聚乙烯咔唑/杂多阴离子杂化LB膜的制备、结构与光电性质

首次选用聚乙烯咔唑（PVK）、二十二烷酸（BA）与杂多阴离子用LB技术制备 了五种有机/无机杂化LB膜，PVK/BA/HPC（HPC = Na_5(PZ(H_2O)Mo_(11)O_(39)]· 5H_2O, Z = Mn, Co, Cu, Zn, Ni）。用原子力显微镜（AFM），UV-vis，小角X射 线衍射（LAXRD），表面光电压谱（SPS），荧光光谱等对LB膜的结构与性质进行了 表征。结果表明：它们在空气/水界面有好的成膜性能，崩溃压为22 ～27 mN/m， 杂多阴离子作为一个单层夹在PVK和BA双层之间。PVK/BA/HPC LB膜的光致发光具有 PVK激基缔合物的特征荧光，其光电压谱有较强的光电响应。     

Molecular Orientation and Structure in LB Films of a Liquid Crystal MPUOPM Investigated by UV-Vis and IR Spectroscopy

"?Langmuir monolayers and LB films of 4-((s)-2-methylbutoxy)phenyl-(4'-(10-undecen-1-oyloxy)phenyl) methylenimine (MPUOPM) were investigated by ultraviolet-visible, polarized infrared spectroscopy. ?-A isotherms showed well-defined Langmuir monolayers were formed at an air/water interface for the MPUOPM and their mixture with SA. An inflection point at 13 mN/m appeared on the isotherm, which was due to the transition from the monolayer to multilayer. The polarized IR spectra of LB films of MPUOPM had provided new insight into the molecular orientation and structure. In LB films, the tilted angle between the alkyl chain and the normal line of the substrate was 48ffi, the tilted angle between the dipole moment of C=N and the normal line of the substrate was 51ffi. The alkyl chains assumed a trans-zigzag conformation but it included a few gauche conformers. The C=N groups were almost in one plane in the LB films. "     

Study of Langmuir and Langmuir-Blodgett films of odorant-binding protein/amphiphile for odorant biosensors

To make ultrathin films for the fabrication of artificial olfactory systems, odorant biosensors, we have investigated mixed Langmuir and Langmuir-Blodgett films of odorant-binding protein/amphiphile. Under optimized experimental conditions (phosphate buffer solution, pH 7.5, OBP-1F concentration of 4 mg L(-1), target pressure 35 mN m(-1)), the mixed monolayer at the air/water interface is very stable and has been efficiently transferred onto gold supports, which were previously functionalized by self-assembled monolayers (SAMs) with 1-octadecanethiol (ODT). Atomic force microscopy and electrochemical impedance spectroscopy were used to characterize mixed Langmuir-Blodgett (LB) films before and after contact with a specific odorant molecule, isoamyl acetate. AFM phase images show a higher contrast after contact with the odorant molecule due to the new structure of the OBP-1F/ODA LB film. Non-Faradaic electrochemical spectroscopy (EIS) is used to quantify the effect of the odorant based on the electrical properties of the OBP-1F/ODA LB film, as its resistance strongly decreases from 1.18 MOmega (before contact) to 25 kOmega (after contact).     

Alkylamine sensing using langmuir-blodgett films of n-alkyl-N-phenylamide-substituted zinc porphyrins

