Analysis of acrylamide in different foodstuffs using liquid chromatography–tandem mass spectrometry and gas chromatography–tandem mass spectrometry

Acrylamide levels over a wide range of different food products were analysed using both liquid chromatography–tandem mass spectrometry (HPLC–MS–MS) and gas chromatography–tandem mass spectrometry (GC–MS–MS). Two different sample preparation methods for HPLC–MS–MS analysis were developed and optimised with respect to a high sample throughput on the one hand, and a robust and reliable analysis of difficult matrices on the other hand. The first method is applicable to various foods like potato chips, French fries, cereals, bread, and roasted coffee, allowing the analysis of up to 60 samples per technician and day. The second preparation method is not as simple and fast but enables analysis of difficult matrices like cacao, soluble coffee, molasses, or malt. In addition, this method produces extracts which are also well suited for GC–MS–MS analysis. GC–MS–MS has proven to be a sensitive and selective method offering two transitions for acrylamide even at low levels up to 1 μg kg⁻¹. For the respective methods the repeatability (n=10), given as coefficient of variation, ranged from 3% (acrylamide content of 550 μg kg⁻¹) to 12% (acrylamide content of 8 μg kg⁻¹) depending on the food matrix. The repeatability (n=3) for different food samples spiked with acrylamide (5–1500 μg kg⁻¹) ranged from 1 to 20% depending on the spiking level and the food matrix. The limit of quantification (referred to a signal-to-noise ratio of 9:1) was 30 μg kg⁻¹ for HPLC–MS–MS and 5 μg kg⁻¹ for GC–MS–MS. It could be demonstrated that measurement uncertainties were not only a result of analytical variability but also of inhomogeneity and stability of the acrylamide in food.     

Determination of alkylphenol and bisphenol A in beverages using liquid chromatography/electrospray ionization tandem mass spectrometry

A comprehensive analytical method based on liquid chromatography electrospray ionization tandem mass spectrometry (LC–ESI–MS/MS) with negative ionization mode has been developed for measuring of alkylphenols and bisphenol A in beverage samples. Concentration and clean up of samples were performed on 200 mg OASIS HLB solid extraction cartridges. The effects of mobile phases and additives on ionization were assessed. The recoveries for each compound ranged from 76.7 to 96.9% and reproducibilities were represented as having relative standard deviation (R.S.D.) below 10%. The limits of quantification (LOQ) of the method under multiple-reaction monitoring (MRM) acquisition mode were 0.04, 0.03 and 0.2 ng L⁻¹ for 2 L of mineral drinking water and 2.0, 1.8 and 8.0 ng L⁻¹ for 50 mL of soda beverages.     

Determination of perfluorooctanesulfonate and perfluorooctanoic acid in sewage sludge samples using liquid chromatography/quadrupole time-of-flight mass spectrometry

A new method is developed for the determination of perfluorooctanesulfonate (PFOS) and perfluorooctanoic acid (PFOA) in sewage sludge samples. The analytes in sewage sludge samples are extracted by methanol and formic acid, cleaned by C18 solid-phase extraction, then separated, identified and quantitated by liquid chromatography/quadrupole time-of-flight mass spectrometry (LC–QTOF-MS). A C18 column (150 mm × 2.1 mm, 3.5 μm) with gradient elution of MeOH–H₂O (60:40) containing 5 mmol/L ammonium acetate and MeOH–H₂O (80:20) is used for the chromatographic separation. [M−K]⁻ ions at m/z 498.93 for PFOS and [M−COOH]⁻ ion at m/z 368.97 for PFOA are selected for QTOF-MS in the negative electrospray ionization mode. The detection limits for PFOS and PFOA in sewage sludge samples are 0.5 and 0.8 ng/g, respectively. The spiked recoveries are in the range of 85–114 and 71–98% for PFOS and PFOA, respectively. The proposed method is successfully applied to the analysis of PFOS and PFOA in 16 sewage sludge samples from China. PFOS and PFOA are detected in most sewage sludge samples and the concentrations of PFOS and PFOA are up to 5383 and 4780 ng/g (oven dry weight), respectively.     

