Effects of current densities on the formation of LiCoO<Subscript>2</Subscript>/graphite lithium ion battery

The activation characteristics and the effects of current densities on the formation of a separate LiCoO₂ and graphite electrode were investigated and the behavior also was compared with that of the full LiCoO₂/graphite batteries using various electrochemical techniques. The results showed that the formation current densities obviously influenced the electrochemical impedance spectrum of Li/graphite, LiCoO₂/Li, and LiCoO₂/graphite cells. The electrolyte was reduced on the surface of graphite anode between 2.5 and 3.6 V to form a preliminary solid electrolyte interphase (SEI) film of anode during the formation of the LiCoO₂/graphite batteries. The electrolyte was oxidized from 3.95 V vs Li⁺/Li on the surface of LiCoO₂ to form a SEI film of cathode. A highly conducting SEI film could be formed gradually on the surface of graphite anode, whereas the SEI film of LiCoO₂ cathode had high resistance. The LiCoO₂ cathode could be activated completely at the first cycle, while the activation of the graphite anode needed several cycles. The columbic efficiency of the first cycle increased, but that of the second decreased with the increase in the formation current of LiCoO₂/graphite batteries. The formation current influenced the cycling performance of batteries, especially the high-temperature cycling performance. Therefore, the batteries should be activated with proper current densities to ensure an excellent formation of SEI film on the anode surface.     

Morphology and modulus evolution of graphite anode in lithium ion battery: An in situ AFM investigation

We investigated the interfacial electrochemical processes on graphite anode of lithium ion battery by using highly oriented pyrolytic graphite(HOPG)as a model system.In situ electrochemical atomic force microscopy experiments were performed in 1M lithium bis(trifluoromethanesulfonyl)imide/ethylene carbonate/diethyl carbonate to reveal the formation process of solid electrolyte interphase(SEI)on HOPG basal plane during potential variation.At 1.45 V,the initial deposition of SEI began at the defects of HOPG surface.After that,direct solvent decomposition took place at about 1.3 V,and the whole surface was covered with SEI.The thickness of SEI was 10.4±0.2 nm after one cycle,and increased to 13.8±0.2 nm in the second cycle,which is due to the insufficient electron blocking ability of the surface film.The Young’s modulus of SEI was measured by a peak force quantitative nanomechanical mapping(QNM).The Young’s modulus of SEI is inhomogeneous.The statistic value is 45±22 MPa,which is in agreement with the organic property of SEI on basal plane of HOPG.     

In situ AFM studies of SEI formation at a Sn electrode

Early stages of the solid electrolyte interphase (SEI) formation at a tin foil electrode in an ethylene carbonate (EC) based electrolyte were investigated by in situ AFM and cyclic voltammetry (CV) at potentials >0.7 V, i.e., above the potential of Sn–Li alloying. We detected and observed initial steps of the surface film formation at ～2.8 V vs. Li/Li⁺ followed by gradual film morphology changes at potentials 0.7 < U < 2.5 V. The SEI layer undergoes continuous reformation during the following CV cycles between 0.7 and 2.5 V. The surface film on Sn does not effectively prevent the electrolyte reduction and a large fraction of the reaction products dissolve in the electrolyte. The unstable SEI layer on Sn in EC-based electrolytes may compromise the use of tin-based anodes in Li-ion battery systems unless the interfacial chemistry of the electrode and/or electrolyte is modified.     

Surface film formation on a graphite electrode in Li‐ion batteries: AFM and XPS study

The formation of a passivation film (solid electrolyte interphase, SEI) at the surface of the negative electrode of full LiCoO₂/graphite lithium‐ion cells using LiPF₆ (1M ) in carbonate solvents as electrolyte was investigated by means of x‐ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). The analyses were carried out at different potentials of the first and the fifth cycles, showing the potential‐dependent character of the surface‐film species formation. These species were mainly identified as Li₂CO₃ up to 3.8 V and LiF up to 4.2 V. This study shows the formation of the SEI during charging and its partial dissolution during discharge. Copyright © 2005 John Wiley & Sons, Ltd.     

