圆柱绕流的电磁控制

流体绕过非流线物体时，在物体尾部形成涡街，使其表面周期性变化的阻力和升力增加，从而导致物体振荡，产生噪音。本文通过实验和计算，研究圆柱绕流的电磁控制，阐述浸于弱电介质溶液中，表面包覆电磁激活板的圆柱，在电磁力作用下的流体控制原理，讨论电磁力的消涡、减阻和减振过程。     

流体边界层上电磁力的控制效应研究

利用作用于流体边界层上的电磁体积力改变流体边界层的结构，研究电磁力对流场的控制 作用效果. 电极与磁极交替分布的电磁场激活板包覆在圆柱体表面置于流动的电解质溶液 中，产生的电磁力沿圆柱体表面分布，可以改变流体边界层的结构，从而实现对流场的控制. 用电磁屏蔽和时域控制的方法调整电磁力的时空分布参数，圆柱绕流分离点可以在前驻点和 后驻点之间变动，产生不同的控制效果. 流体边界层上的电磁力能连续控制圆柱绕流、尾流 涡街的形态. 正向电磁力具有较好的消涡、减震和减阻控制效应. 反向电磁力具有明显的增 涡控制效应，具有较强的制动控制效应，此时圆柱体表面涡量分布的对称性和稳定性被破坏.     

圆柱表面包覆电磁场消涡与增涡实验研究

利用电磁体积力改变流体边界层的结构，用作用于流体边界层上的电磁力进行消涡与增涡控制。交替分布的电极和磁极包覆在圆柱体的表面置于电介质溶液中，简单调整电磁力的时间与空间分布可以方便地控制圆柱绕流的形态。通过理论分析和数值模拟确定了实验控制的关键参数，实现了电磁力消涡和增涡的连续控制，电磁力作用下的圆柱绕流的分离点可以在前驻点和后驻点之间变动。     

翼型绕流的电磁力控制

将表面包覆电磁激活板的翼型,按一定的攻角,置于流动的弱电介质溶液中,电磁激活板可产生作用于流体的切向电磁力(Lorentz力),从而改变流体边界层的结构. 在转动水槽中,对翼型绕流及电磁力控制下的绕流形态进行了实验研究. 结果表明,未加电磁力时,前缘涡的脱落点是不确定的,与流场具体条件有关,而后缘涡仅在尖角处脱落. 前缘涡与后缘涡相互影响,并周期性的脱体,在尾部形成涡街. 施加电磁力后,当力的方向与流动方向相同时,可以在一定程度上抑制分离,消除涡街,其效果与减小攻角类似. 加反向电磁力时,则相当于加大攻角,在翼型体的背风面形成涡街.      

分块法研究圆柱绕流升阻力

 使用新的分块耦合方法，分别对单圆柱和串列双圆柱绕流进行了数值 模拟. 对于单圆柱绕流，低$Re$下计算所得到的定常涡尺寸与实验非常接近. 对于 串列双圆柱绕流，研究分析了改变双圆柱中心间距对上下游圆柱的升阻力系数和脉动频率所 产生的影响，计算结果与实验非常吻合，为进一步研究涡致振动提供了依据.     

分块法研究圆柱绕流升阻力

使用新的分块耦合方法，分别对单圆柱和串列双圆柱绕流进行了数值模拟．对于单圆柱绕流，低Re下计算所得到的定常涡尺寸与实验非常接近．对于串列双圆柱绕流，研究分析了改变双圆柱中心间距对上下游圆柱的升阻力系数和脉动频率所产生的影响，计算结果与实验非常吻合，为进一步研究涡致振动提供了依据．     