Determination of polybrominated diphenyl ethers in soil by ultrasonic assisted extraction and gas chromatography mass spectrometry

An analytical method for the determination of polybrominated diphenyl ethers (PBDEs) in soil was developed. Soil samples were placed in small glass columns and PBDEs extracted from soil, with a low volume of ethyl acetate (5 mL, 2× 15 min), assisted by sonication. PBDEs were determined by gas chromatography with electron impact mass spectrometric detection in the selected ion monitoring mode (GC–MS–SIM) and residues were confirmed by their retention times, selected ions and qualifier–target abundance ratios. Recovery studies were performed at 10, 1, 0.1 and 0.05 μg/kg fortification levels, and the recoveries obtained ranged from 81 to 104% with a relative standard deviation between 1 and 9%. The detection limit of the method varied from 2 to 30 pg/g and the quantification limit ranged from 7 to 100 pg/g for the different PBDEs studied. The developed method was linear over the range assayed, 0.01–10 μg/kg with determination coefficients equal or higher than 0.997. The proposed method was used to determine PBDEs levels in soil samples from different areas of Spain and PBDEs were detected in some samples with values ranging from 1.3 to 5.6 μg/kg.     

Isolation and characterization of methoxylated flavones in the flowers of Primula veris by liquid chromatography and mass spectrometry

Characterization of six flavones, which were named substances G1, G2, G3, G4, G5 and G6 according to their R_F values in normal-phase thin-layer chromatography, is reported. The pure flavones were purified after maceration with methanol by normal-phase solid-phase extraction, normal-phase medium-pressure liquid chromatography, normal-phase preparative thin-layer chromatography and preparative reversed-phase high-performance liquid chromatography (RP-HPLC). The collected fractions of several isolation steps were analyzed by normal-phase (NP) and RP-HPLC. Detection and identification of the substances G was accomplished by UV detection at 213–216 nm, diode array UV detection, or fluorescence detection (λ_ex=330 nm; λ_em=440 nm). The molecular mass, the elementary composition, and the structure of the six components was determined by electron-impact high-resolution mass spectrometry (EI-HRMS). Substance G4 was identified as 3′,4′,5′-trimethoxyflavone. The substances G1–G6 were shown to be mono-, di- tri- and pentamethoxyflavones. HPLC–electrospray ionization tandem mass spectrometry (ESI-MS–MS) of the flavones was carried out employing a 150×2 mm I.D. column packed with a 3 μm/100 Å octadecylsilica stationary phase and a mobile phase comprising 1.0% acetic acid in water–acetonitrile (50:50). Comparative RP-HPLC–ESI-MS of the raw methanol extract and the isolated substances G1–G6 proved that the isolated compounds were pure and were not artifacts. Finally, RP-HPLC–ESI-MS–MS was used to identify substances G1–G6 in phytopharmaceutical drugs.     

Simultaneous determination of paracetamol and chlorpheniramine in human plasma by liquid chromatography-tandem mass spectrometry

An analytical method for the determination of paracetamol and chlorpheniramine in human plasma has been developed, validated and applied to the analysis of samples from a phase I clinical trial. The analytical method consists in the extraction of paracetamol and chlorpheniramine with diethyl ether, followed by the determination of both drugs by an LC–MS–MS method, using 2-acetamidophenol as internal standard. The intra-assay and inter-assay precision and accuracy of this technique were good and the limit of quantitation was 0.5 μg/ml of plasma for paracetamol and 0.2 ng/ml for chlorpheniramine. The concentration working range was established between 0.5 μg/ml and 25 μg/ml for paracetamol and between 0.2 ng/ml and 50 ng/ml for chlorpheniramine. This method has been used for analyzing more than 1200 human plasma samples from a clinical study with 24 volunteers.     

