The effect of activated fillers on the properties of styrene–acrylic adhesives

Results of kaolin modification by thermal activation, sonication and 3% solution of acetic acid are considered. It is shown that the introduction of thermally activated kaolin to compositions based on styrene–acrylic filming agents increases the adhesion characteristics by 1.25–1.4 times (for steel and cement–sand surfaces) and cohesive strength by 1.5–2 times.     

Solvent effects on the steady state photophysics of estrone and 17β-estradiol

Absorption and emission yields for estrone and 17β-estradiol were measured in a variety of room temperature solvents. Molar extinction coefficients were found to not vary as a function of solvent, while fluorescence yields were found to be significantly affected by the polarity and hydrogen-bond accepting ability of the solvent, with the yield for 17β-estradiol being highest in nonpolar, hydrogen-bond donating solvents, and lowest in the nonpolar, hydrogen-bond accepting solvent ethyl acetate. Estrone's emission yield was found to be a factor of ten smaller than 17β-estradiol's. Strong solvent and excitation wavelength dependences were found for the relative amounts of emission between estrone's two emission bands, with increased relative emission occurring in nonpolar aprotic solvents, and under higher excitation energies. These results are interpreted with the aid of vertical excitation energies from time-dependent density functional calculations using both explicit and implicit solvation models.     

Separation of dansylated 17β-estradiol, 17α-estradiol, and estrone on a single HPLC column for simultaneous quantitation by LC–MS/MS

We show here that baseline separation of dansylated estrone, 17β-estradiol, and 17α-estradiol can be done, contrary to previous reports, within a short run time on a single RP-LC analytical column packed with particles bonded with phenyl-hexyl stationary phase. The chromatographic method coupled with isotope dilution tandem MS offers a simple assay enabling the simultaneous analysis of these analytes. The method employs ¹³C-labeled estrogens as internal standards to eliminate potential matrix effects arising from the use of deuterated estrogens. The assay also offers adequate accuracy and sensitivity to be useful for biological samples. The practical applicability of the validated method is demonstrated by the quantitative analyses of in vivo samples obtained from rats treated with Premarin®.

Molecular recognition of endocrine disruptors by synthetic and natural 17β-estradiol receptors: a comparative study

A β-estradiol receptor binding mimic was synthesised using molecular imprinting. Bulk polymers and spherical polymer nanoparticles based on methacrylic acid and ethylene glycol dimethacrylate as the functional monomer and crosslinker, respectively, were prepared in acetonitrile. The selectivity was evaluated by radioligand binding assays. The imprinted polymers were very specific to β-estradiol since the control polymers bound virtually none of the radioligand. The bulk polymer was then employed to screen endocrine disrupting chemicals. Structurally related steroids like α-estradiol, estrone and ethynylestradiol showed, respectively, 14.0, 5.0 and 0.7% of relative binding to the β-estradiol polymer, whereas most unrelated chemicals did not bind at all. These results are compared to those obtained with a bioassay using stably transfected yeast cells in culture bearing the human estrogen receptor. The receptor was activated by several estrogen-like chemicals and to a lesser extent by some structurally related chemicals. Figure A molecularly imprinted polymer that was a synthetic receptor for beta-estradiol was used for the screening of endocrine disrupting chemicals that are structurally related or unrelated to beta-estradiol. The results were compared with the recognition of the compounds by the biological estrogen receptor expressed in yeast cells. Related steroids like alpha-estradiol, estrone and ethynylestradiol showed significant binding to the beta-estradiol imprinted polymer, whereas most unrelated chemicals did not bind. The biological receptor was activated by several estrogen-like chemicals, and to a lesser extent by some structurally related chemicals     

The effect of inclusion inβ-cyclodextrin on the chemistry of peroxides: Reactions of radicals withβ-cyclodextrin

Studies by electron paramagnetic resonance (EPR), differential scanning calorimetry, thermogravimetric analysis, HPLC and NMR showed that radicals produced by thermolysis and photolysis of benzoyl peroxide,t-butyl peroxide and cumene hydroperoxide included in-cyclodextrin (-CD), undergo significant reaction with the-CD. The formation of-CD radicals was observed by EPR. Products formed by addition of radicals to-CD were also observed. Such host:guest radical reactions explain the reported stabilization of peroxides, found with-CD inclusion, as being primarily due to the interruption of chain reactions by trapping of the chain carriers. A small increase in activation barrier for cleavage of the included peroxide in-CD was also observed.     

Synthesis of tin oxide nanoparticles by sol–gel process: effect of solvents on the optical properties

Tin oxide (SnO₂) nanoparticles were synthesized by the reaction of SnCl₄·5H₂O in methanol, ethanol and water via sol–gel method. The samples were characterized by X-ray diffraction (XRD), Fourier transform infrared, Scanning electron microscopy and Transmission electron microscopy. The optical properties of the as-prepared samples were investigated. The XRD analysis showed well crystallized tetragonal SnO₂ can be obtained and the crystal sizes were 3.9, 4.5 and 5 nm for the sample calcined at 400 °C for 2 h. It was found that solvents played important roles in the particle size effect of nanocrystalline SnO₂.     

