钇和镧掺杂氧化铝陶瓷的热导及其介电弛豫特性研究

采用氧化物固相反应法,制备出纯氧化铝陶瓷及其分别掺杂稀土元素钇和镧的陶瓷样品.测量了样品的结构、介电特性和热导性能;研究了烧结温度对掺杂不同稀土元素的陶瓷样品的性能的影响.X射线衍射结果表明1500℃烧结后陶瓷样品形成了单一的固溶体.而氧化铝的热导率达到8.60W/（m·K）,样品的介电性能稳定.我们发现掺杂Y³⁺和La³⁺的氧化铝陶瓷存在介电弛豫现象,并对该现象进行了机理分析.     

CaCu3Ti4O12陶瓷的介电特性与弛豫机理

本文采用Novocontrol宽频介电谱仪在-100 ℃–100 ℃温 度范围内、0.1 Hz–10 MHz频率范围内测量了表面层打磨前 后CaCu₃Ti₄O₁₂陶瓷的介电特性, 分析了CaCu₃Ti₄O₁₂陶瓷的介电弛豫机理. 首先, 基于对宏观“壳-心”结构的定量分析, 排除了巨介电常数起源于表面层效应的可能性; 其次, 基于经典Maxwell-Wagner夹层极化及其活化能物理本质的分析, 排除了巨介电常数起源于经典Maxwell-Wagner极化的可能性; 最后, 依据晶界Schottky势垒与本征点缺陷的本质联系, 提出了巨介电常数起源于Schottky势垒边界陷阱电子弛豫的新机理. 陷阱电子弛豫机理反映了CaCu₃Ti₄O₁₂陶瓷本征点缺陷、 电导、介电常数之间的本质关系. 关键词： 3Ti₄O₁₂')" href="#">CaCu₃Ti₄O₁₂ 介电弛豫 Schottky势垒 点缺陷     

Fe离子注入多晶Al2O3的光电子能谱研究

本文应用光电子能谱(XPS)方法分析Fe离子注入多晶Al₂O₃样品中各离子的存在状态。通过微机对谱峰进行高斯拟合处理,得出注入离子Fe不同价态的相对含量。 关键词：     

巨介电常数氧化物CaCu3Ti4O12的介电和阻抗特性

采用固相烧结法合成了单相巨介电常数氧化物CaCu₃Ti₄O₁₂（CCTO）.用阻抗分析仪分析了10—420 K温度范围内的介电频谱和阻抗谱特性,并结合ZVIEW软件进行了模拟.结果表明：温度高于室温时,频谱出现两个明显的弛豫台阶,低频弛豫介电常数随温度升高而显著增大,表现出热离子极化特点;温度低于室温时,频谱表现出类德拜弛豫,且高、低平台介电常数值基本不随温度变化,表现出界面极化特点和较好的温度稳定性.频谱中依次出现的介电弛豫对应于阻抗谱中 关键词： 3Ti₄O₁₂')" href="#">CaCu₃Ti₄O₁₂ 介电频谱 阻抗谱 Cole-Cole半圆弧     

MoO3/Al2O3催化剂中Mo分散的正电子研究

用浸渍法制备了一系列不同Mo含量的MoO₃/Al₂O₃催化剂.测量了这些样品的正电子湮没寿命谱(PALS)与符合多普勒展宽(CDB)谱,以研究其孔洞结构以及Mo分散.正电子寿命测量结果表明,Al₂O₃载体中存在两种不同尺寸的孔洞.掺入MoO₃之后,Mo原子主要进入Al₂O₃的大孔中,使孔洞体积减小.符合多普勒展宽谱结果表明,当MoO 关键词： 3/Al₂O₃催化剂')" href="#">MoO₃/Al₂O₃催化剂 正电子湮没寿命谱 符合多普勒展宽 Mo 分散     

退火对Pb辐照Al2O3单晶发光特性的影响

研究了230MeV的²⁰⁸Pb²⁷⁺辐照Al₂O₃样品及随后在600,900,1100K高温条件下退火后的光致发光特性。从辐照样品的测试结果可以清楚地看到在波长为390,450nm处出现了强的发光峰。辐照量为1×10¹³ions/cm²时,样品的发光峰最强。经过600K退火2h后测试结果显示,380nm发光峰剧烈增强,而其他发光峰显示不明显。在900K退火条件下,380nm的发光峰开始减弱,而在360,510nm出现了明显的发光峰,至到1100K退火完毕后380nm的发光峰完全消失,而360,510nm的发光峰相对增强。从被辐照样品的FTIR谱中看到,波数在460~510cm^-1间的吸收是振动模式,经过离子辐照后,吸收带展宽,随着辐照量的增大,Al₂O₃振动吸收峰消失,说明Al₂O₃振动模式被完全破坏。1000~1300cm^-1之间为Al—O—Al桥氧的伸缩振动模式,辐照后吸收带向高波数方向移动,说明其振动模式受到影响。辐照剂量较小的样品,损伤程度相对较低,经退火晶化后,振动模式基本恢复到单晶状态;辐照剂量较高的样品,损伤程度大,退火处理后表面变得较粗糙,振动模式并未出现,说明结构破坏严重。     

