新型Mn-Fe/Al_2O_3高温脱除H_2S的实验研究(Ⅱ)

本文首先研究了粒度dp=07mm脱硫剂的脱硫反应和再生反应性能。研究表明当Mn∶Fe=2∶1(w)、载体在1000℃焙烧后,脱硫剂有较好的脱硫反应性能,其最佳的脱硫反应温度为550℃,且在710℃、O2浓度低于1083%(v)、空速2000～3000h-1再生条件下,可完全对脱硫剂进行再生;H2S浓度影响脱硫剂的初始脱硫反应速率和穿透反应时间,但对脱硫剂的脱除率和穿透硫容影响不大。并研究了粒度dp=3mm脱硫剂的脱硫情况。实验结果表明,小颗粒脱硫剂的脱硫反应主要为化学反应控制,大颗粒脱硫剂主要为扩散控制。为此对大颗粒脱硫剂进行了工程设计,即采用活性组分非均布脱硫剂。研究表明,非均布脱硫剂明显提高了脱硫剂的平均脱硫反应速率和硫容,同均布脱硫剂相比,非均布脱硫剂再生后具有较好的脱硫稳定性能。     

聚合离子液体磷钨酸盐合成及催化模拟油氧化脱硫

合成了新型的聚合离子液体磷钨酸盐(聚1-丁基-3-乙烯基咪唑磷钨酸盐)(PBVIm PW),采用FT-IR、XRD和TG进行表征,通过CHN元素和ICP分析确定其结构。催化剂用于过氧化氢为氧化剂的模拟油品氧化脱硫反应。考察反应温度、氧硫比、催化剂用量等对脱硫率的影响。结果表明,当反应温度为50℃,n(H_2O_2)/n(S)为8,n(PBVIm PW(P))/n(BT)为0.4∶1.0,反应时间150 min时,苯并噻吩(BT)的转化率可以达到99.4%。催化剂可回收重复使用四次,催化活性无明显下降。     

离子液体中过氧钨配合物催化氧化燃油脱硫

合成了一种含D,L-丙氨酸配体的钨的过氧配合物WO(O2)2·2C3H7NO2·H2O催化剂.以WO(O2)2·2C3H7NO2·H2O/[Bmim]PF6/H2O2体系为研究模型,考察了反应时间、温度和催化剂用量等因素对燃油脱硫率的影响.结果表明,在70℃反应2h,n(H2O2)∶n(二苯并噻吩)∶n(催化剂)=30...     

酸性离子液体中八聚钼酸盐相转移催化氧化脱硫的研究

制备了四种八聚钼酸盐催化剂:[(C4H9)4N]4Mo8O26,[(C12H25)N(CH3)3]4Mo8O26,[(C14H29)N(CH3)3]4Mo8O26和[(C16H33)N(CH3)3]4Mo8O26。通过元素分析,TG/DSC,FT-IR和紫外-可见光谱等方法对这四种催化剂的组成和结构进行了相应表征。研究了八聚钼酸季铵盐催化剂在酸性离子液体中相转移催化氧化脱硫活性。同时考察了在不同脱硫体系和催化剂、温度(T)、时间(t)、氧化剂(H2O2)用量、催化剂用量、以及酸性离子液体的种类等因素对脱硫效果的影响。经过对反应条件优化,当在70℃下反应3 h,n(H2O2)∶n(DBT)=4∶1,n(DBT)∶n(Catalyst)=10∶1,离子液体[(CH2)3SO3HMIm]BF4用量为1 mL,模拟油品中二苯并噻吩(DBT)脱除率可以达到98.3%,且循环反应6次后催化反应活性没有明显的下降,可以用来进行深度脱硫。最后,对该脱硫体系的脱硫机理进行了讨论。     

