Nanoscale hydrophobic recovery: A chemical force microscopy study of UV/ozone-treated cross-linked poly(dimethylsiloxane)

Chemical force microscopy (CFM) in water was used to map the surface hydrophobicity of UV/ozone-treated poly(dimethylsiloxane) (PDMS; Sylgard 184) as a function of the storage/recovery time. In addition to CFM pull-off force mapping, we applied indentation mapping to probe the changes in the normalized modulus. These experiments were complemented by results on surface properties assessed on the micrometer scale by X-ray photoelectron spectroscopy and water contact-angle measurements. Exposure times of < or = 30 min resulted in laterally homogeneously oxidized surfaces, which are characterized by an increased modulus and a high segmental mobility of PDMS. As detected on a sub-50-nm level, the subsequent "hydrophobic recovery" was characterized by a gradual increase in the pull-off forces and a decrease in the normalized modulus, approaching the values of unexposed PDMS after 8-50 days. Lateral imaging on briefly exposed PDMS showed the appearance of liquid PDMS in the form of droplets with an increasing recovery time. Longer exposure times (60 min) led to the formation of a hydrophilic silica-like surface layer. Under these conditions, a gradual surface reconstruction within the silica-like layer occurred with time after exposure, where a hydrophilic SiOx-enriched phase formed < 100-nm-sized domains, surrounded by a more hydrophobic matrix with lower normalized modulus. These results provide new insights into the lateral homogeneity of oxidized PDMS with a resolution in the sub-50-nm range.     

The stability of radio-frequency plasma-treated polydimethylsiloxane surfaces

Polydimethylsiloxane (PDMS) is a widely used material for manufacturing lab-on-chip devices. However, the hydrophobic nature of PDMS is a disadvantage in microfluidic systems. To transform the hydrophobic PDMS surface to hydrophilic, it was treated with radio-frequency (RF) air plasma at 150, 300, and 500 mTorr pressures for up to 30 min. Following the surface treatment, the PDMS specimens were stored in air, deionized water, or 0.14 M NaCl solution at 4 degrees C, 20 degrees C, and 70 degrees C. The change in the hydrophilicity (wettability) of the PDMS surfaces was followed by contact angle measurements and Fourier transform infrared attenuated total reflectance (FTIR-ATR) spectroscopy as a function of time. As an effect of the RF plasma treatment, the contact angles measured on PDMS surfaces dropped from 113 +/- 4 degrees to 9 +/- 3 degrees . The chamber pressure and the treatment time had no or negligible effect on the results. However, the PDMS surface gradually lost its hydrophilic properties in time. The rate of this process is influenced by the difference in the dielectric constants of the PDMS and its ambient environment. It was the smallest at low temperatures in deionized water and largest at high temperatures in air. Apparently, the OH groups generated on the PDMS surface during the plasma treatment tended toward a more hydrophilic/less hydrophobic environment during the relaxation processes. The correlation between the FTIR-ATR spectral information and the contact angle data supports this interpretation.     

Development of Water-Repellent Glass Improved Water-Sliding Property and Durability

A water-repellent glass with high water-sliding property using FAS for the hydrophobic material has been developed. It had been thought that the sliding property of FAS was inferior to PDMS. But it was found that the sliding angles of the surfaces coated with FAS were affected by coating condition. And the glass on which fluorinated alkyl groups oriented toward normal direction of the surface had almost equal water-sliding property to the one coated with PDMS. Furthermore its durability against wiper abrasion and outside weathering was much higher than that with PDMS. And XPS analysis was carried out to confirm the orientation of fluorinated alkyl groups on the developed water-repellent glass. This kind of water-repellent glass was adopted as commercial automotive windows.     