Two porphyrin compounds, zinc(II) 5,10,15,20-tetrakis(3,5,5-trimethyl- N-phenylhexanamide)porphyrin and zinc(II) 5,10,15,20-tetrakis(2,2-dimethyl- N-phenylpropanamide)porphyrin, have been investigated as possible candidates for the detection of alkylamines. UV-visible spectroscopy has shown that their solution absorption spectra are significantly modified upon interaction with a range of organic analytes, including acetic acid, butanone, ethylacetate, hexanethiol, octanal, octanol, alkylamines, and trimethylphosphite. Large spectral changes are observed for the family of alkylamines as a result of the specific affinity between zinc and the amine moiety. Langmuir-Blodgett (LB) films of the porphyrins have been fabricated in order to assess their solid-state sensing capability toward amines. The surface pressure-area (Pi- A) isotherms reveal a clear three-phase Langmuir film behavior and show that these monolayer films may be compressed to a relatively high surface pressure ( approximately 40-50 mN m (-1)). The isotherm data alongside molecular modeling suggest a relatively flat orientation of the porphyrin rings of both compounds: that is, a mutually parallel alignment of the plane of the porphyrin ring and that of the water surface. LB films deposited at 15 mN m (-1) have been exposed to alkylamine vapor (carried by N 2). A red shift and increase in intensity of the Soret band absorbance is observed which can be reversed by flowing pure N 2 over the gently heated sample (60 degrees C) after exposure. Primary amines were expected to invoke the greatest sensing response due to (i) their larger association constants with these porphyrins compared to secondary and tertiary amines and (ii) the ease of diffusion of amines which is expected to follow the order primary > secondary > tertiary due to the steric hindrance arising from the bulky secondary and tertiary amines. However, the magnitude of the absorbance change is largest for exposure to the secondary amines, dipropylamine and dibutylamine, for both porphyrins, compared to primary and tertiary amines. This trend follows that observed when the amines were added to solutions of the porphyrins. The rate of response of the porphyrin LB films falls as the molecular weight of the diffusing alkylamine increases. Furthermore, a greater rate of response is observed for the phenylhexanamide porphyrin compared to the phenylpropanamide porphyrin due to its lower molecular density within the LB film and therefore more porous structure.     

Preparation of ordered films containing a phenylene ethynylene oligomer by the Langmuir-Blodgett technique

This paper reports the fabrication and characterization of Langmuir and Langmuir-Blodgett (LB) films incorporating an oligo(phenylene-ethynylene) (OPE) derivative, namely, 4-[4-(4-hexyloxyphenylethynyl)-phenylethynyl]-benzoic acid (HBPEB). Conditions appropriate for deposition of monolayers of HBPEB at the air-water interface have been established and the resulting Langmuir films characterized by a combination of surface pressure and surface potential versus area per molecule isotherms, Brewster angle microscopy, and ultraviolet reflection spectroscopy. The Langmuir films are readily transferred onto solid substrates, and one-layer LB films transferred at several surface pressures onto mica substrates have been analyzed by means of atomic force microscopy, from which it can be concluded that 14 mN/m is an optimum surface pressure of transference, giving well-ordered homogeneous films without three-dimensional defects and a low surface roughness. The optical and emissive properties of the LB films have been determined with significant blue-shifted absorption spectra indicating formation of two-dimensional H aggregates and a Stokes shift illustrating the effects of the solid-like environment on the molecular chromophore.     

嵌入花生酸镉单层中的卟啉-紫精分子聚集行为的研究

本文制备了卟啉-紫精与花生酸镉混合LB膜, 用紫外可见光谱研究了膜中卟啉基团的聚集及取向, X射线衍射说明混合LB膜具有层状有序的周期结构。扫描电镜结果表明: 通过调节膜的表面压可使聚集成"微畴"的卟啉-紫精均匀分布在花生酸镉单分子层中, 随膜表面压的增大, 小的"微畴"相互连接形成更大的"微畴"。电子衍射说明混合膜中两组份分相存在, 且都为六角对称的有序结构。     

Molecular packing tunes the activity of Kluyveromyces lactis beta-galactosidase incorporated in Langmuir-Blodgett films

