Charge transfer behavior of Poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C61‐butyric acid methyl eser (PCBM) in solutions and in films were examined by photoluminescence (PL) spectroscopy. PL study in solutions indicated that separation distance between P3HT and PCBM affected charge transfer efficiency more seriously than the interface area issue between P3HT and PCBM. P3HT/PCBM film showed very effective photo‐induced charge transfer before post‐thermal annealing on the bi‐layer P3HT/PCBM film. Charge transfer efficiency was gradually diminished by the annealing‐induced phase separation between P3HT and PCBM as revealed by increasing PL emission intensity of P3HT. 相似文献
An easily accessible DPP‐based small molecule ( DMPA‐DTDPP ) has been synthesized by a simple and efficient route. The resulting molecule, when incorporated into a P3HT:PCBM‐based BHJ solar cell, is found to significantly improve the efficiency. The utility of DMPA‐DTDPP as an additive yields an increase in the short circuit current density (Jsc) because DMPA‐DTDPP serves as an energy funnel for P3HT excitons at the P3HT:PCBM interfaces, resulting in an improved overall power conversion efficiency, compared to the P3HT:PCBM control device. Considering the trouble‐free and cost effective synthesis of DMPA‐DTDPP , it may prove very useful in high‐performance solar cells. 相似文献
Two small molecules named PI‐DPP and NI‐DPP with a DPP core as the central strong acceptor unit and phthalimide/naphthalimide as the terminal weak acceptor were designed and synthesized. The effects of terminal phthalimide/naphthalimide units on the thermal behavior, optical and electrochemical properties, as well as the photovoltaic performance of these two materials were systematically studied. Cyclic voltammetry revealed that the lowest unoccupied molecular orbitals (LUMO) (~ ‐3.6 eV) of both molecules were intermediate to common electron donor (P3HT) and acceptor (PCBM). This indicated that PI‐DPP and NI‐DPP may uniquely serve as electron donor when blended with PCBM, and as electron acceptor when blended with P3HT, where sufficient driving forces between DPPs and PCBM, as well as between P3HT and DPPs should be created for exciton dissociation. Using as electron donor materials, PI‐DPP and NI‐DPP devices exhibited low power conversion efficiencies (PCEs) of 0.90% and 0.76% by blending with PCBM, respectively. And a preliminary evaluation of the potential of the NI‐DPP as electron acceptor material was carried out using P3HT as a donor material, and P3HT: NI‐DPP device showed a PCE of 0.6%, with an open circuit voltage (V OC) of 0.7 V, a short circuit current density (J SC) of 1.91 mA•cm‐2, and a fill factor (FF) of 45%. 相似文献
To increase the open circuit voltage (VOC) of polymer solar cells (PSCs) based on polythiophene, two new ester group functionalized polythiophene derivatives, PCTDT and PCTBDT, were designed and synthesized via alternating copolymerization of thiophene‐3‐carboxylate (CT) with the 2,2′‐bithiophene (DT) and benzodithiophene (BDT) units, respectively. The resulting copolymers exhibited broad and strong absorptions in the visible region, which was similar to that of the commonly used poly(3‐hexylthiophene) (P3HT). Through cyclic voltammetry measurements, it was found that both copolymers showed lower HOMO energy levels (−5.27 eV for PCTDT and −5.36 eV for PCTBDT) than that of P3HT (−5.03 eV), indicating that the HOMO energy level could be efficiently reduced by introducing the ester group into the polymer side chain. Photovoltaic properties of the copolymers blended with [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM) as electron acceptor were investigated. The obtained two devices possessed both relatively large short circuit current (ISC) and higher VOC than that of P3HT:PCBM blend. For PCTBDT:PCBM blend, a power conversion efficiency (PCE) up to 2.32%, an ISC of 6.94 mA · cm−2, and a VOC of 0.80 V were observed while PCTDT:PCBM system demonstrated a PCE of 1.75% with a VOC of 0.68 V.
The characteristic absorption spectra of three kinds of phases, the isolated, ordered, and disordered phases, in a solvent‐vapor annealed poly(3‐hexylthiophene)/[6,6]‐phenyl‐C61‐butyric acid methyl ester (P3HT/PCBM) blend film were studied by means of spectroelectrochemistry (SEC) and time‐resolved absorption spectroscopy (TAS). The results reveal that the content of three phases are 12 % isolated, 37 % ordered, and 51 % disordered for the annealed P3HT neat film, and 25 % isolated, 31 % ordered, and 44 % disordered for the annealed P3HT/PCBM blend film. The vertical distribution of the different phases in the blend film was studied by SEC, and the results show that the ordered and isolated phases are mainly distributed in the top and in the bottom of the annealed films, respectively, while the disordered phase is mainly distributed in the middle and the bottom of the films. 相似文献
Vinyl addition homo‐ and copolymerization of norbornene monomer ( M1 ) functionalized with a PCBM moiety using a Pd(II) catalyst in combination with a 1‐octene chain transfer agent efficiently produces polynorbornenes with side‐chain PCBM groups. Characterization by NMR spectroscopy and elemental analysis reveals that the copolymers constitute a well‐defined polymer structure with controlled incorporation of M1 . Although the homopolymer is insoluble in organic solvents, the copolymers containing 62 mol% ( P2 ) and 50 mol% ( P3 ) of the PCBM moiety are soluble in chlorinated solvents such as o‐dichlorobenzene. The bulk‐heterojunction organic photovoltaic devices fabricated based on the P3HT: P3 blends show that P3 can adequately function as an electron acceptor, leading to a cell with a power conversion efficiency of 1.5%, which is outstanding among the polymeric rivals. 相似文献
Phase separation in the donor‐acceptor blend poly(3‐hexylthiophene‐2,5‐diyl):[6,6]‐phenyl‐C61‐butyric acid methyl ester (P3HT:PCBM) during evaporation of a solvent using coarse‐grained molecular dynamics simulations is studied here. To this end, an equilibrated P3HT:PCBM:solvent mixture is placed in an elongated simulation box, after which solvent molecules are removed at regular time intervals from a region above the film. Three often‐used solvents are considered: chloroform (CFM), chlorobenzene (CLB), and orthodichlorobenzene (oDCB). The coarse‐grained solvent–solvent interaction parameters are tuned to reproduce the atmospheric boiling temperatures, while the PCBM–solvent interaction parameters are tuned to reproduce the PCBM solubilities. Other parameters are taken from the literature. During evaporation, the formation of a crust that is depleted of solvent, in which aggregation of P3HT and PCBM occurs, is observed. In agreement with experiment, the top region of the dry film is rich in PCBM for the cases of CLB and oDCB, and rich in P3HT for the case of CFM, while the very top layer of the film is always rich in P3HT. This vertical separation is ascribed to a competition between the tendency of P3HT to move to the surface due to its low surface energy and the different tendencies of PCBM to be dragged along to the surface by the evaporating solvent depending on its solubility. Also in agreement with experiment, the P3HT–PCBM interface area is larger for CLB and oDCB than for CFM. For CLB and oDCB, an indication for a spinodal P3HT–PCBM decomposition starting from the top and bottom surface is found, whereas for CFM the phase separation appears to be initiated in the bulk of the film.