焦煤中添加废塑料和脱硫剂的焦化过程研究

在模拟焦化室和焦化条件下，进行了焦煤中直接添加废塑料和脱硫剂后的焦化过程的研究，分析了焦化过程中焦炉煤气H2S脱除效果及脱硫剂和废塑料的添加对焦炭硫和锌及其在焦炭中残留率的影响。结果表明，焦煤的焦化过程中，直接添加ZnO、Fe2O3或冶金粉尘(MD)作为脱硫剂，当关键脱硫组分ZnO和（或）Fe2O3与可挥发性硫的摩尔比(nZn+Fe/nS)为1.2时，焦炉煤气H2S脱除效果均较好，塑料本身的热分解使得焦煤中添加质量分数为5%的废塑料后焦炭产率从81.52％降到77.61％；当焦煤中添加质量分数为5％的废塑料，并以ZnO为脱硫剂时，由于塑料中硫的质量分数相对焦煤要高，所以需要增nZn+Fe/nS到1.7，才能取得较好的煤气脱硫效果，与此同时焦炭中锌和硫的质量分数均有不同程度的增加。     

N,N′-二(十二烷基)乙二胺二乙酸萃取汞的研究

研究了N ,N′ 二 (十二烷基 )乙二胺二乙酸 (简写为H2 R2 Y)的氯仿溶液对汞 (Ⅱ )的萃取行为。考察了酸度、萃取剂浓度、相比及温度等因素对萃取率的影响 ;用电导法及摩尔比法测得萃合物的摩尔比为 1∶1 ;测定了新试剂H2 R2 Y对Hg2 与Fe3 、Co2 、Ni2 、Zn2 、Cr3 、Mn2 等金属离子的分离效果 ;并根据分配比与温度的关系求出了萃取反应的ΔH0 、ΔS0 、ΔG0 和lgKex值 ,该萃取反应为放热反应。     

粉尘对高温煤气脱硫反应的影响

研究了在400℃-550℃范围内粉尘对氧化铁高温脱硫剂的硫容和脱硫反应速度的影响。结果表明随着温度的升高,粉尘对脱硫剂的硫容和脱硫反应速度的影响增大。并利用收缩核模型计算比较了由于粉尘加入引起的H2S有效扩散系数的变化,发现有效扩散系数由于粉尘的作用,随温度升高显著降低。为脱硫除尘一体化工艺的开发提供了一定的理论依据。     

萃取Fe3+和氨水-乙醇反萃沉淀法制备α-Fe2O3

以磷酸二异辛基酯(P204)为萃取剂,CCl4为溶剂,从Fe(NO3)2水溶液中萃取铁离子,以氨的乙醇溶液反萃含铁的有机相,通过优化控制相间传质过程,获得了Fe(OH)3前驱体,经煅烧后得α-Fe2O3粉体,采用TEM、FTIR、XRD等测试技术对α-Fe2O3进行表征。 研究表明,在油水相比为1∶1,水相c(Fe3+)=0.10 mol/L(pH=3.0)、油相P204为V(P204)∶V(CCl4)=1∶3、平衡时间为20 min,Fe3+萃取率达98.44%;反萃取溶液V(氨水)∶V(乙醇)=1∶7、陈化温度约10.0 ℃,制备纳米α-Fe2O3的煅烧温度为600 ℃较宜。     

大学化学实验电势-pH曲线测定探讨

大学化学实验电势-pH曲线测定中采用的电极反应S 2H 2e-=H2S(g)的电极电势表达式有误,导致所绘制的电势-pH曲线与教科书要求不符;没有给出电极反应FeY- e-= FeY2-的标准电极电势φθ,易使学生误将电极反应Fe3 e-=Fe2 的φθ=0.771V作为电极反应FeY- e-= FeY2-的φθ;仅从两个电极反应电极电势的差值来确定脱硫氧化-还原反应的最佳pH范围不够全面,应结合溶液中络合物的稳定性、液相催化湿法脱硫原理、脱硫溶液pH对H2S吸收反应的影响、对再生反应的影响和脱硫过程的经济性等多方面考虑,使学生有全面综合的认识.     

wo3催化h2o2氧化环己酮合成己二酸

以WO3为催化剂,在无有机溶剂和相转移催化剂的情况下,用H2O2氧化环己酮合成己二酸。探讨了催化剂用量、H2O2用量、反应温度和时间等条件对反应的影响。在优化条件下:n(环己酮)∶n(H2O2)∶n(WO3)=100∶500∶2,反应温度为120℃,反应6 h,己二酸分离收率可达80.3%,纯度为99.8%;催化剂重复使用5次后己二酸收率仍可达70.2%。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.