脉冲形成线用CaO-TiO2-Al2O3基介质陶瓷介电性能

设计了一种脉冲形成线用新型CaO-TiO2-Al2O3基介质陶瓷体系,采用传统固相法通过优化组分和制备工艺,调控材料的微结构,获得了介电性能优异的介质陶瓷。其介电常数在15~35之间可调,介电损耗小于0.002,频率稳定性好。在厚度为1 mm时,介电强度高达50 kV/mm。研究了厚度对CaO-TiO2-Al2O3基介质陶瓷介电强度的影响规律,当厚度从1 mm减小到0.1 mm时,介电强度呈非线性增大,从50 kV/mm（1 mm厚样品）提高到92 kV/mm（0.1 mm厚样品）,可见,CaO-TiO2-Al2O3基介质陶瓷的电击穿与其机械损坏具有相似性。结合CaO-TiO2-Al2O3基介质陶瓷的化学组分和微观结构,CaO-TiO2-Al2O3基介质陶瓷优越的电击穿特性可以用弱点击穿理论解释。     

12CaO·7Al2O3/5CaO·3Al2O3：Sm3+新型红色荧光粉的制备及发光性质

采用自蔓延燃烧法制备了不同Sm³⁺掺杂浓度的12CaO·7Al₂O₃（C12A7：x%Sm³⁺）荧光粉。在404 nm近紫外光激发下,观察到了位于565,599,648 nm附近的3个光发射峰,分别归属于Sm³⁺的⁴G_5/2→⁶H_J/2（J=5,7,9）能级跃迁。随着Sm³⁺掺杂浓度增加,红光发射强度呈现了先增大后减小的规律,优化的Sm³⁺掺杂摩尔分数为1.5%,发光的浓度猝灭效应可归因于Sm³⁺之间发生了交叉弛豫过程。采取混相策略,通过降低初始粉体的煅烧温度至900℃获得了12CaO·7Al₂O₃/5CaO·3Al₂O₃：1.5%Sm³⁺（C12A7/C5A3：Sm³⁺）混相荧光粉,进一步提高了红光发射强度。利用变温光致发光谱计算得到混相样品的热激活能约为200 meV,结果表明该混相荧光粉具有良好的热稳定性。     

脉冲形成线用CaO-TiO2-Al2O3基介质陶瓷介电性能

设计了一种脉冲形成线用新型CaO-TiO2-Al2O3基介质陶瓷体系,采用传统固相法通过优化组分和制备工艺,调控材料的微结构,获得了介电性能优异的介质陶瓷。其介电常数在15~35之间可调,介电损耗小于0.002,频率稳定性好。在厚度为1 mm时,介电强度高达50 kV/mm。研究了厚度对CaO-TiO2-Al2O3基介质陶瓷介电强度的影响规律,当厚度从1 mm减小到0.1 mm时,介电强度呈非线性增大,从50 kV/mm（1 mm厚样品）提高到92 kV/mm（0.1 mm厚样品）,可见,CaO-TiO2-Al2O3基介质陶瓷的电击穿与其机械损坏具有相似性。结合CaO-TiO2-Al2O3基介质陶瓷的化学组分和微观结构,CaO-TiO2-Al2O3基介质陶瓷优越的电击穿特性可以用弱点击穿理论解释。     

Cr4+在Al2O3多晶体中的光谱性能研究

采用传统无压烧结工艺制备Cr:Al₂O₃透明多晶陶瓷.测定了其退火前后的吸收光谱和荧光光谱，发现在Al₂O₃六配位的八面体结构中，Cr⁴⁺的荧光发射也处在1100—1600nm波段的红外区间，荧光发射峰位于1223nm附近，类似Cr⁴⁺在四面体中的发光行为.同时由于氧化铝晶格常数较小，晶体场强较强，使Cr⁴⁺:Al₂O_{3< 关键词： 4+')" href="#">Cr⁴⁺ 2}O₃透明陶瓷')" href="#">Cr:Al₂O₃透明陶瓷 光谱性质 八面体     

