positioned in the cell compartment of an UV-Vis spectrophotometer. The absorbance of the gaseous phase is measured at 194 nm. Under selected conditions for sequential analysis of ammonium and nitrate, linear relations were found between the peak heights of absorption signals and concentrations of ammonium (10-650 μg ml⁻¹) and nitrate (20-800 μg ml⁻¹). The limit of detections for ammonium and nitrate analysis were 8 and 10 μg ml⁻¹, respectively. The relative standard deviations of repeated measurements of 50 μg ml⁻¹ of ammonium and nitrate were 2.0, 2.9%, respectively. Maximum sampling rate was about 40 samples/h. The method was applied to the determination of ammonium in pharmaceutical products and the sequential determination of ammonium and nitrate in spiked water samples.     

Design of a flow injection method for chlorophyll determination in in vitro plants

A flow injection (FIA) method was designed for the determination of chlorophylls a and b in small in vitro Dieffenbachia maculata “Sublime” plants. In the first step, the pigments from spinach leaves were separated, purified by solvent extraction and freeze–dried, to obtain standards for the FIA optimization. The sample extraction procedure was optimized. Four solvents were tested: diethyl ether, methanol, acetone and ethanol. The ethanol 96% was the optimal solvent for FIA purposes. It allows to the efficient extraction of the pigments and water can be used as carrier. The best FIA conditions found for the quasi-simultaneous quantification of chlorophylls a and b were a flow rate of 10.84 mL min⁻¹, a sample injection volume of 1.45 mL and a reactor length of 63 cm. The detection was performed with the automatic wavelength scanning Cintra 10e spectrometer, at 649 and 665 nm. The results obtained by the FIA method were compared to those obtained by the Arnon method. A deviation less than 5% was found between results for both methods. The concentration (mg g⁻¹) of chlorophylls a and b during three periods of the plants (in vitro, acclimatization, and adult) was determined to evaluate the whole in vitro procedure. It was found an increment of both pigment concentrations since the in vitro step till the adult stage, while the chlorophylls a to b ratio decreases. The designed method is suitable especially for the determination of the pigments at low concentrations in small samples with appropriate analytical quality.     

Spectrophotometric determination of mercury with 5,10,15,20-tetrakis(3-chloro-4-sulfophenyl)porphine by flow injection analysis

5,10,15,20-tetrakis(3-chloro-4-sulfophenyl)porphine (m-Cl-TPPS₄) was synthesized and used for the Spectrophotometric determination of mercury by flow injection analysis. A pseudo-first-order reaction kinetic mechanism was proposed with a rate constant of 0.8 min^–1 for Hg(II) withm-Cl-TPPS₄ in the presence of 8-hydroxyquinoline in a medium of 1.0M acetic acid and sodium acetate buffer solution (pH 6.22). In the optimum conditions of reaction temperature (85 ° C), stopped-flow time (60 s) and sampling volume (100 l), the method's relative standard deviation was 0.82% (n = 12) at 5.0 g ml^–1 mercury, with a linear range of 0–12.0 g ml^–1 and an analytical frequency of 60h^–1. The detection limit (3) was 0.025 g ml^–1. Interference studies showed that most metal ions co-existing with Hg²⁺ could be tolerated at 100-fold excess levels, but Zn²⁺, Cu²⁺ and Mn²⁺ needed to be masked. The method has been applied to the analysis of water samples with satisfactory results.     

Investigation of organic phase biosensor for measuring glucose in flow injection analysis system

The aim of our present work was to develop a flow-through measuring apparatus for the determination of glucose content as model system in organic media and to compare the properties of the biosensor in organic and in aqueous solutions. Glucose oxidase (GOx) enzyme was immobilized on a natural protein membrane in a thin-layer enzyme cell, made of Teflon. The enzyme cell was connected into a flow injection analyzer (FIA) system with an amperometric detector. After optimizing the system the optimal flow rate was found at 0.8 ml min⁻¹. In this case 50-60 samples were measured per hour. Adding ferrocene monocarboxylic acid (FMCA) to acetonitrile and to 2-propanol the optimal concentration was 5 mg l⁻¹, while in the case of tetrabutylammonium-p-toluenesulfonate (TBATS) the optima were 2.7 and 8.0 mg l⁻¹, respectively. With 6% buffer in acetonitrile containing FMCA more than 100 samples could be measured with the enzyme cell without any loss of activity. Measuring the hydrogen peroxide content produced in 2-propanol, the optimal concentration of buffer solution was at about 20%. The linear measuring range was 0-0.5 mM glucose in acetonitrile and 0-1.0 mM in 2-propanol.Glucose concentration of oily food samples was measured and compared with results obtained by the reference UV-photometric method. The correlation between the results measured by the two methods was very good with correlation coefficient (r) as high as 0.976.     

