A study of nano-sized surface coating on LiMn2O4 materials

The present study used the Pechini process with a heat treatment to synthesize LiMn₂O₄ powder (LMO). After surface coating, a nano-sized oxidative film of Li-Ni-Mn formed on the surface of the LMO-Ni powders. The concentration of Mn³⁺ for the LMO-Ni powder was lower and the average electrovalence of Mn exceeded the theoretical value, resulting in the initial capacity of the LMO-Ni powder being lower than the LMO powder. However, the LMO-Ni powder with the Li/Ni film not only restrained Mn ions from dissolving into the electrolyte, but also improved the charge-discharge cycling capacity.     

Effect of ultrasonic irradiation on structure and electrochemical properties of LiMn2O4 thin films cathode material for Li-ion micro-batteries

Two kinds of spinel LiMn₂O₄ thin film for lithium ion micro-batteries were successfully prepared on polycrystal Pt substrates by spin coating methods, which were carried out under ultrasonic irradiation (USG) and magnetic stirring (MSG), respectively. The microstructures and electrochemical performance of LiMn₂O₄ thin films were characterized by thermogravimetry analysis (TGA), X-ray diffraction (XRD), scanning electron microscopy (SEM), and galvanostatic charge-discharge measurements. It was found that the crystalline structure of USG samples grew better than that of the MSG samples. At the same time, higher discharge capacity and better cycle stability were obtained for the LiMn₂O₄ thin films of USG at the current density of 50 μAh/cm² between 3.0 and 4.3 V. The 1st discharge capacity was 57.8 μAh/cm²-μm for USG thin films and 51.7 μAh/cm²-μm for MSG thin films. After 50 cycles, 91.4% and 69% of discharge capacity could be retained respectively, indicating that ultrasonic irradiation condition during spin coating was more suitable for preparing spinel LiMn₂O₄ thin films with better electrode performance for lithium ion micro-batteries.     

Al掺杂的尖晶石型LiMn2O4的结构和电子性质

采用基于密度泛函理论的第一性原理方法, 在广义梯度近似(GGA)和GGA+U方法下对尖晶石型LiMn₂O₄及其Al掺杂 的尖晶石型LiAl_0.125Mn_1.875O₄晶体的结构和电子性质进行了计算. 结果表明: 采用GGA方法得到尖晶石型LiMn₂O₄是立方晶系结构, 其中的Mn离子为+3.5价, 无法解释它的Jahn-Teller 畸变. 给出的LiMn₂O₄能带结构特征也与实验结果不符. 而采用GGA+U方法得到在低温下的LiMn₂O₄和其掺杂 体系LiAl_0.125Mn_1.875O₄的晶体都是正交结构, 与实验一致. 也能明确地确定Mn的两种价态Mn³⁺/Mn⁴⁺的分布并且能够说明Mn³⁺O₆的z方向有明显的Jahn-Teller 畸变, 而Mn⁴⁺O₆则没有畸变. LiMn₂O₄的能带结构与实验比较也能够符合. 采用GGA+U方法对Al掺杂体系的LiAl_0.125Mn_1.875O₄的研究表明, 用Al替换一个Mn不会明显地改变晶体的电子性质, 但可以有效地消除Al³⁺O₆ 八面体的Jahn-Teller畸变, 从而改善正极材料LiMn₂O₄的性能, 这与电化学实验的观察结果相一致.     

Characterization and electrochemical performance of the spinel LiMn2O4 prepared from -MnO2

The preparation and characterization of the spinel LiMn₂O₄ obtained by solid state reaction from quasi-amorphous -MnO₂ is reported. A well-defined highly pure spinel was characterized from X-ray diffractograms. The average manganese valence of -MnO₂ and spinel samples was found to be 3.89±0.01 and 3.59±0.01, respectively. The electrochemical performance of the spinel was evaluated through cyclic voltammetry and chronopotentiometry. The voltammetric profiles obtained at 1 mV/s for the LiMn₂O₄ electrode in 1 M LiClO₄ dissolved in a 2:1 mixture of ethylene carbonate and dimethyl carbonate showed typical peaks for the lithium insertion/extraction reactions. The charge capacity of this electrode was found to be 110 mA h g⁻¹ for the first charge/discharge cycles.     

