Magnesium chloride supported high mileage catalysts for olefin (decene-1) polymerization XV. Termination and energetics

Polymerizations of decene-1 were carried out from 0° to 70° at A/T = 167 and [M] = 0.75 M initiated by 0.17, 0.34, and 0.69 mM of Ti contained in the MgCl₂/ethylbenzoate/p-cresol/AlEt₃/TiCl₄-AlEt₃/methyl-p-toluate catalyst. The rate of polymerization is directly proportional to the catalyst concentration. About 12% of the Ti in the catalyst is initially active at 50°; they are 1.4%, 8.8%, and 9.4% at 0°, 25°, and 70°, respectively. The changes of R_p with temperature parallels the variations in the active site concentration. The decline of R_p with time has second-order plots with slopes which are inversely proportional to the catalyst concentration, but the rate constants for these deactivations are nearly the same for decene and propylene polymerizations. These results strongly support a mechanism of deactivation involving two adjacent sites in the catalyst particle surfaces. The rate constants of propagation and of chain transfer to AlEt₃, the energetics for these processes, and MW and MW distribution data have been obtained.     

Aqueous/organic biphasic hydroformylation of 1‐octene catalyzed by Co2(CO)8/Ph2P(CH2CH2O)nMe

The aqueous/organic biphasic hydroformylation of 1‐octene catalyzed by Co₂(CO)₈/Ph₂P(CH₂CH₂O)_nMe, an in situ formed thermoregulated phase‐transfer cobalt catalyst, has been developed. The catalyst activity in this biphasic system was as high as that in the homogeneous system. The yield of oxo‐products was 93% when the reaction was carried out at 180 °C and under 4.0 MPa syngas pressure for 20 h. The catalyst could be easily recovered in the aqueous phase by decanting after the reaction system was cooled, and reused in consecutive reaction without any treatment. The loss of Co in the organic phase was less than 1% on average of five successive runs. Copyright © 2012 John Wiley & Sons, Ltd.     

Solid–liquid phase alkylation of P=O–functionalized CH acidic compounds utilizing phase transfer catalysis and microwave irradiation

Optimum conditions for the solid–liquid phase alkylation of methylenebis(diphenylphosphine oxide) (MBDPPO) and ethyl cyanomethylphosphonate (ECMP) were explored studying the role of phase transfer catalysis and microwave (MW) irradiation, as well as the effect of the cation of the alkali carbonate. It was found that the alkylation of MBDPPO may be best accomplished in acetonitrile, in the presence of a quaternary ammonium salt and Cs₂CO₃, while that of ECMP in the absence of catalyst and solvent using K₂CO₃. MW irradiation was beneficial in both cases. During the alkylation of ECMP, by‐products coming from the alcoholysis of the diethyl ester were also identified. © 2011 Wiley Periodicals, Inc. Heteroatom Chem 22:174–179, 2011; View this article online at wileyonlinelibrary.com . DOI 10.1002/hc.20673     

Nucleophilic substitution of ferrocenyl alcohols catalyzed by bismuth(III) in aqueous medium at room temperature

A nucleophilic substitution reaction of an α‐ferrocenyl alcohol with various amines, indoles and thiols was successfully developed by using a catalytic amount of Bi(NO₃)₃.5H₂O at room temperature without the aid of phase transfer catalyst. The reactions proceeded in aqueous media, leading to the formation of new C=C, C=N and C=S bonds bearing ferrocenyl substituent with high efficiency. Copyright © 2012 John Wiley & Sons, Ltd.     

Copper‐mediated initiators for continuous activator regeneration atom transfer radical polymerization of acrylonitrile

Initiators for continuous activator regeneration atom transfer radical polymerization technique was first accessed to acrylonitrile by using CuBr₂/2,2′‐bipyridine as the catalyst, ethyl 2‐bromoisobutyrate as the halogen initiator, and azobis(isobutyronitrile) as the free radical initiator. The key to success is ascribed to the facile achievement of the rapid equilibrium between active species and dormant species. Effects of ligand, catalyst concentration, free radical initiator concentration, and reaction temperature on the polymerization reaction and molecular weight (MW) as well as polydispersity index (PDI) were investigated in detail. The polymerization proceeded in a controlled/living fashion even though the concentration of copper catalyst decreased to 50 ppm, which is evident in pseudo first‐order kinetics of polymerization, linear increase of molecular weight, low PDI, and high chain‐end functionality of the generated polymer. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Kinetics of graft copolymerization of methyl methacrylate onto polychloroprene with tricaprylylmethylammonium chloride as a phase‐transfer catalyst

