Stress effect on the magnetoresistance of amorphous ferromagnets

To investigate the magnetization in amorphous ferromagnetic alloys we measured the change in the magnetoresistance (H⊥j and H 6j) simultaneously applying a tensile stress along the direction of the ribbons. With increasing stress we observed a complete alignment of the magnetic domain vectors M_s parallel andantiparallel (for λ_s > 0) or perpendicular (for λ_s < 0) to the stress axis. It is found that on average a value of σ_s = 10 kg/mm² is sufficient in all measured samples to produce this effect. The change in the magnetoresistance by stress annealing indicates that a preferred domain orientation in stress direction is induced.     

Influence of Stress Dependence of Lubricant Shear Modulus on Self-Similar Behavior of Stress Time Series

Here we consider melting of an ultrathin lubricant layer between two atomically smooth solid surfaces taking into account the stress dependence of the lubricant shear modulus and its decrease with increasing stress (strain). In the adiabatic approximation with the stress relaxation time far longer than strain and temperature relaxation times, a Langevin equation is written and its respective Fokker-Planck equation is derived using the Stratonovich calculus. Phase diagrams for the steady case are presented illustrating the effect of the system parameters on the lubricant behavior. A joint numerical and analytical analysis demonstrates a very close match between probability distributions at different parameters. It is shown that in a limited stress range, a self-similar mode of dry friction is established showing up in self-similar behavior of stress time series.     

Stress relaxation in the earth and seismic activity

Consideration of the models described in the preceding pages shows that a sound theoretical basis exists for a physical understanding of post-seismic ground deformations and several other phenomena associated with the asthenosphere relaxation. Since the asthenosphere seems to be involved in a direct way in the seismic mechanism, the knowledge of its rheological properties becomes an essential point to understand the seismic mechanism too. Once a reasonable knowledge of the asthenosphere behaviour is achieved, the models can tell us how the system lithosphere-asthenosphere will evolve after an earthquake or a similar perturbation of the stress field. It will be necessary to compute the stress pattern not only at the Earth surface, but also at the depth where the faults lay. By knowing how stress changes in space and time through the lithosphere, one might predict, for instance, the arrival of a stress wave on a seismogenetic structure: this wave might trigger an earthquake in this zone, if favourable conditions are found.     

应用干涉原理检测激光晶体夹具的应力

详细介绍了激光干涉原理,在此基础上,引入了一种简单实用的板条激光器夹具应力检测方法,从而减小了应力对板条激光器带来的不利影响。实验结果表明：夹具对板条各个方向产生的应力均匀,通过初步实验得到了6.94 W的1 064 nm连续光输出。     

Active Control of Cellular Orientation through In-Situ Stress in the Substrate

We investigate the orientation of cells on substrates to find possible methods for controlling the cellular orientation. The force dipole model is employed in our modelling and simulation. The elastic interaction between cells as well as the elastic interaction between the cell and in-situ stress field in the substrate are found to be the two main physical mechanisms to control the cellular orientation. The former interaction dominates the cellular orientation when the in-situ stress is small, while the later dominates when the in-situ stress is large enough. Two cells tend to align perpendicularly on a free substrate, but the cellular orientation varies with the increasing in-situ stress. Two cells tendto align in parallel when the normal stress is large enough. Their direction is perpendicular to the extension stress direction or parallel to the compression stress direction. When the positive in-situ shear stress is large enough, the two cells tend to align at -45°. Based on this theoretical simulation, it is believed that the cellular orientation on substrates can be controlled by thein-situ stresses.     

Influence of Fibre Taper on the Interfacial Shear Stress in Fibre-Reinforced Composite Materials during Elastic Stress Transfer

The paper is concerned with finite element (FE) analysis of stress transfer from an elastic matrix to an elastic fibre, which need not be a uniform cylinder, in a fibre-reinforced composite material. Axisymmetric models of fibres embedded in co-axial cylindrical matrices were investigated by the FE method. Fibre shapes investigated were cylindrical, ellipsoidal, paraboloidal taper and conical taper. The effects of varying the fibre aspect ratio, q (ranging 200 to 3500) and Young's modulus (relative to that of the matrix), E _f /E _m (ranging 10³ to 10⁶) were investigated. The results show that ellipsoidal and parabolic tapers lead to a similar distribution of interfacial shear stress (τ) to that observed for a uniform cylindrical fibre, except that the magnitude of the stress is higher. For a conical taper (except for q = 200, E _f /E _m = 10⁶), the interfacial stress increases to a maximum between the centre and the end of the fibre and then decreases towards the fibre ends. The effect of fibre taper on the distribution of τvalues is reflected in the axial tensile stress, σ_z , distribution induced in a fibre. For example, for a fibre with a conical taper, the distribution of τ values can lead to an even distribution of σ_z along the length of a fibre.     