The effect of temperature on the formation of titanium dioxide structures on γ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> surface

The effect of calcination temperature of hydrated gamma-aluminum oxide on the phase formation of surface structures and the content of titanium in them in the course of successive treatment of the initial matrix with TiCl₄ and H₂O was determined.     

Adsorptive characteristics of isoniazid on powdered activated carbon: π–π Dispersion interactions at the solid–solution interface

The presence of antibiotic residues in the aquatic environment poses a potential risk to living organisms due to the development of antibiotic resistance in bacteria. In the present study, the removal of isoniazid by commercial powdered activated carbon was studied in aqueous solutions. The adsorption experiments were done as a function of time, concentration, temperature, and pH in order to understand the adsorption mechanism. The Langmuir and the Freundlich isotherms were used to model the equilibrium data. The results showed that isoniazid was physisorbed on the surface of the activated carbon by π–π dispersion interactions.     

Enhanced degradation of 17β-estradiol by AgI/N-Bi2O3 composite: strong synergy of adsorption–photocatalysis

Research on Chemical Intermediates - 17β-estradiol (E2) is one of the environmental endocrine disruptors threatening human health. In this paper, AgI/N-Bi2O3 composites with the different mass...     

The effect of polymerization conditions on crystalline of polybutene-1 catalyzed by metallocene catalyst

Polybutene-1 was synthesized stereoselectively with the precursorη5-(pentamethyl-cyclopentadienyl) tribenzyloxide titanium (Cp*Ti(OBz)3) and methylaluminoxane (MAO). The effects of polymerization conditions, trimethyl alumina (TMA) content in MAO and temperature on the crystalline and molecular weight of the products, and catalytic activity were investigated. The structural properties of the polybutene-1 were characterized with 13C NMR and WAXD.     

Removal of bisphenol A via a hybrid process combining oxidation on β-MnO2 nanowires with microfiltration

A novel hybrid process combining β-MnO₂ nanowires oxidation and microfiltration was adopted to remove bisphenol A (BPA), an endocrine disrupting chemical (EDC) in the aquatic environment. The β-MnO₂ nanowires synthesized via a facile hydrothermal method were characterized by X-ray diffraction, transmission electron microscopy, field-emission scanning electron microscope, and nitrogen sorption. It was demonstrated that β-MnO₂ nanowires can degrade BPA effectively. Investigation on operation parameters indicated that oxidation of BPA using β-MnO₂ nanowires was evidently dependent on pH, while humic acid and coexisting metal ions such as Ca²⁺, Mg²⁺, and Mn²⁺ induced suppressive effects. After oxidation, a crossflow microfiltration process was conducted to efficiently separate and recover the β-MnO₂ nanowires from treated water. Membrane fouling study showed that the as-synthesized β-MnO₂ nanowires possess excellent mechanical stability and was able to retain the 1D structure with high aspect ratios after reaction, thus significantly reducing membrane pore blocking in the microfiltration process.     

The promotion effect of oxygen on the dissociative adsorption of water to uranium dioxide surface: a GGA + U study

Journal of Radioanalytical and Nuclear Chemistry - The promotion effect of O2 on the dissociative adsorption of H2O&nbsp;to&nbsp;UO2 surface is studied by first-principles method within...     

Investigating the mechanisms of 17<Emphasis Type="Italic">β</Emphasis>-estradiol imprinting by computational prediction and spectroscopic analysis

Molecular dynamics simulations combined with spectroscopic analysis were applied to understand the nature of recognition in molecularly imprinted polymers (MIPs), and for optimizing the MIP formulation. The best monomers for synthesizing imprinted materials for 17β-estradiol (BE2) were selected by evaluating the strength of the template–monomer interaction derived from molecular dynamics simulations. A number of potential functional monomers for BE2 were screened for hydrogen-bonding strength in order to analyze template–monomer interactions favorable for synthesizing noncovalent MIPs, with the simulations revealing that methacrylic acid, 2-(diethylamino)ethyl methacrylate, and methacrylamide provided the highest binding affinity to BE2. These theoretical predictions agree with previously reported results on batch rebinding studies using the corresponding functional monomers for synthesizing a series of MIPs. Molecular analysis such as ¹H NMR was used for experimentally confirming the prevalent template–monomer interactions derived from the modeling results. Molecular dynamics simulations indicating monomer dimerization in the prepolymerization solution correlated with the nature of the porogenic solvent, which was confirmed by NMR studies on hydrogen-bonding interactions of methacrylic acid in different solvents. Furthermore, batch rebinding studies revealed that the specific functionalities of the monomers essential to rebinding are retained after polymerization, which proves that the application of computational methods for modeling the prepolymerization solution provides useful information for optimizing real MIP systems.     