Surface modification of LiMn2O4 thin films at elevated temperature

In order to improve the cycle stability of spinel LiMn₂O₄ electrode at elevated temperature, the LiCoO₂-coated and Co-doped LiMn₂O₄ film were prepared by an electrostatic spray deposition (ESD) technique. LiCoO₂-coated LiMn₂O₄ film shows excellent cycling stability at 55 °C compared to pristine and Co-doped LiMn₂O₄ films. The samples were studied by X-ray diffraction, scanning electron microscopy, Auger electron spectroscopy, cyclic voltammetry and electrochemical impedance spectroscopy. The excellent performance of LiCoO₂-coated LiMn₂O₄ film can be explained by suppression of Mn dissolution. On the other hand, the LiCoO₂-layer on the LiMn₂O₄ surface allows a homogenous Li⁺ insertion/extraction during electrochemical cycles and improves its structure stability.     

Novel approach to preparation of LiMn2O4 core/LiNixMn2−xO4 shell composite

Combining two methods, coating and doping, to modify spinel LiMn₂O₄, is a novel approach we used to synthesize active material. First we coated the LiMn₂O₄ particles with the nickel oxide particles by means of homogenous precipitation, and then the nickel oxide-coated LiMn₂O₄ was calcined at 750 °C to form a LiNi_xMn_2−xO₄ shell on the surface of spinel LiMn₂O₄ particles. Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), cyclic voltammetry (CV) and charge-discharge test were performed to characterize the spinel LiMn₂O₄ before and after modification. The experimental results indicated that a spinel LiMn₂O₄ core is surrounded by a LiNi_xMn_2−xO₄ shell. The resulting composite showed excellent electrochemical cycling performance with an average fading rate of 0.014% per cycle. This improved cycle stability is greatly attributed to the suppression of Jahn-Teller distortion on the surface of spinel LiMn₂O₄ particles during cycling.     

Improvement of electrochemical performance of all-solid-state lithium secondary batteries by surface modification of LiMn2O4 positive electrode

To improve the electrochemical performance of an all-solid-state In/80Li₂S⋅20P₂S₅ (electrolyte)/LiMn₂O₄ cell, a lithium-titanate thin film was used to coat LiMn₂O₄. The interfacial resistance between LiMn₂O₄ and the electrolyte (measured after initial charging) decreased when the LiMn₂O₄ particles were coated with lithium-titanate. A cell with lithium-titanate-coated LiMn₂O₄ had a higher capacity than a cell with noncoated LiMn₂O₄ for current densities in the range 0.064 to 2.6 mA cm^− 2. Additionally, a cell with coated LiMn₂O₄ retained 96% of the 10th-cycle reversible capacity at a current density of 0.064 mA cm^− 2 after 50 cycles.     

Electrochemical behaviour of sputtered c-V2O5 and LiCoO2 thin films for solid state lithium microbatteries

Here are reported for the first time electrochemical data on all-solid-state lithium microbatteries using crystalline sputtered V₂O₅ thin films as cathode materials and LiPON as solid electrolyte. The stable specific capacity of 30 µAh/cm² found with a 2.4 µm thick film competes very well with the best values obtained for solid state microbatteries using amorphous films. With the challenge of decreasing the temperature of heat treatment for sputtered LiCoO₂ thin films, we show that a temperature of 500 °C combined with an optimized bias sputtering (-50 V) allows to get highly crystalline deposits, to minimize the presence of Co₃O₄ and to suppress any trace of the cubic phase. At the same time the theoretical specific capacity is reached in the 4.2 V-3 V range and a good cycling behaviour is achieved with a high capacity of 50 µAh/cm²/µm after 140 cycles at 10 µA.cm².     

