聚天冬氨酸与木质素磺酸钠复配物对碳酸钙阻垢性能的研究

通过静态阻垢法研究了国产聚天冬氨酸(PASP)、木质素磺酸钠(SLS)添加量对碳酸钙的阻垢性能.结果表明:PASP在5.0mg/L时阻垢率接近100%,SLS达300mg/L以上时阻垢率趋于平缓,浓度为600mg/L时,其阻垢率仍不足70%.PASP与SLS复合配方及在不同影响因素条件下阻垢性能的研究表明:复合配方(PASP 2.0mg/L SLS 5.0mg/L)的阻垢率接近100%,且适用于高钙、高pH值、高温的水系统中,并可在水系统中长时间停留.     

Engineering superlyophobic surfaces as the microfluidic platform for droplet manipulation

We propose robust engineering superlyophobic surfaces (SLS) as a universal microfluidic platform for droplet manipulation enabling electric actuation, featured with characteristics of highly nonwetting, low adhesion, and low friction for various liquids including water and oil. To functionalize SLS with embedded electrodes, two configurations with continuous and discrete topologies have been designed and compared. The discrete configuration is found to be superior upon comparison of their fabrication, microstructures and nonwetting performances. We also present new formulation of SLS pressure stability for linear, square and hexagonal pattern layouts, and propose a criterion for three wetting states (the Cassie-Baxter, partial Cassie-Baxter and Wenzel states) by introducing two dimensionless parameters, which are supported by our experimental data. Droplet manipulation experiments including deformation and transport on electrode-embedded SLS were performed, showing that present SLS reduce adhesion and flow resistance of oil droplets respectively by 98% and 73% compared with a smooth hydrophobic surface, and the excellent hydrodynamic performances are applicable for a wide range of droplet velocity. Simulation of an oil droplet electrically actuated on SLS predicts the significantly increased droplet motion for a low solid fraction and a relatively large droplet size.     

Absorption spectra of 7, 7, 8, 8-tetracyanoquinodimethane in micellar solutions.

The absorption spectra of 7, 7, 8, 8-tetracyanoquinodimethane (TCNQ) with nonionic surfactant. Triton X-100, anionic surfactant, SLS and cationic surfactant, CTAB in aqueous and nonaqueous media have been studied. The spectral studies show that TCNQ forms 1:1 charge-transfer (CT) complex with Triton X-100 in both media. The aqueous solution of TCNQ shows an absorption maxima at 610 nm, which is unperturbed in the presence of SLS but is shifted to 650 nm in the presence of CTAB, indicating the interaction of TCNQ with the cationic surfactant and not with the anionic surfactant. In addition to this, the stability of TCNQ-Triton X-100 complex has been determined and the probable site of CT interaction has been pointed out.     

Nucleation in premicellar aggregation

The role of a nucleating agent (cholesterol) in the premicellar aggregation of sodium lauryl sulfate (SLS), cetyltrimethylammonium bromide, Triton X-405 and Brij 35 has been investigated. The I(1)/I(3) ratios of pyrene in the solutions indicate that SLS is strongly nucleated by cholesterol, but the other detergents appear to be so to a lesser extent. However, quenching studies show that premicellar Brij 35 also forms nucleated aggregates that protect the probe from the quencher. Energy transfer data with Triton X-405 suggest that such aggregates have a more open structure than self-assembling ones and are more accessible to water.     

THE EFFECTS OF MIXED MICELLES OF SURFACTANTS ON POLYMERIZATION OF ACRYLAMIDE

The polymerization of acrylamide in mixed micellar solutions of surfactants, initiated by NaHSO₃ has been studied at 20 and 3Q° C with time variable method of thermokinetics for 1. 5-order reaction. The results indicate that the mixed micellar systems of cationic or anionic with zwitterionic surfactants (SLS/ CTAB, SLS/ TTAB, SLS/ SDS) and cationic with nonionic surfactants (Brij 357sol; CTAB, Bri-J35/TTAB, Brij35/ DTAB) have catalytic effect on the polymerization in the order, at 20° C. SLS/ SDS SLS/ TTAB SLS/ CTAB Brij35/ CTAB at 30° C SLS/ SDS SLS/ TTAB≈ / CTAB Bri-j35/ DTAB= sBrij35/ TTAB as Brij35/ CTAB, while Brij35/ SDS mixed micellar system has inhibition. These effects are attributed to the effect of the Stern layer of mixed micelles on the step of initiator (HSOT) to form free radical.     

