Pressurized-fluid extraction (PFE) of chlorinated paraffins from the biodegradable fraction of source-separated household waste

A method is presented in which pressurized-fluid extraction (PFE) is used for the extraction of chlorinated paraffins (CP) from the biodegradable fraction of source-separated household waste. The conditions that were optimized for high recovery in the extraction procedure were extraction time, temperature, and the use of different solvents and different sample particle sizes, Recoveries of CP from fortified household waste material were over 90%, with only few interferences when cyclohexane was used as solvent. Extraction yields from contaminated samples containing CP were further compared with recoveries obtained by use of Soxtec extraction. The results showed that PFE is a rapid, low-solvent-consuming technique, giving high yields.     

Pressurized-fluid extraction (PFE) of chlorinated paraffins from the biodegradable fraction of source-separated household waste

A method is presented in which pressurized-fluid extraction (PFE) is used for the extraction of chlorinated paraffins (CP) from the biodegradable fraction of source-separated household waste. The conditions that were optimized for high recovery in the extraction procedure were extraction time, temperature, and the use of different solvents and different sample particle sizes. Recoveries of CP from fortified household waste material were over 90%, with only few interferences when cyclohexane was used as solvent. Extraction yields from contaminated samples containing CP were further compared with recoveries obtained by use of Soxtec extraction. The results showed that PFE is a rapid, low-solvent-consuming technique, giving high yields. Received: 13 November 2000 / Revised: 2 March 2001 / Accepted: 7 March 2001     

Analytical-scale microwave-assisted extraction

Microwave-assisted extraction (MAE) is a process of using microwave energy to heat solvents in contact with a sample in order to partition analytes from the sample matrix into the solvent. The ability to rapidly heat the sample solvent mixture is inherent to MAE and the main advantage of this technique. By using closed vessels the extraction can be performed at elevated temperatures accelerating the mass transfer of target compounds from the sample matrix. A typical extraction procedure takes 15-30 min and uses small solvent volumes in the range of 10-30 ml. These volumes are about 10 times smaller than volumes used by conventional extraction techniques. In addition, sample throughput is increased as several samples can be extracted simultaneously. In most cases recoveries of analytes and reproducibility are improved compared to conventional techniques, as shown in several applications. This review gives a brief theoretical background of microwave heating and the basic principles of using microwave energy for extraction. It also attempts to summarize all studies performed on closed-vessel MAE until now. The influences of parameters such as solvent choice, solvent volume, temperature, time and matrix characteristics (including water content) are discussed.     

Homogeneous liquid-liquid extraction of trace amounts of mononitrotoluenes from waste water samples

Homogeneous liquid-liquid extraction method was studied based on a phase separation phenomenon in a ternary solvent system. According to this procedure, mononitrotoloenes were extracted by single-phase extraction in a water/methanol/chloroform, homogeneous ternary solvent system. Methanol and chloroform were used as consolute and extraction solvents, respectively. The homogeneous solution was broken by the addition of salt and a cloudy solution was formed. After centrifugation, the fine droplets of the extraction solvent were sedimented in the bottom of the conical test tube. Analysis of the extracts was carried out by gas chromatography. The optimization procedure was performed using Box-Behnken design. The variables involved were: sample and extraction solvent volumes, consolute solvent volume and phase separator reagent concentration. Optimum results were obtained under the following conditions: sample volume of 5 mL, extraction solvent volume of 55 μL, consolute solvent volume of 1 mL and phase separator reagent concentration; 5% (w/v). Under these conditions, the enrichment factors of 354, 311 and 300, dynamic linear ranges of 0.5-500, 1-500 and 1-500 μg L⁻¹, and limit of detections (LODs) of 0.09, 0.09 and 0.1 μg L⁻¹ were obtained for o-nitrotoluene, m-nitrotoluene and p-nitrotoluene, respectively. Finally, the method was successfully applied to the extraction and determination of MNTs in the waste water samples in the range of micrograms per liter with R.S.Ds. < 13.2%.     