The protection effect of β-CD on DNA damage induced by ultrafine TiO2

Under the photocatalysis of 365 nm ultraviolet radiation, ultrafine TiO2 caused the oxidative damage of Teasy plasmid DNA. The damage was determined by gel-electrophoresis. Then, a different dose of β-CD was added to the reaction, and the damage was restrained. The rate of damage restraining reached 97% when the mass of β-CD was 4 times as that of TiO2. Through UV scan and IR spectroscopy, it was found that the Ti-O of ultrafine TiO2 was bound with -OH of β-CD cavum and the -OH on the surface of ultrafine TiO2 disappeared, so the formation of · OH was controlled. The ultrafine TiO2 has been widely used, but it was determined to be carcinogenic by some research. The protection effect of β-CD to DNA in the molecular level takes a new look on the surface modification of nano particles to decrease the toxic effect.     

The protection effect of β-CD on DNA damage induced by ultrafine TiO_2

Under the photocatalysis of 365 nm ultraviolet radiation,ultrafine TiO2 caused the oxidative damage of Teasy plasmid DNA. The damage was determined by gel-electrophoresis. Then,a different dose of β-CD was added to the reaction,and the damage was restrained. The rate of damage restraining reached 97% when the mass of β-CD was 4 times as that of TiO2. Through UV scan and IR spectroscopy,it was found that the Ti-O of ultrafine TiO2 was bound with -OH of β-CD cavum and the -OH on the surface of ultrafine TiO2 disappeared,so the formation of ?OH was controlled. The ultrafine TiO2 has been widely used,but it was determined to be carcinogenic by some research. The protection effect of β-CD to DNA in the molecular level takes a new look on the surface modification of nano particles to decrease the toxic effect.     

Mass transfer effect on corrosion inhibition process of copper–nickel alloy in hydrochloric acid by Benzotriazole

The corrosion inhibition of copper–nickel alloy by Benzotriazole (BTA) in 1.5 M HCl has been investigated by weight loss and polarization techniques at different temperatures. Maximum value of inhibitor efficiency was 99.8% for BTA at 35 °C and 0.1 M inhibitor concentration, while the lower value was 86.8% at 55 °C and 0.02 M inhibitor concentration. The non-linear region of the polarization curve near the corrosion potential can be discussed depending on data of over potential as a function of current densities. These data can be analyzed by suggestion of a mathematical model to take into account the effect of mass transfer on activation process.     

The effect of 2-hydroxypropyl-β-cyclodextrin on the excited triplet state of promazine and chlorpromazine

Chlorpromazine hydrochloride (CPZ) is a widely used anti-psychotic drug that induces skin photosensitization and photoallergy response after systematic use or topical applications. The photoallergic mechanism is still unknown. However, it has been proposed that the triplet excited state (³CPZ*) could participate in the photodamaging effects. In this work, we report the photophysical properties of the triplet excited state of CPZ and its parent derivative promazine hydrochloride (PZ) in the presence of 2-hydroxypropyl-β-cyclodextrin (HPC). Absorption measurements indicate that PZ and CPZ form an inclusion complex with HPC through a 1:1 stoichiometry. The equilibrium constant at 25 °C is (2.55 ± 0.09) × 10³ M⁻¹ and (3.27 ± 0.07) × 10³ M⁻¹ for PZ and CPZ, respectively. The CPZ and PZ triplet excited state properties changed in the presence of HPC. The triplet lifetime increases with HPC concentration that is related to the amount of drug bound. In addition, the triplet intersystem crossing quantum yield was determined to be 0.45 and 0.17 for PZ and CPZ, respectively, when more than 95% of the drug molecules are bound to HPC. Altogether, these results suggest that the microenvironment plays a crucial role in the ³CPZ* and ³PZ* properties and thus it can modulate their photosensitizing effects.     

The effect of hydrogen reduction of α-MnO2 on formaldehyde oxidation: The roles of oxygen vacancies

A series of α-MnO₂ catalysts with various Mn valence states were treated by hydrogen reduction for different periods of time. Their catalytic capacity for formaldehyde (HCHO) oxidation was evaluated. The results indicated that hydrogen reduction dramatically improves the catalytic performance of α-MnO₂ in HCHO oxidation. The α-MnO₂ sample reduced by hydrogen for 2 h possessed superior activity and could completely oxidize 150 ppm HCHO to CO₂ and H₂O at 70 °C. Multiple characterization results illustrated that hydrogen reduction contributed to the production of more oxygen vacancies. The oxygen vacancies on the catalyst surface enhanced the adsorption, activation and mobility of O₂ molecules, and thereby enhanced HCHO catalytic oxidation. This study provides novel insight into the design of outstanding MnO_x catalysts for HCHO oxidation at low temperature.