The understanding of solid electrolyte interface (SEI) formation and mechanism as the effect of flouro-o-phenylenedimaleimaide (F-MI) additive on lithium-ion battery

Solid electrolyte interface (SEI) is a critical factor that influences battery performance. SEI layer is formed by the decomposition of organic and inorganic compounds after the first cycle. This study investigates SEI formation as a product of electrolyte decomposition by the presence of flouro-o-phenylenedimaleimaide (F-MI) additive. The presence of fluorine on the maleimide-based additive can increase storage capacity and reversible discharge capacity due to high electronegativity and high electron-withdrawing group. The electrolyte containing 0.1 wt% of F-MI-based additive can trigger the formation of SEI, which could suppress the decomposition of remaining electrolyte. The reduction potential was 2.35 to 2.21 V vs Li/Li⁺ as examined by cyclic voltammetry (CV). The mesocarbon microbeads (MCMB) cell with F-MI additive showed the lowest SEI resistance (Rsei) at 5898 Ω as evaluated by the electrochemical impedance spectroscopy (EIS). The morphology and element analysis on the negative electrode after the first charge-discharge cycle were examined by scanning electron microscopy (SEM), energy dispersive spectrometry (EDS), and X-ray photoelectron spectroscopy (XPS). XPS result showed that MCMB cell with F-MI additive provides a higher intensity of organic compounds (RCH₂OCO₂Li) and thinner SEI than MCMB cell without an additive that provides a higher intensity of inorganic compound (Li₂CO₃ and Li₂O), which leads to the performance decay. It is concluded that attaching the fluorine functional group on the maleimide-based additive forms the ideal SEI formation for lithium-ion battery.     

Initial solid electrolyte interphase formation process of graphite anode in LiPF6 electrolyte: an in situ ECSTM investigation

Understanding the structure and formation dynamics of the solid electrolyte interphase (SEI) on the electrode/electrolyte interface is of great importance for lithium ion batteries, as the properties of the SEI remarkably affect the performances of lithium ion batteries such as power capabilities, cycling life, and safety issues. Herein, we report an in situ electrochemical scanning tunnelling microscopy (ECSTM) study of the surface morphology changes of a highly oriented pyrolytic graphite (HOPG) anode during initial lithium uptake in 1 M LiPF(6) dissolved in the solvents of ethylene carbonate plus dimethyl carbonate. The exfoliation of the graphite originating from the step edge occurs when the potential is more negative than 1.5 V vs. Li(+)/Li. Within the range from 0.8 to 0.7 V vs. Li(+)/Li, the growth of clusters on the step edge, the decoration of the terrace with small island-like clusters, and the exfoliation of graphite layers take place on the surface simultaneously. The surface morphology change in the initial lithium uptake process can be recovered when the potential is switched back to 2.0 V. Control experiments indicate that the surface morphology change can be attributed to the electrochemical reduction of solvent molecules. The findings may lead to a better understanding of SEI formation on graphite anodes, optimized electrolyte systems for it, as well as the use of in situ ECSTM for interface studies in lithium ion batteries.     

Interfacial processes at single-crystal β-Sn electrodes in organic carbonate electrolytes

In situ atomic force microscopy (AFM) and spectroscopic ellipsometry were used to study the mechanism of organic carbonate electrolytes decomposition and surface layer (re)formation at β-Sn(001) and (100) single crystal electrodes. Interfacial phenomena were investigated at potentials above 0.8 V vs. Li/Li⁺, i.e. where no Sn–Li alloying takes place. The Sn(001) electrode tends to form a protective surface layer of electrolyte reduction products during the first cathodic CV scan, which effectively inhibits further reduction of the electrolyte upon cycling. In contrast, the Sn(100) electrode produces a thick, inhomogeneous and unstable surface layer. The observed significant difference of Sn reactivity toward the electrolyte as a function of Sn surface crystalline orientation suggests radically different reaction paths, reduction products, and properties of the surface film.     

