Laser properties of YAG: Nd,Ti

YAG: Nd containing 10^–3 wt% Ti showed slightly increased losses at 1·064 m but a substantially increased gain coefficient if compared with a material containing no Ti. The increased losses may be attributed to the increased absorption near 1·064 nm and the increased gain to the better energy coupling among Nd³⁺ ions occupying nonequivalent sites due to the presence of Ti³⁺ ions. YAG: Nd, Ti may be used as a high performance pulsed laser.     

Luminescence sensitization in Nd-Cr-Ce doped yttrium aluminates

Energy transfer from Ce to Cr in YAG is radiative and relatively inefficient. If excited below 500 nm, the opposite transfer is dominant. YAP: Ce, Cr showed relatively efficient CeCr transfer only. The sensitization of Nd³⁺ luminescence by Ce³⁺ ions depends on the overlap of the Ce³⁺ emission band with Nd³⁺ absorption lines. Cr³⁺Nd³⁺ transfer is characterized by an expressive non-radiative portion. It is inefficient in YAG but very efficient in YAP. No UV-induced colour centres were found in YAG: Nd, Cr grown under Ar-H₂ atmosphere and doped with 10^–3 wt. % Cr, but at a higher Cr concentration anomalous absorption between UV absorption edge and 650 nm was stabilized. Ce³⁺ admixture in YAG:Nd, Cr and/or reducing treatment of the crystals facilitate the decomposition of the centres. The decomposition is accompanied with a strong Nd³⁺ luminescence. Therefore, YAG: Nd, Ce, Cr is an advisable active laser material. On the other hand the same centre in YAP: Nd, Cr seemed to be more stable even in the presence of cerium ions.     

Transient absorption and laser output of YAG : Nd

YAG : Nd grown under 98% Ar 2% H₂ protective atmosphere free of nitrogen or hydrocarbons showed after UV irradiation broad absorption peaked at 1·9×10⁴ cm^–1 which disappeared relatively slowly at room temperature. It was more intensive in oxygen treated samples than in those annealed in hydrogsn. Transient absorption suppresses laser output by the increase of absorption at 0·94×10⁴ cm^–1 (1064 nm) and, particularly in CW mode, by the anomalous rod deformation. YAG : Nd containing Fe ions (2·10^–4 wt%) showed no transient absorption.     

CW diode pumping and FM mode locking of a Nd: KGW laser

We have demonstrated cw diode end pumping of Nd: KGW, a novel solid-state gain medium, with up to 30% conversion efficiency into near-TEM₀₀ (M² < 1.05) output at = 1.067 µm for a pump level of 2.7 W. The slope efficiency was limited by intracavity reflections to 36%; however, direct comparison to a similar Nd:YAG laser indicates the same intrinsic slope efficiency of 60%. FM mode locking of this laser at 200 MHz has produced 12 ps pulses (compared to 16 ps for Nd: YAG), although an intracavity etalon was required. Considerable reduction in pulse width is possible (the line width limit is 0.5 ps) but different techniques may be necessary. Spatial hole burning was evident in both the 120 GHz free-running spectrum and the etalon-limited mode-locked spectrum.     

Cr:Tm:Ho:YAG (2.1 μm) and Nd:YAG (1.444 μm) pulsed-laser lithotripsy of bile duct stones

The Nd:YAG (1.444 m) and Cr:Tm:Ho:YAG (2.1 m) free-running laser systems of the output energy of 300 mJ per pulse and repetition rate 1 Hz have been developed and used for bile duct stones fragmentation study in vitro. A total of 67 human bile duct stones of known sizes, collected from surgical sources were used in the experiments. Insensitivity of the stones fragmentation to the type of the laser used, and insensitivity of the fragmentation efficiency to the type of stone, was observed. No pathological changes of the tissue were observed for non-human soft tissue laser irradiation (in vitro) by 1, 2, and 5 pulses of the Cr:Th:Ho:YAG radiation of the fluency of 1.6 J/cm². The lasers are found to be good candidates for laser lithotripsy.     