Functional consequences of constraining beta-Gal in bidimensional space were studied at defined molecular packing densities and constant topology. Langmuir-Blodgett films, LB15 and LB35 composed of dipalmitoyl phosphatidylcholine and K. lactis beta-Gal, were obtained by transferring Langmuir films (L) initially packed at 15 and 35 mN/m, respectively, to alkylated glasses. The beta-Gal-monolayer binding equilibrium, mainly the adsorption rate and affinity, depended on the initial monolayer's surface pressure (lower for higher pi i). At pi i = 15 and 35 mN/m, the surface excess (Gamma) followed downward parabolic and power-law tendencies, respectively, as a function of subphase protein concentration. Gamma values in L roughly reflected the protein surface density chemically determined in LBs (0-7.5 ng/mm2 at pi i = 0-35 mN/m and [beta-Gal] subphase = 0-100 microg/mL). The beta-Gal-catalyzed hydrolysis of o-nitrophenyl-galactopyranoside showed a Michaelian kinetics in solution as well as in LB15. KM, KM,LB15, Vmax, and Vmax,LB15 were 5.15 +/- 2.2 and 9.25 +/- 6 mM and 39.63 and 0.0096 +/- 0.0027 micromol/min/mg protein, respectively. The sigmoidal kinetics observed with LB35 was evaluated by Hill's model (K0.5 = 9.55 +/- 0.4 mM, Vmax,35 = 0.0021 micromol/min/mg protein, Hill coefficient n = 9) and Savageau's fractal model (fractal constant K f = 9.84 mM; reaction order for the substrate gs = 9.06 and for the enzyme ge = 0.62). Fractal reaction orders would reflect the fractal organization of the environment, demonstrated by AFM images, more than the molecularity of the reaction. Particular dynamics of the protein-lipid structural coupling in each molecular packing condition would have led to the different kinetic responses.     

Microstructure and Ion Exchange in Stearic Acid Langmuir-Blodgett Films Studied by Fourier Transform Infrared-Attenuated Total Reflection Spectroscopy

Fourier transform infrared-attenuated total reflection (FTIR-ATR) spectra have been recorded of 11-layer Langmuir-Blodgett (LB) films of stearic acid deposited at various surface pressures (0.1, 15, and 35 mN/m), and the molecular orientation angles were evaluated quantitatively, which supplied insight into the molecular order with the alkyl chains tightly packed like crystal in the LB films deposited at the zero and higher surface pressures. These experimental results indicate that, in the Langmuir film as the precursor of LB films, stearic acid molecules self-aggregate to form two-dimensional crystalline domains already even at the zero surface pressure, which results in the inhomogeneity of monolayer. The analysis of dependence of nu(C=O) intensity on the surface pressure, surface density, and subphase temperature leads to the conclusion that the defects in LB films originate from the Langmuir film and be conserved upon deposition. Annealing below 50 degrees C and cooling could improve the monolayer homogeneity, and thus a defect-free or low-defect LB films can be deposited. Furthermore, ion exchange conducted in the LB films, on the other hand, confirms the existence of structure defects in LB films of stearic acid. The polar plane microstructure, lateral transport along the polar planes and the coordination types of stearic acid/cation system may be the rate-limiting process. The results have implication on the possible uses of stearic acid LB films as ion-exchange materials or sensors. Copyright 2001 Academic Press.     

有机金属聚合物/多酸纳米杂化LB膜的制备与光电性质研究

以含有共轭大π键的有机金属聚合物(OMP)作有机组分, 以Keggin结构和Dawson结构钨(钼)磷杂多酸作无机组分, 以十八胺为辅助成膜剂, 用LB技术制备了3种新型有机金属聚合物/十八铵/杂多阴离子OMP/ODA/HPA (HPA＝PMo₁₂, PW₁₂, P₂Mo₁₈)杂化LB膜. 用π-A曲线﹑UV-vis吸收光谱﹑荧光光谱﹑原子力显微镜(AFM)﹑扫描隧道显微镜(STM)和表面光电压谱(SPS)对标题LB膜的成膜性能及光电性质进行了研究, 结果表明标题杂化LB膜的崩溃压为26.8 mN/m, 在可见光区有较强的光电压响应, 并有好的发光性质. 当电压为±8.0 V时, 隧道电流是－0.1～－2.3 nA.     

8-羟基喹啉镧两亲性配合物LB膜的双层电致发光器件

以具有不同层数的两亲配合物二[2-(N-十六烷基氨基甲酰基)-8-羟基喹啉]合镧[La(HQ)₂Cl]的LB膜为发光层,PBD为电子传输层,制备了双层结构的电致发光(EL)器件:ITO/LB膜/PBD/Al.器件产生黄绿色注入式发光.LB膜的层数和沉积压对器件的性能具有重要影响.在16V激发电压下,5,11和21层LB膜双层EL器件的电流密度分别为48,29和16.4mA/cm²,启亮电压阀值为7.5,8.5和9.5V.器件的亮度随电流密度和驱动电压的增加而增加.在相同偏压下,21层LB膜EL器件的亮度大于5和11层LB膜的器件.在25mN/m沉积的LB膜制备的EL器件具有较高的亮度(1219cd/m₂)和击穿电压.     

