界面端附近裂纹的应力强度因子

结合材料的断裂形式可分为从界面端产生裂纹（沿界面或向母材内部层折）然后断裂与稍稍离开界面端处产生裂纹然后断裂这两种情况，在金属／陶瓷类结合材料中，后者出现的概率更大，本文利用结合材料界面端的奇异应力场和叠加原理，给出了界面端附近裂纹的应力强度因子近似计算公式，并用边界元数值计算验证了其有效性。     

层状磁电复合材料界面共线裂纹平面问题分析

本文研究了面内电磁势载荷作用下双层压电压磁复合材料中共线界面裂纹问题．考虑了压电材料的导磁性质和压磁材料的介电性质,引入了界面电位移和磁感强度的连续性条件．利用Fourier 变换得到一组第二类Cauchy 型奇异积分方程．进一步导出了相应问题的应力强度因子、电位移强度因子和磁感强度强度因子的表达式,给出了应力强度因子的数值结果．结果表明电磁载荷会导致界面裂纹尖端I、II 混合型应力奇异性,同时还伴随着电位移和磁感强度的奇异性．比较了双裂纹左右端的应力强度因子,发现在面内极化方向上施加面内磁势载荷时共线裂纹内侧尖端区域的两个法向应力场发生互相干涉增强．     

界面裂纹问题中的权函数方法

本文将Ｐａｒｉｓ等确定均匀材料中裂纹尖端应力强度因子的权函数方法推广应用到界面裂纹问题，给出了界面裂纹尖端附近或无限大体半无限界面裂纹问题的权函数的显式表达式。利用此权函数表达式可以很简便地求解界面裂纹尖端附近一些外来作用引起的应力强度因子，比如任意分布力、相变应变、位错和热等。作为一个算例，本文计算了界面一侧一个刃型位错引起的应力强度因子。     

有限尺寸下双材料界面附近裂纹位置对裂纹尖端的影响

随着复合材料的应用和发展,不同材料组成的界面结构越来越受到人们的重视。界面层两侧材料的性能相异会引起材料界面端奇异性,同时界面和界面附近存在裂纹会引起裂尖处的应力奇异性。因此双材料界面附近的力学分析是比较复杂的。本文建立双材料直角界面模型,在材料界面附近预设初始裂纹,计算了有限材料尺寸对界面应力场及其附近裂纹应力强度因子的影响。运用弹性力学中的 Goursat 公式求得直角界面端在有限尺寸下的应力场以及其应力强度系数。通过叠加原理和格林函数法进一步得到在直角界面端附近的裂纹尖端应力强度因子。计算结果表明,在适当范围内改变材料内裂纹与界面之间的距离,界面附近裂纹尖端的应力强度因子随着裂纹与界面距离的增加而减少,并且逐渐趋于稳定。分析结果可以为预测双材料结构复合材料界面失效位置提供参考。     

多层材料结构的界面裂纹尖端复应力强度因子

本文建立了一种多层材料复合结构的界面裂纹问题分析模型。当两种材料之间插入第三种薄层弹性材料，裂纹位于第三种材料与第一或第二种弹性材料的界面上，且插页材料３＾＃的厚度相对于裂纹尺寸或平面内其他尺寸很小时，可以得到该问题裂纹尖端的复应力强度因子通式。本文用有限元法对结果进行了数值验证，并进行了有关问题的讨论。     

界面裂纹非对称扩展模型

提出了一种新的复合材料结构中层间脱层裂纹扩展模型，该模型能够揭示裂纹扩展对裂纹左右尖端能量释放率的相对大小及界面材料性能的依赖性，能够比较真实地揭示复合材料结构层间脱层裂纹扩展复杂性的特点．     

求解界面裂纹应力强度因子的高次权函数法

从界面裂纹完备的特征展开式出发,利用伪正交特性,提出了计算界面裂纹特征展开式系数和应力强度因子的高次权函数法。文中计算的均匀材料应力强度因子,与已有结果吻合得非常好,并给出了同裂纹的应力强度因子Ｋ１／Ｋ０和Ｋ２／Ｋ０随机材料弹性模量比及裂纹长度的变化。     

一种确定结合材料界面端应力强度因子的数值方法

基于弹性力平面问题的基本方程，给出了结合材料界面端的应力奇异性特征方程以及位移场和奇异应力场。提出了一种确定结合材料界面端应力强度因子的数值外插方法。对界面端区域进行了有限元网格单元划分。经过具体实例检验进一步确定了求解应力强度因子的最佳方向，该数值外插法的计算结果精度符合工程应用的要求，为工程材料强度的评价提供了有效的计算途径。     

