Chiral separation with gradient elution isotachophoresis for future in situ extraterrestrial analysis

The first results of chiral separations with the gradient elution isotachophoresis method are presented. As previously described, citrate is used in the run buffer as the leading ion and borate in the sample buffer as the terminating ion. Modulation of parameters such as electrolyte pH, pressure scan rate, chiral selector concentration, combinations of CD or the percentage of ampholytes provides an easy optimization of the separations. To perform fluorescent detection 5-carboxyfluorescein succinimidyl ester and two fluorogenic-labeling agents, fluorescamine (Fluram) and 3-(4-carboxybenzoyl)quinoline-2-carboxaldehyde, are used to label amino acids. With the 5-carboxyfluorescein amino acids, chiral separations are easily obtained using a neutral CD ((2-hydroxypropyl)-beta-CD) at a low concentration (2 mmol/L). With Fluram amino acids, the situation is more complicated due to the formation of diastereoisomers and due to weak interactions with the different CDs used. The use of the 3-(4-carboxybenzoyl)quinoline-2-carboxaldehyde-labeling agent solves the problems observed with the Fluram agent while retaining the fluorogenic properties. These first results demonstrate the simplicity and the feasibility of gradient elution isotachophoresis for chiral separations.     

Precolumn diastereomerization and micellar electrokinetic chromatography on a plastic microchip: rapid chiral analysis of amino acids

Precolumn derivatization and chiral separation of DL-amino acids based on diastereomerization have been performed on an integrated poly(dimethylsiloxane) microchip. Diastereomeric derivatives were formed in a microfabricated precolumn reactor by the reaction of amino acid enantiomers with o-phthaldialdehyde/2,3,4,6-tetra-O-acetyl-1-thio-beta-D-glucopyranose (OPA/TATG), and separated by MEKC in an achiral environment without chiral selectors in the running buffer. Optimized precolumn reactions and chiral separations of amino acids were achieved within 2.5 min. Resolutions of diastereomers of OPA/TATG-amino acids were in the range of 2.5-6.1 at optimized separation conditions. Simultaneous separation of a mixture of five chiral amino acids was successfully performed in a single run in less than 100 s.     

Analytical potential of 6-oxy-(N-succinimidyl acetate)-9-(2'-methoxycarbonyl) fluorescein for the determination of amino compounds by capillary electrophoresis with laser-induced fluorescence detection

The analytical potential of a fluorescein analogue, 6-oxy-(N-succinimidyl acetate)-9-(2'-methoxycarbonyl) fluorescein (SAMF), for the first time synthesized in our laboratory, as a labeling reagent for the labeling and determination of amino compounds by capillary electrophoresis (CE) with laser-induced fluorescence (LIF) detection was investigated. Biogenic monoamines and amino acids were chosen as model analytes to evaluate the analytical possibilities of this approach. The derivatization conditions and separation parameters for the biogenic amines were optimized in detail. The derivatization was performed at 30 degrees C for 6 min in boric acid buffer (pH 8.0). The derivatives were baseline-separated in 15 min with 25 mM boric acid running buffer (pH 9.0), containing 24 mM SDS and 12.5% v/v acetonitrile. The concentration detection limit for biogenic amines reaches 8 x 10(-11) mol.L(-1) (signal-to-noise ratio = 3). The application of CE in the analysis of the SAMF-derivatized amino acids was also exploited. The optimal running buffer for amino acids suggested that weak acidic background electrolyte offered better separation than the basic one. The proposed method was applied to the determination of biogenic amines in three different beer samples with satisfying recoveries varying from 92.8% to 104.8%. Finally, comparison of several fluorescein-based probes for amino compounds was discussed. With good labeling reaction, excellent photostability, pH-independent fluorescence (pH 4-9), and the resultant widely suited running buffer pH, SAMF has a great prospect in the determination of amino compounds in CE.     

High-speed chiral separations on microchip electrophoresis devices

High-speed electrophoretic chiral separations have been successfully performed in a microfabricated device by employing cyclodextrin-modified micellar electrokinetic chromatography (CD-MEKC). Utilizing short separation channels and relatively high field strengths in combination with small volume-defined injection plugs, and operating in counter-electroosmotic flow conditions, fast and efficient separations of fluorescein insothiocyanate (FITC)-labeled amino acid enantiomers were obtained. Analysis time ranged from 75 s for the most basic amino acids to 160 s for the most acidic ones with associated efficiencies from 7000 up to 28 000 effective plates (100 000 to 395 000 plates/m). Buffer parameters were varied in order to study the effect on chiral resolution. A buffer system consisting of 100 mM borate (pH 9.4), 30 mM of SDS, and 10 mM gamma-CD as chiral selector provided adequate resolution of the majority of FITC-amino acid enantiomers tested.     

