Preconcentration and separation of acaricides by polyether based polyurethane foam

This paper reports the preconcentration of some dissolved organic phosphorous and chlorinated acaricides in water by porous polyether based polyurethane foam. Preliminary screening tests on the retention of the tested compounds, i.e., dicofol and bromopropylate, by polyether foams indicated that a very high percent removal of the tested species was obtained. The retention rate was found fast and reaches equilibrium in a few minutes. The various parameters, e.g., pH, extraction media, shaking time, salt effect, temperature and sample volumes affecting the preconcentration of the tested species by the unloaded foam, trioctylamine and trimethylphosphate treated foam have been optimized via batch modes of separation. The unloaded foams were employed in column modes for the retention and recovery of the tested species. The sorption efficiency and recovery of the compounds by the unloaded foams column were found to be up to 97.5%. The height equivalent to a theoretical plate (HETP) obtained by the unloaded foam was found to be in the range 1.1-1.3 ± 0.2 mm. The sorption mechanism of the tested compounds by the foams was discussed.     

Luminescence determination of europium microquantities after its preconcentration on polyurethane foam

Sorption of the mixed-ligand complexes of europium(III) with thenoyltrifluoroacetone (TTA) and 1,10-phenanthroline (Phen) on polyurethane foam (PUF) has been studied by a luminescence method. The optimum conditions of sorption have been found. The sorbate composition on PUF has been determined (the Eu:TTA:Phen ratio was 1:3:1). Luminescence spectra of the europium complexes in solution and on PUF at 77 K have been investigated. It was concluded that the character of the Eu³⁺ coordination both in solution and on the sorbent is the same. Stability constants for the complexes in solution (lg K = 8.4) and on the sorbent (lg K = 5.5) have been calculated. The decrease of the stability of the complex on PUF is explained by the deformation of the complex molecule in the sorbent phase. Sorption coefficients for europium (245) and scandium (2.35) and the coefficient of selectivity for europium in Sc₂O₃ (102.3) have been determined. A method for the sorption-luminescence determination of europium in Sc₂O₃ with a lower limit of contents determined of 1 × 10⁻⁶⁰% has been developed.     

Preconcentration and separation of iron, zinc, cadmium and mercury, from waste water using Nile blue a grafted polyurethane foam

The present work describes a novel method for the incorporation of Nile blue A into polyurethane foam matrix. This foam material was found to be very suitable for the extraction of metal ions from aqueous solutions. The characterization of Nile blue A grafted foam and the effect of halide concentration, pH, shaking time, extraction isotherm and capacity have been investigated. This foam material was found to be suitable for the separation and preconcentration of iron (III), zinc (II), cadmium (II) and mercury (II) from waste water. The extraction was accomplished in (15-20) minutes. Iron was separated from acid medium (2-4 M HCl), zinc from (3-5 M HCl), cadmium from (4-6 M HCl) as thiocyanate complexes and mercury was separated from (1-2 M HCl) as chloride.     

Chromotropic acid-functionalized polyurethane foam: A new sorbent for on-line preconcentration and determination of cobalt and nickel in lettuce samples

A chromotropic acid-functionalized polyurethane foam has been developed for use in an on-line preconcentration system for cobalt and nickel determination. The packing material was prepared by covalent coupling of chromotropic acid with the polyurethane foam through an azo group. Co and Ni ions were sorbed in the mini-column, from which they could be eluted directly to the nebulizer-burner system of a flame atomic absorption spectrometer. Elution of cobalt and nickel from the mini-column can be accomplished with 0.50 and 0.75 M HCl solutions, respectively. The enrichment factors obtained were 22 (Co) and 27 (Ni), for 60 s preconcentration time, and 57 (Co) and 59 (Ni), if a preconcentration time of 180 s was used. Under the optimum conditions, the proposed procedure allowed the determination of metals with detection limits of 0.43 (cobalt) and 0.52 microg/L (nickel), respectively, on using preconcentration periods of 180 s. The accuracy of the developed procedure was evaluated by analysis of the certified reference materials NIST 1515 Apple Leaves and NIST 1570a Spinach Leaves. The method was applied to the analysis of lettuce samples. The contents of cobalt in the samples analyzed varied from 0.75 to 0.98 microg/g. Nickel was not detected in the lettuce samples.     