Analysis of pesticides in fruit, vegetables and cereals using methanolic extraction and detection by liquid chromatography–tandem mass spectrometry

A method for analysing carbamates and other relatively polar pesticides by LC–MS–MS with electrospray ionisation has been developed. The method is based on extraction by ultrasonication using a methanolic ammonium acetate–acetic acid buffer. After centrifugation the samples are filtered in Miniprep filter HPLC vials and detected by LC–MS–MS. To compensate for variations in the MS response [¹³C₆]-carbaryl was used as internal standard and matrix-matched pesticide solutions were used as external standards for the quantification. The method has been validated for the matrices apple, avocado, carrot, lettuce, orange, potato and wheat at the spiking levels—0.02; 0.04 and 0.20 mg kg⁻¹. Recoveries were generally in the range 70–120%. Results from participation in three intercomparisons proved the accuracy of the method. As the analytical procedure does not include any concentration or cleanup steps, it is easy and fast to perform, making it applicable for routine analysis in large pesticide monitoring programmes.     

Assessment of pesticide contamination in soil samples from an intensive horticulture area, using ultrasonic extraction and gas chromatography-mass spectrometry

In order to reduce the amount of sample to be collected and the time consumed in the analytical process, a broad range of analytes should be preferably considered in the same analytical procedure. A suitable methodology for pesticide residue analysis in soil samples was developed based on ultrasonic extraction (USE) and gas chromatography–mass spectrometry (GC–MS). For this study, different classes of pesticides were selected, both recent and old persistent molecules: parent compounds and degradation products, namely organochlorine, organophosphorous and pyrethroid insecticides, triazine and acetanilide herbicides and other miscellaneous pesticides. Pesticide residues could be detected in the low- to sub-ppb range (0.05–7.0 μg kg⁻¹) with good precision (7.5–20.5%, average 13.7% R.S.D.) and extraction efficiency (69–118%, average 88%) for the great majority of analytes. This methodology has been applied in a monitoring program of soil samples from an intensive horticulture area in Póvoa de Varzim, North of Portugal. The pesticides detected in four sampling programs (2001/2002) were the following: lindane, dieldrin, endosulfan, endosulfan sulfate, 4,4′-DDE, 4,4′-DDD, atrazine, desethylatrazine, alachlor, dimethoate, chlorpyrifos, pendimethalin, procymidone and chlorfenvinphos. Pesticide contamination was investigated at three depths and in different soil and crop types to assess the influence of soil characteristics and trends over time.     

Analytical method for the determination of the aminoglycoside gentamicin in hospital wastewater via liquid chromatography-electrospray-tandem mass spectrometry

A method for the determination of gentamicin residues in hospital wastewater has been developed using kanamycin as a surrogate standard. The method consists of solid-phase extraction (SPE) and detection by ion-pair chromatography with electrospray tandem mass spectrometry (LC–ES-tandem MS). The SPE was performed on a weak cation exchanger. Filtration should be avoided in the sample preparation, otherwise a significant loss of gentamicin occurs. Chromatographic separation on a C₁₈-column was achieved using a ternary eluent containing methanol, water and 20 mmol l⁻¹ heptafluorobutyric acid solution. Mean relative recoveries of the analytes in hospital wastewater varied between 107 and 111%. The limit of quantification (LOQ) was 0.20 μg l⁻¹ in hospital wastewater. Gentamicin was found in native hospital wastewater in a concentration range between 0.4 and 7.6 μg l⁻¹.     

Analysis of acidic drugs in the effluents of sewage treatment plants using liquid chromatography-electrospray ionization tandem mass spectrometry