Spectroscopic, Phototropic, and Lasing Properties of Cd1−x Mn x Te Single Crystals Doped With Chromium Ions

The spectroscopic properties of Cr²⁺ ions in Cr:Cd_1–x Mn _x Te (CMT) crystals are studied, and the possibility of using these impurity crystals as active media and saturable absorbers of solidstate lasers of medium IR range is demonstrated. The bands of absorption with a maximum at 1.9 m and of luminescence with a maximum at 2.6 m correspond to the transitions between the levels ⁵ T ₂ and ⁵ E of the tetracoordinated Cr²⁺ ions with more than 1·10^–18cm² cross sections. The pulsed and continuous lasing modes of a Cr:CMT laser are realized in the 2.6m region. The Cr:CMT crystals are characterized by effective saturation of impurity absorption. The cross sections of absorption from the ground and excited states of the Cr²⁺ ions at = 2.09 m are determined: _gsa = 1.1·10^–18 cm²; _esa/_gsa < 0.1. With the use of the Cr:CMT crystals as a passive gate the regime of Qswitching of the Cr,Tm,Ho:YAG laser emitting at = 2.09 m is obtained.     

Near-Field Diffractive Optical Pumping of a Laser Medium

A Nd:YAG rod active element placed inside a resonator was pumped by the second harmonic radiation (the wavelength =0.532 m) of a Q-switched Nd:YAG laser diffracted at a circular aperture. Various distributions of pumping intensity in the Fresnel (near-field) region along the direction of the pump beam diffraction were produced. Inversion profiles with maxima or minima at the resonator axis were formed in the active element, depending on its distance from the circular aperture. Gain-switched operation of the Nd:YAG rod laser at =1.064 m is reported at the fundamental mode and also at the TEM₀₁, TEM_01* and other higher-order modes for different positions of the active element in the near-field region. Applications of such diffractive optical pumping for the concentration of the pumping radiation into the active media and for laser beam profling are discussed. © 2004 The Optical Society of Japan     

A sensitive non-destructive method for measuring the Nd doping concentration in Nd : YAG with high spatial resolution

This paper reports on an experimental method for measuring in Nd:YAG the Nd doping concentration (C) with high sensitivity (0.01 at.%Nd) and high spatial resolution (50 m). The method is based on the measurement of the fluorescence lifetime _f of the upper Nd laser level. Additional parameters required to determine C are the intrinsic fluorescence lifetime ₀ and the quenching parameter Q. The measured values of _f, ₀ (256.47±0.14 s) and Q (4.45±0.40×10²⁰ cm^-3) allow us to calculate the Nd concentration C with an absolute accuracy of 0.1 at.%Nd. By using this method C is measured at the outer surfaces of standard laser rods and at the faces of boule slices (with diameters of up to 50 mm). The obtained results demonstrate a detection sensitivity of 0.01 at.%Nd. PACS 42.70.Hj; 81.70.Fy     

Corrigendum: ‘Output power limitations in CW single transverse mode Nd:YAG lasers with a rod of large cross-section’

Corrigendum: Output power limitations in CW single transverse mode Nd:YAG lasers with a rod of large cross-section     

Mode-locking of neodymium lasers by glasses doped with PbS nanocrystals

Nonlinear optical absorption properties of silicate glasses doped by the PbS nanocrystals were investigated by means of the picosecond pump-probe absorption spectroscopy and absorption bleaching technique. The glass samples were used as saturable absorbers for passive mode-locking of Nd:YAG and Nd:glass lasers. Application of the PbS doped glass together with the active mode-locking and laser cavity quality control enabled the stable of generation of 28 ps and 5 ps duration pulses in Nd:YAG and Nd:glass lasers respectively. PACS 42.60.Fc; 42.70.Hj; 78.47.+p     

Growth and magnetism of Fe on Cr(001): a spin-polarized scanning tunneling spectroscopy and magnetic force microscopy study