Immobilization of glucose oxidase using CoFe2O4/SiO2 nanoparticles as carrier

Aminated-CoFe₂O₄/SiO₂ magnetic nanoparticles (NPs) were prepared from primary silica particles using modified StÖber method. Glucose oxidase (GOD) was immobilized on CoFe₂O₄/SiO₂ NPs via cross-linking with glutaraldehyde (GA). The optimal immobilization condition was achieved with 1% (v/v) GA, cross-linking time of 3 h, solution pH of 7.0 and 0.4 mg GOD (in 3.0 mg carrier). The immobilized GOD showed maximal catalytic activity at pH 6.5 and 40 °C. After immobilization, the GOD exhibited improved thermal, storage and operation stability. The immobilized GOD still maintained 80% of its initial activity after the incubation at 50 °C for 25 min, whereas free enzyme had only 20% of initial activity after the same incubation. After kept at 4 °C for 28 days, the immobilized and free enzyme retained 87% and 40% of initial activity, respectively. The immobilized GOD maintained approximately 57% of initial activity after reused 7 times. The K_M (Michaelis-Menten constant) values for immobilized GOD and free GOD were 14.6 mM and 27.1 mM, respectively.     

Comparison of magnetic properties in LixCoO2 and its decomposition products LiCo2O4 and Co3O4

Thermal stability of cathode material in the charged state is an important aspect for the safety of rechargeable batteries. It is well known that layered Li_xCoO₂ decomposes to a mixture of LiCoO₂ and Co₃O₄ at elevated temperatures. However, not many experimental evidences exist on intermediate phases those may form during the decomposition. Using magnetic measurements we show that it is possible to distinguish between the spinels LiCo₂O₄ and Co₃O₄ and thereby follow the decomposition of Li_xCoO₂. We characterize the magnetic behavior of thermally aged Li_xCoO₂ (x = 0.98, 0.76, 0.55) with increasing annealing time. Our results reveal the appearance of magnetic ordering in the thermally degraded products. The detailed analysis illustrates that the formation of Co₃O₄ is preceded by the formation of a meta stable LiCo₂O₄ phase.     

Atomic force microscopy study of surface morphology change in spinel LiMn2O4: Possibility of direct observation of Jahn-Teller instability

Surface morphology in 3.5 × 3.5 μm² area of spinel LiMn₂O₄, which is a typical cathode material for Li ion secondary batteries, is studied using an atomic force microscopy (AFM) with a conductive probe. Negative bias voltage is applied to the probe to attract Li⁺ ions toward LiMn₂O₄ surface during the AFM observation. Before applying the voltage (0 V), the whole LiMn₂O₄ surface is covered with scale-shaped grains. Under the negative voltage of 5.5 V, electric current abruptly increases, indicating Li⁺ ionic conduction. Simultaneously, part of the scale-shaped grains expand and flatten. Jahn-Teller phase transition, which is induced by the repulsive interaction between the Mn-e_g and O-2p electrons in Li accumulated layer, is proposed as a possible origin of these results.     

SrBi2Ta2O9/Bi4Ti3O12复合铁电薄膜的制备与特性研究

采用溶胶凝胶工艺在p-Si衬底上制备了SrBi₂Ta₂O₉/Bi₄Ti₃O₁₂复合铁电薄膜. 研究了SrBi₂Ta₂O₉/Bi₄Ti₃O₁₂复合薄膜的微观结构与生长行为、铁电性能和疲劳特性. 研究表明: Si衬底Bi₄Ti< 关键词： 2Ta₂O₉')" href="#">SrBi₂Ta₂O₉ 4Ti₃O₁₂')" href="#">Bi₄Ti₃O₁₂ 复合铁电薄膜 溶胶凝胶工艺     

A facile synthesis of monodisperse CoFe2O4/SiO2 nanoparticles

Aminated-CoFe₂O₄/SiO₂ magnetic nanoparticles (NPs) were prepared from primary silica particles using modified StÖber method. By optimizing the preparation conditions, monodisperse CoFe₂O₄/SiO₂ NPs with high amino groups’ density were obtained, which is necessary for enzyme immobilization. TEM confirm that the sample is a core/shell structure. These aminated-CoFe₂O₄/SiO₂ NPs have narrow size distributions with a mean size of about 60 nm. Moreover, the aminated-CoFe₂O₄/SiO₂ NPs can be easily dispersed in aqueous medium. The experimental results also show that the NPs have superparamagnetism, indicating that the aminated-CoFe₂O₄/SiO₂ NPs can be used as an effective carrier for the enzyme immobilization.     