不同羧酯比的聚马来酸十八醇酯齐聚物的镉盐LB膜成膜特性研究

由聚马来酸杆和十八醇合成了一系列不同羧酯比的聚马来酸十八醇酯（PMA），并以其为成膜材料、CdCl2水溶液为亚相制备了一系列聚马来酸十八醇酯镉盐（CdPMA）LB膜．借助小角X射线衍射和红外吸收光谱表征了成膜条件及羧酯比对CdPMA膜有序结构的影响．在较高膜压（30mN／m）和快速提拉（10cm／min）条件下，低羧酯比的CdPMA可得到有序性很高的Y-型LB多层膜；高羧酯比的CdPMA得不到高有序性的LB多层膜．     

Langmuir-Blodgett-Kuhn and self-assembled films of asymmetrically substituted poly(paraphenylene)

Asymmetrically substituted poly(paraphenylene) (PhPPP) with hydrophilic and hydrophobic side chains was investigated. The polymer behavior at the air-water interface was studied on the basis of surface pressure-area (pi-A) isotherms and compression/expansion hysteresis measurements. PhPPP can form stable monolayers with an area per repeat unit of A=0.20+/-0.02 nm2 and a collapse pressure in the range of pi=25 mN/m. Then, Langmuir-Blodgett-Kuhn (LBK) films of PhPPP were prepared by horizontally and vertically transferring the Langmuir monolayers onto hydrophilic solid substrates at pi=12 mN/m. Cross-section analysis of the AFM tapping-mode topography images of a single transferred monolayer reveals a thickness of d0=0.9+/-0.1 nm. Taking into account the obtained monolayer thickness, curve-fitting calculations of angular scan data of LB monolayers measured using surface plasmon resonance (SPR) spectroscopy lead to a value for the refractive index of n=1.78+/-0.02 at lambda=632.8 nm. Next, the spontaneous formation of a PhPPP monolayer by adsorption from solution was studied ex situ by atomic force microscopy and UV-vis spectroscopy and in situ by using SPR spectroscopy. Stable self-assembled monolayers of PhPPP can be formed on hydrophilic surfaces with a thickness similar to that of the monolayer obtained using the LB method. The characterization results confirmed the amphiphilic character and the self-assembly properties of PhPPP, as well as the possibility of preparing homogeneous monolayer and multilayer films.     

柔性间隔基对于香豆素取代二乙炔LB膜聚合及手性形成的影响

设计合成了2种香豆素取代二乙炔单体,7-(10,12-二十三双炔酰氧基)-香豆素(CODA)和7-(10,12-二十三双炔酰氧乙氧基)-香豆素(CO2DA),研究了柔性间隔基对香豆素取代二乙炔单体在气-液界面的组装、单体LB膜的聚合以及聚二乙炔主链螺旋结构形成的影响.利用Langmui-Blodgett(LB)技术,以纯水为亚相,膜压在35 mN/m时沉积制备了香豆素取代二乙炔单体LB膜.尽管CODA是非手性的,但其LB膜均表现出明显的宏观手性信号.这是由于在压缩过程中香豆素基团间强烈的π-π堆积,形成了螺旋排列,显示出超分子手性.而CO2DA LB膜无明显CD信号.经254 nm紫外光辐照,CODA LB膜聚合成蓝相,聚二乙炔主链表现出明显的宏观手性.而CO2DA LB膜聚合后无明显的CD信号.薄膜中香豆素功能基团的不规则排列不利于二乙炔单体的固态聚合以及聚二乙炔主链螺旋结构的形成.     

