流动注射化学发光抑制法测定抗坏血酸

基于抗坏血酸对Ｌｕｍｉｎｏｌ－ＫＩＯ４－Ｈ２Ｏ２体系化学发光反应的抑制作用,建立了化学发光抑制快速测定抗坏血酸的新方法。该方法线性范围为１．０＊１０＾－７－１．０＊１０＾－５ｍｏｌ／Ｌ,检出限为６．０＊１０＾－８ｍｏｌ／Ｌ,对８．０＊１０＾－７ｍｏｌ／Ｌ抗坏血酸１１次平行测定的相对标准偏差为１．０％。用于维生素Ｃ片剂及注射液中抗坏血酸含量的测定,结果令人满意。     

Cathodic adsorptive stripping square-wave voltammetric determination of nifedipine drug in bulk,pharmaceutical formulation and human serum

Nifedipine is a calcium-channel antagonist drug used in the management of angina pectoris and hypertension through inhibition of calcium influx. A fully validated sensitive cathodic adsorptive stripping square-wave voltammetry procedure was optimized for the determination of the drug at trace levels. The procedure was based on the reduction of the nitrophenyl group after the interfacial accumulation of the drug onto a hanging mercury drop electrode in Britton-Robinson buffer of pH 11.0. The optimal conditions of the procedure were found to be: accumulation potential=-0.9 V vs. Ag/AgCl/KCl(s)), accumulation time=30 s, scan increment=10 mV, pulse amplitude=50 mV and frequency=120 Hz. Under these conditions, a well-defined peak was obtained; its peak current showed a linear dependence on drug concentration in the range of 2x10(-9)-2x10(-7) mol L(-1) bulk nifedipine. The mean recoveries based on eight replicate measurements for 1x10(-8) and 5x10(-8) mol L(-1) bulk nifedipine solutions were 98.46+/-0.86% and 98.23+/-0.92%, respectively. A detection limit of 3.42x10(-10) mol L(-1) bulk nifedipine was achieved. The procedure was successfully applied for assay of the drug in tablets and spiked human serum with mean recoveries of 101.95+/-1.42% and 98.70+/-0.63%, respectively. The limit of detection of the drug in spiked human serum was found to be 3.90x10(-10) mol L(-1).     

多壁碳纳米管修饰电极检测盐酸氯丙嗪的研究

制备了多壁碳纳米管修饰玻碳电极,采用循环伏安法(CV)研究了盐酸氯丙嗪在修饰电极上的电化学特性,发展了一种新的检测盐酸氯丙嗪的电化学分析方法。在最佳实验条件下,用循环伏安法检测盐酸氯丙嗪,其响应电流与盐酸氯丙嗪的浓度在8.0×10-5~1.0×10-3mol/L范围内有很好的线性关系,线性方程为Ip(A)=0.0106c(mol/L)-8×10-8(R2=0.999,n=6),检出限为6.2×10-6mol/L(S/N=3)。方法可用于盐酸氯丙嗪片的测定。     

Construction and performance characteristics of new fentanyl-selective plastic membrane electrode.

The construction and performance characteristics of an ion-selective electrode for fentanyl-drug cation, based on an ion-pair complex with tetrakis[3,5-bis-(trifluoromethyl)phenyl]borate anion in a PVC matrix were studied. A linear response for 1 x 10(-5) mol dm-3 to 1 x 10(-2) mol dm-3 drug with a slope of 57.9 +/- 0.5 mV/decade was established. The optimum pH range was 2 to 6. The lower detection limit was 6.29 x 10(-6) mol dm-3 fentanyl citrate (2.1165 micrograms cm-3 fentanyl). There were negligible interferences from a number of inorganic cations, structural analogues, and some common drug additives in injections. The electrode proposed has been successfully applied to determine fentanyl citrate in injections. The results correlated well with those obtained by the United States Pharmacopoeia standard procedure.     