Application of microwave heating for the fast extraction of fat content from the poultry feeds

A rapid method has been developed to extract and quantitatively measure the total oil content in poultry feeds using a domestic microwave oven. The optimized extraction procedure involves the replicate (6×) extraction of 5 g of ground feed with 12 ml of hexane for 20 s in a 900 W oven. Each replicate involves the collection of the resulting miscella and its replacement with fresh solvent for re-extraction. The collected extracts were centrifuged and transferred to a vial. The solvent was evaporated to a constant weight and the residual lipid weighed. In comparison to conventional Soxhlet extraction method, lipid contents obtained using the optimized microwave procedure was not significantly different. However, FTIR analysis indicated that the microwave procedure was superior in minimizing the formation of free fatty acids (FFA) relative to the Soxhlet procedure if the temperature of the sample was kept within the range of 45–50 °C. This simple, sequential extraction procedure is rapid, highly efficient and provides a simple mean of quantitating the lipid content of poultry feed in less than 40 min without the need for specialized microwave oven.     

Comparison of microwave-assisted extraction of aloe-emodin in aloe with Soxhlet extraction and ultrasound-assisted extraction

This paper reports the extraction of aloe-emodin from aloe by microwave-assisted extraction.The effects of various factors,including the solvent,the ratio (mL/g) of the solvent to the sample,microwave irradiation time and microwave power,were discussed in the experiments.The yield of aloe-emodin was determined by HPLC.The optimized conditions for microwave-assisted extraction of aloe-emodin were concluded as follows: the solvent is 80% ethanol (V/V) solution,microwave irradiation time is 3 min and microwave...     

Optimization of a microwave-assisted derivatization-extraction procedure for the determination of chlorophenols in ash samples

A procedure for the determination of 17 chlorophenolic compounds in ash samples obtained from the incineration of waste materials is described. Analytes were simultaneously derivatized with acetic anhydride in presence of triethylamine (TEA), and extracted from the sample in a mixture of n-hexane acetone using a microwave system equipped with closed extraction vessels. Influence of five experimental parameters (volume of TEA and acetic anhydride, extraction time and temperature, as well as the volume of n-hexane acetone) on the yield of the derivatization-extraction procedure was systematically studied using a uniform experimental design at four levels, followed by a conventional factorial design at two levels. Under optimal extraction conditions, recoveries from 72 to 94% were obtained for a spiked ash sample with a carbon content of 8.7%. Quantification limits of the proposed procedure ranged from 2 to 5 ng/g using GC-MS as detection technique. The proposed method was applied to the determination of chlorophenols in three ash samples obtained from different incineration plants. Total chlorophenol contents of 423 and 135 ng/g were found in two of these samples.     

Determination of the oil content of seeds by focused microwave-assisted soxhlet extraction

Sumamry Soybean, rape and sunflower lipids have been extracted with a focused microwave-assisted Saxhlet extractor. The main factors affecting extraction efficiency, namely microwave irradiation power, number of cycles and microwave irradiation time were optimised by means of a power, number of cycles and microwave irradiation time were optimised by means of a central composite design based on a two-level-three-factor factorial design. A study of the influence of particle size on the extraction procedure was also performed. The results obtained were compared with those obtained by use of an ISO method using a conventional Soxhlet extractor. Quantitative results for lipid content based on gravimetric determinations and qualitative results based on analysis of fatty acid methyl esters and polymeric compounds were similar to those obtained by Soxhlet extraction with hexane. Substantial reduction of sample manipulation. analysis time and solvent wastage is achieved by use of the proposed method.     

High-throughput dynamic microwave-assisted extraction on-line coupled with solid-phase extraction for analysis of nicotine in mushroom

A simple and low-cost high-throughput dynamic microwave-assisted extraction (HTDMAE) device was firstly assembled and validated by the extraction of nicotine in mushroom samples. In this device, a household microwave oven was applied to provide the microwave energy; a vacuum pump was used to deliver the solvent. Compared with traditional dynamic microwave-assisted extraction method, the sample throughput and microwave energy utilization were improved by the HTDMAE, up to 20 samples could be treated simultaneously in 9 min. Taking extraction of nicotine in mushroom sample as an example, a method was established with extraction, separation and enrichment of nicotine in a single step by the device on-line coupled with solid-phase extraction (SPE). Nicotine was first extracted from the mushroom samples with water under the action of microwave energy, and then directly introduced into the SPE column which was packed with cation-exchange resins. Subsequently, the nicotine trapped on the resins was eluted with methanol-ammonia (95:5, v/v) and determined by high-performance liquid chromatography. The limit of detection of nicotine obtained is 5.6 μg kg(-1) in fresh mushroom sample. The recovery of nicotine in mushroom samples is in the range of 87.4-104.0%. The proposed method which significantly reduced the overall analysis time and increased sample throughput should be favored for routine analyse of complex solid sample.     