Nanocrystalline cellulose-reinforced composite mats for lithium-ion batteries: electrochemical and thermomechanical performance

Nanocrystalline cellulose (NCC)-reinforced poly(vinylidenefluoride-co-hexafluoropropylene) (PVdF-HFP) composite mats have been prepared by electrospinning method. Polymer electrolytes formed by activating the composite mats with 1 M lithium bis(trifluoromethanesulfonyl)imide/1-butyl-3-methypyrrolidinium bis(trifluoromethanesulfonyl)imide electrolyte solution. The addition of 2 wt% NCC in PVdF-HFP improved the electrolyte retention and storage modulus of the separator by 63 and 15 %, respectively. The developed electrolyte demonstrated high value of ionic conductivity viz. 4?×?10^?4?S?cm^?1 at 30 °C. Linear scan voltammetry revealed a wide electrochemical stability of the composite mat separator up to 5 V (vs. Li⁺/Li). Cyclic voltammetry of the polymer electrolyte with a graphite electrode in 2.5 to 0 V (vs. Li⁺/Li) potential range showed a reversible intercalation/de-intercalation of Li⁺ ions in the graphite. No peaks were observed related to the reduction of the electrolyte on the anode.     

Ionic Liquid Electrolyte with Weak Solvating Molecule Regulation for Stable Li Deposition in High-Performance Li−O2 Batteries

Li−O₂ batteries with bis(trifluoromethanesulfonyl)imide-based ionic liquid (TFSI-IL) electrolyte are promising because TFSI-IL can stabilize O₂⁻ to lower charge overpotential. However, slow Li⁺ transport in TFSI-IL electrolyte causes inferior Li deposition. Here we optimize weak solvating molecule (anisole) to generate anisole-doped ionic aggregate in TFSI-IL electrolyte. Such unique solvation environment can realize not only high Li⁺ transport parameters but also anion-derived solid electrolyte interface (SEI). Thus, fast Li⁺ transport is achieved in electrolyte bulk and SEI simultaneously, leading to robust Li deposition with high rate capability (3 mA cm⁻²) and long cycle life (2000 h at 0.2 mA cm⁻²). Moreover, Li−O₂ batteries show good cycling stability (a small overpotential increase of 0.16 V after 120 cycles) and high rate capability (1 A g⁻¹). This work provides an effective electrolyte design principle to realize stable Li deposition and high-performance Li−O₂ batteries.     

白藜芦醇对长期贮存锂离子电池电解液性能的影响

锂离子电池电解液从制造完成到使用,一般都会经历灌装、运输和贮存的过程,了解长期贮存过程对锂离子电池电解液性能的影响,对锂离子电池的生产具有一定的理论指导意义.本文运用电化学阻抗谱(EIS)测试并结合循环伏安法(CV)测试、充放电测试、扫描电子显微镜(SEM)等研究了1 mol.L-1 LiPF6-EC:EMC 基础电解...     

LiCoO<Subscript>2</Subscript> electrode/electrolyte interface of Li-ion batteries investigated by electrochemical impedance spectroscopy

The storage behavior and the first delithiation of LiCoO₂ electrode in 1 mol/L LiPF₆-EC:DMC:DEC electrolyte were investigated by electrochemical impedance spectroscopy (EIS). It has found that, along with the increase of storage time, the thickness of SEI film increases, and some organic carbonate lithium compounds are formed due to spontaneous reactions occurring between the LiCoO₂ electrode and the electrolyte. When electrode potential is changed from 3.8 to 3.95 V, the reversible breakdown of the resistive SEI film occurs, which is attributed to the reversible dissolution of the SEI film component. With the increase of electrode potential, the thickness of SEI film increases rapidly above 4.2 V, due to overcharge reactions. The inductive loop observed in impedance spectra of the LiCoO₂ electrode in Li/LiCoO₂ cells is attributed to the formation of a Li_1−x CoO₂/LiCoO₂ concentration cell. Moreover, it has been demonstrated that the lithium-ion insertion-deinsertion in LiCoO₂ hosts can be well described by both Langmuir and Frumkin insertion isotherms, and the symmetry factor of charge transfer has been evaluated at 0.5. Supported by the Special Funds for Major State Basic Research Project of China (Grant No. 2002CB211804)     

A review on electrode and electrolyte for lithium ion batteries under low temperature