Azaspiracid poisoning (AZP) is a new human toxic syndrome that is caused by the consumption of shellfish that have been feeding on harmful marine microalgae. A liquid chromatography–mass spectrometry (LC–MS) method has been developed for the determination of the three most prevalent toxins, azaspiracid (AZA1), 8-methylazaspiracid (AZA2) and 22-demethylazaspiracid (AZA3) as well as the isomeric hydroxylated analogues, AZA4 and AZA5. Separation of five azaspiracids was achieved on a C₁₈ column (Luna-2, 150×2 mm, 5 μm) with isocratic elution using acetonitrile–water containing trifluoroacetic acid and ammonium acetate as eluent modifiers. Using an electrospray ionisation (ESI) source with an ion-trap mass spectrometer, the spectra showed the protonated molecules, [M+H]⁺, with most major product ions due to the sequential loss of two water molecules. A characteristic fragmentation pathway that was observed in each azaspiracid was due to the cleavage of the A-ring at C₉–C₁₀ for each toxin. It was possible to select unique ion combinations to distinguish between the isomeric azaspiracids, AZA4 and AZA5. Highly sensitive LC–MS³ analytical methods were compared and the detection limits were 5–40 pg on-column. Linear calibrations were obtained for AZA1 in shellfish in the range 0.05–1.00 μg/ml (r²=0.9974) and good reproducibility was observed with a relative standard deviation (%RSD) of 1.8 for 0.9 μg AZA1/ml (n=5). The %RSD values for the minor toxins, AZA4 and AZA5, using LC–MS³ (A-ring fragmentation) were 12.3 and 8.1 (0.02 μg/ml; n=7), respectively. The selectivity of toxin determination was enhanced using LC–MS–MS with high energy WideBand activation.     

Analysis of glycolytic intermediates in Saccharomyces cerevisiae using anion exchange chromatography and electrospray ionization with tandem mass spectrometric detection

The purpose of this study is to selectively and quantitatively analyze several glycolytic intermediates in cells of Saccharomyces cerevisiae using high-performance anion exchange chromatography (HPAEC) coupled to electrospray ionization tandem mass spectrometry for the analysis. A sodium hydroxide gradient is used to separate the glycolytic compounds and after the column sodium hydroxide is reduced by proton exchange with a membrane device prior to introduction to the mass spectrometer. The detection limits for 10 μl samples are down to the 0.4–5 pmol range. This corresponds for the intracellular metabolites to a range of 2–20 nmol per gram biomass dry weight (DW). Standard addition did reveal some influence of the sample matrix on the measured concentrations. Separation and analysis is hardly affected by the high sulfate and phosphate concentrations (1 mM) in the fermentation medium and by the intracellular matrix. Validation of the glucose-6-phosphosphate LC–MS–MS analysis results with enzymatic analysis showed an excellent agreement between the two methods. The suitability of the method was clearly shown by analyzing a series of steady state S. cerevisiae samples from a carbon limited aerobic chemostat culture.     

Surface and wastewater quality monitoring: combination of liquid chromatography with (geno)toxicity detection,diode array detection and tandem mass spectrometry for identification of pollutants

Identification of unknown water pollutants with liquid chromatography and tandem mass spectrometry (LC–MS–MS) is often more complex and time consuming than identification with gas chromatography and mass spectrometry (GC–MS). In order to focus the identification effort on relevant compounds, unknown peaks need to be selected carefully. Based on its frequency of occurrence in the LC–Diode Array Detection (LC–DAD) chromatograms of surface and infiltrated waters, an unknown peak was selected for identification with LC–MS–MS. This compound was identified as hexamethoxymethylmelamine (HMMM), a chemical often used in the coating industry. This is the first time the presence of this chemical in surface waters has been reported. In addition to HMMM, two other structurally related compounds were found to be present in the investigated surface water. A standard mixture of HMMM and its by-products did not exhibit (geno)toxicity under the test conditions applied in this study. In another example, a genotoxic fraction of an industrial wastewater was isolated and examined by LC–MS–MS using a modern quadrupole–orthogonal acceleration-time-of-flight mass spectrometer (Q-TOF). Four compounds were detected. The structures of two compounds present are proposed to be 9-amino-2-hydroxy-acridine and 9-hydroxy-acridine-N-oxide or its structural isomer dihydroxy-acridine. Confirmation with standards could not be carried out, as pure compounds are not available. The other two compounds (structural isomers) could not be identified based on the data available within this study.     