Mg，Ti共掺Al2O3透明多晶陶瓷光谱性能研究

采用传统无压烧结工艺制备Mg，Ti共掺透明氧化铝陶瓷，测定了其吸收光谱、荧光光谱和激发光谱，结果表明，由于Mg²⁺的电荷补偿，当Ti掺入量较小时，Ti主要以Ti⁴⁺形式存在，(Mg，Ti):Al₂O₃透明陶瓷只在250nm的紫外波段有吸收峰，为O^2-→Ti⁴⁺的电荷转移跃迁产生的吸收，并产生Ti⁴⁺离子在280—290nm和410—420nm的荧光发射峰     

Chemical quenching of positronium in Fe2O3/Al2O3 catalysts

Fe₂O₃/Al₂O₃ catalysts were prepared by solid state reaction method using α-Fe₂O₃ and γ-Al₂O₃ nano powders. The microstructure and surface properties of the catalyst were studied using positron lifetime and coincidence Doppler broadening annihilation radiation measurements. The positron lifetime spectrum shows four components. The two long lifetimes τ₃ and τ₄ are attributed to positronium annihilation in two types of pores distributed inside Al₂O₃ grain and between the grains, respectively. With increasing Fe₂O₃ content from 3 wt% to 40 wt%, the lifetime τ₃ keeps nearly unchanged, while the longest lifetime τ₄ shows decrease from 96 ns to 64 ns. Its intensity decreases drastically from 24% to less than 8%. The Doppler broadening S parameter shows also a continuous decrease. Further analysis of the Doppler broadening spectra reveals a decrease in the p-Ps intensity with increasing Fe₂O₃ content, which rules out the possibility of spin-conversion of positronium. Therefore the decrease of τ₄ is most probably due to the chemical quenching reaction of positronium with Fe ions on the surface of the large pores.     

Dielectric and impedance measurements on (1−x)Ba(Fe1/2Ta1/2)O3-xBa(Zn1/3Ta2/3)O3 ceramics

In this work, ((1−x)Ba(Fe_1/2Ta_1/2)O₃-xBa(Zn_1/3Ta_2/3)O₃), ((1−x)BFT-xBZT) ceramics with x = 0.00–0.12 were synthesized by the solid–state reaction method. X-ray diffraction data revealed that both the powders and ceramics were of a pure-phase cubic perovskite structure. All ceramics showed large dielectric constants. For the x = 0.12 sample, a very high dielectric constant (>20,600) was observed. A lowering in the dielectric loss compared to pure BFT ceramics was observed with the BZT addition. The impedance measurements indicated that BZT has a strong effect on the bulk grain and grain boundary resistance of BFT ceramics. These results are in agreement with the measured dielectric properties. Based on dielectric and impedance results, (1−x)BFT-xBZT ceramics could be of great interest for high performance dielectric materials applications due their giant dielectric constant behavior.     

In situ Raman spectroscopy of phase transformation in CrOx-Y2O3 system at elevated temperatures

A CrO_x-Y₂O₃ sample was prepared by a deposition-precipitation method and phase transformation of the sample under N₂ and air atmospheres was characterized by in situ Raman spectroscopy and X-ray diffraction (XRD) techniques. It was found that when the CrO_x-Y₂O₃ sample was heated, CrO₃ transformed to YCrO₄ and then to YCrO₃ and Cr₂O₃. Also, the transformation started from the surface region of the sample and then extended to the bulk, due to the fact that the phase transformation was detected by Raman spectroscopy at lower temperature compared to that by XRD. In addition, both atmosphere and temperature had influence on the phase transformation in the surface region, while the phase transformation in the bulk was merely dependent on the temperature. It was also found that low oxidation state Cr(III) species on the surface could be re-oxidized to high oxidation state Cr(V) or Cr(VI) species when the thermal treated sample was exposed to ambient air.     

Farinfrared absorption in Al2O3 and MgO

Far-infrared absorption measurements performed in Al₂O₃ and MgO between 300 and 1 500 K with a Fourier scanning interferometer are reported. A temperature analysis of results based on a phonon self-energy model allows to assign the absorption in this region to 2- and 3-phonon difference processes. The contributions of these processes are separated and discussed. In Al₂O₃, the frequency dependence of the absorption is also analyzed. A good overall agreement between theory and experiment is evidenced.     

