基于荧蒽荧光熄灭的苦味酸荧光敏感膜的研究

本文基于苦味酸水溶液对固定于增塑的PVC膜中荧蒽的可逆荧光熄灭作用,研制了测定苦味酸浓度的荧光敏感膜.该膜的最佳组成为1～6mg荧蒽,50mgPVC粉, 100mg邻苯二甲酸二异辛酯.在1.50mol·L^-^1硫酸测试底液中,此膜测定苦味酸的浓度范围为1.78×10^-^6～1.28×10^-^3mol·L^-^1,重现性良好,响应时间小于30s.该法选择性好,许多常见亲脂阴离子不干扰测定.将该法用于药物辛可宁的间接测定, 结果令人满意     

Development of an alcohol optode membrane based on fluorescence enhancement of fluorescein derivatives

A new type of optode membrane for the determination of alcohols, such as methanol, ethanol, propan-1-ol and propan-2-ol etc, is presented that can be exploited in optical and fibre-optic sensors. It is based on the use of a new lipophilic fluorescent reagent, namely fluorescein octadecyl ester (FODE), which is immobilized in a plasticized PVC membrane. The response mechanism relies on the fact that FODE can reversibly recognize alcohol molecules due to the hydrogen bonding formation between FODE and alcohol molecules. The analytical information in this membrane is the enhancement of the relative fluorescence intensity measured at 527 nm (463 nm, excitation). Under the optimum condition, the membrane has a wide measuring range for alcohol samples. The membrane has been applied to determine the concentration of ethanol in alcoholic drinks with satisfactory results.     

Picric acid sensitive optode based on a fluorescence carrier covalently bound to membrane

An acryloyl group was attached to fluorescein through the phenol hydroxyl group to make it photopolymerizable with 2-hydroxypropyl methacrylate and covalently immobilized on an optode glass surface modified with gamma-(methacryloxy)propyltrimethoxysilane. The optode system with a plastic-clad fused silica bifurcated fiber optic bundle shows satisfactory analytical performance characteristics for determining picric acid in terms of selectivity and reproducibility with a linear range from 8.0 x 10(-7) to 4.0 x 10(-3) mol L-1. The quenching mechanism was investigated. The optode membrane can be applied to the indirect determination of cinchonine drug and the results obtained were satisfactory.     

A reversible optode membrane for picric acid based on the fluorescence quenching of pyrene

Pyrene immobilized in plasticized poly(vinyl chloride) (PVC) membrane is able to extract selectively picric acid from the sample solution into the organic membrane phase. Since this extraction equilibrium is accompanied by a change in the fluorescence spectrum of pyrene, the chemical recognition process can be directly translated into an optical signal. With the optode membrane described, picric acid in sample solutions from 8.7 x 10(-6) to 4.3 x 10(-3)M can be determined. The calibration curve of the optode membrane for picric acid shows a good correlation with the mathematically derived formalism and thus confirms the theoretically expected behaviour. Besides a high reproducibility of the optical signals, the very short response times less than 35 sec are realized. The optode membrane presented exhibits good selectivity for picric acid over many other usual hydrophobic anions.     

Detection of DNA based on fluorescence resonance energy transfer of polyelectrolyte-protected CdTe quantum dots as energy donors

The approach for DNA detection was established by using a fluorescence resonance energy transfer (FRET) system, in which the energy donor was poly-diallyldimethylammonium chloride-protected quantum dots and the energy receptor was ethidium bromide (EB) inserting into the double stranded DNA. The concentration of the probe DNA, EB and NaCl was optimized. Under the optimized conditions, the FRET system has a stable signal and good reproducibility. The linear range is 7.7-61.6 nM with the correlation coefficient of 0.998 and the limit of detection is 7.7 nM. This method is simple and sensitive, and makes the label-free DNA detection come true.     