The phase‐transfer catalyzed graft copolymerization of methyl methacrylate onto polychloroprene was carried out using tricaprylylmethylammonium chloride as a phase‐transfer catalyst in a two‐phase system of an aqueous Na₂S₂O₈ solution and toluene at 55 °C under a nitrogen atmosphere. The initial rate of graft copolymerization was expressed as the combined terms of quaternary onium cation and peroxydisulfate anion in the aqueous phase rather than the fed concentrations of catalyst and Na₂S₂O₈. The observed initial rate of graft copolymerization was used to analyze the graft copolymerization mechanism with a cycle phase‐transfer initiation step in the heterogeneous liquid–liquid system. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3543–3549, 2000     

Synthesis,conformation transition,liquid crystal phase,and self‐assembled morphology of thermosensitive homopolypeptide

Thermosensitive diethylene glycol‐derived poly(L ‐glutamate) homopolypeptides (i.e., poly‐L ‐EG₂‐Glu) with different molecular weights (MW) (M_n,GPC = 5380–32520) were synthesized via the ring‐opening polymerization (ROP) of EG₂‐L ‐glutamate N‐carboxyanhydride (EG₂‐Glu‐NCA) in N,N‐dimethylformamide solution at 50 °C. Their molecular structure, conformation transition, liquid crystal (LC) phase behavior, lower critical solution temperature (LCST) transition, and morphology evolution were thoroughly characterized by means of FTIR, ¹H NMR, gel permeation chromatography, differential scanning calorimetry, wide angle X‐ray diffraction, polarized optical microscope, transmission electron microscope, and dynamic light scattering. In solid state, the homopolypeptide poly‐L ‐EG₂‐Glu presented a conformation transition from α‐helix to β‐sheet with increasing their MW at room temperature, while it mainly assumed an α‐helix of 80–86% in aqueous solution. Poly‐L ‐EG₂‐Glu showed a thermotropic LC phase with a transition temperature of about 100 °C in solid state, while it gave a reversible LCST transition of 34–36 °C in aqueous solution. The amphiphilic homopolypeptide poly‐L ‐EG₂‐Glu self‐assembled into nanostructures in aqueous solution, and their critical aggregation concentrations decreased with increasing MW. Interestingly, their morphology changed from spherical micelles to worm‐like micelles, then to fiber micelles with increasing MW. This work provides a simple method for the generation of different nanostructures from a thermosensitive biodegradable homopolypeptide. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Tying up loose ends: some mechanistic aspects of catalytic chain transfer

Polymerisation of methyl methacrylate in the presence of two catalytic chain transfer agents has been investigated. Several factors were examined to see how they would affect the chain transfer process. Oxygen and initiator impurities added to the system were found to be detrimental. The transfer process was highly intolerant of initiator impurities, but was able to endure a large excess of oxygen. The temperature dependencies of the chain transfer process were determined for cobaloxime boron fluoride (COBF) and cobalt(meso‐Ph₄‐porphyrin) (CoP). The results showed that a study of MW, or k_tr would be a better gauge of the catalyst activity. Activation energies were determined at two concentrations of initiator and it was discovered that the transfer process has a dependence on the initiator concentration. A mechanism for this dependency is proposed that involves a reduction in the active catalyst concentration. As a result, the measured values for C_tr, and k_tr, must be apparent values. An additional consequence of the initiator dependence is that the MW of the polymer products will be directly dependent on the concentration of the initiator.     