Stress distributions in diblock copolymers

We demonstrate how a generalized self-consistent field theory for polymer melts that includes elastic stress and strain fields can be applied to the study of AB diblock copolymers melts. By obtaining the stress distributions for volume conserving strain loadings where lamellar and hexagonal morphologies are stable, we show that the local stress is reduced at the domain interface but slightly enhanced in the immediate vicinity of the interface. The overall stress profile is the result of the combined effects of chain connectivity across the interface, which yields a positive contribution, and the immiscible nature of the monomers, which leads to a stress reduction because of interfacial tension.     

CR超导二极磁铁线圈受力分析

采用有限元分析的方法, 以CR超导二极铁为研究对象, 对其进行受力分析, 分别计算线圈所受到的电磁力以及在此力作用下线圈发生的应变, 线圈和相邻部分降温速率不均匀引起的热应力的分布以及线圈发生的应变. 最后利用所得到的数据来校对线圈和线圈盒的强度, 为结构的优化设计提供依据, 并为失超保护提供可参考的数据.     

圆芯边孔光纤的应力区和双折射

报道了圆芯边孔光纤(CSF)中应力分布和双折射的研究结果。用有限元法建立了求解圆芯边孔光纤横截面应力和双折射的计算模型,分析了圆芯边孔光纤横截面应力和应力双折射的分布形态,给出了详尽的物理解释。计算结果表明圆芯边孔光纤的横截面上出现应力分量的拉应力区和压应力区,应力区在纤芯附近对称分布,且不同应力区中应力双折射取向不同。应力分量和应力双折射在圆芯边孔光纤横截面上积分为零。圆芯边孔光纤的几何双折射随波长增加而增大,短波长处几何双折射为零,模式双折射等于应力双折射,随着波长增加,模式双折射逐渐偏离纤芯中心处应力双折射而靠近几何双折射,到长波长处模式双折射主要是几何双折射。对于不同材料组成和结构尺寸的圆芯边孔光纤,模式双折射的数值在10-5量级,随波长增加模式双折射先减小后增加。     

单轴应力对量子阱红外探测器吸收波长的影响

以单轴应力作用下超晶格量子阱应变能带理论为基础,采用电子反射与干涉方法,研究了单轴应力对超晶格能带的影响,推导了单轴应力与超晶格导带子能级的定量关系。以GaAs-AlGaAs-GaAs为例,具体计算了导带中子能级对应力的依赖关系,进而给出了单轴应力对n型AlGaAs-GaAs量子阱红外探测器(QWIP)吸收波长的影响。计算结果表明,随着单轴压应力的增大,量子阱红外探测器的吸收波长表现出较明显的变化。当单轴压力增大到1.3GPa,量子阱红外探测器的吸收峰值移动了将近1.1μm,并且基本与应力呈线性关系。量子阱红外探测器吸收波长连续可调范围5.57～4.46μm。     

EAST超导托卡马克装置主机支撑结构极低温条件下应力应变分析

报道了国家"九五"重大科学工程EAST超导托卡马克核聚变实验装置中心液氦冷却冷质部件的钢/高分子复合材料支撑装置在模拟冷却收缩条件下的应力应变分析结果。单个支撑结构由高分子复合材料桶状结构固定在垂直薄板板簧结构上部组成。实验表明该支撑装置在顶部水平负荷作用下发生S型扭曲,而不是简单的悬臂梁式形变。支撑部件整体在试验范围内,在常温、低温条件下均对外加顶部水平推力呈线弹性形变。但在低温下,环氧树脂部件与不锈钢板簧结合部的应变,随外力呈非线性弹性形变,这与室温下的线性变化成鲜明对照。低温下整个部件刚性增加,与常温比较,同等水平位移需要的外力增加,但是环氧树脂部件上的应力反而较常温下显著减小;不锈钢板簧底部上部与环氧部件结合部应力则显著增加。     

Stress dependence of the magnetic permeability of MnZn ferrous ferrites

In monocrystalline MnZn ferrous ferrites the magnetic permeability μ as a function of temperature T has been observed to show a striking dependence on applied stress. Stresses cause the μ(T) curve to cant around a point near its maximum arising from compensation of the magnetocrystalline anisotropy due to the ferrous ions. By grinding the surface of a monocrystalline toroid, a tensile stress was exerted on the interior of the specimen. The canting of the μ(T) curve observed when the damaged surface layer was removed step by step was employed to study the underlying physical mechanism. In the case of polycrystalline materials the maximum of μ(T) is usually strongly suppressed. Nevertheless, it proved possible to investigate the dependence of μ(T) on applied stress in a polycrystalline MnZn ferrous ferrite pot core.     