Separation and determination of amitriptyline and nortriptyline by dispersive liquid-liquid microextraction combined with gas chromatography flame ionization detection

Dispersive liquid–liquid microextraction (DLLME) coupled with gas chromatography–flame ionization detection (GC–FID) was applied for the determination of two tricyclic antidepressant drugs (TCAs), amitriptyline and nortriptyline, from water samples. This method is a very simple and rapid method for the extraction and preconcentration of these drugs from environmental sample solutions. In this method, the appropriate mixture of extraction solvent (18 μL Carbon tetrachloride) and disperser solvent (1 mL methanol) are injected rapidly into the aqueous sample (5.0 mL) by syringe. Therefore, cloudy solution is formed. In fact, it is consisted of fine particles of extraction solvent which is dispersed entirely into aqueous phase. The mixture was centrifuged and the extraction solvent is sedimented on the bottom of the conical test tube. 2.0 μL of the sedimented phase is injected into the GC for separation and determination of TCAs. Some important parameters, such as kind of extraction and disperser solvent and volume of them, extraction time, pH and ionic strength of the aqueous feed solution were optimized. Under the optimal conditions, the enrichment factors and extraction recoveries were between 740.04–1000.25 and 54.76–74.02%, respectively. The linear range was (0.005–16 μg mL⁻¹) and limits of detection were between 0.005 and 0.01 μg mL⁻¹ for each of the analytes. The relative standard deviations (R.S.D.) for 4 μg mL⁻¹ of TCAs in water were in the range of 5.6–6.4 (n = 6). The performance of the proposed technique was evaluated for determination of TCAs in blood plasma.     

Quantitative determination of sulfonamide in meat by liquid chromatography-electrospray-mass spectrometry

This paper describes a newly developed liquid chromatography–electrospray-mass spectrometry (LC–ES-MS) method for the quantitative determination of nine commonly used sulfonamides (sulfadiazine, sulfapyridine, sulfamerazine, sulfamethazine, sulfamonomethoxine, sulfisoxazole, sulfadimethoxine, sulfaquinoaline and sulfaphenazole) in meat. [M+H]⁺ and [M+Na]⁺ were the two major ions detected in positive ion mode. Selective ion monitoring was employed for quantitative determination. Satisfactory linearity, 0.1–10 μg ml⁻¹, of each compound was obtained. Blank meat samples were fortified at levels between 50 and 500 μg kg⁻¹. [Phenyl-¹³C6]sulfamethazine was used as internal standard. Sulfonamides were isolated from meat with a solvent extraction procedure and then determined by LC–ES-MS. The limits of detection were below 10 μg kg⁻¹. The application of this newly developed method was demonstrated by analyzing various beef, pork and chicken samples from local markets.     

Solid-phase extraction of polar hydrophilic aromatic sulfonates followed by capillary zone electrophoresis-UV absorbance detection and ion-pair liquid chromatography-diode array UV detection and electrospray mass spectrometry

A comprehensive comparison of four different polymeric solid-phase extraction (SPE) materials for the extraction of 22 different aromatic sulfonates of environmental concern was performed. The investigated adsorbents were the polystyrene–divinylbenzene materials LiChrolut EN from Merck, Isolute ENV+ from International Sorbent Technology, HR-P from Macherey–Nagel and the new Oasis HLB poly(divinylbenzene-co-N-vinylpyrrolidone) copolymer from Waters. Different SPE parameters like the elution solvent and the drying step of the cartridges were optimized. Analyses were performed by capillary zone electrophoresis–UV absorbance detection (CZE–UV) and ion-pair liquid chromatography–diode array UV detection coupled in series with electrospray mass spectrometry (IP-LC–DAD-ESI-MS) in the negative ionization mode. LC–MS offers a higher separation efficiency than CZE. The best adsorbents were LiChrolut EN and HR-P followed by Isolute ENV+ and Oasis HLB. The recoveries for most of the onefold negatively charged aromatic sulfonates were >50% for the extraction from spiked ground water at 50 μg/l. Recoveries for LiChrolut EN and HR-P were approximately 20% higher than for Isolute ENV+. Very hydrophilic sulfonates containing more than one negative sulfonate group could not be extracted by any of the tested adsorbents.     