Under low temperature (LT) conditions (−80 °C∼0 °C), lithium-ion batteries (LIBs) may experience the formation of an extensive solid electrolyte interface (SEI), which can cause a series of detrimental effects such as Li⁺ deposition and irregular dendritic filament growth on the electrolyte surface. These issues ultimately lead to the degradation of the LT performance of LIBs. As a result, new electrode/electrolyte materials are necessary to address these challenges and enable the proper functioning of LIBs at LT. Given that most electrochemical reactions in lithium-ion batteries occur at the electrode/electrolyte interface, finding solutions to mitigate the negative impact caused by SEI is crucial to improve the LT performance of LIBs. In this article, we analyze and summarize the recent studies on electrode and electrolyte materials for low temperature lithium-ion batteries (LIBs). These materials include both metallic materials like tin, manganese, and cobalt, as well as non-metallic materials such as graphite and graphene. Modified materials, such as those with nano or alloying characteristics, generally exhibit better properties than raw materials. For instance, Sn nanowire-Si nanoparticles (SiNPs−In-SnNWs) and tin dioxide carbon nanotubes (SnO₂@CNT) have faster Li⁺ transport rates and higher reversible capacity at LT. However, it′s important to note that when operating under LT, the electrolyte may solidify, leading to difficulty in Li⁺ transmission. The compatibility between the electrolyte and electrode can affect the formation of the solid electrolyte interphase (SEI) and the stability of the electrode/electrolyte system. Therefore, a good electrode/electrolyte system is crucial for successful operation of LIBs at LT.     

In situ analysis of interfacial reactions between negative MCMB,lithium electrodes,and gel polymer electrolyte

The interfacial properties of mesocarbon-microbeads (MCMB) and lithium electrodes during charge process in poly (vinylidenefluoride-co-hexafluoropropylene)-based gel electrolyte were investigated by in situ Raman microscopy, in situ Fourier transform-infrared (FTIR) spectroscopic methods, and charge–discharge, electrochemical impedance spectroscopy techniques. For MCMB electrode, the series phase transitions from initial formation of the dilute stage 1 graphite intercalation compound (GIC) to a stage 4 GIC, then through a stage 3 to stage 2, and finally to stage 1 GIC was proved by in situ Raman spectroscopic measurement. The formation of solid electrolyte interface (SEI) films formed on MCMB and metal lithium electrode was studied by in situ reflectance FTIR spectroscopic method. At MCMB electrode surface, the solvent (mostly ethylene carbonate) decomposed during charging process and ROCO₂Li may be the product. ROCO₂Li, ROLi, and Li₂CO₃ were the main composites of SEI film formed on lithium electrode, not on electrodeposited lithium electrode or lithium foil electrode.     

电解液添加剂硫酸亚乙酯对锂离子电池性能的影响

在1 mol/L LiPF₆/碳酸乙烯酯+碳酸二甲酯+碳酸甲乙酯（体积比1∶1∶1）电解液中,采用恒流充放电测试、循环伏安法（CV）、扫描电子显微镜（SEM）、能量散射光谱（EDS）、电化学阻抗谱（EIS）等测试技术,研究了添加剂硫酸亚乙酯（DTD）对锂离子电池性能及石墨化中间相碳微球（MCMB）电极/电解液界面性质的影响。 结果表明,在电解液中引入体积分数0.01%DTD后,MCMB/Li电池可逆放电容量从300 mA·h/g提高至350 mA·h/g,电池总阻抗降低,循环稳定性提高。CV测试发现,在首次还原过程中,DTD在电极电位1.4 V左右（vs Li/Li⁺）发生电化学还原,参与了MCMB电极表面固体电解质相界面膜（SEI膜）的形成过程。 同时,DTD对LiMn₂O₄电极性能无不良影响。     

Atomic force microscopy study on the stability of a surface film formed on a graphite negative electrode at elevated temperatures

The stability at elevated temperatures of a solid electrolyte interphase (SEI) formed on a graphite negative electrode in lithium ion batteries was investigated by storage tests and in situ atomic force microscopy (AFM) observation. When the fully discharged graphite electrode was stored at elevated temperatures, the irreversible capacity in the following cycle increased remarkably. On the other hand, when the electrode was stored at the fully charged state at elevated temperatures, it was severely self-discharged during storage. AFM observation of the SEI layer formed on a model electrode of highly oriented pyrolytic graphite revealed two important facts on the stability of the SEI at elevated temperatures: (i) dissolution and agglomeration of the SEI layer at the discharged state and (ii) serious SEI growth at the charged state. These phenomena well explain the results of the charge and discharge tests. It was also shown that the addition of vinylene carbonate greatly improves the stability of the SEI at elevated temperatures, and gives good charge and discharge performance after storage.     