On-column labeling technique and chiral CE of amino acids with mixed chiral selectors and UV detection

A novel method has been developed for the on-column labeling of amino acid enantiomers with 9-fluoroenylmethyl chloroformate (FMOC), followed by chiral CE with a binary chiral selector system and UV detection. Efficient labeling was achieved by sequential injection of amino acids, borate buffer, and FMOC labeling solution at 0.2 psi for 6 s. After injection, the sandwich sections were electrically mixed at 250 V/cm for 6 s and allowed to react (electric field-free) at room temperature for 2 min. With this procedure, successful online-labeling and chiral CE separation of 19 pairs of amino acids (AA) have been conducted, giving 17 pairs fully enantioresolved (R(s) = 1.73-5.79) and two pairs partially resolved (Ala, R(s) = 0.39 and Arg, R(s) = 1.15) using a running buffer of 150 mM borate containing 30 mM beta-CD, 30 mM sodium taurodeoxycholate (STDC), and 15% isopropanol (IPA) at pH 9.0. Chiral CE of some mixed pairs was also demonstrated, much the same as using precolumn labeling. Surprisingly, Met, Asp, Asn, Gln, and His gained even higher enantioresolution (up to 2.5%) compared with the case of precolumn labeling. As validated by both artificially prepared solutions and serum samples, the method was applicable to the quantitative determination of AA, with LODs down to 4.0 microM. The method allowed the determination of D-AA at the ratio of 1:100 (D:L).     

Chiral separation of halogenated amino acids by ligand-exchange capillary electrophoresis

The chiral separation of halogenated amino acids by ligand-exchange CE is described. Halogenated amino acids attracted increasing interest in recent years because of their physiological activities. Different chiral selectors, as there are L-4-hydroxyproline, L-histidine, and N-alkyl derivatives of L-4-hydroxyproline in form of their copper(II) complexes, are compared for their chiral recognition ability for halogenated amino acids. The influence of various parameters, such as selector concentration, pH, organic modifier, and field strength, on the resolution was investigated. All halogenated amino acids investigated were baseline-separated under optimized conditions.     

Chiral determination of amino acids by capillary electrophoresis and laser-induced fluorescence at picomolar concentrations

In this publication we present results on the determination of enantiomers of amino acids at very low concentrations. A fluoresceine-based chiral dye was synthesized to allow the separation of diastereoisomers of D- and L-amino acids. We used capillary electrophoresis with different non-ionic surfactants (Brij). The separation parameters were optimized and separations of D- and L-isovaline, an unusual terrestrial amino acid, were obtained. The sensitivity limits were also determined using a commercial laser-induced fluorescence detector. The quantitation of these amino acids is very important to understand the process of chiral selection on Earth.     

Direct UV detection of underivatized amino acids using capillary electrophoresis with online sweeping enrichment

This is an original report proposed a CE method for direct analysis of the underivatized amino acids using UV detection with relatively higher sensitivity, which was based on coordination interactions between amino acids and Cu (II) ions. In addition, an online sweeping preconcentration technique was easily combined to improve the detection sensitivity. Satisfying separations of the amino acids were obtained under optimized conditions: 50 mmol/L CuSO₄–0.05% HAc–H₂O (pH 4.5), and the separation voltage of 15 kV. The LODs for the analytes ranged from 0.1 to 0.5 μmol/L. The linearity of detection for all analytes was two orders of magnitude with the correlation coefficients greater than 0.99. The repeatability was displayed with an RSD less than 3% for migration time and peak height (n = 5). Moreover, some amino acids in real samples of human saliva and green tea were analyzed by this direct UV detection CE method with acceptable sensitivity.     