高通量固相萃取-超高效液相色谱-串联质谱法测定人尿中8种环境酚类内分泌干扰物

建立了人尿中8种环境酚类化合物的96孔板固相萃取-超高效液相色谱-串联质谱(96-well SPE LC-MS/MS)检测方法,其中包括7种双酚类化合物和三氯生。尿样解冻到室温,经β-葡萄糖醛酸苷肽酶/芳基磺酸酯酶37 ℃过夜酶解。实验比较了3种96孔板固相萃取柱和不同淋洗条件对人尿样的净化效果和目标化合物的回收率。结果显示,采用Oasis HLB 96孔板(60 mg)对样品进行萃取和用30%(v/v)乙腈水溶液进行淋洗净化的纯化效果最好。纯化后目标物用甲醇溶液洗脱,经氮气吹干,用0.5 mL甲醇-水(1∶1, v/v)溶液定容,目标化合物用UPLC-MS/MS进行检测。比较了2种分析柱(C₁₈和T3分析柱)以及不同的有机流动相对分离样品中目标物的影响。结果显示,以BEH C₁₈(100 mm×2.1 mm, 1.7 μm)作为分析柱,乙腈/水作为流动相,以流速0.3 mL/min梯度洗脱时,目标物的分离效果最好。质谱条件选择串联质谱负离子电喷雾(ESI^-)多反应监测模式(MRM)进行检测。对样品的基质效应进行评估发现,双酚A、双酚F、双酚S、双酚B和双酚AF的绝对基质效应为3.47%~15.32%,不需要补偿措施;四氯双酚A、四溴双酚A和三氯生的绝对基质效应分别是49.58%(中等基质效应)、71.99%和86.93%(强基质效应),均需要补偿效应。因此,该方法采用了一一对应的同位素内标法抵消基质效应。用6份实际尿样基质评估相对基质效应,8种内标的峰面积的相对标准偏差为3.63%~9.06%,说明相对基质效应稳定。在优化条件下,双酚A和双酚AF在0.50~50 μg/L内、四氯双酚A和双酚S在0.05~50 μg/L内、双酚F和四溴双酚A在0.01~50 μg/L内、双酚B在1.00~50 μg/L内、三氯生在5.00~200 μg/L内线性关系良好,相关系数大于0.9995。方法检出限为0.002~1.09 μg/L,定量限为0.007~3.63 μg/L。3个加标水平的加标回收率为81.0%~101.9%,日内精密度为0.4%~19.4%,日间精密度为2.5%~17.8%。应用该方法对2019-2020年采集的北京地区64份尿样进行测定,结果发现8种目标分析物中,除双酚B和双酚AF未检出外,其余均有检出,其中双酚A和双酚S的检出率最高,分别为100%和96.9%。三氯生、四溴双酚A、四氯双酚A和双酚F的检出率分别为57.8%、46.9%、23.4%和21.9%。尿样中8种目标物含量的中位值以降序排列分别为1.44 μg/L(三氯生)、0.69 μg/L(双酚A)、0.086 μg/L(双酚S)、0.0032 μg/L(四溴双酚A)、0.00050 μg/L (四氯双酚A)、0.00 μg/L(双酚F、双酚B和双酚AF)。以上尿样检测结果显示,北京市居民存在普遍的环境酚类化合物暴露,值得关注。该方法操作简单,定量准确,样品需求量小,有机试剂消耗少,适合大批量样本的测定。     

Quantitation of anabolic hormones and their metabolites in bovine serum and urine by liquid chromatography-tandem mass spectrometry