Microwave assisted extraction of soy isoflavones

A fast and reliable analytical method using microwave assisted extraction has been developed. Several extraction solvents (methanol (MeOH) and ethanol (EtOH), 30-70% in water and water), temperatures (50-150 °C), extraction solvent volume, as well as the sample size (1.0-0.1 g) and extraction time (5-30 min) were studied for the optimization of the extraction protocol. The optimized extraction conditions for quantitative recoveries were: 0.5 g of sample, 50 °C, 20 min and 50% ethanol as extracting solvent. No degradation of the isoflavones was observed using the developed extraction protocol and a high reproducibility was achieved (>95%).     

Determination of chlorophenols in soil samples by microwave-assisted extraction coupled to headspace solid-phase microextraction and gas chromatography-electron-capture detection

Microwave-assisted extraction coupled to headspace solid-phase microextraction was studied and applied for one-step in-situ sample preparation prior to analysis of chlorophenols (CPs) in soil samples. The CPs in soil sample were extracted into the aqueous solution and then directly onto the solid-phase microextraction (SPME) fiber in headspace under the aid of microwave irradiation. After being desorbed from SPME fiber in the GC injection port, CPs were analyzed with a GC-electron-capture detection system. Parameters affecting the extraction efficiency such as the extraction solutions, the pH in the slurry, the humic acid content in the soil, the power and the irradiation time of microwave as well as the desorption parameters were investigated. Experimental results indicated that the extraction of a 1.0 g soil sample with a 6-ml aqueous solution (pH 2) and a polyacrylate fiber under the medium-power irradiation (132 W) for 9 min achieved the best extraction efficiency of about 90% recovery and less than 10% RSD. Desorption was optimal at 300 degrees C for 3 min. Detection limits were obtained at around 0.1-2.0 microg/kg levels. The proposed method provided a simple, fast, and organic solvent-free procedure to analyze CPs from soil sample matrix.     

Determination of volatile compounds in Magnolia bark by microwave-assisted extraction coupled to headspace solid-phase microextraction and gas chromatography-mass spectrometry.

A method is described for the determination of volatile compounds in Magnolia bark using microwave-assisted extraction coupled to headspace solid-phase microextraction (MAE-HS-SPME), followed by gas chromatography with mass spectrometry (GC-MS). Parameters affecting the extraction efficiency, such as sampling time and temperature, microwave irradiation power and desorption time, were investigated to achieve the optimal conditions. The result obtained was compared with that of steam distillation; only small differences existed between these two methods. Therefore, the proposed method seems to be a feasible and relatively simple, fast and solvent-free procedure for identification of essential oils in Magnolia bark.     

Comparison of pressurized liquid extraction and microwave assisted extraction for the determination of organochlorine pesticides in vegetables

A method to determine organochlorine pesticides in horticultural samples (lettuce, tomato, spinach, potato, turnip leaf and green bean) using pressurized liquid extraction (PLE) is described and compared with microwave assisted extraction (MAE). Significant parameters affecting PLE procedure such as temperature, static extraction time and extraction solvent were optimised and discussed. Clean-up of extracts was performed by solid phase extraction (SPE) using a carbon cartridge as adsorbent. Pesticides were determined by gas chromatography and electron capture detection (GC-ECD). Analytical recoveries obtained were ca. 100% and the relative standard deviations were lower than 15% for most of the studied pesticides with the proposed methods in each analysed matrix.     