Synthesis and application of dehydroabietylisothiocyante as a new chiral derivatizing agent for the enantiomeric separation of chiral compounds by capillary electrophoretic

A new chiral derivatizing reagent, dehydroabietylisothiocyante (DHAIC), was synthesized and used for the enantiomeric separation of chiral compounds in capillary electrophoresis (CE). The synthetic route to obtain DHAIC is described. The separation conditions for the chiral separation of several chiral compounds, such as protein amino acids and chiral drug DOPA were optimized. Best results for the chiral separation of DHAIC derivatized amino acids and DOPA were obtained in a running buffer consisted of 50 mM borate (pH 9.5), 5 mM sodium dodecyl sulphate (SDS) and 20% acetonitrile for amino acids and 60 mM Na₂HPO₄ (pH 8.0), 17 mM SDS and 25% acetonitrile for DOPA. Under the conditions studied, chiral separation of five amino acids including Ser, Val, Ala, Thr, Cys and a chiral drug DOPA as their diastereomeric DHAIC derivatives has been achieved by micellar electrokinetic chromatography (MEKC).     

Chiral separation of amino acids by capillary electrophoresis with 3-[(3-cholamidopropyl)-dimethylammonio]-1-propane sulfonate as chiral selector

Summary 3-[(3-cholamidopropyl)-dimethylammoniol-1-propane sulfonate (CHAPS) can be used as an effective chiral selector for the separation of dansyl-amino acids by capillary electrophoresis (CE). While CHAPS can serve as an chiral selector, better enantiomeric separation can be performed by using CHAPS not as the sole chiral selector but as one of a [CHAPS-SDS-cyclodextrin] three-component system. In this CHAPS-SDS-CD system, enantiomeric separations of the amino acids can be readily accomplished by judiciously adjusting the pH of the solution, concentrations of CHAPS and SDS, and the concentration and type of CD. All amino acids can be baseline resolved in less than 15 minutes with resolution as high as 2.01 at pH 6.5 with 50 mM of CHAPS and 75 mM of SDS. The resolution is also dependent on the size of the CD. Substantial increase in the resolution can be readily achieved by replacing β-CD with γ-CD. For example, theR _s for Leu was increased by four-folds (from 1.65 to 6.29) while the elution time still remains as short as 20 min when β-CD was replaced by γ-CD.     

毛细管电泳法手性拆分14种二肽

以咔唑-9-乙基氯甲酸酯(CEOC)作为柱前衍生试剂,采用毛细管电泳对14种二肽进行了手性拆分。以5种二肽为代表,考察了缓冲液种类、浓度、pH值、二元手性选择剂的组合配比等因素对二肽的拆分效果,优化了实验条件。在各自的优化条件下,14种二肽手性拆分的分离度均在3.63以上,最高分离度可达43.14(Gly-Ala)。     

Enantioseparation of dansyl amino acids by ligand‐exchange capillary electrophoresis with zinc(II)‐L‐phenylalaninamide complex

A novel method of chiral ligand‐exchange CE was developed with L ‐amino acylamides as a chiral ligand and zinc(II) as a central ion. It has been demonstrated that these chiral complexes, such as Zn(II)‐L ‐alaninamide, Zn(II)‐L ‐prolinamide, and Zn(II)‐L ‐phenylalaninamide, are suitable for use as chiral selectors for the enantioseparation of either individual pair of or mixed dansyl amino acids. The optimal separation running buffer consisted of 5 mM ammonium acetate, 100 mM boric acid, 4 mM ZnSO₄·7 H₂O, and 8 mM L ‐amino acylamides at pH 8.2. The experiments showed that apart from the effect of the concentration of the complexes on the resolution and the migration time, the buffer pH also had a sharp influence on resolution. The employed chiral ligands exhibited different enantioselectivities and enantiomer migration orders. D ‐Amino acids migrate faster than L ‐amino acids when Zn(II)‐L ‐alaninamide and Zn(II)‐L ‐phenylalaninamide are used as chiral selectors, but it was observed that the migration order is reversed when Zn(II)‐L ‐prolinamide is used as the chiral selector. Furthermore, the amount of dansylated amino acids is found to be highly dependent on the labeling temperature.     