功能梯度材料的平面断裂力学分析

针对材料参数在厚度方向可能按任意连续变化的梯度材料，给出了一个新的分层模型，利用该模型求解了面内加载下梯度界面层和涂层中的界面裂纹问题，借助Fburier积分技术和传递矩阵方法，将该问题化为一个Cauchy型奇异积分方程，通过数值求解，得到感兴趣的应力强度因子，对不同形式的杨氏模量和泊松比，计算了界面裂纹应力强度因子，结果表明泊松比的变化形式对应力强度因子影响不大，可当作常数处理，而杨氏模量的影响则很大。     

基于非线性弹簧界面的复合材料分层损伤预测

基于功能等效的原理,用自定义本构的非线性弹簧模拟复合材料层间界面,弹簧的刚度随着界面层的牵引力-位移曲线变化,可以表征界面材料性能的线性和非线性退化过程。对复合材料单一型分层和混合型分层损伤演化过程进行了模拟分析,研究了单元尺寸、界面强度等参数对模拟结果的影响机理。结果表明:非线性弹簧界面单元能够准确地模拟分层损伤的起始和扩展过程,使用非线性弹簧模拟界面可以减小计算模型规模,与内聚力单元相比计算效率提高约10倍;裂纹每扩展一个单元长度所需要的能量与单元尺寸成正比,单元尺寸越大,裂纹扩展所需要的能量越大;界面强度越低,初始裂纹尖端张开过程越平缓,模型的收敛性越好,可以通过降低弹簧单元界面强度来减小模型计算规模。     

拉伸荷载下分支裂隙破坏机理研究

为研究拉伸荷载下分支裂隙对破坏模式的影响,保持主裂隙参数不变,改变分支裂隙倾角和长度,利用扩展有限元方法模拟了弯折裂隙的动态扩展,总结了分支裂隙参数变化对破坏模式的影响.利用ABAQUS中的轮廓积分计算了分支裂隙尖端应力强度因子,并根据最大周向应力准则计算起裂角.结果表明:拉伸荷载下分支裂隙出现三种破坏模式;分支裂隙倾...     

无限平板内埋裂纹线弹簧模型

建立了无限平板内埋椭圆形裂纹的弹簧模型,用积分变换方法推导了问题的控制积分方程笔应力强度因子的表达式,给出了数值结果,并与现有交替迭代解进行了比较,结果表明模型的应用是合理的。     

Effect of electrical polarization saturation on stress intensity factors in a piezoelectric ceramic

The electric-field induced stress intensity factor in a piezoelectric medium of limited electrical polarization is evaluated based on a strip-saturation model of the Dugdale-type. Particular emphasis is placed on the effect of the saturation condition on the near tip field and the stress intensity factor. To this end, the general solution is derived in terms of the (unspecified) normal electrical displacement distribution along the saturated strip. Since the saturated strip is representative of the unknown saturated zone, the normal electrical displacement may suffer discontinuity across the saturated strip. It is found that the crack-tip field and the stress intensity factors depend on the discontinuity of the normal electrical displacement across the saturated strip although this dependency disappears in some practically important cases. A crack perpendicular to the poling axis in a general poled ferroelectric is discussed in detail to illustrate the implications of the strip-saturation model for electric-field induced cracking. The results show that some discrepancies between theory and experiments, for which the classical linear piezoelectric model gives qualitatively incorrect results, can be explained clearly in terms of the stress intensity factor given by the strip-saturation model. In particular, these results are independent of the form of the saturation condition imposed on the saturated strip.     

稳态循环应力下结构断裂可靠性设计方法

对含初始缺陷（宏观裂纹）结构进行无限寿命断裂可靠性设计，给出了疲劳裂纹扩展应力强度因子的二维概率密度函数及其门槛值分布函数公式，通过应力强度因子，门槛值干涉模型可求得裂纹不扩展的可靠度和指定可靠度下不扩展裂纹的最大尺寸，并确定含裂纹构件的检修周期。     