The growth and magnetic domain structure of Fe nanoislands and films on Cr(001) are investigated by spin-polarized scanning tunneling microscopy and magnetic force microscopy (MFM). Topographic images of films grown at different substrate temperatures reveal that the highest film quality is obtained by evaporation at room temperature and subsequent annealing at 500 K for 4 min. Spin-resolved studies of the magnetic structure of submonolayer Fe films (coverage 0.2 ML) show the expected antiferromagnetic Fe–Cr coupling, i.e. any Fe island is magnetized antiparallel with respect to the underlying Cr(001) terrace. As the Fe coverage exceeds 0.2 ML the magnetic contrast decreases and completely vanishes for 0.4 ML. Only for 3 ML does a weak magnetic contrast reappear, which is interpreted in terms of a small spatial variation of the 90° coupling between the Cr substrate and the Fe overlayer. MFM reveals that the number of visible domain walls decreases with increasing film thickness and completely vanishes at 12 ML. PACS 68.55.-a; 75.60.Ch; 68.37.Ef     

The Q-switched Nd : YAG and Yb : YAG microchip lasers optimization and comparative analysis

The microchip lasers based on the neodymium or the ytterbium doped yttrium-aluminium garnet crystal and Q-sw itched by the Cr⁴⁺:YAG film are considered. The optimal (maximizing of energy) values of the pumping beam radius, the absorber parameters (the thickness and tetravalent chromium ion concentration), and the output mirror reflectivity are determined. The possibility of higher values of energy in the Yb:YAG laser pulse, in comparison with a more traditional Nd:YAG laser, is also substantiated. PACS 42.60.Gd     

Spectral response of CdS with Ag,Cu, and in impurities

High-resistance (dark 10⁸ · cm) photosensitive CdS samples (light 10²–10³ · cm at saturation) were obtained from low-resistance ( 0.1 · cm) nonphotosensitive CdS single crystals by thermal diffusion of Cu, Ag, and In in vacuum at 2 · 10^–5 torr. The spectral response of impurity and pure high-resistance photosensitive single-crystal CdS samples was studied in the wavelength range from 0.35 to 3. The short-wave and long-wave limits of the spectral curves, the wavelength range of maximum photoconductivity and the forbidden band width, the depth of impurity levels, the upper edge of the impurity band, and the depth of maximum-density activation centers have been determined from the spectral curves. The results are discussed and compared with published data.Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 6, pp. 117–121, June, 1972.     

Pulsed laser crystallization of hydrogen-free a-Si thin films for high-mobility poly-Si TFT fabrication

The possibility to fabricate high-mobility polysilicon TFTs by nanosecond pulsed laser crystallization of unhydrogenated amorphous Si thin films has been investigated. Two types of lasers have been used: a large area ( 1 cm²) single ArF excimer laser pulse and a small diameter ( 100 m) frequency-doubled Nd:YAG laser beam, working in the scanning regime. Processed films have been characterized in detail by different optical and microscopic techniques. Device performances indicate that the best results are achieved with the excimer laser leading to high mobility values (up to 140 cm²/Vs) which are much larger than in polysilicon TFTs fabricated onto the same quartz substrates by low-temperature thermal (630° C) crystallization of amorphous Si films (_fe55 cm²/Vs).     

Additive pulse mode-locked Nd: YAG laser

Additive pulse mode locking applied to lamppumped Nd: YAG lasers results in an attractive source of picosecond pulses at 1.06 m or 1.32 m with average powers at the Watt level. We provide detailed information on construction and operation and give data on performance. A modified active stabilization scheme allows not only improved stability of operation but also insight into the dynamics of pulse formation.     

Near Field Observation of a Refractive Index Grating and a Topographical Grating by an Optically-Trapped Gold Particle

We observed the near field for a refractive index grating fabricated on a planar light waveguide circuit (PLC) by scanning an optically-trapped 100 nm diameter gold particle. We demonstrate that stable trapping and scanning occur with a Gaussian laser beam at the scan velocity of 1.6 m/s and Nd:YAG laser power of 25mW. The scattered Ar laser light from the gold particle is strong at high refractive indexes of the grating with periods of 1.06 m and 0.53 m both by s and p polarized illumination. In addition, we observed the surface profile of the optical disk tracking groove with and without the gold particle. © 2004 The Optical Society of Japan     