Optimization of microwave-assisted extraction of hydrocarbons in marine sediments: comparison with the Soxhlet extraction method

Microwave energy was applied to extract polycyclic aromatic hydrocarbons (PAHs) and linear aliphatic hydrocarbons (LAHs) from marine sediments. The influence of experimental conditions, such as different extracting solvents and mixtures, microwave power, irradiation time and number of samples extracted per run has been tested using real marine sediment samples; volume of the solvent, sample quantity and matrix effects were also evaluated. The yield of extracted compounds obtained by microwave irradiation was compared with that obtained using the traditional Soxhlet extraction. The best results were achieved with a mixture of acetone and hexane (1:1), and recoveries ranged from 92 to 106%. The extraction time is dependent on the irradiation power and the number of samples extracted per run, so when the irradiation power was set to 500 W, the extraction times varied from 6 min for 1 sample to 18 min for 8 samples. Analytical determinations were carried out by high-performance liquid chromatography (HPLC) with an ultraviolet-visible photodiode-array detector for PAHs and gas chromatography (GC) using a FID detector for LAHs. To test the accuracy of the microwave-assisted extraction (MAE) technique, optimized methodology was applied to the analysis of standard reference material (SRM 1941), obtaining acceptable results.     

Fractionation of heavy metals in sediment by using microwave assisted sequential extraction procedure and determination by inductively coupled plasma mass spectrometry

In this work, a fast microwave assisted extraction procedure was developed and optimized for the heavy metals (Cu, Ni, Cr, Pb and Cd) partitioning in the three-stage sequential extraction procedure proposed by the European Standards, Measurements and Testing (SM&;T) Program, formerly the Community Bureau of Reference (BCR). The microwave oven procedure was optimized to obtain extraction efficiencies similar to the conventional BCR procedure, in less time, while using smaller volumes of reagents. In the optimization process, three variables (extraction time, ramping time and microwave power) were considered as factors and as a response the concentration of different metal ions in each individual BCR fraction. Interactions between analytical factors and their optimized levels were investigated using a central composite design. Extractable metals obtained by both comparable methodologies were measured by inductively coupled plasma mass spectrometry. With the use of optimal microwave conditions, steps 1–3 of the sequential extraction (including the hydrogen peroxide digestion in step 3) could be completed between 21 and 22 min. Detection limits were between 1 and 18 ng l^{− 1}. The accuracy of the proposed method was checked with a certified reference material (CRM) of Lake Sediment BCR 701. Values obtained were in accordance with those reported for the certified material with only a few exceptions. Different origin sediments (river and marine) were analyzed by both BCR and MW procedures, and the results obtained were comparable according to the t-paired-test for a 95% confidence level.     

Determination of dichlorvos by on-line microwave-assisted extraction coupled to headspace solid-phase microextraction and gas chromatography-electron-capture detection

The pretreatment technique of microwave-assisted extraction on-line headspace solid-phase microextraction (MAE-HS-SPME) was designed and studied for one-step in-situ sample preparation prior to the chromatographic analysis of a pesticide on vegetables. The pesticide on chopped vegetables was extracted into an aqueous solution with the aid of microwave irradiation and then directly onto the SPME fiber in headspace. After being collected on to the SPME fiber and desorbed in the GC injection port, the pesticide (dichlorvos) was analyzed with a GC-electron-capture detection system. The optimum conditions for obtaining extraction efficiency, such as the pH, the polarity modifier, and the salt added in sample solution, the microwave irradiation, as well as the desorption parameters were investigated. Experimental results indicated that the proposed MAE-HS-SPME technique attained the best extraction efficiency of 106% recovery under the optimized conditions, i.e. irradiation of extraction solution (10% aqueous ethylene glycol) at pH 5.0 with medium microwave power for 10 min. Desorption at 220 degrees C for 3 min offered the best detection result. The detection was linear at 5-75 microg/l with correlation coefficient of 0.9985. Detection limit was obtained at approximately 1.0 microg/l level based on S/N=3. The proposed method provided a very simple, fast, and solvent-less procedure to collect pesticides directly from vegetables for GC determination. Its application was illustrated by the analysis of trace dichlorvos in vegetables.     

Optimization of microwave-assisted extraction of hydrocarbons in marine sediments: comparison with the Soxhlet extraction method

Microwave energy was applied to extract polycyclic aromatic hydrocarbons (PAHs) and linear aliphatic hydrocarbons (LAHs) from marine sediments. The influence of experimental conditions, such as different extracting solvents and mixtures, microwave power, irradiation time and number of samples extracted per run has been tested using real marine sediment samples; volume of the solvent, sample quantity and matrix effects were also evaluated. The yield of extracted compounds obtained by microwave irradiation was compared with that obtained using the traditional Soxhlet extraction. The best results were achieved with a mixture of acetone and hexane ¶(1?:?1), and recoveries ranged from 92 to 106%. The extraction time is dependent on the irradiation power and the number of samples extracted per run, so when the irradiation power was set to 500 W, the extraction times varied from 6 min for 1 sample to 18 min for 8 samples. Analytical determinations were carried out by high-performance liquid chromatography (HPLC) with an ultraviolet-visible photodiode-array detector for PAHs and gas chromatography (GC) using a FID detector for LAHs. To test the accuracy of the microwave-assisted extraction (MAE) technique, optimized methodology was applied to the analysis of standard reference material (SRM 1941), obtaining acceptable results.     