Effects of CeO2-ZrO2 present in Pd/Al2O3 catalysts on the redox behavior of PdOx and their combustion activity

The ceria-zirconium-modified alumina-supported palladium catalysts are prepared using impregnation method with H₂PdCl₄ as Pd source, hydrazine hydrate as reducing agent. The physicochemical properties of these catalysts are characterized by BET surface area (BET), X-ray powder diffraction (XRD), transmission electron microscopy (TEM), temperature programmed reduction (H₂-TPR) and temperature programmed oxidation (O₂-TPO) techniques, and their catalytic activities for the combustion of methane are examined. The results show that the palladium mainly exist in a highly dispersed PdO species on Ce-Zr-rich grains as well as Al₂O₃-rich grains surfaces, and a stable PdO species due to the strong interaction between PdO and CeO₂-ZrO₂ on the Ce-Zr/Al₂O₃ surfaces. The catalytic activity is strongly related to the redox behavior of PdO species highly dispersed on Ce-Zr-rich grains and Al₂O₃-rich grains surfaces, and the higher the reducibility of the PdO species, the higher the catalytic activity. The presence of Ce-Zr in Pd/Al₂O₃ catalyst would inhibit the site growth of PdO_x particles and decomposition of PdO to Pd⁰, and the reoxidation property of Pd⁰ to PdO_x is significantly improved, which obviously increases thermal stability and catalytic activity of Pd/Ce-Zr/Al₂O₃ catalyst for the methane combustion.     

Preparation and wear resistance of pulse electrodeposited Ni-W/Al2O3 composite coatings

The aim of this work is to obtain the electroplating parameters for preparation of Ni-W/Al₂O₃ composite coating with high tungsten content, high micro-hardness and excellent wear resistance by pulse plating procedure. Our results showed that the duty cycle is a dominant parameter for the tungsten content in the coating and the tungsten content increases significantly with increasing duty cycle. The further analysis showed the great influence of tungsten content on micro-hardness of the coating. A maximum micro-hardness of about 859 Hv was obtained in pulse electrodeposited Ni-W/Al₂O₃ composite with tungsten content of 40 wt.% at a peak current density of 20 A/dm², a duty cycle of 80%, a pulse frequency of 1000 Hz and a particle loading of 10 g/L alumina in the plating bath. Although the hardness of Ni-W/Al₂O₃ composite coating was only slightly affected by the alumina content of the deposits prepared in present investigation, the alumina content effect on the tribological characteristic of Ni-W/Al₂O₃ composite coatings is significant. The friction coefficient was lowered to 0.25 and the wear loss was reduced to 1.05 mg by setting the control factors according to the values mentioned above for obtaining the coating with the highest micro-hardness.     

Y掺杂Al2O3高k栅介质薄膜的制备及性能研究

利用射频反应共溅射方法制备了Y掺杂Al₂O₃电介质薄膜，用掠入射x射线衍射检测了薄膜的结构，用高分辨率扫描电子显微镜(HRSEM)、原子力显微镜(AFM)观察了薄膜断面和表面形貌，用高频C-V和变频C-V及J-V测量了样品的电学特性. 结果表明，Y的掺入使电介质薄膜的介电常数k有了很大提高(8.14—11.8)，并体现出了较好的介电特性. 分析认为：与氧具有较大电负性差的Y离子的加入，增大了薄膜中的金属—氧键(M—O)的强度；同时，Y的加入使Al₂O₃的结构和原子配位发生了改变，从而提高了离子极化对薄膜介电常数的贡献. 退火前后的XRD谱均显示薄膜为非晶态；HRSEM断面和AFM形貌像显示所制备的薄膜非常平整，能够满足器件要求. 关键词： 高k栅介质 掺杂氧化铝 射频反应溅射     

Interfacial reactions and oxidation behavior of Al2O3 and Al2O3/Al coatings on an orthorhombic Ti2AlNb alloy

The uniform and dense Al₂O₃ and Al₂O₃/Al coatings were deposited on an orthorhombic Ti₂AlNb alloy by filtered arc ion plating. The interfacial reactions of the Al₂O₃/Ti₂AlNb and Al₂O₃/Al/Ti₂AlNb specimens after vacuum annealing at 750 °C were studied. In the Al₂O₃/Ti₂AlNb specimens, the Al₂O₃ coating decomposed significantly due to reaction between the Al₂O₃ coating and the O-Ti₂AlNb substrate. In the Al₂O₃/Al/Ti₂AlNb specimens, a γ-TiAl layer and an Nb-rich zone came into being by interdiffusion between the Al layer and the O-Ti₂AlNb substrate. The γ-TiAl layer is chemically compatible with Al₂O₃, with no decomposition of Al₂O₃ being detected. No internal oxidation or oxygen and nitrogen dissolution zone was observed in the O-Ti₂AlNb alloy. The Al₂O₃/Al/Ti₂AlNb specimens exhibited excellent oxidation resistance at 750 °C.