Square-wave adsorptive cathodic stripping voltammetric determination of anti-inflammatory indomethacin drug in tablets and human serum at a mercury electrode

Indomethacin is a non-steroidal anti-inflammatory drug possessing anti-pyretic and analgesic properties. A fully validated square-wave adsorptive cathodic stripping voltammetric procedure is described for determination of indomethacin. The procedure was based on the reduction of the C=O double bond of the drug molecule in Britton-Robinson buffer (pH 4) after its preconcentration onto the mercury electrode surface. The optimized conditions of the procedure were: frequency 120 Hz, scan increment 10 mV, pulse amplitude 50 mV, preconcentration potential -0.9 V (vs. Ag/AgCl/KCl(s)) and preconcentration time 90 s. The proposed procedure was successfully applied for determination of the drug in tablets and human serum with good recoveries. The limits of detection in bulk form and human serum were 6.7 x 10(-10) mol L(-1) and 8.1 x 10(-10) mol L(-1), respectively.     

Adsorptive behavior and electrochemical determination of the anti-fungal agent ketoconazole

The adsorptive properties and electrochemical behavior of ketoconazole, an oral anti-fungal agent, are demonstrated at a glassy carbon electrode. The adsorption of the compound obeys the Frumkin isotherm with an interaction factor (alpha) of 0.985 and adsorptive coefficient (beta) of 1.98 x 10(6) L mol(-1). The Gibbs energy of adsorption (deltaG) is -3.59 x 10(4) J mol(-1) at 25 degrees C. A very sensitive electroanalytical method has been developed for determination of the drug with a detection limit of 4.0 x 10(-11) mol L(-1). Relationships between stripping current and concentration of ketoconazole were linear in the range 10(-6)-10(-10) mol L(-1) with different preconcentration periods. The method has been used to measure the ketoconazole content of tablets.     

Voltammetric determination of mifepristone at a DNA-modified carbon paste electrode

A new strategy for the preparation of a DNA-modified carbon paste electrode is developed. It is found that the anodic response of mifepristone is greatly enhanced at the dsDNA-modified carbon paste electrode comparing with that obtained at the bare electrode, while the response at a ssDNA-modified electrode is similar to bare electrode. So the dsDNA-modified electrode is employed as a sensitive biosensor for the detection of mifepristone. A linear dependence of the peak currents on the concentration is observed in the range 2.0 x 10(-7) approximately 2.0 x 10(6) mol/L, with a detection limit of 1.0 x 10(-7) mol/L. The relative standard deviation is 4.3% for six successive determinations of 1.0 x 10(6) mol/L mifepristone. The determination of mifepristone tablets is carried out and satisfactory results are obtained.     

New technique for capillary electrophoresis directly coupled with end-column electrochemiluminescence detection

A new end-column electrochemiluminescence (ECL) detection technique coupling to capillary electrophoresis (CE) is characterized. A 300 microm diameter Pt working electrode was used to directly couple with a 75 microm inner diameter separation capillary without an electric field decoupler. The hydrodynamic cyclic voltammogram (CV) of Ru(bpy) 3 2+ showed that electrophoretic current did not affect the ECL reaction. The presence of high-voltage (HV) field only resulted in the shift of the ECL detection potential. The distance of capillary to electrode was an important parameter for optimizing detection performance as it determined the characteristics of mass transport toward the electrode and the actual concentration of Ru(bpy) 3 2+ in the detection region. The optimum distance of capillary to electrode was decided by the inner diameter of the capillary, too. For a 75 microm capillary, the working electrode should be placed away from the capillary outlet at a distance within the range of 220-260 microm. The effects of pH value of ECL solution and molecular structure of analytes on peak height and theoretical plate numbers were discussed. Using the 75 microm capillary, under the optimum conditions, the method provided a linear range for tripropylamine (TPA) between 1 x 10(-10) and 1 x 10(-5) mol/L with correlation coefficient of 0.998. The detection limit (signal-to-noise ratio S/N = 3) was 5.0 x 10(-11) mol/L. The relative standard deviation in peak height for eight consecutive injections was 5.6%. By this new technique lidocaine spiked in a urine sample was determined. The method exhibited the linear range for lidocaine from 5.0 x 10(-8) to 1.0 x 10(-5) mol/L with correlation efficient of 0.998. The limit of detection (S/N = 3) was 2.0 x 10(-8) mol/L.     