Chemical enrichment and separation of uranyl ions in aqueous media using novel polyurethane foam chemically grafted with different basic dyestuff sorbents

The new type of the grafted polyurethane foam sorbents were prepared by coupling polyether polyol, toluene diisocyanate and basic dyestuff (Methylene blue, Rhodamine B and Brilliant green). The Me.B-PUF, Rh.B-PUF and Br.G-PUF were characterized using UV/vis, IR and TGA. The adsorption properties and chromatographic behaviour of these new adsorbents for preconcentration and separation of uranium(VI) ions at low concentrations from aqueous thiocyanate media were investigated by a batch process. The maximum sorption of U(VI) was in the pH ranges 1-4. The kinetics of sorption of the U(VI) by the Grafted-PUF were found to be fast with half life of sorption (t_1/2) in 2.43 min. The average sorption capacity of different sorbents 0.124 meq g⁻¹ for uranyl ions, enrichment factors ≈40 and the recovery 98-100% were achieved (R.S.D. ≈ 0.73%). The basic dyestuff Grafted-PUF could be used many times without decreasing their capacities significantly. The value of the Gibbs free energy (ΔG) for the sorbents is −7.3 kJ mol⁻¹, which reflects the spontaneous nature of sorption process. The sorption mechanism of the metal ion onto Grafted-PUF was also discussed.     

The chromatographic behavior of group (IIB) metal ions on polyurethane foam functionalized with 8-hydroxyquinoline

Polyurethane foam functionalized with 8-hydroxyquinoline has been prepared by coupling the foam matrix with 8-hydroxyquinoline (oxine) through an azo spacer. The oxine-bonded foam (Ox PUF) was characterized by use of different tools (UV–Vis spectra, IR spectra, density, and stability). Ox PUF was found to be very suitable for separation and preconcentration of trace metals, e.g. Zn(II), Cd(II), and Hg(II) ions, from wastewater in the pH ranges 2–12, 9–12, and 3–6, respectively. Various conditions influencing the sorption of these metal ions on to Ox PUF were optimized. Extraction of the metal ions was accomplished in 15 to 20 min. Study of the variation of the sorption of the tested metal ions with temperature yielded average values for H, S, and G of 41.99, 158.23, and –5.1 kJ mol^–1, respectively. The capacities of the foam material were 0.27, 0.16, and 0.09 mmol g^–1 for Zn(II), Cd(II), and Hg(II), respectively. Preconcentration factors >50 were achieved (RSD6.18). The quantitative results were obtained from experiments performed using certified reference materials.     

Preparation,characterization and applications of polyurethane foam functionalized with resorcinol for quantitative separation and determination of silver(I) and mercury(II) from tap and wastewater

A stable chelating resin matrix was prepared by covalently linking resorcinol with polyurethane foam matrix through a –N=N– group. Preconcentration and determination of trace Ag⁺ and Hg²⁺ ions from samples of different origin, using Res-PUF, were studied. Various conditions influencing the sorption of these metal ions onto Res-PUF were optimized. The kinetics of sorption of the Ag⁺ and Hg²⁺ by Res-PUF were found to be fast, reached equilibrium in few minutes (5–10?min) and followed a first-order rate equation with an overall rate constant k in 0.102 and 0.267/min, respectively. Study of the variation of the sorption of the tested metal ions with temperature yielded average values for ΔG, ΔH and ΔS of ?3.94, ?22.02 and ?58.37, respectively. The mean free sorption energy (E) computed from the Dubinin–Radushkevich (D–R) isotherm was found to be equal to 8.91 kJ/mol, which reflects the chelation sorption process. The capacities of the foam material were 0.15 and 0.07?mmol/g for Ag⁺ and Hg²⁺, respectively. Preconcentration factors of?>?50 were achieved (RSD?≈?5.99). The proposed preconcentration procedure was applied successfully to the determination of trace metal ions in natural and wastewater samples.     

The determination of molybdenum in water and biological samples by graphite furnace atomic spectrometry after polyurethane foam column separation and preconcentration

A system for molybdenum separation and enrichment aiming its determination in water and biological samples by graphite furnace atomic absorption spectrometry (GFAAS) is proposed. The procedure is based on the sorption of the molybdenum (VI) thiocyanate complex onto a mini-column packed with polyurethane foam (PUF). The elution is accomplished by a 3.0 mol l⁻¹ nitric acid solution. Flow variables were optimized and an enrichment factor of 10 as well as a limit of detection (LOD) (3 s) of 0.08 μg l⁻¹ in the sample solution were achieved. The coefficient of variation showed values of 3 and 2% for molybdenum solutions of 2.0 and 10.0 μg l⁻¹, respectively. The accuracy of the method was confirmed by the good concordance between found and certified values in the analysis of certified reference materials (CRMs) (CASS-3 Nearshore Seawater, NIST 1547 Peach Leaves, NIST 1515 Apple Leaves and NIST 1572 Citrus Leaves). The procedure was also applied for the molybdenum determination in mineral waters as well as in produced water samples. The results obtained for the mineral water samples compared well with those obtained by ICP-MS. Concerning the produced water samples, in spite of their large salinity, recoveries of 90 to 120% at the 1 μg l⁻¹ were observed.     