Wettability control and patterning of PDMS using UV-ozone and water immersion

We demonstrate a simple method to tune and pattern the wettability of polydimethylsiloxane (PDMS) to generate microfluidic mimics of heterogeneous porous media. This technique allows one to tailor the capillary forces at different regions within the PDMS channel to mimic multi-phase flow in oil reservoirs. In this method, UV-ozone treatment is utilized to oxidize and hydrophilize the surface of PDMS. To maintain a stable surface wettability, the oxidized surfaces are immersed in water. Additionally, the use of a photomask makes it convenient to pattern the wettability in the porous media. A one-dimensional diffusive reaction model is established to understand the UV-ozone oxidation as well as hydrophobic recovery of oxidized PDMS surfaces. The modeling results show that during UV-ozone, surface oxidation dominates over diffusion of low-molecular-weight (LMW) species. However, the diffusivity of LMW species plays an important role in wettability control of PDMS surfaces.     

Hydrophilic surface modification of polydimetylsiloxane‐co‐2‐hydroxyethylmethacrylate (PDMS‐HEMA) by Silwet L‐77 (heptamethyltrisiloxane) surface treatment

Biomaterials and their host organism's quintessential place of interaction are the surfaces of materials, as transportation of liquids within microchannels requires hydrophilic surfaces. Modifying the hydrophobic surface of polydimethylsiloxane (PDMS) into a hydrophilic one which can be used in biomaterials remains a big challenge. Herein, PDMS‐hydroxyethylmethacrylate (HEMA) films were prepared by the condensation of PDMS using isophorone diisocyanate as a cross‐linker, followed by the incorporation of HEMA via radical copolymerization. The as‐prepared PDMS‐HEMA films were thereafter hydrophilized via physical treatment with heptamethyltrisiloxane. The surface properties of the obtained PDMS‐HEMA films were characterized in wettability, morphology, topography, swelling, mechanical properties, and protein adsorption. Compared to pristine PDMS‐HEMA as control, the surface wettability, roughness, and protein adsorption of the hydrophilized PDMS‐HEMA films were significantly improved while the films also exhibited excellent optical properties. However, the improvement of the swelling properties remains insignificant, indicating that the interior morphology was still based on the hydrophobic siloxane PDMS. The long‐term hydrophilicity was considered good as no significant hydrophobic recovery was noticeable in a period of 5 months after treatment.     

Surface functionalization of silicone rubber for permanent adhesion improvement

The surface properties of poly(dimethyl siloxane) (PDMS) layers screen printed onto silicon wafers were studied after oxygen and ammonia plasma treatments and subsequent grafting of poly(ethylene -alt-maleic anhydride) (PEMA) using X-ray photoelectron spectroscopy (XPS), roughness analysis, and contact angle and electrokinetic measurements. In the case of oxygen-plasma-treated PDMS, a hydrophilic, brittle, silica-like surface layer containing reactive silanol groups was obtained. These surfaces indicate a strong tendency for "hydrophobic recovery" due to the surface segregation of low-molecular-weight PDMS species. The ammonia plasma treatment of PDMS resulted in the generation of amino-functional surface groups and the formation of a weak boundary layer that could be washed off by polar liquids. To avoid the loss of the plasma modification effect and to achieve stabilization of the mechanically instable, functionalized PDMS top layer, PEMA was subsequently grafted directly or after using gamma-APS as a coupling agent on the plasma-activated PDMS surfaces. In this way, long-time stable surface functionalization of PDMS was obtained. The reactivity of the PEMA-coated PDMS surface caused by the availability of anhydride groups could be controlled by the number of amino functional surface groups of the PDMS surface necessary for the covalent binding of PEMA. The higher the number of amino functional surface groups available for the grafting-to procedure, the lower the hydrophilicity and hence the lower the reactivity of the PEMA-coated PDMS surface. Additionally, pull-off tests were applied to estimate the effect of surface modification on the adhesion between the silicone rubber and an epoxy resin.     