CTS试件中复合型疲劳裂纹扩展

针对复合型循环载荷作用下的金属构件中的裂纹扩展问题进行了实验分析和理论建模. 首先 采用紧凑拉剪试件(CTS)和 Richard研制的复合型载荷加载装置，对承受复合型循环载荷的裂纹进行了实验研究. 实验选择了两种金属材料试件，分别承受3种形式的复合型循环载荷的作用，在裂纹尖端具 有相同的初始应力场强度的条件下考察复合型循环载荷对裂纹扩展规律的影响. 实验结果表明，疲劳裂纹的扩展速率与加载角度有关. 对于同样金属材料的试件，当裂尖处 初始应力场强度相等时，载荷越接近于II型，裂纹增长速率越快. 采用等效应力强度 因子(I型和II型应力强度因子的组合)、裂纹扩展速率及复合强度等参数，以实验数据为 基础，建立了一个疲劳裂纹扩展模型，用来预测裂纹在不同模式疲劳载荷作用下的扩展速率. 为验证其有效性，该模型被应用于钢制试件的数值模拟计算中. 实验结果与模拟计算曲线保 持一致，表明该模型可以用来估算带裂纹金属构件的寿命.     

A micromechanical model for predicting the fracture toughness of functionally graded foams

In this paper, finite element method based micromechanical analysis is used to understand the fracture behavior of functionally graded foams. The finite element analysis uses a micro-mechanical model in conjunction with a macro-mechanical model in order to relate the stress intensity factor to the stresses in the struts of the foam. The stress intensity factor at the crack tip of the macro-mechanical model can be evaluated using either the J-contour integral or the stresses in the singularity-dominated zone. The fracture toughness is evaluated for various crack positions and length within the functionally graded foam. Then the relationship between the fracture toughness of the graded foam and the local density at the crack tip is studied. Convergence tests for both macro-mechanical and micro-mechanical model analysis were conducted in order to maintain adequate accuracy with reasonable computational time. Fracture toughness of homogenous foams and functionally graded foams for various cases are presented as a function of relative density. This study indicates that the fracture toughness of functionally graded foams mainly depends on the relative density at the crack-tip.     

A penny-shaped crack in a filament-reinforced matrix—II. The crack problem

Using the filament model developed in the previous paper, the elastostatic interaction problem between a penny-shaped crack and a slender inclusion or filament in an elastic matrix is formulated. For a single filament as well as multiple identical filaments located symmetrically around the crack the problem is shown to reduce to a singular integral equation. The solution of the problem is obtained for various geometries and filament to-matrix stiffness ratios, and the results relating to the angular variation of the stress intensity factor and the maximum filament stress are presented.     

Modelling of Unsteady Transition in Low-Pressure Turbine Blade Flows with Two Dynamic Intermittency Equations

A transition model for describing wake-induced transition is presented based on the SST turbulence model by Menter and two dynamic equations for intermittency: one for near-wall intermittency and one for free-stream intermittency. In the Navier-Stokes equations, the total intermittency factor, which is the sum of the two, multiplies the turbulent viscosity computed by the turbulence model. The quality of the transition model is illustrated on the T106A test cascade for two Reynolds numbers, using experimental results by Stieger and Hodson for transition mainly due to kinematic wake impact on a separation bubble. The quality of the model is also revealed on the T106D test cascade using experimental results from Hilgenfeld, Stadtmuller and Fottner for wake turbulence induced transition. The test cases differ in pitch to chord ratio, Reynolds number and inlet free-stream turbulence intensity, causing different transition mechanisms. The unsteady results are presented in space-time diagrams of shape factor and wall shear stress on the suction side. The results show the capability of the model to capture the physics of unsteady transition in separated state. Inevitable shortcomings are revealed as well.     

Two-dimensional fractal-like finite element method for thermoelastic crack analysis

The fractal-like finite element method has been proved to be very efficient and accurate in two-dimensional static and dynamic crack problems. In this paper, we extend our previous study to include the thermal effect for two-dimensional isotropic thermal crack problems. Both the temperature intensity factor and thermal stress intensity factor can be calculated directly. The temperature distribution is first found, which is imposed thereafter as a thermal load in the elastic problem. The transformation function used in the study has been found analytically. The effects of different thermal loading on the thermal stress intensity factor are presented. The numerical examples are compared with the results from other methods and find to be in good agreement.     

压电薄板板边导电裂纹尖端的力电场分析

采用有限元方法，分析了压电薄板板边不同长度导电裂纹尖端的力电场分布规律，发现导电裂纹尖端的应力场和电场强度存在明显的集中和奇异现象，集中和奇异的程度与裂纹长度有关。而且，在裂纹延长线上分别存在两点，这里的应力和电场对裂纹长度不太敏感，总等于无裂纹时薄板的均匀应力和均匀电场强度；同时，还研究了导电裂纹尖端的应力强度因子和电场强度因子对裂纹长度的依赖关系，发现在线性本构的前提下，导电裂纹尖端的应力强度因子与电场强度因子之间具有近似的线性关系。