Vocal Fold Impact Stress Analysis

Vocal fold impact stress (force/area) has been implicated as a factor possibly contributing to the formation of nodules and polyps. The force of impact of a moving body is related to its acceleration. Since the mass of the folds is relatively constant, one expects impact force to be directly proportional to acceleration. A measure that reflects the relative displacement of the vocal folds is photoglottography (PGG). The velocity and acceleration of the folds are easily obtained by calculating the first and second derivatives of the PGG displacement waveform. This study, therefore, compared the second derivative of the PGG signal with simultaneously measured impact stress in an excised canine larynx model. Glottal transillumination (PGG) was measured with a subglottic transducer. A miniature force transducer placed in the midline between the vocal folds measured impact stress at the midglottal position. For nine different larynges, there was a positive and linear relationship between the second derivative of PGG and impact stress. The statistically significant results support the hypothesis that the second derivative of PGG m ay provide a use fulnoninvasive way to estimate relative vocal fold impact stress.     

Stress investigations of thin amorphous Ge-Se-Ga films

Thin chalcogenide films from the systems (GeSe₄)_1-xGa_x and (GeSe₅)_1-xGa_x with gallium contents up to 20 at. % have been prepared by vacuum evaporation and their stress has been investigated by a cantilever technique. The addition of gallium to the Ge-Se matrix plays an important role in stress formation in the films: films without gallium possess negligible stress, while all gallium-containing films are under compressive stress. The increase of the gallium content leads to structural changes and an increase in the density, which results in higher stress values. For all films, stress reduction with time is observed due to spontaneous relaxation. Received: 2 October 2002 / Accepted: 22 November 2002 / Published online: 28 March 2003 RID="*" ID="*"Corresponding author. Fax: +49-561/8044-136, E-mail: popov@schottky.physik.uni-kassel.de     

偏振相机的透明元件应力测量北大核心CSCD

应力检测对光学元件的制造和使用意义重大。基于应力双折射原理,提出了一种利用偏振相机测量应力分布的方法。根据Stokes矩阵和Mueller矩阵推导出应力值及应力方向计算公式,并对影响系统测量精度的主要误差进行了理论分析。为验证方法的可行性,搭建了一台测量应力分布的装置。使用该装置测量一块633 nm的四分之一波片,测得其误差为0.86 nm。进一步测量,得出一块车灯透镜的全场应力相位延迟量与应力方向图,利用所测相位延迟量计算出透镜中心区域的应力双折射值为9.21 nm/mm、主应力差为2.45 MPa;利用符号规则调整了透镜的应力方向,结果符合应力连续性原则。该方法测量应力分布时无需旋动光学元件,可实现应力延迟量及应力方向的实时测量。     

水胁迫下典型盐生植被梭梭光谱特征分析

荒漠地区由于气候干燥，降水稀少，水分常成为制约植被生长的因素之一，水分胁迫对植物长势和产量的影响比任何其他胁迫都要大。随着高光谱技术的发展，国内外已有众多学者利用高光谱数据研究植被遭受胁迫作用，然而这些研究对象多集中于甜菜、棉花、玉米、水稻等作物，针对干旱区盐生植被遭受胁迫作用的研究较少。梭梭作为荒漠、半荒漠地区的典型盐生植被之一，具有极高的经济和生态效益。选择梭梭作为研究对象，培育一年生梭梭，并设置三个水分梯度，形成受不同水分量胁迫的梭梭。使用原始光谱、红边位置参数，结合植被指数及二维相关光谱研究其叶片光谱特征，为干旱区利用高光谱遥感监测盐生植被提供借鉴。结果表明：(1)分析梭梭叶片反射光谱曲线发现，在可见光至中红外各波段范围内，受不同水分量胁迫作用的梭梭叶片光谱反射率有显著差异。在可见光(350～610 nm)波段，各水分处理的梭梭叶片反射率依次为100 mL>500 mL>200 mL，这是由于100和200 mL水分促进梭梭内部叶绿素合成，使该波段反射率降低，而过多的水分(500 mL)对梭梭内部的叶绿素合成没有更大的促进作用。在红光区(611～738 nm)，随着水分量的增多，受不同水分量胁迫的梭梭叶片光谱反射率依次减小。在738～1 181和1 228～1 296 nm波段，受不同水分量胁迫作用的梭梭叶片光谱反射率为：200 mL>100 mL>500 mL；在1 182～1 227 nm波段，受不同水分量胁迫作用的梭梭叶片光谱反射率为：100 mL>200 mL>500 mL。这是由于植被细胞结构对近红外区域的反射率影响较大，因而受不同水分胁迫作用的梭梭叶片光谱反射率有显著差异。在1 300～1 365和1 392～1 800 nm波段，受各水分胁迫作用的梭梭叶片反射率为：100 mL>200 mL>500 mL。这表明在500 mL水分胁迫量范围内，水分越多，叶子的细胞液、细胞膜对水分的吸收能力越强，使得反射率下降。通过对原始光谱求取一阶导数并提取红边位置参数发现，各水分处理下的梭梭叶片一阶微分光谱曲线中红边位置未发生移动。这是由于梭梭在长期的干旱环境影响下，形成了特殊的适应机制，水分对其红边位置影响不敏感。(2)选取若干植被指数分析各水分处理下的梭梭光谱指数变化。当水分胁迫量由100 mL增至200 mL时，WI/NDWI，MSI和NDII指数值变化显著，可用于研究水分胁迫下梭梭的光谱特征。(3)使用二维相关光谱技术分析受各水分胁迫作用的梭梭光谱特征，得出在100 mL水分胁迫下，在536，643，1 219和1 653 nm波段处，吸收峰对水分的微扰敏感；在200 mL水分胁迫下，在846和1 083 nm波段处，吸收峰对水分的微扰敏感；在500 mL水分胁迫下，在835和1 067 nm波段处，吸收峰对水分的微扰敏感。总之，在近红外波段，与100 mL水分量相比，梭梭受200和500 mL水分量胁迫时，吸收峰对水分的微扰敏感度上升。由100 mL水分胁迫下梭梭的二维同步相关谱图可知，1 044和1 665 nm，1 072和903 nm，903和1 264 nm，1 230和1 061 nm波段处形成正交叉峰，表明这些波段处光谱强度随水分的干扰同时变化。     