Enantiomeric separation of hydroxy acids and carboxylic acids by diamino-beta-cyclodextrins (AB,AC,AD) in capillary electrophoresis

Selectively modified 6,6'-dideoxy-6,6'-L-diamino-beta-cyclodextrins (AB, AC, AD) were successfully used as chiral selectors for the enantiomeric separation of hydroxy acids and carboxylic acids (in particular, phenoxyalkanoic acid herbicides) in capillary electrophoresis (CE). Chiral separations were obtained at a low selector concentration (1 mM) with good enantioselectivity and resolution factors. Separations were optimized as a function of pH. The different position of the charged groups on the upper rim greatly influenced the separation, accounting for electrostatic interactions between the protonated amino groups of the cyclodextrins (CDs) and the carboxylate of the selectands. The best enantiomeric separation of hydroxy acids was obtained with the AC regioisomer, whereas carboxylic acids were well resolved only by the AB regioisomer. A recognition model is proposed, based on two-dimensional nuclear magnetic resonance (2-D NMR) experiments, in which the orientation of the guest in the inclusion complex is determined by the electrostatic interactions between the selectand and the CD upper rim.     

毛细管电动色谱带电环糊精拆分N-FMOC氨基酸对映体

 将负电性磺丁基 -β -环糊精手性添加剂应用于毛细管电泳氨基酸对映体的拆分研究中 ,对 8种氨基酸对映体与 9-芴甲基氧基甲酰氯 (FMOC-Cl)生成的衍生物进行了分离 ,其中 5种得到了基线分离。考察了背景电解质 p H值及磺丁基 -β -环糊精的浓度对 N-FMOC氨基酸对映体拆分的影响。     

Enantiomeric separation of chiral peptide nucleic acid monomers by capillary electrophoresis with charged cyclodextrins

Direct chiral separation of chiral peptide nucleic acid (PNA) monomers has been achieved for the first time by capillary electrophoresis (CE) with charged cyclodextrins as chiral selectors added to the electrophoretic buffer. Selectively modified 6-deoxy-6-N-histamino-beta-cyclodextrin and sulfobutyl ether-beta-CD were successfully used as chiral selectors for the enantiomeric separation of chiral monomers based on different aminoethylamino acids bearing thymine or adenine as nucleobases. Chiral separations were obtained at low selector concentrations (1-3 mM) with good enantioselectivity and resolution factors. Separations were optimized as a function of pH in order to exploit the effect of the electrostatic interactions between the oppositely charged selector and selectand. The method has been applied to the analysis of the enantiomeric excess of chiral monomers used for the solid phase synthesis of chiral PNA oligomers. CE chiral analysis showed that a very high enantiomeric purity was generally achieved in the synthesis of all monomers, except for histidine and aspartic acid based monomers in which ca. 10% of the "wrong" enantiomer was always present.     

Comparison of enantioseparation of amino acid derivatives in aqueous and mixed aqueous-organic media by capillary zone electrophoresis

The chiral separation of dansyl-amino acids has been performed by capillary zone electrophoresis using ¶β-cyclodextrin as a chiral selector, urea as an additive and 2-propanol and methanol as organic modifiers. The enantiomeric separations of dansyl-amino acids were investigated in aqueous medium and compared with the separation in mixed aqueous-organic medium as background electrolytes. The separation conditions, (concentration of buffer, β-cyclodextrin, methanol, urea and the pH value of buffer) were optimized. In the absence of organic modifier, only five pairs of 8 separated dansyl-amino acids were resolved when run separately. A mixture of up to eight chiral amino acids can be baseline resolved in less than 19 min by β-cyclodextrin-modified capillary zone electrophoresis with a buffer of 60 mmol L^–1 H₃BO₃-KCl/40 mmol L^–1 NaOH (pH 9.0), 4 mol L^–1 urea, 100 mmol L^–1β-cyclodextrin and 10% (v/v) methanol.     

Recent developments in chiral capillary electrophoresis and applications of this technique to pharmaceutical and biomedical analysis

This paper provides an overview of the current status of chiral capillary electrophoresis (CE). The emphasis is placed on the application of CE in chiral separation of various racemic compounds. During the last two years about 280 papers, several review articles, and two entire issues, edited by S. Fanali (Electrophoresis 1999, 20, 2577-2798, and H. Nishi and S. Terabe (J. Chromatogr. A 2000, 879, 1-471.) have been devoted to chiral CE. Enantiomeric separations of various compounds, e.g., pharmaceuticals, drug candidates, drugs and related metabolites in biological fluids, amino acids, di- and tri peptides, pesticides and fungicides, have been performed using different chiral selectors. Native and derivatized cyclodextrins continue to be the most widely used chiral selectors. Other chiral selectors such as natural and synthetic chiral micelles, crown ethers, chiral ligands, proteins, oligo- and polysaccharides, and macrocyclic antibiotics have also been applied to chiral CE separations.     