A strand-loop-strand structure is a possible intermediate in fibril elongation: long time simulations of amyloid-beta peptide (10-35)

A total of 6.2 micros molecular dynamics simulations of amyloid-beta (10-35) (Abeta) were performed in explicit water solvent. The results reveal that the collapsed-coil (cc) structure determined by experiments is stable at pH 5.6 for hundreds of nanoseconds, but it can exchange with a strand-loop-strand (SLS) structure on the microsecond time scale. The SLS structure has D23-K28 as a reverse loop and the central hydrophobic core and the C-terminal in hydrophobic contact. This SLS structure topologically resembles the proposed monomer conformation in fibrils. Since it has been suggested that a special conformation of Abeta is needed when the monomer binds to fibril ends to elongate fibrils, we propose that the SLS structure may be an important intermediate binding structure for Abeta fibril growth. Simulations at pH 2.0, which is used to mimic the mutation of E22Q and D23N, and at high temperature (400 K) indicate that the SLS structure is considerably populated under these conditions while the cc structure is disrupted. These results imply that the SLS structures may also be a binding intermediate in other conditions such as E22Q and/or D23N mutations and high temperature, which have been proved to promote fibril formation previously.     

γ-radiation-initiated emulsion polymerization of n-butyl acrylate and of methyl methacrylate

We have investigated the γ-radiation-initiated polymerization of n-butyl acrylate (BA) and of methyl methacrylate (MMA) in aqueous emulsions stabilized with sodium lauryl sulfate (SLS). The reaction rate, as measured by a nonabsolute thermocouple technique, varies as the square root of emulsifier concentration for both monomers. In the case of BA, the dose rate exponent of the reaction rate is 0.7 ± 0.3, whereas the corresponding value for MMA is approximately 0.4. The overall activation energy of the BA polymerization is close to zero, whereas for MMA a value of 4.8 ± 2.1 kcal/mole has been found. The poly(butyl acrylate) molecular weight is effectively independent of soap concentration and of dose rate but decreases as the reaction temperature is increased in the range 30–70°C. The general conclusion drawn from this work is that these radiation-induced emulsion polymerizations differ little from conventionally initiated systems insofar as the reaction kinetics are concerned. Poly(butyl acrylate-g-methyl methacrylate) copolymers have been prepared by a direct irradiation method involving a poly(butyl acrylate) prepolymer seed latex. Some physical properties of this material have been examined.     

Rheological characterization of the dilatant flow behavior of highly substituted hydroxypropylmethyl- cellulose solutions in the presence of sodium lauryl sulfate

 The flow behavior of aqueous solutions of three highly substituted, hydrophobic hydroxypropylmethylcelluloses (HPMC) in mixtures containing the anionic surfactant sodium lauryl sulfate (SLS) was investigated both rheo-mechanically and rheo-optically. For the first time it was possible to demonstrate dilatant flow in these systems, a phenomenon which is otherwise only known of some suspensions and associative thickening solutions. Without addition of SLS, the aqueous HPMC solutions showed the predicted flow behavior of polymer solutions, and the Cox–Merz rule was fulfilled. With the addition of SLS to these HPMC solutions, the least hydrophobic HPMC displayed no dilatancy. The solutions of a more hydrophobic HPMC with SLS exhibited on the one hand an increase in viscosity, and on the other hand shear thinning as well as shear thickening. The most hydrophobic HPMC displayed more clearly the effects of an SLS-dependent viscosity increase and the appearance of dilatant flow. At constant HPMC concentration (0.5% w/w), a maximum increase in viscosity (factor 15) was observed in the critical micelle concentration range for SLS. By rheo-optical measurements it was possible to detect an unusually pronounced alignment of the polymer segments as well as a sharp increase in the birefringence values, even before the macroscopic occurrence of dilatant flow. According to the existing network theories, this behavior of the aqueous solutions of highly substituted HPMCs in mixture with SLS has been interpreted as a shear-induced transition from intra-molecular to intermolecular interactions. Received: 4 February 1998 Accepted: 13 March 1998     

A competitive particle nucleation mechanism in the polymerization of homogenized styrene emulsions

The effects of concentrations of surfactant (sodium lauryl sulfate [SLS]) and initiator (sodium persulfate [SPS]) on the polymerization of homogenized styrene emulsions, stabilized by SLS/lauryl methacrylate (LMA) or SLS/stearyl methacrylate (SMA), were studied. The rate of polymerization increases with increasing [SLS] or [SPS]. In addition to monomer droplet nucleation, the formation of particle nuclei in the aqueous phase (homogeneous nucleation) plays a crucial role in the polymerization kinetics. In comparison with the LMA containing polymerization system, monomer droplet nucleation becomes more important when the more hydrophobic SMA was used as the costabilizer. Furthermore, the degree of homogeneous nucleation increases with increasing [SPS].     