Mechanism transition of self-pumped phase conjugation in KTa1 −xNbxO3:Fe crystals

Mechanism transitions of Self-Pumped Phase Conjugation (SPPC) with wavelength and doping concentration are observed in KTN:Fe (KTa_{1 –x} Nb _x O₃:Fe with _x = 0.48) crystals. The SPPC mechanism in KTN: Fe (0.4 wt. %) crystal transforms from Stimulated Photorefractive Backscattering and Four-Wave Mixing (SPB-FWM) to cat (or total internal reflection) as the wavelength increases from 514.5 nm to 620 nm. SPPC at 514.5 nm is formed with the cat mechanism in a 0.2 wt. % doped KTN:Fe crystal, while with the SPB-FWM mechanism in a 0.4 wt. % doped one. These mechanism transitions are discussed with respect to the dependence of the backscattering gain coefficient of the crystals on wavelength and doping concentration.     

Width reduction of laser microdrillings by subsequent mechanically induced plastic deformation

This work reports a novel process combination, which is capable of forming large hole matrices (100 pores/mm²) in thin stainless steel foils (10 mfoil<300 m) maintaining high processing rates and pore widths smaller than 5 m. This technique perforates stainless steel foils with high-speed on-the-fly laser perforation (60000 drillings/min) followed by a cold-roll forming of the laser-treated foil. The cold-roll forming leads to a pore-size reduction (in one dimension) perpendicular to the rolling direction. For the laser processing a diode-pumped, q-switched and frequency-tripled Nd:YAG laser (=355 nm, =30 ns), and a flashlamp-pumped Nd:YAG laser (=1064 nm, =57 s) were applied. Using this process combination, minimum pore sizes of 3.5 m have been achieved. At present, the processing efficiency of cold-rolled percussion drillings inserted with nanosecond pulse durations is lower in comparison with single-pulse on-the-fly perforation, but in terms of quality (straight pore channel, low standard deviation of pore widths and pore widths smaller than 5 m) well suited for various fields in filtration (e.g. particle removal) . PACS  81.20.Hy; 42.62.Cf; 81.40.Ef     

Structure formation on titanium during oxidation induced by cumulative pulsed Nd:YAG laser irradiation

We investigated local oxidation and surface structure development of Ti targets under multi-pulse, high-repetition-rate Nd:YAG ( =1.064 m, 300 ns, =30 kHz) laser irradiation in air at atmospheric pressure. The experiments were performed at laser intensity levels below the single-laser-pulse melting threshold of Ti. The morphology of the irradiated areas was studied by scanning electron microscopy and profilometry. The variation of the oxide compositions and the crystalline state with increasing laser pulse number was analysed by X-ray diffractometry. Besides the known phenomena related to laser irradiation and oxidation of metal surfaces (micro-crack or pore formation), we evidenced new morphological features such as droplet-like structures inside the surface micro-cracks and micro-columns, and with increasing laser pulse number the formation of a dome-shaped structure over the whole irradiated zone. The occurrence of melting under multi-pulse irradiation was associated with the rise in the surface temperature enhanced by the oxidation, and the progressive evolution of the surface structures was associated with the consecutive melting–solidification processes as well as with the different stages of oxidation. PACS 61.80.Ba; 68.37.Hk; 81.65.Mq     

Two independently tunable distributed feedback dye lasers pumped by a single picosecond Nd : YAG laser

A laser system which consists of two independently tunable Distributed Feedback Dye Lasers (DFDL) pumped by 35 ps pulses at the second and third harmonics of a Nd : YAG laser is presented. The DFDLs employ a new grating-prism configuration for producing the gain grating in the laser dye solution. Thus easy switching of the pump wavelength is possible. Details of construction and characteristics of operation are reported. Examples of continuous computer controlled tuning from 400 to 750 nm are shown. The pulse durations, which are of the order of 12 ps, are discussed by comparison with experimental and theoretical data from the literature.Prof. F.P. Schäfer on the occasion of his 65th birthday.