Low-molecular-weight chiral cation exchangers: novel chiral stationary phases and their application for enantioseparation of chiral bases by nonaqueous capillary electrochromatography

Cation exchange type chiral stationary phases (CSPs) based on 3,5-dichlorobenzoyl amino acid and amino phosphonic acid derivatives as chiral selectors (SOs) and silica as chromatographic support were developed and applied to enantiomer separations of chiral bases by nonaqueous capillary electrochromatography (NA-CEC). As a rationale for efficient CSP development we adopted the combined use of the "reciprocity principle of chiral recognition" and nonaqueous ion-pair CE as screening assay. Thus, (S)-atenolol was employed as chiral counter-ion added to the BGE in CE and a series of N-derivatized amino acids and amino phosphonic acids were screened to derive reciprocally information on their chiral recognition abilities for atenolol enantiomers. Two SO candidates, namely N-(3,5-dichlorobenzoyl)-O-allyl-tyrosine and N-(4-allyloxy-3,5-dichlorobenzoyl)-1-amino-3-methylbutane phosphonic acid that have been identified as potential SOs in the CE screening were, after immobilization on thiol-modified silica, evaluated in cation-exchange NA-CEC. The strong chiral cation exchanger with the free phosphonic acid group exhibited enhanced enantioselectivity compared to the weak chiral cation exchanger with the carboxylic acid group. A wide variety of chiral bases could be successfully resolved on the strong chiral cation exchanger with alpha-values up to 2.2 and efficiencies up to 375000 m-1 including beta-blockers and other amino alcohols, local anesthetics like etidocaine, antimalarial agents like mefloquine, Tr?ger's base, phenothiazines like promethazine, and antihistaminics. The influence of several experimental parameters (electrolyte concentration, acid-base ratio and acetonitrile-methanol ratio) was evaluated.     

New triazine spectroscopic reagent for the separation of DL-amino acids by micellar electrokinetic chromatography

An approach to the chiral separation of racemic mixtures of amino acids by means of micellar electrokinetic chromatography after derivatization with a new triazine spectroscopic reagent, 3-(4,6-dichloro-1,3,5-triazinylamino)-7-dimethylamino-2-methylphenazine (DTDP), has been evaluated. It was found that the derivatives of the aliphatic amino acids such as serine, valine and arginine, could produce a strong UV absorption at 282 nm, whose apparent molar absorptivities are of 10(-4) M(-1) cm(-1), and thus the concentration of the amino acids down to 3 x 10(-7) M can still give a detectable signal (S/N = 3). Beta-Cyclodextrin (beta-CD) added to the buffer system was used as a chiral selector, and separation conditions were optimized. The presence of an organic modifier (2-propanol) was also a prerequisite for the chiral separation. The best results for the chiral separation of DTDP-amino acids were achieved in a mixed sodium dodecylsulfate-beta-CD-borate-2-propanol medium at pH 9.0. Compared to some of the commonly used derivatization methods, the present one offers a relatively stable derivative and strong UV absorption for the spectroscopically inert amino acids, thus enabling amino acids to be separated and detected by CE even with a simpler UV detector.     

Enantiomeric Separations in Capillary Electrophoresis Using 18-Crown-6-tetracarboxylic Acid (18C6H4) as Buffer Additive

An overview is presented of the applicability of the crown ether 18-crown-6-tetracarboxylic acid (18C6H₄) as buffer additive in capillary electrophoresis (CE) for the separation of enantiomers. The chiral selector 18C6H₄ is particularly useful for the separation of racemates having a primary amino function. Unfortunately, the crown ether is no longer commercially available. The synthesis and spectroscopic characterization are therefore described in detail. Moreover, a method is presented for the regeneration of the crown ether after CE application. Some new enantiomeric separations of amino acids i.e. NORLEU, ARG, GLU, m-TYR, and o-TYR are listed and the influence of the pH and temperature of the separation buffer is discussed. An intermediate in the synthetic pathway, namely 18-crown-6-tetracarboxamide, did not exhibit any enantioselectivity in CE.