Retention, kinetics and thermodynamics profile of cadmium adsorption from iodide medium onto polyurethane foam and its separation from zinc bulk

The sorption behaviour of 2.5 × 10⁻⁵ M solution of Cd(II) on polyurethane foam (PUF) from iodide medium have been investigated. The conditions were optimized from aqueous solutions of different pH (1-10) and of acids of varied concentration (0.01-1.0 M). The maximum concentration of KI was found to be 0.24 M and equilibration time was established to be 20 min. The data successfully followed the Freundlich and Dubinin-Radushkevich (D-R) isotherms at low metal ion concentration while Langmuir isotherm followed at higher metal ion concentration. The Freundlich parameter 1/n = 0.66 ± 0.02 have been evaluated whereas D-R isotherm yields the sorption free energy E = 10.5 ± 0.1 kJ mol⁻¹ indicating ion exchange type chemisorption. The monolayer coverage (XL) constant of Langmuir isotherm was found to be 23.7 ± 0.4 mg g⁻¹. The numerical values of thermodynamics parameters enthalpy (ΔH), entropy (ΔS) and Gibbs free energy (ΔG) indicated the endothermic and spontaneous nature of sorption. The Scatchard plot analysis was tested to evaluate the binding sites of the PUF and stability constants of sorption were determined. On the basis of these parameters, the sorption mechanism was discussed. Among the foreign ions tested, Pb(II), Hg(II), cyanide and nitrite should be absent. The clean separation of Cd(II) from Zn(II) ions in the ratio 1:250, respectively, was achieved by column chromatography.     

Quantitative separation of zinc traces from cadmium matrices by solid-phase extraction with polyurethane foam

A system for separation of zinc traces from large amounts of cadmium is proposed in this paper. It is based on the solid-phase extraction of the zinc in the form of thiocyanate complexes by the polyurethane foam. The following parameters were studied: effect of pH and of the thiocyanate concentration on the zinc extraction, shaking time required for quantitative extraction, amount of PU foam necessary for complete extraction, conditions for the separation of zinc from cadmium, influence of other cations and anions on the zinc sorption by PU foam, and required conditions for back extraction of zinc from the PU foam. The results show that zinc traces can be separated from large amounts of cadmium at pH 3.0±0.50, with the range of thiocyanate concentration from 0.15 to 0.20 mol l⁻¹, and the shaking time of 5 min. The back extraction of zinc can be done by shaking it with water for 10 min. Calcium, barium, strontium, magnesium, aluminum, nickel and iron(II) are efficiently separated. Iron(III), copper(II) and cobalt(II) are extracted simultaneously with zinc, but the iron reduction with ascorbic acid and the use of citrate to mask copper(II) and cobalt(II) increase the selectivity of the zinc extraction. The anions nitrate, chloride, sulfate, acetate, thiosulphate, tartarate, oxalate, fluoride, citrate, and carbonate do not affect the zinc extraction. Phosphate and EDTA must be absent. The method proposed was applied to determine zinc in cadmium salts using 4-(2-pyridylazo)-resorcinol (PAR) as a spectrophotometric reagent. The result achieved did not show significant difference in the accuracy and precision (95% confidence level) with those obtained by ICP–AES analysis.     

X-ray fluorescence spectrometric determination of germanium after extraction with polyurethane foam

Germanium is extracted onto polyurethane foam as molybdogermanate, and determined by X-ray fluorescence spectrometry in the dried foam. The extraction is effective between pH 0.5 and 3.7 and as little as 7 μg of germanium can be detected in 100 ml of aqueous solution.     