等离子体激励器控制圆柱绕流的实验研究

为了发展新型移动附面层控制技术,提升流动控制效率,采用粒子图像测速技术,开展了基于对称布局等离子体气动激励的圆柱绕流控制研究,获得了静止空气下,对称布局激励器诱导流场的演化过程,评估了来流条件下等离子体控制效果,通过等离子体诱导涡实现了虚拟移动附面层控制,分析了诱导涡随时间演化的过程,揭示了圆柱绕流等离子体控制机理.结果表明:(1)在静止空气下,对称布局激励器在刚启动瞬间,会在暴露电极两侧诱导产生一对旋转方向相反的启动涡;随着时间的推移,启动涡逐渐向远离壁面的方向运动;随后,激励器在暴露电极两侧产生了两股速度近似相等,方向相反的诱导射流,诱导射流在柯恩达效应的影响下,朝壁面方向发展.(2)当激励电压峰峰值为19.6 kV,激励频率3kHz时,施加等离子体气动激励后,圆柱脱落涡得到了较好抑制,圆柱阻力系数减小了21.8％;(3)在来流作用下,对称布局激励器在靠近来流一侧,诱导产生了较为稳定的涡结构.诱导涡通过旋转、运动,促进了壁面附近低能气流与主流之间的掺混,抑制了圆柱绕流流场分离,实现了"虚拟移动附面层控制"效果.与传统移动附面层控制技术相比,基于等离子体气动激励的新型移动附面层控制技术不需要复杂、笨重的机构,不会带来额外的阻力,具有潜在的应用前景.      

等离子体激励器控制圆柱绕流的实验研究

为了发展新型移动附面层控制技术,提升流动控制效率,采用粒子图像测速技术,开展了基于对称布局等离子体气动激励的圆柱绕流控制研究,获得了静止空气下,对称布局激励器诱导流场的演化过程,评估了来流条件下等离子体控制效果,通过等离子体诱导涡实现了虚拟移动附面层控制,分析了诱导涡随时间演化的过程,揭示了圆柱绕流等离子体控制机理.结果表明:(1)在静止空气下,对称布局激励器在刚启动瞬间,会在暴露电极两侧诱导产生一对旋转方向相反的启动涡;随着时间的推移,启动涡逐渐向远离壁面的方向运动;随后,激励器在暴露电极两侧产生了两股速度近似相等,方向相反的诱导射流,诱导射流在柯恩达效应的影响下,朝壁面方向发展.(2)当激励电压峰峰值为19.6 kV,激励频率3 kHz时,施加等离子体气动激励后,圆柱脱落涡得到了较好抑制,圆柱阻力系数减小了21.8%;(3)在来流作用下,对称布局激励器在靠近来流一侧,诱导产生了较为稳定的涡结构.诱导涡通过旋转、运动,促进了壁面附近低能气流与主流之间的掺混,抑制了圆柱绕流流场分离,实现了"虚拟移动附面层控制"效果.与传统移动附面层控制技术相比,基于等离子体气动激励的新型移动附面层控制技术不需要复杂、笨重的机构,不会带来额外的阻力,具有潜在的应用前景.     

横向振荡圆柱绕流的格子Boltzmann方法模拟

基于格子Boltzmann方法(LBM)对不可压横向振荡圆柱绕流问题进行了数值研究. 与传统的求解宏观的N-S方程的数值方法不同, LBM求解此类问题不需要采用动网格, 而且不需要对网格进行特殊处理, 从而节约了计算成本. 结果显示, 当振荡频率增加到相应的静止圆柱绕流的自然涡脱落频率附近时, 圆柱后最新形成的集中涡距离柱体越来越近, 直到达到一个极限位置. 随后, 集中涡突然转向圆柱体另一侧脱落. 当振荡频率接近于静止圆柱的自然涡脱落频率时, 发生频率同步的现象. 随着振荡频率远离自然涡脱落频率, 同步现象消失. 在几种次谐振荡和超谐振荡下, 尾流区的涡脱落频率仍为相应的静止圆柱绕流的自然涡脱落频率.      