Preparation and Characterization of 6-<Emphasis Type="Italic">O</Emphasis>-(4-stearyloxytrityl)Cellulose acetate Langmuir–Blodgett Films

Multilayer films of 2,3-di-O-acetyl-6-O-(4-stearyloxytrityl)cellulose (ASTC) were prepared and investigated. The fairly high surface pressure (π)–area (A) isotherms (36– 47 mN/m) suggest that the balky and hydrophobic trityl group contribute to form a condensed monolayer. The cellulose derivative formed a homogeneous monolayer at 10 mN/m. The monolayer on the water surface was transferred successfully at 10 mN/m onto various substrates by modifying the preparation methods, to form Z-type multilayer films. The ultraviolet–visible (UV–Vis) absorbance was independent of the number of layers, indicating that each layer is made of definite number of anhydroglucose unit (AGU). The monolayer thickness determined from atomic force microscope (AFM) and ellipsometry was calculated to be about 1.9 nm, suggesting that the long alkyl chain in the film has a so-called hairy-rod type structure. This is the first paper about the Z-type LB film prepared from cellulose derivatives having long mono-alkyl chain only at 6-O-position.     

Fabrication, structural characterization, and applications of langmuir and langmuir-blodgett films of a poly(azo)urethane

The synthesis of a poly(azo)urethane by fixing CO(2) in bis-epoxide followed by a polymerization reaction with an azodiamine is presented. Since isocyanate is not used in the process, it is termed "clean method" and the polymers obtained are named "NIPUs" (non-isocyanate polyurethanes). Langmuir films were formed at the air-water interface and were characterized by surface pressure vs mean molecular area per mer unit (Pi-A) isotherms. The Langmuir monolayers were further studied by running stability tests and cycles of compression/expansion (possible hysteresis) and by varying the compression speed of the monolayer formation, the subphase temperature, and the solvents used to prepare the spreading polymer solutions. The Langmuir-Blodgett (LB) technique was used to fabricate ultrathin films of a particular polymer (PAzoU). It is possible to grow homogeneous LB films of up to 15 layers as monitored using UV-vis absorption spectroscopy. Higher number of layers can be deposited when PAzoU is mixed with stearic acid, producing mixed LB films. Fourier transform infrared (FTIR) absorption spectroscopy and Raman scattering showed that the materials do not interact chemically in the mixed LB films. The atomic force microscopy (AFM) and micro-Raman technique (optical microscopy coupled to Raman spectrograph) revealed that mixed LB films present a phase separation distinguishable at micrometer or nanometer scale. Finally, mixed and neat LB films were successfully characterized using impedance spectroscopy at different temperatures, a property that may lead to future application as temperature sensors. Principal component analysis (PCA) was used to correlate the data.     

Infrared spectroscopy analysis of the structure of multilayer Langmuir-Blodgett films: effect of deposition velocity and pH

Multiple Langmuir-Blodgett (LB) films of arachidic acid were deposited on germanium (Ge) substrates from subphase solutions of 10(-4) M CdCl2 at different pH values and at different deposition speeds. Attenuated total reflectance infrared (ATR-IR) spectroscopy was used to obtain information on the molecular order and structure of these multilayer LB films. At pHs higher than the pKa of the fatty acid/cation system, transfers took place only during the downstroke, indicating X-type deposition. At pH = pKa and large deposition speeds, deposition partially failed during the downstroke, resulting in Z-type depositions. Analysis of the infrared spectra indicates that multiple LB films deposited only during the upstroke (Z-type) or during downstrokes (X-type) have a centrosymmetric structure typical of films deposited during the upstroke and downstroke, except for a slight decrease in molecular order and tilt angle as the pH increases (X-type). The centrosymmetric structure indicates that rearrangement of layers takes place between cycles. Experimental evidence of such rearrangement occurring in a fatty acid/divalent cation salt subphase is shown here, and rearrangement alternatives are discussed.     

Changes in the near-edge X-ray absorption fine structure spectra of long-chain diacetylene derivatives through photopolymerization in Langmuir–Blodgett films

Photopolymerization of cadmium 10,12-pentacosadiynoate (CdDA) in Langmuir–Blodgett (LB) films, with the molecular packing well arranged by moderate preannealing, was investigated with near-edge X-ray absorption fine structure (NEXAFS) spectroscopy. Greenish films of polydiacetylene with an absorption wavelength of 705 nm were obtained through the photopolymerization of preannealed monomer LB films, and this resulted in an extended π-conjugate system based on the well-ordered monomer in a two-dimensional arrangement. The electronic structures of the polydiacetylenes were found to be correlated to the variation of the molecular arrangements in the films from the changes in the NEXAFS spectra through photopolymerization in the LB films. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2329–2336, 2004     