Metal fractionation in olive oil and urban sewage sludges using the three-stage BCR sequential extraction method and microwave single extractions

The conventional three-stage BCR sequential extraction method was employed for the fractionation of heavy metals in sewage sludge samples from an urban wastewater treatment plant and from an olive oil factory. The results obtained for Cu, Cr, Ni, Pb and Zn in these samples were compared with those attained by a simplified extraction procedure based on microwave single extractions and using the same reagents as employed in each individual BCR fraction. The microwave operating conditions in the single extractions (heating time and power) were optimized for all the metals studied in order to achieve an extraction efficiency similar to that of the conventional BCR procedure. The measurement of metals in the extracts was carried out by flame atomic absorption spectrometry. The results obtained in the first and third fractions by the proposed procedure were, for all metals, in good agreement with those obtained using the BCR sequential method. Although in the reducible fraction the extraction efficiency of the accelerated procedure was inferior to that of the conventional method, the overall metals leached by both microwave single and sequential extractions were basically the same (recoveries between 90.09 and 103.7%), except for Zn in urban sewage sludges where an extraction efficiency of 87% was achieved. Chemometric analysis showed a good correlation between the results given by the two extraction methodologies compared. The application of the proposed approach to a certified reference material (CRM-601) also provided satisfactory results in the first and third fractions, as it was observed for the sludge samples analysed.     

An absorbing microwave micro-solid-phase extraction device used in non-polar solvent microwave-assisted extraction for the determination of organophosphorus pesticides

A single-step extraction-cleanup method, including microwave-assisted extraction (MAE) and micro-solid-phase extraction (μ-SPE), was developed for the extraction of ten organophosphorus pesticides in vegetable and fruit samples. Without adding any polar solvent, only one kind of non-polar solvent (hexane) was used as extraction solvent in the whole extraction step. Absorbing microwave μ-SPE device, was prepared by packing activated carbon with microporous polypropylene membrane envelope, and used as not only the sorbent in μ-SPE, but also the microwave absorption medium. Some experimental parameters effecting on extraction efficiency was investigated and optimized. 1.0 g of sample, 8 mL of hexane and three absorbing microwave μ-SPE devices were added in the microwave extraction vessel, the extraction was carried out under 400 W irradiation power at 60 °C for 10 min. The extracts obtained by MAE-μ-SPE were directly analyzed by GC–MS without any clean-up process. The recoveries were in the range of 93.5–104.6%, and the relative standard deviations were lower than 8.7%.     

Improved solvent-free microwave extraction of essential oil from dried Cuminum cyminum L. and Zanthoxylum bungeanum Maxim

Solvent-free microwave extraction (SFME) is a recently developed green technique which is performed in atmospheric conditions without adding any solvent or water. SFME has already been applied to extraction of essential oil from fresh plant materials or dried materials prior moistened. The essential oil is evaporated by the in situ water in the plant materials. In this paper, it was observed that an improved SFME, in which a kind of microwave absorption solid medium, such as carbonyl iron powders (CIP), was added and mixed with the sample, can be applied to extraction of essential oil from the dried plant materials without any pretreatment. Because the microwave absorption capacity of CIP is much better than that of water, the extraction time while using the improved SFME is no more than 30 min using a microwave power of 85 W. Compared to the conventional SFME, the advantages of improved SFME were to speed up the extraction rate and need no pretreatment. Improved SFME has been compared with conventional SFME, microwave-assisted hydrodistillation (MAHD) and conventional hydrodistillation (HD) for the extraction of essential oil from dried Cuminum cyminum L. and Zanthoxylum bungeanum Maxim. By using GC-MS system the compositions of essential oil extracted by applying four kinds of extraction methods were identified. There was no obvious difference in the quality of essential oils obtained by the four kinds of extraction methods.