Surface restructuring behavior of various types of poly(dimethylsiloxane) in water detected by SFG

Surface structures of several different poly(dimethylsiloxane) (PDMS) materials, tetraethoxysilane-cured hydroxy-terminated PDMS (TEOS-PDMS), platinum-cured vinyl-terminated PDMS (Pt-PDMS), platinum-cured vinyl-terminated poly(diphenylsiloxane)-co-poly(dimethylsiloxane) (PDPS-co-PDMS), and PDMS-co-polystyrene (PDMS-co-PS) copolymer in air and water have been investigated by sum frequency generation (SFG) vibrational spectroscopy. The SFG spectra collected from all PDMS surfaces in both air and water are dominated by methyl group stretches, indicating that all the surfaces are mainly covered by methyl groups. Other than surface-dominating methyl groups, some -Si-CH2-CH2- moieties on the Pt-PDMS surface have also been detected in air, which are present at cross-linking points. Information about the average orientation angle and angle distribution of the methyl groups on the PDMS surface has been evaluated. Surface restructuring of the methyl groups has been observed for all PDMS surfaces in water. Upon contacting water, the methyl groups on all PDMS surfaces tilt more toward the surface. The detailed restructuring behaviors of several PDMS surfaces in water and the effects of molecular weight on restructuring behaviors have been investigated. For comparison, in addition to air and water, surface structures of PDMS materials mentioned above in a nonpolar solvent, FC-75, have also been studied. By comparing the different response of phenyl groups to water on both PDPS-co-PDMS and PS-co-PDMS surfaces, we have demonstrated how the restructuring behaviors of surface phenyl groups are affected by the structural flexibility of the molecular chains where they are attached.     

Hydrophobization of glass surface by adsorption of poly(dimethylsiloxane)

Silica or glass particles are introduced in a poly(dimethylsiloxane) (PDMS) matrix for various applications. A particular feature of these systems is that PDMS adsorbs on the surface of the dispersed particles, thus rendering them more hydrophobic with time. The mechanism of this process of in situ hydrophobization is still poorly understood. The major aims of the present study are (1) to quantify the rate of surface hydrophobization by PDMS and, on this basis, to discuss the mechanism of the process; (2) to compare the contact angles of surfaces that are hydrophobized by different procedures and are placed in contact with different fluid interfaces-PDMS-water, hexadecane-water, and air-water; and (3) to check how the type of surfactant affects the contact angles, viz., the effective hydrophobicity of the surface. We present experimental results for the kinetics of hydrophobization of glass surfaces, which are characterized by measuring the three-phase contact angle of glass-surfactant solution-PDMS. The data reveal two consecutive stages in the hydrophobization process: The first stage is relatively fast and the contact angle increases from 0 degrees to about 90 degrees within several minutes. This stage is explained with the physical adsorption of the PDMS chains, as a result of hydrogen-bond formation with the surface silanol groups. The second stage is much slower and hours or days are required at room temperature to reach the final contact angle (typically, 150-160 degrees). This stage is explained as grafting of the PDMS molecules on the surface by chemical reaction with the surface silanol groups. If the glass surface had been pretreated by hexamethyldisilazane (HMDS), so that CH(3) groups had blocked most of the surface silanol groups, the first stage in the hydrophobization process is almost missing-the contact angle slowly changes at room temperature from about 90 degrees up to 120 degrees. The experiments aimed to compare several hydrophobization procedures showed that PDMS ensures larger contact angle (more hydrophobic surface) than grafted alkyl chains. The contact angles at the PDMS-water and hexadecane-water interfaces were found to be very similar to each other, and much larger than that at the air-water interface. Interestingly, we found that the ionic surfactants practically do not affect the contact angle of PDMS-hydrophobized surface, whereas the nonionic surfactants reduce this angle. Similar trends are expected with silica surfaces, as well.     

Stability of various silicone oil/water emulsion films as a function of surfactant and salt concentration