Preparation of polypropylene microspheres for selective laser sintering via thermal‐induced phase separation: Roles of liquid–liquid phase separation and crystallization

Although selective laser sintering (SLS) has been widely applied in many fields, more research work is needed to develop proper polymer microspheres for SLS. Thermal‐induced phase separation (TIPS) is a facile way but rarely reported to prepare the polymer microspheres. The roles of liquid–liquid phase separation (LLPS) and crystallization in the TIPS process are not clear. In this study, proper polypropylene (PP) microspheres for SLS are successfully prepared via TIPS with xylene. The diameters and morphologies of these PP microspheres can be regulated easily by changing the PP concentration and the quench temperature. The large undercooling drives the solution into the metastable LLPS region and produces PP microspheres with smooth surfaces. The PP crystallization occurs both on the LLPS interface and inside the polymer‐rich phase when the solution is quenched to a temperature near the binodal line, and the tiny bent lamellae are formed on the microsphere surface. At higher temperature only PP crystallization occurs, which results in the formation of PP particles consisting of packed lamellae. The PP microspheres prepared here are suitable for SLS and promote the development of SLS potentially. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 320–329     

Kinetic studies on the oxidation of aryl methyl sulfides and sulfoxides by dimethyldioxirane; absolute rate constants and activation parameters for 4-nitrophenyl methyl sulfide and sulfoxide

The oxidations of methyl 4-nitrophenyl sulfide and sulfoxide by dimethyldioxirane, in acetone and mixtures of acetone with water, methanol, acetonitrile and hexane, have been followed by UV-Vis spectroscopy to monitor the decay of the substrates. The data show that, under all the conditions studied, both oxidations obey second-order kinetics. Grunwald-Winstein and Kamlet-Taft analyses of the influence of solvents on the second-order rate constants have been used to obtain mechanistic information on the two reactions. Activation parameters for the two oxidations in acetone and aqueous acetone have been calculated from rate constants for reactions in the temperature range 283-313 K and compared with those from sulfide and sulfoxide oxidations with other oxidants. For sulfoxide oxidations in acetone and 1-20% v/v water in acetone, the results support a concerted nucleophilic displacement by sulfur of oxygen from dimethyldioxirane with the rate being dependent on the solvent's polarity. Sulfide oxidations in acetone and 1-5% v/v water in acetone also proceed by a concerted mechanism. However, in the most polar solvent system studied, 20% v/v water in acetone, the mechanism changes in favour of a two-step reaction involving a betaine intermediate. Importantly, the sulfide oxidation shows a different solvent dependence to that of the sulfoxide, with the rate of oxidation being determined by the hydrogen bond donor capacity and electron-pair donicity of the solvent.     

Studies on the molecular interaction of safranin-T with surfactants

The spectrophotometric studies of safranin-T (Saf-T) dye in an aqueous solution containing three different types of surfactants such as CTAB (cationic), SLS (anionic) and Triton X-100 (TX-100), Tween-20, 40, 60 and 80 (nonionic) show that Saf-T forms a 1:1 molecular complex with TX-100, Tweens and SLS. Such a type of interaction is absent in Saf-T and CTAB. The thermodynamic and spectrophotometric properties of these complexes suggest that Saf-T forms a strong charge transfer (CT) complex with TX-100 and Tweens, whereas the interaction of Saf-T with SLS is coulombic in nature. Photogalvanic and photoconductometric studies also support the above interactions. In addition to this, the electron-donating ability among the nonionic surfactants i.e. TX-100 and Tweens towards dye, role of surface in CT interaction, the site of CT interaction and the intensity and stability of CT interaction between Saf-T and nonionic surfactants have been pointed out.     

