流动注射在线富集分离-火焰原子吸收光谱法测定水体中的铬(Ⅲ)和铬(Ⅵ)

内装活性氧化铝（碱式）和阴离子交换树脂的微型柱流动注射在线富集分离水体中的铬（Ⅲ）和铬（Ⅵ），火焰原子吸收法直接检测。微型住可同时富集两种价态的离子，分别用1mol／L的NH4NO3和HNO3洗脱Cr（Ⅵ）和Cr（Ⅲ）于喷雾器中。进样时间25s，铬（Ⅵ）和铬（Ⅲ）的富集倍数分别为11倍和20倍，实际水样的加标回收率在90％～106％之间；分析速率为50个样／h；铬（Ⅵ）、铬（Ⅲ）的检出限（3δ）分别为1．5μg／L和0．7μg／L；相对标准偏差（50μg／L）分别为1．9％和2．6％。     

萃取-缝式石墨管原子捕集火焰原子吸收法测定水样中痕量锑(Ⅲ)和锑(Ⅴ)

研究了锑(Ⅲ)和锑(Ⅴ)在DDTC—MIBK体系中的萃取和反萃取行为，用缝式石墨管原子捕集技术结合火焰原子吸收法测定了水样中的痕量锑(Ⅲ)和锑(Ⅴ)，线性范围为2．0—60μg／L，检出限为0．4μg／L，特征浓度为1．5μg/L／1％吸收，相对标准偏差为2．6％，锑回收率为93．0％一105．0％。     

流动注射-化学发光法直接测定土壤中的锑(Ⅲ)

利用锑(Ⅲ)对鲁米诺-双氧水化学发光体系的催化作用,建立了一种直接测定锑(Ⅲ)的新方法.锑(Ⅲ)浓度的对数在5×10-8～5×10-5g/L范围内与发光强度呈线性关系,相关系数r=0.9991,检测限为2×10-9g/L.对5×10-8 g/L的标准溶液连续测定11次,测定结果的相对标准偏差为2.37%.将该法应用于土壤样品中锑(Ⅲ)的检测,加标回收率为90%～105%.     

铑(Ⅲ)-偶氮氯膦pA-溴酸钾褪色反应催化光度法测定痕量铑

报道了以铑（Ⅲ）催化溴酸钾氧化偶氮氯膦pA为基础测定痕量铑的催化光度分析法,建立了一种在水相中直接测定痕量铑（Ⅲ）的新方法。铑（Ⅲ）含量在5~30μg/L范围内符合比耳定律,检出限为5μg/L,本法用于铂-铑催化剂中铑的测定,结果满意。     

催化极谱法测定痕量铬的研究

本文研究了含氨介质中铬(Ⅲ、Ⅵ)-α,α’-联吡啶-亚硝酸钠体系的电化学行为。建立了测定痕最铬的方法。测定铬的范围为0.004～0.028μg/mL和0.04～0.23μg/mL,检测下限为2.0×10~(-3)μg/mL,用以测定生物样品中良量铬,变异系数为0.8%。     

在线还原富集-导数火焰原子吸收光谱法测定环境水样中铬(Ⅲ)和铬(Ⅵ)的形态

采用单阀双阳离子交换树脂微柱并联，设计了双路采样逆向洗脱在线分离富集系统，该系统与原子吸收导数测量技术相结合，实现了在线分离富集．导数火焰原子吸收光谱法同时测定水中Cr（Ⅲ）和Cr(Ⅵ），导数仪用2mV／min档位，富集lmin时，分析速度为60样/h，测定Cr（Ⅲ）和Cr(Ⅵ）的特征浓度分别为0．448μg/L和0．793μg/L(相当于1％导数吸收度)，线性范围分别为0-90和0-180μg/L；对浓度分别为10、20μg/LCr（Ⅲ）和Cr(Ⅵ）测定的相对标准偏差分别为2．85％和2．85％；检出限分别为0．855和1．7lμg/L．该法对实际水样加标回收率在94．7％．104％之间。     

铬(Ⅵ)-硫脲体系的极谱吸附波及其用于土壤中总铬和有效铬(Ⅵ)的测定

在稀硫酸介质中，在加热条件下．铬（Ⅵ）氧化硫脲的产物在单扫示波极谱仪上产生一灵敏的吸附波，峰电位为-0．33V（vs.SCE），检出限为0．1μg／L．铬（Ⅵ）浓度在0．2～200μg／L范围内与峰电流呈线性关系。本法用于土壤中总铬和有效铬（Ⅵ）的测定，结果满意。     

荧光分析法测定痕量铬(Ⅵ)