There have been reports, originally by the Bristol group, and subsequently by others, of the preparation and properties of emulsions of stable, nearly monodisperse droplets of poly(dimethylsiloxane) (PDMS) in water, where no added surfactant is used. It has been assumed that their stability is due to the high density of surface-ionized hydroxyl groups, similar in fact to the closely related St?ber silica particles. In this study we confirm, from droplet lifetime studies, that droplets, prepared from such synthesized PDMS, are significantly more stable to coalescence than similar-sized droplets prepared from three types of commercially available PDMS, containing HO-, MeO-, or Me3-terminated chains, respectively. It is shown, however, that the zeta potentials of the synthesized PDMS and of the various commercial oils are all very similar (as indeed are their Hamaker constants). So some other explanation must be inferred for the enhanced stability to coalescence of the synthesized PDMS droplets compared to the commercial PDMS droplets. It is shown, for droplets formed from n-hexane and the synthesized oil, that stability to coalescence is conferred at PDMS volume fractions (phiPDMS) around 0.2 in the mixture. The synthesized PDMS is known to consist of mixtures of cyclic PDMS and short-chain linear species, with terminal -OH groups. There is some (indirect) evidence that in the interval 0.25 < phiPDMS < 0.35, the linear PDMS chains may be adsorbed close to a monolayer at the mixed oil/water interface, possibly conferring some enhanced Gibbs elasticity to the interface. This underpins the possibility that, in the synthesized oil droplets themselves, there is also preferential adsorption of the linear chains at the PDMS/water interface, and this leads to a value of the Gibbs elasticity, sufficient to significantly reduce coalescence. Unfortunately, the Gibbs elasticity could not be measured in this case. However, such preferential adsorption is unlikely to occur with the commercial PDMS oils, which are not so heterogeneous. Finally, it is shown that droplets of the three commercial PDMS oils could be stabilized against coalescence, if a sufficient, minimum amount of sodium dodecyl sulfate (SDS) is added. Gibbs elasticity values have been estimated in these cases, from plots of interfacial tension against ln(SDS concentration).     

Simultaneous tuning of chemical composition and topography of copolymer surfaces: micelles as building blocks.

A simple method is described for controlling the surface chemical composition and topography of the diblock copolymer poly(styrene)-b-poly(dimethylsiloxane)(PS-b-PDMS) by casting the copolymer solutions from solvents with different selectivities. The surface morphology and chemical composition were characterized by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS), respectively, and the wetting behavior was studied by water contact angle (CA) and sliding angle (SA) and by CA hysteresis. Chemical composition and morphology of the surface depend on solvent properties, humidity of the air, solution concentration, and block lengths. If the copolymer is cast from a common solvent, the resultant surface is hydrophobic, with a flat morphology, and dominated by PDMS on the air side. From a PDMS-selective solvent, the surface topography depends on the morphology of the micelles. Starlike micelles give rise to a featureless surface nearly completely covered by PDMS, while crew-cut-like micelles lead to a rough surface with a hierarchical structure that consists partly of PDMS. From a PS-selective solvent, however, surface segregation of PDMS was restricted, and the surface morphology can be controlled by vapor-induced phase separation. On the basis of the tunable surface roughness and PDMS concentration on the air side, water repellency of the copolymer surface could be tailored from hydrophobic to superhydrophobic. In addition, reversible switching behavior between hydrophobic and superhydrophobic can be achieved by exposing the surface to solvents with different selectivities.     

Surface modification and aging studies of addition-curing silicone rubbers by oxygen plasma

Poly(dimethyl siloxane) (PDMS) has been focused on recently due to its variety of applications specifically in microsystems technology. Many companies market two-component PDMS, which is comprised of a base component and a curing agent. Widely known and used for microsystems applications is Sylgard 184 from Dow Corning. Present work deals with two-component Room Temperature Vulcanized (RTV) PDMS from three different companies. They are Sylgard 184 from Dow Corning, RTV 615 from GE Silicones and RTV 141 from Rhodia Chemicals. Temporary increase in wettability of these three different types of PDMS by oxygen plasma by varying the plasma power and exposure time has been studied and compared with results available in literature. The hydrophobic recovery of the modified surfaces was monitored as a function of time and quantified. The surfaces were characterized using contact angle measurements and ATR-FTIR and XPS spectroscopy, their behavior analyzed in term of free surface energy and work of adhesion.     