单晶硅片负极界面形貌的原位AFM探测

利用原子力显微镜原位研究单晶硅片负极在首次充放电循环中的界面形貌变化。硅负极表面固体电解质界面(SEI)膜的形成过程为：初始SEI膜从1.5 V开始形成,在1.25–1.0 V之间生长快速,0.6 V左右生长缓慢。初始SEI膜具有层状结构的特征,表层薄膜较软,下层呈颗粒状,机械稳定性较好。在锂化电位下,硅负极表面的单晶结构逐渐变得颗粒化,发生不可逆的结构变化。经过首个充放电循环后,硅负极表面被厚度不均一的SEI膜所覆盖,SEI膜的厚度大约为10–40 nm。     

LiCoO_2 electrode/electrolyte interface of Li-ion batteries investigated by electrochemical impedance spectroscopy

The storage behavior and the first delithiation of LiCoO2 electrode in 1 mol/L LiPF6-EC:DMC:DEC elec- trolyte were investigated by electrochemical impedance spectroscopy (EIS). It has found that, along with the increase of storage time, the thickness of SEI film increases, and some organic carbonate lithium compounds are formed due to spontaneous reactions occurring between the LiCoO2 electrode and the electrolyte. When electrode potential is changed from 3.8 to 3.95 V, the reversible breakdown of the resistive SEI film occurs, which is attributed to the reversible dissolution of the SEI film component. With the increase of electrode potential, the thickness of SEI film increases rapidly above 4.2 V, due to overcharge reactions. The inductive loop observed in impedance spectra of the LiCoO2 electrode in Li/LiCoO2 cells is attributed to the formation of a Li1-xCoO2/LiCoO2 concentration cell. Moreover, it has been demonstrated that the lithium-ion insertion-deinsertion in LiCoO2 hosts can be well described by both Langmuir and Frumkin insertion isotherms, and the symmetry factor of charge transfer has been evaluated at 0.5.     

锂离子电池电解液中甲醇杂质对石墨电极性能影响机制的电化学阻抗谱研究

运用电化学阻抗谱和循环伏安法研究了在1mol/LLiPF6-EC/DEC/DMC电解液中,不同甲醇杂质含量对石墨电极性能的影响及其机制.结果表明,甲醇对石墨电极性能的影响与电解液中甲醇的含量有关;其对石墨电极性能的影响机制为甲醇在2.0V左右还原生成的甲氧基锂沉积在石墨电极表面上,形成一层初始SEI膜,影响了EC的还原分解成膜过程.     

Polymer/colloid dual-phase electrolyte membrane for rechargeable lithium batteries

In this work, a polymer/ceramic phase-separation porous membrane is first prepared from polyvinyl alcohol–polyacrylonitrile water emulsion mixed with fumed nano-SiO₂ particles by the phase inversion method. This porous membrane is then wetted by a non-aqueous Li–salt liquid electrolyte to form the polymer/colloid dual-phase electrolyte membrane. Compared to the liquid electrolyte in conventional polyolefin separator, the obtained electrolyte membrane has superior properties in high ionic conductivity (1.9 mS?cm^?1 at 30 °C), high Li⁺ transference number (0.41), high electrochemical stability (extended up to 5.0 V versus Li⁺/Li on stainless steel electrode), and good interfacial stability with lithium metal. The test cell of Li/LiCoO₂ with the electrolyte membrane as separator also shows high-rate capability and excellent cycle performance. The polymer/colloid dual-phase electrolyte membrane shows promise for application in rechargeable lithium batteries.     

An azamacrocyclic electrolyte additive to suppress metal deposition in lithium-ion batteries

An azamacrocyclic compound (1,4,8,11-tetraazacyclotetradecane, cyclam), which forms strong chelate complexes with metal ions such as Mn(II) and Fe(II), is tested as an electrolyte additive to suppress metal deposition. The tetradentate cyclic ligand is electrochemically stable within the working voltage of lithium-ion batteries (0.0–4.5 V vs. Li/Li⁺), hence it is practicable as an electrolyte additive. Deposition of Mn on a graphite electrode, which is severe when a Li/graphite cell is cycled in a Mn(II)-containing electrolyte solution, is greatly suppressed by adding cyclam. Our elemental analysis reveals negligible Mn deposits on a graphite electrode indicating the beneficial role of cyclam. The suppression of metal deposition is further indicated by the absence of an internal short between Li metal and lithium cobalt oxide positive electrode.