Preparation and magnetic properties of BaFe12O19/Ni0.8Zn0.2Fe2O4 nanocomposite ferrite

Nanocomposite of hard (BaFe₁₂O₁₉)/soft ferrite (Ni_0.8Zn_0.2Fe₂O₄) have been prepared by the sol–gel process. The nanocomposite ferrite are formed when the calcining temperature is above 800 °C. It is found that the magnetic properties strongly depend on the presintering treatment and calcining temperature. The “bee waist” type hysteresis loops for samples disappear when the presintering temperature is 400 °C and the calcination temperature reaches 1100 °C owing to the exchange-coupling interaction. The remanence of BaFe₁₂O₁₉/Ni_0.8Zn_0.2Fe₂O₄ nanocomposite ferrite with the mass ratio of 5:1 is higher than a single phase ferrite. The specific saturation magnetization, remanence magnetization and coercivity are 63 emu/g, 36 emu/g and 2750 G, respectively. The exchange-coupling interaction in the BaFe₁₂O₁₉/Ni_0.8Zn_0.2Fe₂O₄ nanocomposite ferrite is discussed.     

Chemical quenching of positronium in Fe2O3/Al2O3 catalysts

Fe₂O₃/Al₂O₃ catalysts were prepared by solid state reaction method using α-Fe₂O₃ and γ-Al₂O₃ nano powders. The microstructure and surface properties of the catalyst were studied using positron lifetime and coincidence Doppler broadening annihilation radiation measurements. The positron lifetime spectrum shows four components. The two long lifetimes τ₃ and τ₄ are attributed to positronium annihilation in two types of pores distributed inside Al₂O₃ grain and between the grains, respectively. With increasing Fe₂O₃ content from 3 wt% to 40 wt%, the lifetime τ₃ keeps nearly unchanged, while the longest lifetime τ₄ shows decrease from 96 ns to 64 ns. Its intensity decreases drastically from 24% to less than 8%. The Doppler broadening S parameter shows also a continuous decrease. Further analysis of the Doppler broadening spectra reveals a decrease in the p-Ps intensity with increasing Fe₂O₃ content, which rules out the possibility of spin-conversion of positronium. Therefore the decrease of τ₄ is most probably due to the chemical quenching reaction of positronium with Fe ions on the surface of the large pores.     

Influence of postdeposition annealing on structural properties and electrical characteristics of thin Tm2O3 and Tm2Ti2O7 dielectrics

We describe the structural properties and electrical characteristics of thin thulium oxide (Tm₂O₃) and thulium titanium oxide (Tm₂Ti₂O₇) as gate dielectrics deposited on silicon substrates through reactive sputtering. The structural and morphological features of these films were explored by X-ray diffraction, X-ray photoelectron spectroscopy, secondary ion mass spectrometry, and atomic force microscopy, measurements. It is found that the Tm₂Ti₂O₇ film annealed at 800 °C exhibited a thinner capacitance equivalent thickness of 19.8 Å, a lower interface trap density of 8.37 × 10¹¹ eV⁻¹ cm⁻², and a smaller hysteresis voltage of ∼4 mV than the other conditions. We attribute this behavior to the Ti incorporated into the Tm₂O₃ film improving the interfacial layer and the surface roughness. This film also shows negligible degrees of charge trapping at high electric field stress.     