Reverse hydrophobic PDMS surface to hydrophilic by 1‐step hydrolysis reaction

Hydrophilic modification on the surface of polymer polydimethylsiloxane (PDMS) material is a key step for its application in biomaterial, bioengineering, and so on. In this article, a novel and effective method was proposed to reverse hydrophobic surface to hydrophilic by 1‐step hydrolysis of Si―O bond to produce hydrophilic hydroxyl group. The hydrophilizing reagent 2‐(trimethylsiloxy) ethyl methacrylate (TMSEMA) was used during the copolymerization of polydimethylsiloxane prepolymer (DMS U21). The prepared PDMS film was subjected to 1‐step surface hydrophilic reversal treatment using KOH solution to produce hydroxyl groups on the surface. The contact angle, attenuated total reflection Fourier transform infrared spectra, and equilibrium water content (EWC) measurements were conducted on PDMS films. The results showed that TMSEMA content had no obvious impact on the contact angle and EWC value of untreated PDMS. After reversal treatment, the contact angle decreased from 94° to 15°, and the EWC value increases to 10% when the TMSEMA content was 15 wt%. The spectrum proved that the reverse reaction produced hydroxyl and carboxylate on the surface. The hydrophilic stability, surface morphology, and protein adsorption properties of PDMS film were also investigated. This study can provide new ideas and further reference for improving the hydrophilicity of PDMS surface.     

Response Surface Optimisation of Polydimethylsiloxane (PDMS) on Borosilicate Glass and Stainless Steel (SS316) to Increase Hydrophobicity

Particle deposition on the surface of a drying chamber is the main drawback in the spray drying process, reducing product recovery and affecting the quality of the product. In view of this, the potential application of chemical surface modification to produce a hydrophobic surface that reduces the powder adhesion (biofouling) on the wall of the drying chamber is investigated in this study. A hydrophobic polydimethylsiloxane (PDMS) solution was used in the vertical dipping method at room temperature to determine the optimum coating parameters on borosilicate glass and stainless steel substrates, which were used to mimic the wall surface of the drying chamber, to achieve highly hydrophobic surfaces. A single-factor experiment was used to define the range of the PDMS concentration and treatment duration using the Response Surface Methodology (RSM). The Central Composite Rotatable Design (CCRD) was used to study the effects of the concentration of the PDMS solution (X₁, %) and the treatment duration (X₂, h) on the contact angle of the substrates (°), which reflected the hydrophobicity of the surface. A three-dimensional response surface was constructed to examine the influence of the PDMS concentration and treatment duration on contact angle readings, which serve as an indicator of the surface’s hydrophobic characteristics. Based on the optimisation study, the PDMS coating for the borosilicate glass achieved an optimum contact angle of 99.33° through the combination of a PDMS concentration of X₁ = 1% (w/v) and treatment time of X₂ = 4.94 h, while the PDMS coating for the stainless steel substrate achieved an optimum contact angle of 98.31° with a PDMS concentration of X₁ = 1% (w/v) and treatment time of X₂ = 1 h. Additionally, the infrared spectra identified several new peaks that appeared on the PDMS-treated surfaces, which represented the presence of Si-O-Si, Si-CH₃, CH₂, and CH₃ functional groups for the substrates coated with PDMS. Furthermore, the surface morphology analysis using the Field Emission Scanning Electron Microscopy (FESEM) showed the presence of significant roughness and a uniform nanostructure on the surface of the PDMS-treated substrates, which indicates the reduction in wettability and the potential effect of unwanted biofouling on the spray drying chamber. The application of PDMS and PTFE on the optimally coated substrates successfully reduced the amount of full cream milk particles that adhered to the surface. The low surface energy of the treated surface (19–27 mJ/m²) and the slightly higher surface tension of the full cream milk (54–59 mJ/m²) resulted in a high contact angle (102–103°) and reduced the adhesion work on the treated substrates (41–46 mJ/m²) as compared to the native substrates.     