Thermodynamics of formation of host-guest supramolecular polymers

The interactions between three beta-cyclodextrin hosts (having 1-3 binding sites) and two adamantyl guests (having 1-2 binding sites) have been studied by ITC, ROESY, static and dynamic light scattering (SLS and DLS), and AFM and TEM techniques. The enthalpy and free energy values (determined from ITC experiments) evidence that the single interaction between one binding site of the guest and one binding site of the host is independent of the number of binding sites of the interacting species. The average values are deltaH degrees = -26.6 +/- 2.3 kJ mol(-1) and deltaG degrees = -30.4 +/- 3.2 kJ mol(-1), indicating that the process is mainly enthalpy driven. In all cases, the experimental molar ratio (from ITC experiments) agrees with the expected one from the number of binding sites of both the host and guest. The formation of polymer-like entities was demonstrated by SLS, DLS, AFM, and TEM measurements. The structure of polymers is linear when both the host and the guest are ditopic entities and dendritic (or Cayley tree type) when the host and the guest have three and two binding sites, respectively.     

Destruction of sodium lauryl sulfate in its aqueous solutions by contact glow discharge treatment

Degradation of the anionic surfactant sodium lauryl sulfate (C₁₂H₂₅SO₄Na, SLS) in its aqueous solutions with concentrations of 0.02–1.1 mmol/L acting as a liquid cathode of atmospheric-pressure dc discharge in air at a discharge current ranging within 20–100 mA has been studied. The products of degradation in the liquid phase have been identified, and the kinetic characteristics of their formation at an initial SLS concentration of 5 × 10^?3 g/L (～0.02 mmol/L) and a discharge current of 40 mA have been determined.     

Particle size analyses of porous silica and hybrid silica chromatographic support particles. Comparison of flow/hyperlayer field-flow fractionation with scanning electron microscopy, electrical sensing zone, and static light scattering

Porous silica and hybrid silica chromatographic support particles having particle diameters ranging approximately from 1 microm to 15 microm have been characterized by flow/hyperlayer field-flow fractionation (FFF). The particle size accuracy has been improved significantly in this work by a second-order polynomial calibration. Very good agreement between the FFF data and scanning electron microscopic (SEM) results has been achieved. The effects of particle porosity, pore sizes, and particle sizes on the particle size accuracy in electrical sensing zone (ESZ) analyses have been discussed. It has been demonstrated by computer simulation and experimental measurements that false peaks can be generated in certain particle size regions when the static light scattering (SLS) technique is applied to tightly distributed spherical chromatographic support particles.     

Micellar catalysis in the oxidation of acetophenones by Ce(IV)

Rate of oxidation of acetophenones by Ce(IV) in aqueous acetic acid 80:20 (v/v) either slows down or remains constant over a range of cetyltrimethyl ammonium bromide (CTAB) concentration exceeding the cmc value. The rate is then found to increase sharply as the surfactant concentration increases with no sign of reaching a maximum or constant value. From Fluorescence quenching, binding constant for p-nitro acetophenone has been evaluated. The rate data have been rationalized on the basis of a reaction between the acetophenones situated on the micelle surface and active Ce(IV) species in the bulk aqueous phase.     

Effects of hydrophilic chain length on the characteristics of the micelles of pentaoxyethylene n-decyl C10E5 and hexaoxyethylene n-decyl C10E6 ethers

Wormlike micelles of nonionic surfactants pentaoxyethylene decyl ether C(10)E(5) and hexaoxyethylene decyl ether C(10)E(6) in dilute aqueous solutions were characterized by static (SLS) and dynamic light scattering (DLS) experiments at several temperatures T below the critical points. The SLS results were analyzed with the aid of the molecular thermodynamic theory for SLS from micelle solutions formulated with the wormlike spherocylinder model, thereby yielding the molar mass M(w) of the micelles as a function of c and the cross-sectional diameter d of 2.6 nm for both C(10)E(5) and C(10)E(6) micelles. It has been found that the micelles grow in size with increasing c and T, following the relation M(w) proportional, variant c(1/2) in conformity with the theoretical prediction for highly extended polymerlike micelles. The hydrodynamic radius R(H) of the micelles as a function of M(w) was found to be also well described by the corresponding theories for the wormlike spherocylinder model. The results of the stiffness parameter lambda(-1) show that both micelles are rather stiff compared with those formed with other polyoxyethylene alkyl ethers C(i)E(j) but far from rigid rods. The values of the spacing s between two adjacent hexaoxyethylene chains on the micellar surface were found to be substantially the same for both micelles.     