Theoretical Study of the Water-Gas Shift Reaction Catalyzed by Tungsten Carbonyls

A density functional theory calculation has been carried out to investigate the mechanism of W(CO)₆ and W₂(CO)₁₀ catalyzed water-gas-shift reaction (WGSR). The calculations indicate that the bimetallic catalyst (W₂(CO)₁₀) would be likely to be more highly active than the mononuclear metal-based catalyst (W(CO)₆) due to the possibility of metal–metal cooperativity in reducing the barriers for the WGSR. The energetic span model is a tool to compute catalytic turnover frequencies (TOFs) which is the traditional measure of the efficiency of a catalyst. The one with the highest efficiency usually gives the highest TOF. The bimetallic catalyst (W₂(CO)₁₀) exhibits high catalytic activity towards WGSR due to the highest value of the calculated TOF (3.62 × 10^?12 s^?1, gas phase; 8.74 × 10^?15 s^?1, solvent phase⁾, which is higher than the value of TOF (8.96 × 10^?20 s^?1, gas phase; 3.96 × 10^?19 s^?1, solvent phase) proposed by Kuriakose et al. (Inorg Chem 51:377–385, 2012). Our results will be important for designing a better catalyst for the industrially important reaction.     

Modification of the (SiO<Subscript>2</Subscript>/MgO/MgCl<Subscript>2</Subscript>)·TiCl<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> Ziegler-Natta polyethylene catalysts using the third metal elements

Various (SiO₂/MgO/MgCl₂)·TiCl _x Ziegler-Natta catalysts modified by the third metal elements were synthesized by the co-impregnation of water-soluble magnesium and the third metal salts. Several key factors including the electronegativity of the third metal elements, catalyst performances in ethylene homo-polymerization, ethylene/1-hexene copolymerization and hydrogen response were systematically investigated. Both the catalyst performance and the polymer properties are influenced by the introduction of the third metal elements. Compared with the unmodified (SiO₂/MgO/MgCl₂)·TiCl _x Ziegler-Natta catalyst, activity and 1-hexene incorporation are enhanced by the introduction of zirconium, vanadium, aluminum and chromium, while deteriorated by the addition of ferrum, nickel, molybdenum and tungsten. Correlations of the catalyst activities and 1-hexene incorporation ability with the electronegativity of the third metal elements are discovered. It is found that the lower electronegativity of the third metal elements leads to the catalyst with higher activity and higher α-olefin co-polymerization ability. The polyethylene produced by a nickel modified catalyst showed broad molecular weight distribution (MWD) and the lowest average molecular weight (MW), while by using a ferrum modified catalyst, the resulting polyethylene had the highest MW, reaching the ultra-high MW area. Vanadium and chromium modified catalysts demonstrated the best hydrogen response.     

Towards the design of novel boron‐ and nitrogen‐substituted ammonia‐borane and bifunctional arene ruthenium catalysts for hydrogen storage

Electronic‐structure density functional theory calculations have been performed to construct the potential energy surface for H₂ release from ammonia‐borane, with a novel bifunctional cationic ruthenium catalyst based on the sterically bulky β‐diketiminato ligand (Schreiber et al., ACS Catal. 2012, 2, 2505). The focus is on identifying both a suitable substitution pattern for ammonia‐borane optimized for chemical hydrogen storage and allowing for low‐energy dehydrogenation. The interaction of ammonia‐borane, and related substituted ammonia‐boranes, with a bifunctional η⁶‐arene ruthenium catalyst and associated variants is investigated for dehydrogenation. Interestingly, in a number of cases, hydride‐proton transfer from the substituted ammonia‐borane to the catalyst undergoes a barrier‐less process in the gas phase, with rapid formation of hydrogenated catalyst in the gas phase. Amongst the catalysts considered, N,N‐difluoro ammonia‐borane and N‐phenyl ammonia‐borane systems resulted in negative activation energy barriers. However, these types of ammonia‐boranes are inherently thermodynamically unstable and undergo barrierless decay in the gas phase. Apart from N,N‐difluoro ammonia‐borane, the interaction between different types of catalyst and ammonia borane was modeled in the solvent phase, revealing free‐energy barriers slightly higher than those in the gas phase. Amongst the various potential candidate Ru‐complexes screened, few are found to differ in terms of efficiency for the dehydrogenation (rate‐limiting) step. To model dehydrogenation more accurately, a selection of explicit protic solvent molecules was considered, with the goal of lowering energy barriers for H‐H recombination. It was found that primary (1°), 2°, and 3° alcohols are the most suitable to enhance reaction rate. © 2014 Wiley Periodicals, Inc.     