拟定了一个测定痕量铬（Ⅵ）的新的荧光分析法。在硫酸介质中,铬能氧化吡咯红Y。使其荧光猝灭,方法的检出限为2．2μg/L,线性范围为8．0－88μg/L。本法用于电镀废液、电镀液、合金钢中痕量Cr(Ⅵ）的测定,结果满意。     

利用巯基棉富集分离和鲁米诺-过氧化氢-铬(Ⅲ)化学发光体系测定水样中痕量砷

本文提出了用鲁米诺－过氧化氢－铬（Ⅲ）化学发光体系结合巯基棉时As（Ⅲ）的分离．建立了快速简单的测定水样中痕量砷的新方法。检测范围宽（0．10～1．0×104μg／L）、检测下限为3．4×102μg／L，且选择性好。直接用于环境水样的分析，5次测定的相对标准偏差为4．2％～10．6％；回收率为95％～103％。     

痕量铁的过氧化氢氧化孔雀绿催化光度法测定

基于铁（Ⅲ）对过氧化氢氧化孔雀绿反应的催化作用,提出一种高灵敏地测定痕量铁（Ⅲ）的新方法。该法线性范围为0－48μg/L,检出限为0．61μg/L。测定出水反应表观活化能Ea=37.94kJ/mol。该法用于河水、自来水样品中铁的测定,获得满意结果。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Copper catalyzed/mediated synthetic methodology for ebselen and related isoselenazolones

Scope of the copper catalyzed/mediated selenium-nitrogen coupling reaction has been studied for the synthesis of isoselenazolones. It is noticed that the 2-chloro, 2-bromo-, and 2-iodo-aryl amides substrates can be exploited in the selenium-nitrogen coupling reaction by employing 25-100 mol % of CuI/1,10-phenanthroline (L) and potassium carbonate as a base in DMF. Furthermore, electron rich 2-chloro-arylamides also underwent selenium-nitrogen coupling reaction to give biologically important selenium-nitrogen heterocycles. Also, copper-catalyzed selenium-nitrogen coupling reaction has been meticulously applied for the synthesis of diaryl diselenides having methoxy, amine, and amide functionality from respective aryl iodides in the presence of stoichiometric amount of succinimide as an external Se-N coupling partner.     

Knoevenagel condensation catalyzed by novel Nmm-based ionic liquids in water

A series of novel N-methyl morpholine (Nmm) based ionic liquids with 1,2-propanediol group were synthesized and used as catalysts for Knoevenagel condensation at room temperature in water. Under the effect of the catalyst, various aldehydes or aliphatic ketones could react with a wide range of activated methylene compounds well, including malononitrile, alkyl cyanoacetate, cyanoacetamide, β-diketone, barbituric acid, 2-arylacetonitrile and thiazolidinedione. Furthermore, most of the products could be separated just by filtrating and washing with water. Additionally, the catalyst is recyclable and applicable for the large-scale synthesis.     

Construction of polyheterocyclic spirotetrahydrothiophene derivatives via sulfa-Michael/aldol cascade reaction

A series of polyheterocyclic spirotetrahydrothiophene derivatives were obtained in moderate to excellent yields via a catalyst-free sulfa-Michael/aldol cascade reaction of chalcones 1 and commercially available 1,4-dithiane-2,5-diol 2 under mild conditions. We also present the first asymmetric sulfa-Michael/aldol cascade reaction of chalcones 1 and commercially available 1,4-dithiane-2,5-diol 2 with moderate to good enantioselectivities catalyzed by readily available chiral phase-transfer catalysts (PTCs).     

Suzuki-Miyaura reactions of the soluble guanylate cyclase inhibitor NS2028: a non-product specific route to C-8 substituted analogues

Both soluble guanylate cyclase (sGC) inhibitors ODQ 1 and NS2028 2 are synthesized via improved protocols. In the former case treating 3,4-dihydroquinoxalin-2(1H)-one oxime 8, which can be prepared in two steps from 1,2-benzenediamine, with 1,1′-carbonyldiimidazole (CDI) gives the dihydro-ODQ 10 that in the presence of KMnO₄ oxidises to give ODQ 1 in an overall yield of 46% starting from 1,2-benzenediamine. In the latter case, the synthesis affords NS2028 2 from 2-amino-4-bromophenol 3 in three steps with an overall yield of 85% and avoids the need for chromatography. Furthermore, Suzuki-Miyaura reaction conditions are described that enable the preparation of 8-aryl and 8-heteroaryl derivatives of NS2028 directly from NS2028 2. Finally, demethylation of the 8-(methoxyphenyl) substituted analogues afforded the 8-(hydroxyphenyl) derivatives 40-42. All new products are fully characterised.