高精度PPM格式在湍流燃烧中的应用

利用处理三维可压缩粘性流体流动问题中的沉浸边界法,并结合基于PPM方法的高精度TVD格式,对三维方形管道中部的圆柱火焰绕流及惰性气体绕流问题进行了数值模拟。计算湍流时采用大涡模拟(LES),化学反应速率采用EBU漩涡破碎模型。通过计算结果与实验结果的比较,发现高精度PPM格式能精确模拟两类圆柱绕流问题。计算中还发现,火焰圆柱绕流算例中,在火焰翻越圆柱前,由于燃烧的膨胀作用,使得火焰正面前的未燃气体流动并形成惰性气体绕流,这与无燃烧时的惰性气体绕流类似。但当火焰翻越圆柱过程中及完全翻越圆柱后,两种算例绕流流场出现明显变化。     

Instability of cylinder wake under open-loop active control

Instability of a wake controlled by a streamwise Lorentz force is investigated through a Floquet stability analysis. The streamwise Lorentz force, which is a two-dimensional control input created by an electromagnetic actuator located on the cylinder surface,adjusts the base flow to affect the three-dimensional wake instability and achieve wake stabilization and transition delay. The instability mode at a Reynolds number Re = 300 can be transformed from B to A with N = 1.0, where N is an interaction number representing the strength of the Lorentz force relative to the inertial force in the fluid. The wake flow is Floquet stable when N increases to 1.3. The spanwise perturbation wavelengths are 3.926 D and 0.822 D in the modes A and B, respectively, where D is the cylinder diameter. In addition, the oscillating amplitudes of drag and lift are reduced with the increase in the interaction number. Particle tracing is used to explore the essential physical mechanism for mode transformation. The path lines show that suppression of flow separation hinders the fluid deformation and rotation, leading to the decrease in elliptic and hyperbolic instability regions, which is the material cause of mode transformation.All of the results indicate that wake stabilization and transition delay can be achieved under open-loop active control via the streamwise Lorentz force.     

包覆电磁场激活板的圆柱尾迹的数值研究

利用电磁场作用于电介质溶液的Lorentz力可以控制溶液的流动.对置于弱电介质溶液中,包覆电磁场激活板的圆柱周围的绕流进行数值研究,讨论了电磁场激活板的安装位置,激活方式等对圆柱尾迹的影响.     

Electromagnetic control of seawater flow around circular cylinders

We investigate numerically the electromagnetic control of seawater flows over an infinitely long circular cylinder. Stripes of electrodes and magnets, wrapped around the cylinder surface, produce a tangential body force (Lorentz force) that stabilizes the flow. This mechanism delays flow separation, reduces drag and lift, and finally suppresses the von Kármán vortex street. Results from two-dimensional simulations of the Navier–Stokes equations in a range 10<Re<300 and Lorentz force calculations are presented. Emphasis is placed on the disclosure of physical phenomena as well as a quantitative detection of the flow field and forces. It is shown that the drag strongly depends on the geometry of the electromagnetic actuator and on its location at the cylinder surface. The effect of flow control increases with larger Reynolds numbers, since the boundary layer thickness and the penetration depth of the Lorentz force are closely connected.     

电磁极宽度对圆柱绕流场影响的数值分析

在雷诺数Re=200的情况,利用Maxwell方程直接数值计算表面包覆电极与磁极圆柱体产生的电磁力分布,将其加入到动量方程中,在各种电磁力作用参数和电磁极宽度的组合下,对表面覆盖电磁极圆柱体在弱电解质中的绕流场结构及其升阻力特性进行了数值模拟与分析.结果表明,当电磁极宽度较小时,圆柱体绕流场的分离点越容易接近后驻点,而电磁力对总阻力的影响并不明显,但对压差和摩擦阻力均有明显影响.当电磁极宽度较大时,圆柱体尾部区域越容易产生射流现象,而且总阻力随电磁力作用参数和电磁极宽度增大而减小.在电磁力尚不足以完全抑制周期性涡脱落的情况下,升力幅值随电磁力作用参数增大而减小,但随电磁极宽度则先减小后略有增加,升力脉动频率则均随电磁力作用参数和电磁极宽度增大而增加.研究表明,电磁力可以有效地改善圆柱体绕流场结构,达到减小圆柱体阻力并抑制其脉动升力之目的,因此是圆柱型结构的一种有效流动控制手段.     