On the surface modification of microchannels for microcapillary electrophoresis chips

This paper presents systematic investigation of the microchannel surface properties in microCE chips. Three popular materials for microCE chips, polydimethylsiloxane (PDMS), quartz, and glass, are used. The zeta potentials of these microchannels are calculated by measuring the EOF velocity to evaluate the surface properties after surface modification. The hydrophobic PDMS is usually plasma-treated for microCE applications. In this study, a new method using a high-throughput atmospheric plasma generator is adopted to treat the PDMS surface under atmospheric conditions. In this approach, the cost and time for surface treatment can be significantly reduced compared with the conventional vacuum plasma generator method. Experimental results indicate that new functional groups could be formed on the PDMS surface after treatment, resulting in a change in the surface property. The time-dependent surface property of the plasma-treated PDMS is then measured in terms of the zeta potential. Results show that the surface property will reach a stable condition after 1 h of plasma treatment. For glass CE chips, two new methods for changing the microchannel surface properties are developed. Instead of using complicated and time-consuming chemical silanization procedures for CE channel surface modification, two simple and reliable methods utilizing organic-based spin-on-glass and water-soluble acrylic resin are reported. The proposed method provides a fast batch process for controlling the surface properties of glass-based CE channels. The proposed methods are evaluated using PhiX-174 DNA maker separation. The experimental data show that the surface property is modified and separation efficiency greatly improved. In addition, the long-term stability of both coatings is verified in this study. The methods proposed in this study show potential as an excellent solution for glass-based microCE chip surface modification.     

Modification of micro-channel filling flow by poly(dimethylsiloxane) surface functionalization with fluorine—Substituted aminonaphthols

Microfluidics based on the capillarity-induced filling of elastomeric channels by a suitable liquid or solution represents a useful route for realizing portable diagnostic devices designed without additional mechanical or electrical micropumps. In this study, an elastomeric mold made of poly(dimethylsiloxane) (PDMS), containing relief patterns placed in intimate contact with a silicon substrate, is utilized to create a continuous network of rectangular micro-channels for the motion of water fluid. The immobilization on activated PDMS surface of suitable functional molecules such as hydrophilic and hydrophobic fluorine-containing aminonaphthols, obtained through a straightforward and versatile synthetic procedure, allowed us to modulate PDMS surface properties depending on the structural characteristics of the employed derivative. In this context, the incorporation of fluorine groups is important for improving biocompatibility of the resulting device, providing surfaces that could be chemically and biologically inert as well as resistant to surface adhesion phenomena. The functionalization from liquid phase of PDMS replicas, involving a covalent derivatization via silanization reaction of the above mentioned compounds to an oxidized PDMS surface, resulted in a successful modification of microfluidic motion of water in rectangular capillaries, moreover contact angle values evidence also how wettability of PDMS films could be modulated, with the fluorinated aminonaphthols fuctionalized PDMS exhibiting higher contact angles.     

Surface modification for PDMS-based microfluidic devices

This review focuses on advances reported from April 2009 to May 2011 in PDMS surface modifications for the application in microfluidic devices. PDMS surface modification techniques presented here include improved plasma and graft polymer coating, dynamic surfactant treatment, hydrosilylation-based surface modification and surface modification with nanomaterials such as carbon nanotubes and metal nanoparticles. Recent efforts to generate topographical and chemical patterns on PDMS are also discussed. The described surface modifications not only increase PDMS wettability, inhibit or reduce non-specific adsorption of hydrophobic species onto the surfaces in the act, but also result in the display of desired functional groups useful for molecular separations, biomolecular detection via immunoassays, cell culture and emulsion formation.     

CF4 plasma treatment of poly(dimethylsiloxane): effect of fillers and its application to high-aspect-ratio UV embossing

Surface modification of poly(dimethylsiloxane) (PDMS) was carried out via CF4 plasma treatment. The test PDMS used contains significant amounts of quartz and silica fillers, while the control material is the same PDMS with quartz removed by centrifugation. Fluorination accompanied with roughening was produced on both PDMS surfaces. With short plasma times (15 min or less), a macromolecular fluorocarbon layer was formed on the PDMS surfaces because of the dominant fluorination, leading to significant increase in F concentration, decrease of surface energy, and some roughening. With intermediate plasma times (15-30 min), dynamic balance between fluorination and ablation was achieved, leading to a plateau of the surface roughness, fluorine content, and [F-Si]/[F-C] ratio. At our longest investigated plasma time of 45 min, the plasma ablated the fluorinated covering layer on the PDMS surfaces, leading to significant increase in roughness and [F-Si]/[F-C] ratio and decrease of surface F concentration. The effect of additional quartz in the test PDMS on surface F concentration, [F-Si]/[F-C] ratio, and roughness was dramatic only when ablation was significant (i.e., 45 min). The obtained Teflon-like surface displays long-term stability as opposed to hydrophobic recovery of other plasma-treated PDMS surfaces to increase hydrophilicity. On the basis of the optimized plasma treatment time of 15 min, a microstructured PDMS mold was plasma treated and successfully used for multiple high-aspect-ratio (about 8) UV embossing of nonpolar polypropylene glycol diacrylate (PPGDA) resin.     