Detection of pollen flavonoids by fluorescence on impregnated papers

Summary Limits of detection of some pollen flavonoids are recorded. The flavonoids were detected by aluminum, beryllium, and zirconium ions. Paper chromatography revealed dactylin and isoquercitrin to be present in extracts of orchard grass pollen. Only dactylin was found in timothy pollen extracts.

---

Zusammenfassung Die Erfassungsgrenzen der Tüpfelproben einiger Pollenflavone auf mit Aluminium-, Beryllium- und Zirkoniumsalz imprägniertem Papier werden angegeben. Papierchromatographie zeigte die Gegenwart von Dactylin und Isoquercitrin in Extrakten der Pollen vonDactylis glomerata L. an. Pollenextrakt vonPhleum pratense L. enthielt nur Dactylin.

---

Résumé Les auteurs indiquent les limites de détection de quelques flavonoïdes de pollen. Les flavonoïdes sont décelés par les ions aluminium, glucinium et zirconium. La Chromatographie sur papier a montré que la dactyline et l'isoquercitine étaient présentes dans les extraits de dactyle. Seule la dactyline a été trouvée dans les extraits de fléole des prés.

     

Detection of influenza A virus based on fluorescence resonance energy transfer from quantum dots to carbon nanotubes

In this paper, a simple and sensitive approach for H5N1 DNA detection was described based on the fluorescence resonance energy transfer (FRET) from quantum dots (QDs) to carbon nanotubes (CNTs) in a QDs-ssDNA/oxCNTs system, in which the QDs (CdTe) modified with ssDNA were used as donors. In the initial stage, with the strong interaction between ssDNA and oxCNTs, QDs fluorescence was effectively quenched. Upon the recognition of the target, the effective competitive bindings of it to QDs-ssDNA occurred, which decreased the interactions between the QDs-ssDNA and oxCNTs, leading to the recovery of the QDs fluorescence. The recovered fluorescence of QDs was linearly proportional to the concentration of the target in the range of 0.01–20 μM with a detection limit of 9.39 nM. Moreover, even a single-base mismatched target with the same concentration of target DNA can only recover a limited low fluorescence of QDs, illustrating the good anti-interference performance of this QDs-ssDNA/oxCNTs system. This FRET platform in the QDs-ssDNA/oxCNTs system was facilitated to the simple, sensitive and quantitative detection of virus nucleic acids and could have a wide range of applications in molecular diagnosis.     

Detection of DNA fragments separated by capillary electrophoresis based on their native fluorescence inside a sheath flow

A scheme for the separation and detection of native DNA fragments in capillary electrophoresis is presented. A UV laser at 275 nm excites the intrinsic fluorescence of the fragments, which is greatly enhanced at pH 2.8. To provide a compatible system, methylcellulose-based size separation is performed at the identical pH. A sheath-flow arrangement isolates the detection region from the linear polymer for a reduced background level. The performance is an order-of-magnitude enhancement in detectability over absorption detection. We also uncovered a selective degradation/ligation process at these pH conditions that may be useful as additional selectivity for DNA characterization.     

Detection of Helicobacter pylori with a nanobiosensor based on fluorescence resonance energy transfer using CdTe quantum dots

We report on a method for the sensitive determination of Helicobacter that is based on fluorescence resonance energy transfer using two oligonucleotide probes labeled with CdTe quantum dots (QDs) and 5-carboxytetramethylrhodamine (Tamra) respectively. QDs labeled with an amino-modified first oligonucleotide, and a Tamra-labeled second oligonucleotide were added to the DNA targets upon which hybridization occurred. The resulting assembly brings the Tamra fluorophore (the acceptor) and the QDs (the donor) into close proximity and causes fluorescence resonance energy transfer (FRET) to occur upon photoexcitation of the donor. In the absence of target DNA, on the other hand, the probes are not ligated, and no emission by the Tamra fluorophore is produced due to the lack of FRET. The feasibility of the method was demonstrated by the detection of a synthetic 210-mer nucleotide derived from Helicobacter on a nanomolar level. This homogeneous DNA detection scheme is simple, rapid and efficient, does not require excessive washing and separation steps, and is likely to be useful for the construction of a nanobiosensor for Helicobacter species.