Use of microemulsions in flow injection analysis: spectrophotometric determination of copper

The use of microemulsions as media for liquid/liquid extraction is considered, with particular reference to the copper(II)/2,9-dimethyl-1,10-phenanthroline complex. Aqueous copper(II) standards covering the range 2.5 × 10^?5–7.5 × 10^?3 M were determined by a batch extraction procedure and by three flow-injection extraction procedures, one based on a pre-made water in oil microemulsion, one on a water in oil microemulsion formed on-line and one on an oil in water microemulsion.     

Simultaneous determination of Folpet and Metalaxyl in pesticide formulations by flow injection Fourier transform infrared spectrometry

Fourier transform infrared (FTIR) spectrometric methodology has been developed for the simultaneous determination of Folpet and Metalaxyl in pesticide formulations. The method involves the extraction of both active principles by sonication of the sample with CHCl₃ and direct measurement of the absorbance using peak height values at 1798 cm⁻¹ corrected with a baseline defined at 1810 cm⁻¹ for Folpet, and peak area data established from 1677 to 1667 cm⁻¹ corrected using a baseline from 1692 to 1628 cm⁻¹ for Metalaxyl. Limits of detection (3 s) values of 17 and 16 μg g⁻¹ were found for Folpet and Metalaxyl, respectively, with results comparable with those found by liquid chromatography with UV detection. The new method involves a considerable decrease in solvent consumption. The automation of the procedure by incorporating on-line dissolution and filtration of the samples allows complete mechanisation of the method and improves the safety of operation.     

FIA-Fluorimetric assembly for the determination of noradrenaline hydrochloride by a solid-phase reactor with immobilized hexacyanoferrate(III)

An FIA assembly provided with immobilized hexacyanoferrate(III) is proposed for the fluorimetric determination of noradrenaline hydrochloride. The oxidative reagent is immobilized by means of a strong anion-exchange resin. The FIA manifold is very simple and the calibration graph is linear over the range 0.5–75mgl^–1 noradrenaline hydrochloride with an r.s.d of 0.88% (17 replicates) and a sample throughput of 84h^–1. Foreign compounds such as NaCl, sucrose, lactose and sodium sulfate caused no significant errors. The procedure is applied to the determination of noradrenaline in a medicinal formulation.     

A compact flow injection analysis system for surface mapping of phosphate in marine waters

The design, construction and validation of a compact, portable flow injection analysis (FIA) instrument for underway analysis of phosphate in marine waters is described. This portable system employs gas pressure for reagent propulsion and computer controlled miniature solenoid valves for precise injection of multiple reagents into a flowing stream of filtered sample. A multi-reflection flow cell with a solid state LED photometer is used to detect filterable reactive phosphate (0.2 mum) as phosphomolybdenum blue. All the components are computer controlled using software developed using the Labviewtrade mark graphical programming language. The system has the capacity for sample throughput of up to 380 phosphate analyses per hour, but in the mode described here was operated at 225 analyses per hour. Under these conditions, the system exhibited a detection limit of 0.15 muM, reproducibility of 1.95 % RSD (n=9) and a linear response (r(2)=0.9992) when calibrated in the field with standards in the range 0.81-3.23 muM. The system was evaluated for the mapping of phosphate concentrations in Port Phillip Bay, south eastern Australia, and during the course of a 150 km cruise, 542 analyses were performed automatically. In general, good agreement was observed between analyses obtained using the portable FIA system and those obtained from manual sampling and laboratory analysis.     

Hollow fiber-based liquid-liquid-liquid microextraction followed by flow injection analysis using column-less HPLC for the determination of phenazopyridine in plasma and urine

Hollow fiber-based liquid-liquid-liquid microextraction (HF-LLLME) followed by flow injection analysis and diode array detection (FIA-DAD) was applied as a simple and sensitive quantitative method for the determination of phenazopyridine in urine and plasma samples. Flow injection system included a conventional HPLC system (without a chromatographic column) and a diode array detector. The extraction of phenazopyridine was carried out using diphenyl ether as the organic phase for filling the pores of the hollow fiber wall, and 0.1 M H(2)SO(4) solution as acceptor phase in the lumen of the fiber. The factors affecting the HF-LLLME and flow injection analysis including type of organic solvent, pH of donor phase, extraction temperature, extraction time, stirring rate, and pH of mobile phase were investigated and the optimal extraction conditions were established. With the consumption of 5 mL of sample solution, the enrichment factor was about 230. The limit of detection was 0.5 μg/L with inter- and intra-day precision being (RSD%) 6.9 and 4.9, respectively. Excellent linearity was found between 5 and 200 μg/L.     

Determination of sulfite in water samples by flow injection analysis with fluorescence detection

<正>A fast,sensitive,and reliable method for the determination of sulfite(SO_3~(2-)) in fresh water and seawater samples was developed.The proposed method was based on the reaction of o-phthalaldehyde(OPA)-sulfite-NH_3 in alkaline solution,with flow injection analysis and fluorescence detection.The experimental parameters were investigated in pure water and seawater matrixes. The detection limits(S/N = 3) were 0.006μmol/L in pure water and 0.018μmol/L in seawater for SO_3~(2-).The method was successfully applied to analyze SO_3~(2-) in the samples of rain water and flue gas desulfurization seawater.