Numerical study of the suppression mechanism of vortex-induced vibration by symmetric Lorentz forces

In this paper, the electro-magnetic control of vortex-induced vibration (VIV) of a circular cylinder is investigated numerically based on the stream function–vorticity equations in the exponential–polar coordinates attached on the moving cylinder for Re=150. The effects of the instantaneous wake geometries and the corresponding cylinder motion on the hydrodynamic forces for one entire period of vortex shedding are discussed using a drag–lift phase diagram. The drag–lift diagram is composed of the upper and lower closed curves due to the contributions of the vortex shedding but is magnified, translated and turned under the action of the cylinder motion. The Lorentz force for controlling the vibration cylinder is classified into the field Lorentz force and the wall Lorentz force. The symmetric field Lorentz force will symmetrize the flow passing over the cylinder and decreases the lift oscillation, which, in turn, suppresses the VIV, whereas the wall Lorentz force has no effect on the lift. The cylinder vibration increases as the work performed by the lift dominates the energy transfer. Otherwise, the cylinder vibration decreases. If the net transferred energy per motion is equal to zero, the cylinder will vibrate steadily or be fixed.     

Investigation of the flow around a circular cylinder under the influence of an electromagnetic force

An investigation of the effect of the local electromagnetic body force on the flow behavior around a circular cylinder is conducted. The electromagnetic force is applied locally on the cylinder surface in the range of 70–130° from the stagnation point along the cylinder circumference in both clockwise and counterclockwise directions. The numerical results predict that the Lorentz force applied in the circumferential direction on the cylinder moves the separation point rearward, and reduces the drag. To validate the numerical results, an experiment is conducted with a circular cylinder of 5 cm diameter. The electrodes and permanent magnets are flush mounted on the cylinder in such a way that the Lorentz force is generated in the circumferential direction. Flow visualization with polystyrene particles and direct drag measurement using strain gages are made. The fluid used is natural sea water of electric conductivity of about 4 (Ω m)^-1. Induction effect can be neglected in the present investigation due to the low flow speed and the Lorentz force is proportional to E×B where E is an applied electric field and B is a magnetic field. Received: 7 June 1998/Accepted: 28 April 1999     

NUMERICAL STUDY ON THE FLOW AROUND A CIRCULAR CYLINDER WITH SURFACE SUCTION OR BLOWING USING VORTICITY-VELOCITY METHOD

A vorticity-velocity method was used to study the incompressible viscous fluid flow around a circular cylinder with surface suction or blowing. The resulted high order implicit difference equations were effeciently solved by the modified incomplete LU decomposition conjugate gradient scheme (MILU-CG). The effects of surface suction or blowing ' s position and strength on the vortex structures in the cylinder wake, as well as on the drag and lift forces at Reynoldes number Re = 100 were investigated numerically. The results show that the suction on the shoulder of the cylinder or the blowing on the rear of the cylinder can effeciently suppress the asymmetry of the vortex wake in the transverse direction and greatly reduce the lift force; the suction on the shoulder of the cylinder, when its strength is properly chosen , can reduce the drag force significantly , too.     

The PELskin project: part IV—control of bluff body wakes using hairy filaments

The passive control of bluff body wakes using a sparse layer of elastic hairy filaments has been investigated via a series of numerical simulations and compared to selected experiments under well-controlled boundary conditions. It has been found that a distribution of filaments spaced half of the dominant three dimensional instability and resonating with the main shedding frequency can drastically delay the three dimensional transition of the wake behind a circular cylinder. It will also be shown that when using a pair of rows of filaments symmetrically spaced by an azimuthal angle, the wake topology can be deeply affected as well as the value of the integral force coefficients of the cylinder. In the most favourable case, a coupled three dimensional transition delay and strongly reduced values of the drag and of the lift fluctuation can be simultaneously achieved. These results hold also for higher Reynolds-number flows as shown in experiments on a cylinder with hairy flaps attached to the aft part. The lock-in effect of structural vibration of the flaps with the vortex shedding is assumed to be the reason for a sudden change in the shedding cycle as soon as the motion amplitude is high enough to modify the wake. In line with this hypothesis, it has been demonstrated that a long elastic filament pinned on the centerline of a forced spatially developing mixing layer can interact with the vortex dynamics delaying the pairing process-leading to a reduced thickness of the layer. These findings show that a properly designed fluid structure interaction can indeed lead to technological benefits in terms of wake control: drag reduction, vibration control and possibly palliation of aeroacoustic emissions.