动态应力场作用下线性啁啾光栅光谱特性研究

目前柔性结构损伤检测需多个传感器,且需要探测器具有极高的采集频率。光纤光栅具有动态响应快、易实现分布式测量等特点,为解决上述问题提供了有效的途径,提出采用线性啁啾光栅(LCFBG)实现动态应力场探测。首先,用传输矩阵理论建立了LCFBG反射光谱应变传感模型,用衰减正弦函数模拟沿LCFBG分布的动态应力场。通过仿真实验,详细研究了LCFBG反射光谱对不同振幅、不同衰减系数与不同传播速度动态应力场的响应特性。实验结果表明,LCFBG反射光谱的反射率、波长变化与光谱形状均与动态应力场上述参数有关,但是LCFBG反射光谱对动态应力场不同参数的响应规律不同。在一定范围内,LCFBG反射光谱的最大反射率随动态应力场幅值与速度的增大而增大,最终趋于一稳定值,但其随阻尼系数增大而减小。最后,研制了以LCFBG为敏感元件的传感器,并构建了动态应力场实验平台,实验结果与仿真实验数据基本一致。提供了一种通过实时采集LCFBG全光谱信息探测动态应力场的新方法。     

光纤陀螺光纤环的热应力分布仿真分析方法

针对光纤线圈较容易受温度影响的问题,从热至应力的角度,推导了由热应力导致的光纤陀螺的相位差离散数学公式,并在此基础上,对四级对称绕法绕制的无骨架光纤环建立了有限元模型。结合光纤陀螺工作环境的栽荷和边界条件对其不同温度下的热应力分布进行仿真分析。仿真分析结果表明,光纤环内侧受到的热应力较大,高低温下热应力值分别达到最大和...     

Stress, strain, and NMR

Experimental and ab initio results that demonstrate the effect of stress on the nuclear magnetic resonance spectra of materials are shown. The design of a cell that generates uniaxial compressive stress is presented, and results on gallium phosphide and lead nitrate single crystals that illustrate the observable results of the stress are shown. Tensors that relate stress and strain to changes in the chemical shielding tensors and the electric field gradient tensors are defined formally. The elements of these tensors are then computed by a density functional theory approach that makes use of planewaves and pseudopotentials. The experimental results are interpreted with the aid of the calculations. Extensions to spinning samples and to the interpretation of optical phenomena in materials are discussed.     

Stress effect on the magnetization process in Ni-Cu-Zn ferrite in a weak field

The effect of stress on the magnetization process for Ni-Cu-Zn ferrite was studied by the measurement of the nonsaturated hysteresis loop under external applied stress. A weak field was applied to estimate the effect of stress during the reversal magnetization process. The experimental results show that the nonreversible reversal magnetization process is affected considerably by the compressive stress in the applied field from 0.20 to 0.84 Oe. The compressive stress acts as positive field to impede the nonreversible process which takes place during the reversal magnetization process. The tensile stress had a counter effect but the effect was too small. Stress perpendicular to detecting direction seems to exhibit an effect opposite to that of parallel stress. The sample was toroidal to estimate the differencein the effect of stress between detecting direction and radial direction perpendicular to the detecting direction. The effect of stress in the detecting direction is larger than in the radial direction for the Ni-Cu-Zn ferrite with negative magnetostriction.