Relaxation phenomena in ensembles of CoFe2O4 nanoparticles

Collective magnetic behavior of CoFe₂O₄ nanoparticles with diameters of 76, 16, 15 and 8 nm, respectively, prepared by different chemical methods has been investigated. Particle composition, size and structure have been characterized by inductive coupled plasma (ICP), transmission electron microscopy (TEM) and powder X-ray diffraction (PXRD). Basic magnetic properties have been determined from the temperature dependence of magnetization and magnetization isotherms measurements. The three samples exhibit characteristic of a superparamagnetic system with the presence of strong interparticle interactions. Magnetic relaxation phenomena have been examined via frequency-dependent ac susceptibility measurements and aging and memory effect experiments. For the particles coated with oleic acid, it has been demonstrated that the sample reveals all attributes of a super-spin glass (SSG) system with strong interparticle interactions.     

Electrochemical characterization of LiCoO2 as rechargeable electrode in aqueous LiNO3 electrolyte

The development of lithium ion aqueous batteries is getting renewed interest due to their safety and low cost. We have demonstrated that the layer-structure LiCoO₂ phase, the most commonly used electrode material in organic systems, can be successful delithiated and lithiated again in a water-based electrolyte at currents up to 2.70 A/g. The capacity is about 100 mAh/g at 0.135 A/g and can be tuned by cycling the electrode in different potential ranges. In fact, increasing the high cut-off voltage leads to higher specific capacity (up to 135 mAh/g) but the Coulomb efficiency is reduced (from 99.9% to 98.5%). The very good electrode kinetic is probably due to the high conductivity of the electrolyte solution (0.17 Scm^− 1 at 25 °C) but this behavior is affected by the electrode load.     

Magnetic properties of La-substituted NiFe2O4 via egg-white precursor route

Nano-sized NiFe_2−xLa_xO₄ ferrites (x=0.00, 0.01, 0.02, 0.03, 0.04, 0.5, 0.07 and 0.09) were synthesized for the first time by using metal nitrate and egg-white extract in aqueous medium. The ferrites were characterized by DTA-TG, XRD, TEM, FT-IR and VSM techniques. The thermal decomposition behavior revealed that the precursors were completely decomposed at about 420 °C. TEM image shows agglomerated nanoparticles with crystallite sizes agrees well with that estimated by XRD measurement. XRD patterns show a secondary phase of LaFeO₃ besides the cubic structure of the La-substituted ferrites. The lattice parameters, X-ray density and crystallite size were found to increase with the increasing La content. The VSM measurement exhibited a ferromagnetic property for all the samples at room temperature. With increasing La, M_s was found to decrease while H_c increased. The decrease in the saturation magnetization is attributed to the paramagnetic properties of lanthanum, which prefer to substitute iron present in the octahedral sites. The increase in the coercivity is due to either the stronger magnetocrystalline anisotropy induced by La substitution or the change in the crystallite size.     

纯Cr2O3包覆Li4Ti5O12微球的制备及其储锂性能研究

The pure Cr₂O₃ coated Li₄Ti₅O₁₂ microspheres were prepared by a facile and cheap solutionbased method with basic chromium(III) nitrate solution (pH=11.9). And their Li-storage properties were investigated as anode materials for lithium rechargeable batteries. The pure Cr₂O₃ works as an adhesive interface to strengthen the connections between Li₄Ti₅O₁₂ particles, providing more electric conduction channels, and reduce the inter-particle resistance. Moreover, LixCr₂O₃, formed by the lithiation of Cr₂O₃, can further stabilize Li₇Ti₅O₁₂ with high electric conductivity on the surface of particles. While in the acid chromium solution (pH=3.2) modification, besides Cr₂O₃, Li₂CrO₄ and TiO₂ phases were also found in the final product. Li₂CrO₄ is toxic and the presence of TiO₂ is not welcome to improve the electrochemical performance of Li₄Ti₅O₁₂ microspheres. The reversible capacity of 1% Cr₂O₃-coated sample with the basic chromium solution modification was 180 mAh/g at 0.1 C, and 134 mAh/g at 10 C. Moreover, it was even as high as 127 mAh/g at 5 C after 600 cycles. At-20℃, its reversible specific capacity was still as high as 118 mAh/g.