Two-dimensional self-assembly of linear poly(ethylene oxide)-b-poly(epsilon-caprolactone) copolymers at the air-water interface

The interfacial properties of amphiphilic linear diblock copolymers based on poly(ethylene oxide) and poly(epsilon-caprolactone) (PEO-b-PCL) were studied at the air-water (A/W) interface by surface pressure measurements (isotherms and hysteresis experiments). The resulting Langmuir monolayers were transferred onto mica substrates and the Langmuir-Blodgett (LB) film morphologies were investigated by atomic force microscopy (AFM). All block copolymers had the same PEO segment (Mn = 2670 g/mol) and different PCL chain lengths (Mn = 1270; 2110; 3110 and 4010 g/mol). Isothermal characterization of the block copolymer samples indicated the presence of three distinct phase transitions around 6.5, 10.5, and 13.5 mN/m. The phase transitions at 6.5 and 13.5 mN/m correspond to the dissolution of the PEO segments in the water subphase and crystallization of the PCL blocks above the interface similarly as for the corresponding homopolymers, respectively. The phase transition at 10.5 mN/m was not observed for the homopolymers alone or for their blends and arises from a brush formation of the PEO segments anchored underneath the adsorbed hydrophobic PCL segments. AFM analysis confirmed the presence of PCL crystals in the LB films with unusual hairlike/needlelike architectures significantly different from those obtained for PCL homopolymers.     

Thermodynamic characteristics and Langmuir-Blodgett deposition behavior of mixed DPPA/DPPC monolayers at air/liquid interfaces

The role of dipalmitoylphosphatic acid (DPPA) as a transfer promoter to enhance the Langmuir-Blodgett (LB) deposition of a dipalmitoylphosphatidylcholine (DPPC) monolayer at air/liquid interfaces was investigated, and the effects of Ca2+ ions in the subphase were discussed. The miscibility of the two components at air/liquid interfaces was evaluated by surface pressure-area per molecule isotherms, thermodynamic analysis, and by the direct observation of Brewster angle microscopy (BAM). Multilayer LB deposition behavior of the mixed DPPA/DPPC monolayers was then studied by transferring the monolayers onto hydrophilic glass plates at a surface pressure of 30 mN/m. The results showed that the two components, DPPA and DPPC, were miscible in a monolayer on both subphases of pure water and 0.2 mM CaCl2 solution. However, an exception occurs between X(DPPA)=0.2 and 0.5 at air/CaCl2-solution interface, where a partially miscible monolayer with phase separation may occur. Negative deviations in the excess area analysis were found for the mixed monolayer system, indicating the existence of attractive interactions between DPPA and DPPC molecules in the monolayers. The monolayers were stable at the surface pressure of 30 mN/m for the following LB deposition as evaluated from the area relaxation behavior. It was found that the presence of Ca2+ ions had a stabilization effect for DPPA-rich monolayers, probably due to the association of negatively charged DPPA molecules with Ca2+ ions. Moreover, the Ca2+ ions may enhance the adhesion of DPPA polar groups to a glass surface and the interactions between DPPA polar groups in the multilayer LB film structure. As a result, Y-type multilayer LB films containing DPPC could be fabricated from the mixed DPPA/DPPC monolayers with the presence of Ca2+ ions.     

α-Fe2O3纳米微粒/硬脂酸交替L-B膜的结构表征

We reported in this paper FTIR linear diehroic spectroscopy and anisotropic properties of the nanoparticulate α-Fe_2O_3-stearate alternating Langmuir-Blodgett films (Fe_2O_3-St LB films) a new inorganic-organic quantum superlattice system. A new method fitted to inorganic-organic alternating films is used to study the molecular orientation and discuss the order arrangement of the nanopartieles in the films. The the results show that a configuration of stearate ions bound to the surface of the nano-particles: COO~- group are spherically bound to the surface of the nanoparticles; the hydrocarbon chains are almost perpendicular (31°±5°) to the substrate (7 nm-Fe_2O_3-St LB films). The orientation of hydrocarbon chains and CH_2 scissors vibration show the existence of trans-zigzag planar structure for C—C broken bone of the hy7drocarbon chains, which is related to high-order structure of the alternate films.