Separation and determination of trace amounts of zinc, lead, cadmium and mercury in tap and Qaroun lake water using polyurethane foam functionalized with 4-hydroxytoluene and 4-hydroxyacetophenone

A stable chelating sorbent was synthesized by covalently linking 4-hydroxytoluene or 4-hydroxyacetophenone with the polyurethane foam (PUF) through -NN- group. The synthesized chelating sorbents were characterized by IR and UV/vis measurements. The modified foams show excellent stability towards various solvents. Factors influencing the extraction process of Zn(II), Pb(II), Cd(II) and Hg(II) were studied and evaluated as a function of pH of metal ion solution and equilibration shaking time. The values of sorption capacity of metal ions (μg g⁻¹) were determined with the two types of bonded foams. The two phenolic bonded foams were studied comparatively. The potential applications of the two newly synthesized foams for the removal and separation of the examined metal ions from two natural water samples (drinking tap water and Qaroun lake water at Fayoum City, Egypt) were investigated. Precision (assessed as a relative standard deviation, R.S.D.) was also evaluated and found to be ≤7.3% (N = 5) with a detection limit under 0.46 μg L⁻¹.     

Separation and determination of some trivalent metal ions using rhodamine B grafted polyurethane foam

The incorporation of rhodamine B into polyurethane foam matrix was prepared by mixing the rhodamine B with polyol (polyether) prior to the addition of diisocyanate reagent to form the polyurethane foam material. Rhodamine B grafted polyurethane foam (Rod.B-PUF) was found to be very suitable for the separation and preconcentration of trivalent metal ions e.g. bismuth (III), antimony (III) and iron (III) from thiocyanate solutions. Bismuth and antimony were separated from concentrated acid medium (1–6 M H₂SO₄). Iron (III) was separated from pH 1 to 3. The kinetics of sorption of the Bi (III), Sb (III) and Fe (III) onto the Rod.B-PUF was found to be fast, the extraction is accomplished from 5 to 10 min with average values of half-life of sorption (t_1/2) of 2.9 min. The average values of the Gibbs free energy (ΔG) for the sorption of metal ions onto Rod.B-PUF are ?6.6 kJ mol^?1, which reflect the spontaneous nature of sorption process. The sorption mechanism of the metal ion onto Rod.B-PUF was also discussed.     

Retention and separation of some organic water pollutants with unloaded and tri-n-octylamine loaded polyester-based polyurethane foams

The analytical utility of unloaded and polyester-based polyurethane loaded foams with tri-n-octylamine (TOA) in the removal of some phenols from water were carried out. In static mode, the TOA-loaded foams showed a good affinity of extraction towards the tested compounds as compared to the untreated foams. The various parameters affecting the retention efficiency of the tested compounds from aqueous media by the foam were examined via batch technique. The TOA-loaded foams were employed in column modes for the extraction and recovery of the tested phenols. The retention efficiency and the recovery of the tested compounds from the loaded foam column were up to 98.5%. Sorption of the compounds by the foam were brought by solvent extraction mechanism. The molecular weight and the pK(a) of the compounds play an important role in the extraction process. The height equivalent to a theoretical plate (HETP) of the TOA-foam column was found in the range 1.8-2.05 +/- 0.1 mm at flow-rates up to 10 cm(3)/min. Separation of some of the tested phenols was also carried out by the TOA-foam columns. The membrane properties of the polyester foam sorbents give unique advantages over conventional granular sorbents in rapid, versatile and effective separations and preconcentrations of the tested compounds.     

Magnetic nanomaterials for the removal,separation and preconcentration of organic and inorganic pollutants at trace levels and their practical applications: A review

The presence of organic and inorganic pollutants in nature even in very small concentrations threatens human and other living bodies health and makes it significant to remove, separate and preconcentrate these pollutants. Recently magnetic nano sorbents has been used frequently in the separation and preconcentration of these pollutants. The use of magnetic nano sorbents modified with inorganic and organic species has widespread applications in the solid phase extraction (SPE) studies due to its many unique properties. These modified nano sorbents are preferred due to their advantages such as high adsorption capacities and large surface areas. This review examined different types of magnetic materials such as magnetic carbon-based nano sorbents, inorganic nano sorbents with magnetic properties, magnetized biosorbents, magnetic metal-organic frameworks, and magnetized ionic liquids used in SPE studies. In this study, a comprehensive and systematic review of the separation and preconcentration of analytes such as heavy metal ions, drug active substances, pesticides, dyes, hormone disruptors, etc with SPE methods using magnetic nanomaterials has been revealed. Future aspects and challenges that may be encountered are discussed.     