Emulsion polymerization. II. Review of experimental data in the context of the revised Smith-Ewart theory

Tables are presented for convenient calculation of the basic parameters of the revised Smith-Ewart theory. For the methyl methacrylate (MMA)/sodium lauryl sulfate (SLS)/K₂S₂O₈, and for the styrene/SLS/K₂S₂O₈ reaction mixtures parameters are presented from which the absolute values of the following quantities can be conveniently calculated for any temperature, soap, and initiator concentration: particle number, particle radius, conversion where particle nucleation stops, rate and molecular weight in interval II, the interval after completion of particle nucleation and before the disappearance of monomer droplets. The theoretical predictions are compared to new experimental data and to those from the literature. The available data confirm the theoretical prediction that particle nucleation stops after a very small amount of polymer is formed, of the order of 0.01 cc. polymer/cc. water in most recipes. The theory and experiments are in good qualitative agreement for the conversion rate prior to completion of particle formation: the conversion rate rises with time and, when particle nucleation stops, it levels off. Excellent quantitative agreement can be obtained between theoretical and experimental particle size values. In the experiments of this laboratory the SLS concentration was varied 60-fold, the K₂S₂O₈ concentration was varied 140-fold and the difference between theoretical and experimental poly(MMA) particle radii was always less than about 20%. Similar good agreement was obtained for polystyrene over the temperature range 30–90°C. Some polystyrene data from the literature with carboxylic soaps give just as good fit as the data with SLS of this laboratory. The predicted proportionality between particle number and the product of 0.6 power of soap concentration and of 0.4 power of initiator concentration was observed for several monomers. The theoretical predictions for the rate and molecular weight obtained in interval II are valid only for relatively low initiator and high soap recipes. For recipes for MMA and styrene the rate data are in good agreement with those calculated from the theory. The theory also correctly predicts the order of magnitude of the experimental molecular weights. For several monomers the rate and molecular weight vary with initiator and soap concentrations in a manner close to theoretical predictions.     

Investigation of solvolysis kinetics of new synthesized fluocinolone acetonide C-21 esters--an in vitro model for prodrug activation

In this study the solvolysis of newly synthesized fluocinolone acetonide C-21 esters was analysed in comparison with fluocinonide during a 24-hour period of time. The solvolysis was performed in an ethanol-water (90:10 v/v) mixture using the excess of NaHCO?. The solvolytic mixtures of each investigated ester have been assayed by a RP-HPLC method using isocratic elution with methanol-water (75:25 v/v); flow rate 1 mL/min; detection at 238 nm; temperature 25 °C. Solvolytic rate constants were calculated from the obtained data. Geometry optimizations and charges calculations were carried out by Gaussian W03 software. A good correlation (R = 0.9924) was obtained between solvolytic rate constants and the polarity of the C-O2 bond of those esters. The established relation between solvolytic rate constant (K) and lipophilicity (cLogP) with experimental anti-inflammatory activity could be indicative for topical corticosteroid prodrug activation.     

Structure and dynamics of solutions of a polystyrene–polybutadiene pentablock copolymer in a styrene‐selective solvent

We have examined solutions of a polystyrene–polybutadiene pentablock copolymer in 1,4‐dioxane, a slightly selective solvent for polystyrene and a θ solvent for polybutadiene, with static light scattering (SLS), dynamic light scattering (DLS), and small‐angle neutron scattering (SANS). The SANS data have been analyzed with the Percus–Yevick model to represent the scattering from interacting cores, approximated as hard spheres, and with a Lorentzian function to represent the scattering from unassociated and associated polymer chains. The SANS data at 25 °C clearly reveal interacting domains, approximately 6 nm in radius, formed by the association of the insoluble polybutadiene block in the 20% sample. The 4% sample does not show such domains, whereas the 7% sample represents an intermediate situation, with both unassociated polymer and associated polymer. At higher temperatures, the domains dissolve. The DLS data for samples with concentrations of 2–22% show two diffusive modes: a fast mode corresponding to the cooperative dynamics of concentration fluctuations and a slow mode corresponding to the diffusion of clusters. The large length‐scale heterogeneities, indicated by the strong angular dependence of SLS, implies that the small microdomains of about 10–15 polybutadiene blocks are bridged by the polystyrene chains, forming large aggregates with randomly distributed crosslinks on length scales much larger than the domain size. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2807–2816, 2002