Iron‐mediated AGET ATRP of methyl methacrylate using metal wire as reducing agent

Methyl methacrylate (MMA) were successfully polymerized by atom transfer radical polymerization with activator generated by electron transfer (AGET ATRP) using copper or iron wire as the reducing agent at 90°C. Well‐controlled polymerizations were demonstrated using an oxidatively stable iron(III) chloride hexahydrate (FeCl₃·6H₂O) as the catalyst, ethyl 2‐bromoisobutyrate (EBiB) as the initiator, and tetrabutylammonium bromide (TBABr) or triphenylphosphine as the ligand. The polymerization rate was fast and affected by the amount of catalyst and type of reducing agents. For example, the polymerization rate of bulk AGET ATRP with a molar ratio of [MMA]₀/[EBiB]₀/[FeCl₃·6H₂O]₀/[TBABr]₀ = 500/1/0.5/1 using iron wire (the conversion reaches up to 82.2% after 80 min) as the reducing agent was faster than that using copper wire (the conversion reaches up to 86.1% after 3 h). At the same time, the experimental M_n values of the obtained poly(methyl methacrylate) were consistent with the corresponding theoretical ones, and the M_w/M_n values were narrow (～1.3), showing the typical features of “living”/controlled radical polymerization. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Condensation polymers containing silicon and germanium in the main chain

Poly(carbonates), poly(thiocarbonates) and poly(esteres) containing silicon and/or germanium in the main chain were obtained under phase transfer conditions. Polymers were synthesized in a biphasic system NaOH/CH₂Cl₂ at 20°C using several phase transfer catalysts, and characterized by IR and ¹H and ¹³C NMR. The results were evaluated by the yields and the inherent viscosity values. The process was effective observing an increase of both parameters in comparison with the essays without catalyst. The increases depended of the nature of the polymer and the catalyst. In poly(ester) synthesis there was an increase of these parameters when the NaOH concentration was increased due to a salting out effect of the diphenolate from the aqueous phase to the organic one. Also poly(amides) containing silicon or germanium were synthesized by solution polymerization.     

Microwave assisted non-aqueous sol–gel synthesis of LiNiPO4 and its copper doped analogues

A series of single phase LiNi_(1?x)Cu_xPO₄ (0 < x < 0.99) was successfully synthesized by non-aqueous sol–gel method followed by microwave (MW) annealing. The advantage of MW short span annealing is obvious from the nanometer sized particles compared to reported microparticles. XRD, IR and SEM studies were conducted to investigate the phase purity, crystal structure, lattice parameters and morphology respectively. It was found that 10 min of microwave annealing is a time and cost effective approach to produce single phase compositions at low temperature. X-ray studies confirmed the single phase formation of pure and the doped analogues which were found to be iso-structural with the parent LiNiPO₄ compound. The cell parameters with the addition of copper content were in accord with the Vegards law. Impedance studies pointed toward enhanced electrical properties of doped samples as compared to the undoped one.     

SET‐RAFT of MMA mediated by ascorbic acid‐activated copper oxide

In this work, cupric oxide (CuO) or cuprous oxide (Cu₂O) was used as the catalyst for the single electron transfer‐reversible addition‐fragmentation chain transfer (SET‐RAFT) polymerization of methyl methacrylate in the presence of ascorbic acid at 25 °C. 2‐Cyanoprop‐2‐yl‐1‐dithionaphthalate (CPDN) was used as the RAFT agent. The polymerization occurred smoothly after an induction period arising from the slow activation of CuO (or Cu₂O) and the “initialization” process in RAFT polymerization. The polymerizations conveyed features of “living”/controlled radical polymerizations: linear evolution of number‐average molecular weight with monomer conversion, narrow molecular weight distribution, and high retention of chain end fidelity. From the polymerization profile, it was deduced that the polymerization proceeded via a conjunct mechanism of single electron transfer‐living radical polymerization (SET‐LRP) and RAFT polymerization, wherein CPDN acting as the initiator for SET‐LRP and chain transfer agent for RAFT polymerization. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Fast copper catalyzed living radical polymerization of acrylonitrile utilizing a high concentration of radical initiator