聚二甲基硅氧烷/微纳米银/聚多巴胺修饰的超疏水海绵的制备和应用

受海洋贝类生物黏附蛋白的启发,在碱性环境下利用多巴胺的自聚合性质,在聚氨酯海绵表面聚合活性聚多巴胺薄层,采用葡萄糖还原银离子进一步沉积微纳米银粒子构筑表面微纳结构,并水解聚二甲基硅氧烷前驱体对表面进行疏水改性,制备出了接触角大于150°的超疏水表面。利用接触角测定、扫描电子显微镜及能量弥散X射线谱和傅里叶红外光谱等技术手段对制备的改性海绵进行了表征,表明微纳米银粒子和硅甲基疏水基团被成功修饰到了海绵表面。改性海绵对有机溶剂和油类物质具有高选择性和高吸收性。吸收的有机溶剂和油类物质的质量能够达到其自身质量的12倍以上。饱和吸收后的海绵仅通过物理挤压即可将吸收的物质回收并使海绵恢复弹性和吸附能力,得到再生。该研究为油水分离和废油回收提供了一种经济、高效、环境友好的方案。     

Incorporation of polydimethylsiloxane into polyurethanes and characterization of copolymers

Novel copolymers of polyurethane (PU) were prepared by direct transurethanetion reaction of a commercial PU with polydimethylsiloxanes (PDMS, MW 1000, 5000, and 10,000) containing hydroxyl end-groups. Transurethanetions with different mass ratios of hydrophobic PDMS to hydrophilic PU chains (PDMS1000–PU: 43:57, 67:33, 71:29, and 80:20; PDMS5000–PU: 37:63, and 51:49; PDMS10000–PU: 51:49) were carried out in solution at 65 and 100 °C. In catalyzed reactions, dibutyltin dilaurate (SnC₃₂H₆₄O₄) was used to promote bond breaking in the PU chain and accelerate the reaction between hydroxyl end-groups of PDMS and regenerated isocyanates of PU. The chemical structures of the prepared copolymers were comprehensively characterized by ¹H, ¹³C, and ²⁹Si NMR spectroscopies. According to elemental analysis, the content of PDMS varied between 3 wt.% and 16 wt.%, and results obtained from the ¹H NMR spectroscopy were in good agreement with the results of elemental analysis. Increased length of the hydrophobic chain increased the content of PDMS in the copolymer. The GPC results showed that molar masses of the PUPDMS copolymers were lower than the molar mass of the starting PU. The glass transitions (T_g) of the copolymers were shifted to lower temperature as compared with T_g of the starting polyurethane. ATR FTIR spectroscopy showed the surface of the copolymer films to be enriched with siloxane groups and, according to electron microscopy, it was textured with microspheres. The static contact angles for copolymer films measured with deionized water ranged from 94° to 117°. The different structural, thermal and surface properties of the PUPDMS copolymers as compared with PU indicated that transurethanetion had taken place.     

超疏水性聚二甲基硅氧烷膜的制备及其表面吸附性研究

采用简单的激光刻蚀方法制备了具有类“菜花”状多级结构的粗糙聚二甲基硅氧烷(PDMS)膜, 并用CCD与高敏感性微电力学天平观察和测量PDMS表面对水的吸附情况. 结果表明, 该膜表面具有超疏水性, 同时对水滴具有超低的吸附力. 还对其表面特殊多级结构产生的机理进行了分析, 并探讨了在化学组成和表面结构对超疏水性以及吸附性产生的影响.