Immunoassay methods based on fluorescence polarization

A review on the use of fluorescence polarization in immunoassay procedures is presented. Only the determination of low molecular-weight substances, such as therapeutic agents, drugs of abuse and hormones is considered because the measured change in fluorescence polarization depends on the molecular size of the analyte. The study emphasizes and appraises the analytical features of the methods so far proposed.     

Detection of chondroitin sulfate-binding proteins on the membrane

Chondroitin sulfate is a ubiquitous component of proteoglycans that is present both in the extracellular matrix and at the cell surface of various tissues. Until recently, chondroitin sulfate has attracted less attention than heparan sulfate and dermatan sulfate, owing to the limited number of known chondroitin sulfate-binding proteins. To determine the biological function of chondroitin sulfate, biotinylated probes were prepared and used to search for binding proteins. Chondroitin sulfates A, C, D, and E were biotinylated through either the uronic acid or the residual core peptide. Lysates from mouse Lewis lung carcinoma (3LL) cells were blotted onto a nitrocellulose membrane after sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) and the membrane was treated with the biotinylated chondroitin sulfates. Among the chondroitin sulfate variants, the E type showed the most intense bands upon visualization of the membrane with avidin-conjugated alkaline phosphatase and the appropriate substrates. The binding of chondroitin sulfate E to proteins in the cell lysate was not affected by the A, C or D variants but was reduced by treatment with dermatan sulfate. Lysates from 3LL cells were also treated with biotinylated chondroitin sulfate E and, after two-dimensional (2-D) electrophoresis and blotting, several chondroitin sulfate E-binding proteins including lamins and heterogeneous nuclear ribonucleoproteins were identified by mass spectrometry.     

A carbon dioxide sensor based on fluorescence

The optical carbon dioxide sensor is prepared by covering a pH sensor based on fluorescence with a CO₂-permeable membrane and contacting the pH-sensitive membrane with a reservoir of hydrogen carbonate. As carbon dioxide diffuses across the membrane it causes a chnage in pH which is detected by measuring the change in fluorescence from the base form of the pH-sensitive fluorescentdye. The usable range of response depends on the concentration of hydrogen carbonate in contact with the membrane. The sensor also responds to sulfide and sulfite.     

Fiber-optic biosensors based on fluorescence energy transfer

A new optical homogeneous biochemical method for the assay of glucose has been developed, based on fluorescence energy transfer between a glucose analog, dextran labeled with fluorescein isothiocyanate (FITC-dextran), and a glucose-receptor protein, Rhodamine-labeled Concanavalin A (Rh-ConA). When FITC-dextran binds to Rh-ConA in solution, and is light-activated, the FITC label transfers its absorbed energy to the Rhodamine label, which then emits light according to its own characteristic fluorescence spectrum. When glucose is added to this solution, the FITC fluorescence intensity increases as FITC-dextran is released from the Rh-ConA and is replaced by glucose. Thus it is possible to determine glucose concentrations directly from the level of FITC fluorescence.     

Amylase substrate based on fluorescence energy transfer

A fluorigenic substrate for measuring α-amylase (E.C. 3.2.1.1) activity was prepared by double labeling soluble starch with 5-(4,6-dichlorotrizain-2-yl)aminofluorescein and Procion Red MX8B. Because the absorption spectrum of Procion Red MX8B overlaps the fluorescein emission spectrum, Procion Red efficiently quenches fluorescein emission when it is closer than the critical radius for fluorescence energy transfer. When amylase catalyzes cleavage of a starch molecule between a fluorescein and a Procion Red MX8B, the distance between the two labels increases and the degree of quenching decreases. The rate at which the fluorescence intensity increases is proportional to amylase activity. To maximize the sensitivity it is critical to maximize the amount of Procion Red MX 8B coupled to the starch and to use a high-precision spectrofluorimeter which can measure a small rate of increase in fluorescence above a large constant background.     