Amperometric determination of glutathione and cysteine on a Pd-IrO(2) modified electrode with high performance liquid chromatography in rat brain microdialysate

A Pd/IrO(2) co-electrodeposited glassy carbon electrode was prepared and the electrochemical behavior of glutathione (GSH) at this chemically modified electrode (CME) has been studied by cyclic voltammetry (CV). The results indicated that the modified electrode efficiently exhibited electrocatalytic oxidation for GSH with relatively high sensitivity, stability, and long-life. Coupled with high-performance liquid chromatography (HPLC), the Pd/IrO(2) modified electrode was utilized for the electrochemical detection (ECD) of the thiocompounds, glutathione and cysteine (Cys). The peak currents were linear with the substance concentrations in the range of 1.0 x 10(-5) mol L(-1) to 8.0 x 10(-4) mol L(-1) for GSH and 4.0 x 10(-6) mol L(-1) to 2.0 x 10(-4) mol L(-1) for Cys. The detection limits were 2.0 x 10(-6) mol L(-1) for GSH and 5.0 x 10(-7) mol L(-1) for Cys with S/N of 3. The method has been successfully applied to assess the contents of GSH and Cys in rat brain microdialysates.     

Determination of trace procaine hydrochloride by differential pulse adsorptive stripping voltammetry with a Nafion modified glassy carbon electrode.

A sensitive and selective method for the determination of procaine hydrochloride with a Nafion-modified glassy carbon electrode has been developed. The voltammetric behavior of procaine hydrochloride on the Nafion-modified electrode indicated that the modified electrode not only increased the sensitivity of the determination of procaine hydrochloride, but also catalyzed the electrode process. Procaine hydrochloride was accumulated in Britton-Robinson buffer (pH 2.09) at a potential of -0.2 V (vs. SCE) for 180 s, and was then determined by differential pulse adsorptive stripping voltammetry. The effect of various parameters, such as the pH of the medium, the mass of drop-coated Nafion, the accumulation potential, the accumulation time and the scan rate, were investigated. Under the optimum conditions, a linear calibration graph was obtained in the concentration range of 6.0 x 10(-8) to 6.0 x 10(-6) mol l(-1) with a correlation coefficient of 0.9987. The relative standard deviation was 4.18% for eight successive determinations of 1.0 x 10(-7) mol l(-1) procaine hydrochloride, and the detection limit (three times signal to noise) was 7.0 x 10(-9) mol l(-1). A study of interfering substances was also performed, and the method was applied to the direct determinations of procaine hydrochloride in the injection solution of procaine hydrochloride and in rabbit serum.     

Determination of dissociation constants of cyclodextrin-ligand inclusion complexes by electrospray ionization mass spectrometry

The inclusion complexes of four ligands binding to cyclodextrins (CDs) were studied by electrospray ionization mass spectrometry (ESI-MS) and the dissociation constants of the complexes were obtained. The 1:1 stoichiometric inclusion complex was found in the system of CD and fenbufen or aspirin. The obtained KD values of the inclusion complexes of fenbufen binding to alpha-CD and to beta-CD are 4.38x10(-4) mol L(-1) and 2.12x10(-4) mol L(-1), respectively. The KD values of the inclusion complexes of alpha-CD-aspirin and beta-CD-aspirin are 3.33x10(-4) mol L(-1) and 1.83x10(-4) mol L(-1), respectively. A non-linear least squares regression method was applied to validate the results which were consistent with each other. For the system of tetracycline hydrochloride and CD, the 1:1 and 1:2 stoichiometric inclusion complexes were found in the mass spectra. The KD,1 and KD,2 values of the 1:1 and 1:2 stoichiometric inclusion complexes of alpha-CD and tetracycline hydrochloride are 4.47x10(-4) mol L(-1) and 6.51x10(-4) mol L(-1), respectively, and those of beta-CD and tetracycline hydrochloride are 2.26x10(-4) mol L(-1) and 8.57x10(-4) mol L(-1), respectively. For the system of norfloxacin and CD, besides the 1:1 and 1:2 inclusion complexes, the 1:3 stoichiometric inclusion complex was also found. The KD,1, KD,2 and KD,3 of alpha-CD and norfloxacin inclusion complexes are 4.61x10(-4) mol L(-1), 6.05x10(-4) mol L(-1) and 1.45x10(-3) mol L(-1), respectively. The three KD values of beta-CD and norfloxacin are 1.96x10(-4) mol L(-1), 4.93x10(-4) mol L(-1) and 1.15x10(-3) mol L(-1), respectively.     