This article first reports a fast and controlled living radical polymerization (LRP) of acrylonitrile, evidenced by 81.3% monomer conversion within 40 min and well‐defined the polymers with a narrow polydispersity index (PDI) range of 1.14?1.38. This was achieved by utilizing azobis(isobutyronitrile) as radical initiator with a high concentration up to 190 mM and CuBr₂ as catalyst with a very low concentration down to 50 ppm. The polymerization displayed typical LRP characteristics, including pseudo first‐order kinetics of polymerization, the linear increase of number‐average molecular weights (MWs), low PDI values. The influence of various experimental components, radical initiator concentration, catalyst concentration, and reaction temperature, on the polymerization reaction and MW as well as PDI has been investigated in detail. ¹H NMR and gel permeation chromatography analyses as well as chain extension reaction confirmed the very high chain‐end functionality of the resultant polymer. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Poly(1‐hexene) with long methylene sequences and controlled branches obtained by a thermostable α‐diimine nickel catalyst with bulky camphyl backbone

1‐Hexene polymerizations catalyzed by α‐diimine nickel complexes after activation with modified methylaluminoxane were performed at various reaction temperatures. Effects of catalyst structure and polymerization temperature on activity and polymer microstructure were evaluated in detail. Bulky catalyst 1b with camphyl backbone exhibited good control ability and greatly enhanced thermal stability to be capable of polymerizing 1‐hexene at 80°C. The poly(1‐hexene)s with long methylene sequences and dominate branches (methyl and butyl) were synthesized using catalyst 1b . Differential scanning calorimetry analysis further confirmed that long polymethylene block (? (CH₂)_n? , n > 20) was formed in the poly(1‐hexene)s with melting point of 64°C obtained by catalyst 1b on the basis of initial branched model polyethylene. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Facile synthesis of S-arylisothioureas via the S-arylation of arylthioureas with aryl iodides in water

An environmentally benign, simple and highly efficient protocol for the synthesis of S-arylisothiourea derivatives has been achieved in good to excellent yields by reacting a series of aryl iodides with arylthioureas, using inexpensive CuSO₄·5H₂O as catalyst in water without PTC (phase transfer catalyst). The protocol features easy performance, good to excellent yields, good tolerance towards a variety of functional groups, which could be useful for the preparation of some biologically active compounds.     

Design of Binaphthyl‐Modified Symmetrical Chiral Phase‐Transfer Catalysts: Substituent Effect of 4,4′,6,6′‐Positions of Binaphthyl Rings in the Asymmetric Alkylation of a Glycine Derivative

A series of symmetrical chiral phase‐transfer catalysts with 4,4′,6,6′‐tetrasubstituted binaphthyl units have been designed, and these aryl‐ and trialkylsilyl‐substituted phase‐transfer catalysts, which included a highly fluorinated catalyst, were prepared. The chiral efficiency of these chiral phase‐transfer catalysts was investigated in the asymmetric alkylation of tert‐butylglycinate–benzophenone Schiff base under mild phase‐transfer conditions, and the eminent substituent effect of the 4,4′,6,6′‐positions of the binaphthyl units on enantioselection was observed. In particular, the OctMe₂Si‐substituted catalyst was found to be highly efficient for the phase‐transfer alkylation of tert‐butylglycinate–benzophenone Schiff base with various alkyl halides, including sec‐alkyl halides. The highly fluorinated catalyst was also utilized as a recyclable chiral phase‐transfer catalyst by simple extraction with fluorous solvents.     

Olefin terpolymerizations. III. Symmetry,sterics, and monomer structure in ansa-zirconocenium catalysis of EPDM synthesis

Ethylenebis (η⁵-fluorenyl) zirconium dichloride ( 1 ) and rac-dimethylsilylene bis (1-η⁵-in-denyl) zirconium dichloride ( 2 ) were activated with methylaluminoxane (MAO) to catalyze ethylene (E) propylene (P) copolymerizations. The former produces high MW copolymer at 20°C rich in ethylene with reactivity ratio values of r_E = 1.7 and r_P <0.01, whereas the latter produces lower MW random copolymers with r_E = 1.32 and r_p = 0.36. Ethylidene norbornene (ENB) complexes with 1/MAO but does not undergo insertion in the presence of E and P. In contrast, 2/MAO catalyzes terpolymerization incorporating 9-15 mol % of ENB with slightly lower MW and activity than the corresponding copolymerizations. In comparison, 1,4–hexadiene was incorporated by 2/MAO with much lower A and MW . Terpolymerizations were also conducted with vinylcyclohexene using both catalyst systems. The steric and electronic effects in these processes were discussed. © 1995 John Wiley & Sons, Inc.