A specific and sensitive method based on tandem mass spectrometry with on-line high-performance liquid chromatography using atmospheric pressure chemical ionisation (LC–APCI-MS–MS) for the quantitation of anabolic hormone residues (17β-19-nortestosterone, 17β-testosterone and progesterone) and their major metabolites (17-19-nortestosterone and 17-testosterone) in bovine serum and urine is reported. [²H₂]17β-Testosterone was used as internal standard. The analytes were extracted from urine (following enzymatic hydrolysis) and serum samples by liquid–liquid extraction and purified by C₁₈ solid-phase extraction. Ionisation was performed in a heated nebulizer interface operating in the positive ion mode, where only the protonated molecule, [M+H]⁺, was generated for each analyte. This served as precursor ion for collision-induced dissociation and two diagnostic product ions for each analyte were identified for the unambiguous hormone confirmation by selected reaction monitoring LC–MS–MS. The overall inter-day precision (relative standard deviation) ranged from 6.37 to 2.10% and from 6.25 to 2.01%, for the bovine serum and urine samples, respectively, while the inter-day accuracy (relative error) ranged from −5.90 to −3.18% and from −6.40 to −2.97%, for the bovine serum and urine samples, respectively. The limit of quantitation of the method was 0.1 ng/ml for all the hormones in bovine serum and urine. On account of its high sensitivity and specificity the method has been successfully used to confirm illegal hormone administration for regulatory purposes.     

Determination of N-acetylcysteine in human plasma by liquid chromatography coupled to tandem mass spectrometry

An analytical method for the determination of total N-acetylcysteine in human plasma has been developed, validated and applied to the analysis of samples from a phase I clinical trial. The analytical method consists of plasma digestion with dithiothreitol in order to reduce all the oxidized forms of N-acetylcysteine, and extraction with ethyl acetate followed by determination of levels by an LC–MS–MS method. The intra- and inter-assay precision and accuracy of this technique were good and the limit of quantitation was 50 ng/ml of plasma. The concentration working range was established between 50 ng/ml and 1000 ng/ml. This method has been used in the analysis of approximately 800 human plasma samples from a clinical study with 24 volunteers; the precision of the quality controls was in the range 8.7 to 13.4% and the accuracy was in the range −5.9 to 8.5%, expressed as the RSD and the relative error, respectively.     

Comparison between liquid chromatography-UV detection and liquid chromatography-mass spectrometry for the characterization of impurities and/or degradants present in trimethoprim tablets

The characterization of impurities and/or degradants present in pharmaceutical compounds is an important part of the drug development process. Although LC–UV is commonly employed for impurities and degradant compound determination, LC–MS techniques are proposed in this work to be a viable modern alternative for the characterization of these compounds. LC–UV and LC–MS were compared for the detection of impurities present in different brands of trimethoprim tablets by using an in-line LC–UV–MS system with atmospheric pressure chemical ionization source (APCI) coupled with a reversed-phase gradient HPLC system. It was shown that, although chemical noise was higher when using full-scan LC–MS compared to LC–UV, low level impurities were better detected by mass spectrometry (MS) when modern software algorithms are employed. These included the “Contour” chromatogram algorithm and/or the “component detection algorithm” (CODA). In addition, MS allowed for the simultaneous determination of the molecular masses and some structural information of the impurities and/or degradants. The results also showed a large difference in the purity of trimethoprim among different manufacturers. LC–MS and tandem MS techniques were employed to acquire fragmentation patterns for trimethoprim and its degradants to gain insight into their structures.     

Determination of nonylphenol ethoxylates in the aquatic environment by normal phase liquid chromatography-electrospray mass spectrometry

A comprehensive analytical method based on normal-phase liquid chromatography–electrospray ionization mass spectrometry (NPLC–ESI-MS) has been established for determination of nonylphenol ethoxylates (NPEOs) in the aquatic environment. Extraction and cleanup of samples were performed on graphitized carbon black (GCB) solid-phase extraction cartridges. Complete separation between each individual NPEOs was achieved by combining a C₁₈ pre-column with a silica analytical column and using acetonitrile–water as eluent. Quantitative determination by LC–ESI-MS was achieved in the positive ionization (PI) mode at a ramped cone voltage for NPEOs using selected ion monitoring. Recoveries for NPEOs ranged between 91.9 and 117.5%, and the limits of detection varied between 0.5 and 2 ng/l for individual NPEOs with n longer than 2, and between 5 and 0.5 μg/l for NP1EO and NP2EO. This method was successfully applied to the investigation of residual NPEOs with n>2 in the Chongqing area of the Changjiang river. NPEOs with n ranging from 1 to 22 were found to vary between 0.1 and 2900 ng/l with a distribution depending on the depth of water.