Zinc selective chemosensor based on pyridyl-amide fluorescence

Chemosensors are developed to image zinc ions. Fluorescence enhancement due to Zn²⁺ binding is an excellent way to detect its presence. A chemosensor for Zn²⁺ based on dipicolylamine (DPA) groups connected by a pyridyl amide backbone has been synthesized. Addition of 2-chloroacetyl chloride to 2,6-diaminopyridine affords 2,6-bis(chloroethylamido)pyridine, which is converted to the sensor BADPA-P by 2,2′-dipicolylamine displacement of chlorine. This compound along with two others, the mono-DPA, ADPA-P and the benzyl in place of pyridyl, BADPA-B, present three potential Zn²⁺ sensors. It was found that BADPA-P in the presence of Zn²⁺ shows a large increase in fluorescence, whether in polar organic or aqueous environments. Its fluorescence in the presence of Cd²⁺, unlike with Zn²⁺, is not enhanced when excited at longer wavelengths. Proton NMR measurements, indicate two Zn²⁺ ions bind to BADPA-P. Also, Zn²⁺ enhances fluorescence even when other metal ions are present.     

Simultaneous determination of glycols based on fluorescence anisotropy

Simultaneous determination of non-fluorescent glycols in mixtures without separation or chemical transformation steps is described. Two methods based in the measure of fluorescence anisotropy of a probe such as fluorescein dissolved in the analyte or analyte mixtures are described. In the first method, the anisotropy spectra of pure and mixtures of analytes are used to quantitative determination (if the fluorophor concentration is in a range where fluorescence intensity is proportional to concentration). In the second method, a calibration curve anisotropy-concentration based on the application of the Perrin equation is established. The methods presented here are capable of directly resolving binary mixtures of non-fluorescent glycols on the basis of differences on the fluorescence anisotropy of a fluorescence tracer. Best analytical performances were obtained by application of the method based on Perrin equation. This method is simple, rapid and allows the determination of mixtures of glycols with reasonable accuracy and precision. Detection limits are limited by the quantum yield and anisotropy values of the tracer in the solvents. Recovery values are related to the differences in anisotropy values of the tracer in the pure solvents. Mixtures of glycerine/ethylene glycol (GL/EG), ethylene glycol/1,2-propane diol (EG/1,2-PPD) and polyethylene glycol 400/1,2-propane diol (PEG 400/1,2-PPD) were analysed and recovery values are within 95-120% in the Perrin method. Relative standard deviation are in the range 1.3-2.9% and detection limits in the range 3.9-8.9%.     

Ratiometric fluorescence detection of bleomycin based on proximity-dependent fluorescence conversion of DNA-templated silver nanoclusters

We design a ratiometric fluo rescent sensing platform for bleomycin(BLM) by using proximity-dependent DNA-templated silver nanoclusters(DNA-AgNCs) probe.This ratiometric sensing system is constructed with DNA-AgNCs as single fluorophore.The proposed strategy is based on the two following facts:(1) a covert DNA can approach and transform the DNA-AgNCs with green emission(G-DNA-AgNCs) into red emission through hybridization reaction.(2) The specific cleavage of the convert DNA by BLM in the presence of Fe(Ⅱ) inhibits the discoloration of G-DNA-AgNCs.Thus,benefiting from the specific recognition of BLM and unique properties of G-DNA-AgNCs,a hignly-sensitive ratiometric sensor for BLM has been successfully developed.The detection limit is as low as 30 pmol/L.This label-free fluorescence probe possesses advantages of convenient synthetic process and low cost.Moreover,this ratiometric method has been applied to the detection of BLM in human serum samples,illustrating a promising tool for analysis of BLM in cancer therapy.     

Enzyme catalytic membrane based on a hybrid mesoporous membrane

Immobilization of glucose oxidase (GOD) within a hybrid mesoporous membrane with 12 nm pore diameter was successfully achieved, resulting in catalytically high efficiency during flow of a glucose solution across the membrane.