On-line preconcentration system using a minicolumn of polyurethane foam loaded with Me-BTABr for zinc determination by Flame Atomic Absorption Spectrometry

In the present paper, an on-line system for preconcentration and determination of zinc by Flame Atomic Absorption Spectrometry (FAAS) is proposed. It is based in the sorption of zinc(II) ions on a minicolumn packed with polyurethane foam loaded with 2-[2′-(6-methyl-benzothiazolylazo)]-4-bromophenol (Me-BTABr) reagent. Chemical and flow variables as pH effect, sample flow rate and eluent concentration were optimized using univariate methodology. The results demonstrated that zinc can determinate using the sample pH in the range of 6.5-9.2, sample flow rate of 6.0 ml min⁻¹, and the elution step using 0.10 mol l⁻¹ hydrochloric acid solution at flow rate of 5.5 ml min⁻¹. In these conditions, an enrichment factor of 23 and a sampling rate of 48 samples per hour were achieved. The detection limit (DL, 3σ) as IUPAC recommendation was 0.37 μg l⁻¹ and the precision (assessed as the relative standard deviation, R.S.D.) reached values of 5.9-1.8% in zinc solutions of 1.0-10.0 μg l⁻¹ concentration, respectively. The method was successfully applied to the determination of trace amounts of zinc in natural water samples from Salvador (Brazil).     

Preparation and properties of negative ion/polyurethane flexible foam composites

Abstract

In this study, negative ionpowder was modified with a silane coupling agent and then added to the polyurethane flexible foam to prepare NI/PU flexible foam composites by the one-step foaming method. The effects of the amount of negative ion powder on the mechanical properties, thermal properties and release of negative ions were investigated using scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and negative ion detectors. The SEM results showed that modified negative ion powder could be more uniformly distributed around the cell walls of the polyurethane flexible foam. The thermal stability, tensile strength and resilience of the NI/PU flexible foam composite were improved with the increase of the amount of modified negative ion powder. Increasing the amount of modified negative ion powder could also result in an increase in the release of negative ions, and it reached 5500/cm³ or higher at a negative ion content of 3%.     

Preparation of novel ion exchange polyurethane foam and its application for separation and determination of palladium in environmental samples

The new strong anion exchanger (PUFIX) from polyurethane foam was prepared by coupling of the primary amine of the foam matrix with ethyl iodide. PUFIX was characterized using different tools (IR spectra, elemental analysis, density and thermal analysis). The sorption properties of the new anion exchanger (PUFIX) and chromatographic behaviour for separation and determination of palladium(II) ions at low concentrations from aqueous iodide or thiocyanate media were investigated by a batch and dynamic processes. The maximum sorption of Pd(II) was in the pH range of 0.3–2. The kinetics of sorption of the Pd(II) by the PUFIX was found to be fast with average values of half-life of sorption (t_1/2) of 3.32 min. The variation of the sorption of Pd(II) with temperature gives average values of ΔH, ΔS, ΔG and ΔE to be −38.3 kJ mol⁻¹, −100.7 J K⁻¹ mol⁻¹, −8.3 and 11.8 kJ mol⁻¹, respectively. The sorption capacity of PUFIX was 1.69 mmol g⁻¹ for Pd(II), preconcentration factors of values ≈250 and the recovery 99–100% were achieved (R.S.D. ≈ 1.24%). The lower detection limit, 1.28 ng mL⁻¹ was evaluated using spectrophotometric method (R.S.D. ≈ 2.46%).     

Preconcentration and separation of Cr(III) and Cr(VI) using sawdust as a sorbent

A simple, inexpensive method based on solid-phase extraction (SPE) on sawdust from Cedrus deodera has been developed for speciation of Cr(III) and Cr(VI) in environmental water samples. Because different exchange capacities were observed for the two forms of chromium at different pH—Cr(III) was selectively retained at pH 3 to 4 whereas Cr(VI) was retained at pH 1—complete separation of the two forms of chromium is possible. Retained species were eluted with 2.5 mL 0.1 mol L⁻¹ HCl and 0.1 mol L⁻¹ NaOH. Detection limits of 0.05 and 0.04 μg mL⁻¹ were achieved for Cr(III) and Cr(VI), respectively, with enrichment factors of 100 and 80. Recovery was quantitative using 250 mL sample volume for Cr(III) and 200 mL for Cr(VI). Different kinetic and thermodynamic properties that affect sorption of the chromium species on the sawdust were also determined. Metal ion concentration was measured as the Cr(VI)–diphenylcarbazide complex by UV–visible spectroscopy. The method was successfully applied for speciation of chromium in environmental and industrial water samples.