盐酸雷尼替丁印迹聚合物膜电极的制备与应用

研究了盐酸雷尼替丁印迹聚合物离子选择性电极的制备、特性及应用。该电极在1.0×10-5～1.0×10-2mol/L范围内表现能斯特响应,斜率为-28.18mV/pC,检测下限为5.2×10-6mol/L,原料回收率为96.8%～104.6%。该电极与先前报道的电极相比,具有更高的选择性、灵敏性和抗干扰性。利用该电极对雷尼替丁原料、胶囊含量进行了测定,结果与药典法一致。     

Coated-wire copper(II)-selective electrode based on phenylglyoxal-α-monoxime ionophore

A copper(II) ion-selective electrode based on a recently synthesized 2-quinolyl-2-phenylglyoxal-2-oxime (phenylglyoxal-alpha-monoxime) has been developed. The PVC-based membrane containing phenylglyoxal-alpha-monoxime, dibutyl phthalate as plasticizer, and sodium tetraphenylborate as anion excluder and membrane modifier, was directly coated on the surface of a platinum-wire electrode. The response of the electrode was linear with a near-Nernstian slope of 28.2 mV decade(-1) within the Cu2+ ion concentration range 1x10(-6)-1x10(-1) mol x L(-1). The response time for the proposed electrode to achieve a 95% steady potential for Cu2+ concentrations ranging from 1x10(-1) to 1x10(-6) mol x L(-1) is between 10 and 50 s, and the electrode is suitable for use within the pH range of 3 to 6.5. The electrode has a detection limit of 5x10(-7) mol x L(-1) Cu2+ and its selectivity relative to several alkali, alkaline earth, transition, and heavy metal ions was good. The coated-wire electrode could be used for at least two months without a considerable alteration of its potential. Applications of the electrode for determination of copper in milk powder samples and as an indicator electrode for potentiometric titration of Cu2+ ion using EDTA are reported.     

Carbon paste electrode modified with copper(II) phosphate immobilized in a polyester resin for voltammetric determination of <Emphasis Type="SmallCaps"> l </Emphasis>-ascorbic acid in pharmaceutical formulations

A carbon paste electrode modified with copper(II) phosphate immobilized in a polyester resin (CuP-Poly) is proposed for voltammetric determination of L-ascorbic acid in pharmaceutical formulations. The modified electrode allows the detection of L-ascorbic acid at lower anodic potentials than observed at unmodified electrodes. Several parameters that can influence the voltammetric response of the proposed electrode such as carbon paste composition, pH, scan rate, and possible interference were investigated. The peak current was proportional to the concentration of ascorbic acid in the range 2.0 x 10(-5) to 3.2 x 10(-3) mol L(-1) with a detection limit of 1.0 x 10(-5) mol L(-1). The stability and repeatability of the electrode for the determination of L-ascorbic acid are also discussed. Amperometric response was also recorded for electrocatalytic oxidation of the L-ascorbic acid. Concentrations of the vitamin C in pharmaceutical formulations (tablets) measured using the modified electrode and a titrimetric method are in agreement at the 95% confidence level and within an acceptable range of error.     

盐酸依匹斯汀PVC膜电极的研制及应用

以四苯硼酸钠与盐酸依匹斯汀生成的离子缔合物为电活性物质,研制了盐酸依匹斯汀PVC膜选择性电极。在pH 5的HCl-NaOH溶液中,电极的线性范围为6.3×10-7~1.0×10-1mol/L,斜率为49 mV/pC(10℃),检出限为1.89×10-7mol/L。应用此电极测定药物中盐酸依匹斯汀含量,RSD3%,回收率为97.5%~100.2%。     

Amitriptyline-selective plastic membrane sensors and their pharmaceutical applications.

The construction and general performance characteristics of potentiometric amitriptyline-plastic membrane sensors, based on ion-pair complexes with triphenylstilbenylborate and tetra(2-chlorophenyl)borate, respectively, are described. Both electrodes show near-Nernstian responses over the range 1 x 10(-2)-7 x 10(-6) mol dm-3 with a detection limit of about 5 x 10(-6) mol dm-3. The electrodes proved useful in the determination of amitriptyline hydrochloride in pure drug substances and pharmaceutical preparations. They were also applied to the determination of content uniformity and dissolution rate of sugar-coated amitriptyline tablets. The physical processes were numerically simulated by typical equations.     

Determination of hesperidin and synephrine in Pericarpium Citri Reticulatae by capillary electrophoresis with electrochemical detection

A method based on capillary electrophoresis with electrochemical detection (CE-ED) has been developed for the determination of hesperidin (HP) and synephrine (SP) in the Chinese traditional herbal drug, Pericarpium Citri Reticulatae, the dried rind of the ripe fruits of Citrus reticulata Blanco (mandarin orange). The effects of some important factors such as the acidity and concentration of running buffer, separation voltage, and detection potential were investigated to determine the optimum conditions. The working electrode was a 300 microm diameter carbon disc electrode positioned opposite the outlet of the capillary. Both analytes could be well separated within 5 min in a 40 cm long capillary at a separation voltage of 12 kV in 50 mmol L(-1) borate buffer (pH 9.0). Excellent linearity was observed for the dependence of peak current on analyte concentration in the range from 2.5 x 10(-6) to 1.0 x 10(-3) mol L(-1) for SP and from 5.0 x 10(-6) to 1.0 x 10(-3) mol L(-1) for HP. The detection limits (S/N=3) for SP and HP were 4.96 x 10(-7) mol L(-1) and 6.54 x 10(-7) mol L(-1), respectively. This method has been successfully applied for the analysis of real samples, with satisfactory results.     

Voltammetric determination of cadmium(II) using a chemically modified electrode

An 1-(pyridylazo)-2-naphthol modified glassy carbon electrode has been investigated as sensor for the measurement of trace levels of Cd2+. Cd2+ is deposited on the surface of a PAN modified glassy carbon electrode at -1.10 V (vs. SCE) via forming Cd2+-PAN and subsequent reduction at the electrode. In the following step, Cd-PAN is oxidized, and voltammograms are recorded by scanning the potential in a positive direction. Calibration plots were found to be linear in the range 2 x 10(-8) mol/L to 8 x 10(-7) mol/L. The detection limit was 5 x 10(-10) mol/L, and the coefficient of variation, determined on one single electrode at a concentration of 5 x 10(-7) mol/L, was calculated to be 3.2% (n = 5). Using this new kind of modified electrode, trace levels of Cd(II) in water samples were determined; the average recovery was calculated to be 98.78%.     

Simultaneous electrochemical determination of xanthine and uric acid at a nanoparticle film electrode

A sensitive electrochemical method was developed for simultaneous determination of uric acid (UA) and xanthine (XA) at a glassy carbon electrode modified with multi-wall carbon nanotubes (MWNTs) film. The oxidation peak currents of UA and XA were increased at the MWNTs film electrode significantly. The experimental parameters, which influence the peak currents of UA and XA, such as the amount of MWNTs on the glassy carbon electrode, the pH of the solution, accumulation time, and scan rate, were optimized. Under optimum conditions, the peak currents were linear to the concentration of UA over the wide range from 1 x 10(-7) mol L(-1) to 1 x 10(-4) mol L(-1) and to that of XA over the wide range from 2 x 10(-8) mol L(-1) to 2 x 10(-5) mol L(-1). The interferences studies showed that the MWNTs-modified electrode exhibited excellent selectivity in the presence of ascorbic acid, dopamine, and hypoxanthine. The proposed procedure was successfully applied to detect UA and XA in human serum without any preliminary treatment.     

Flow injection determination of bromide ion in a developer using bromide ion-selective electrode detector

A potentiometric flow injection determination method for bromide ion in a developer was proposed, by utilizing a flow-through type bromide ion-selective electrode detector. The sensing membrane of the electrode was Ag(2)S-AgBr membrane. The response of the electrode detector as a peak-shape signal was obtained for injected bromide ion in a developer. A linear relationship was found to exist between peak height and the concentration of the bromide ion in a developer in a concentration range from 1.0x10(-3) to 1.0x10(-2) mol l(-1). The relative standard deviation for 10 injections of a 6x10(-3) mol l(-1) bromide ion in a developer was 1.3% and the sampling rate was ca 17-20 samples h(-1). The present method was free from the interference of an organic reducing reagent, an organic substance in a developer sample solution for the determination of bromide ion in a developer.