Indium content determination related with structural and optical properties of InGaN layers

We studied the structural and optical properties of a set of nominally undoped epitaxial single layers of In_xGa_1−xN (0<x0.2) grown by MOCVD on top of GaN/Al₂O₃ substrates. A comparison of composition values obtained for thin (tens of nanometers) and thick (≈0.5 μm) layers by different analytical methods was performed. It is shown that the indium mole fraction determined by X-ray diffraction, measuring only one lattice parameter strongly depend on the assumptions made about strain, usually full relaxation or pseudomorphic growth. The results attained under such approximations are compared with the value of indium content derived from Rutherford backscattering spectrometry (RBS). It is shown that significant inaccuracies may arise when strain in In_xGa_1−xN/GaN heterostructures is not properly taken into account. Interpretation of these findings, together with the different criteria used to define the optical bandgap of In_xGa_1−xN layers, may explain the wide dispersion of bowing parameters found in the literature. Our results indicate a linear, E_g(x)=3.42−3.86x eV (x0.2), “anomalous” dependence of the optical bandgap at room temperature with In content for In_xGa_1−xN single layers.     

Impedance spectroscopy analysis of AlGaN/GaN HFET structures

For HFET application a series of samples with 30 nm Al_xGa_1−xN (x=0.02–0.4) layers deposited at 1040°C onto optimised 2 μm thick undoped GaN buffers were fabricated. The Al_xGa_1−xN/GaN heterostructures were grown on c-plane sapphire in an atmospheric pressure, single wafer, vertical flow MOVPE system. Electrical properties of the Al_xGa_1−xN/GaN heterostructures and thick undoped GaN layers were evaluated by impedance spectroscopy method performed in the range of 80 Hz–10 MHz with an HP 4192A impedance meter using a mercury probe. The carrier concentration distribution through the layer thickness and the sheet carrier concentration were evaluated. A non-destructive, characterisation technique for verification of device heterostucture quality from the measured C–V and G–V versus frequency characteristics of the heterostructure is proposed.     

Photocurrent measurements on GaAs1−xNx epilayers grown by metalorganic chemical vapor deposition

GaAs_1−xN_x epilayers were grown on a GaAs(0 0 1) substrate by metalorganic chemical vapor deposition. Composition was determined by high resolution X-ray diffraction. Band gap was measured from 77 to 400 K by using photocurrent measurements. The photocurrent spectra show clear near-band-edge peak and their peak energies drastically decrease with increasing nitrogen composition due to band gap bowing in the GaAs_1−xN_x epilayers. Those red shifts were particularly notable for low nitrogen compositions. However, the shifts tended to saturate when the nitrogen composition become higher than 0.98%. When the nitrogen composition is in the range 1.68–3.11%, the measured temperature dependence of the energy band gap was nicely fitted. However, the properties for the nitrogen composition range 0.31–0.98% could not be fitted with a single fitting model. This result indicates that the bowing parameter reaches 25.39 eV for low nitrogen incorporation (x=0.31%), and decreases with increasing nitrogen composition.     

MBE growth of cubic AlyGa1−yN/GaN heterostructures—structural, vibrational and optical properties

Cubic Al_yGa_1−yN/GaN heterostructures on GaAs(0 0 1) substrates were grown by radio-frequency plasma-assisted molecular beam epitaxy. High resolution X-ray diffraction, micro-Raman, spectroscopic ellipsometry, and cathodoluminescence measurements were used to characterize the structural, optical and vibrational properties of the Al_yGa_1−yN epilayers. The AlN mole fraction y of the alloy was varied between 0.07<y<0.20. X-ray diffraction reciprocal space maps demonstrate the good crystal quality of the cubic Al_yGa_1−yN films. The measured Raman shift of the phonon modes of the Al_yGa_1−yN alloy was in excellent agreement with theoretical calculations. Both SE and CL of the Al_yGa_1−yN epilayer showed a linear increase of the band gap with increasing Al-content.     

XPS and electroluminescence studies on SrS1−xSex and ZnS1−xSex thin films deposited by atomic layer deposition technique

SrS_1−xSe_x and ZnS_1−xSe_x thin films were deposited by the atomic layer deposition (ALD) technique using elemental selenium as the Se source, thus avoiding use of H₂Se or organometallic selenium compounds. X-ray diffraction (XRD) analysis showed that the films were solid solutions and X-ray photoelectron spectroscopy (XPS) data showed that the surface of both ZnS_1−xSe_x and SrS_1−xSe_x were covered with an oxide and carbon-containing contaminants from exposure to air. The oxidation of SrS_1−xSe_x extended into the film and peak shifts from sulfate were found on the surface. Luminance measurements showed that emission intensity of the ZnS_1−xSe_x:Mn alternating current thin film electroluminescent (ACTFEL) devices at fixed voltage was almost the same as that of the ZnS:Mn device, while emission intensity of the SrS_1−xSe_x:Ce devices decreased markedly as compared to the SrS:Ce device. Emission colors of the devices were altered only slightly due to selenium addition.     

The effect of the AlxGa1−xN/AIN buffer layer on the properties of GaN/Si(1 1 1) film grown by NH3-MBE

We describe the growth of GaN on Si(1 1 1) substrates with Al_xGa_1−xN/AlN buffer layer by ammonia gas source molecular beam epitaxy (NH₃-GSMBE). The influence of the AlN and Al_xGa_1−xN buffer layer thickness and the Al composition on the crack density of GaN has been investigated. It is found that the optimum thickness is 120 and 250 nm for AlN and Al_xGa_1−xN layers, respectively. The optimum Al composition is between 0.3<x<0.6.     

Study on the Ce substitution effects of BiFeO3 films on ITO/glass substrates

Ce substituted Bi_1−xCe_xFeO₃ (BCFO) films with x=0–0.15 were deposited on indium tin oxide (ITO)/glass substrates by sol–gel process annealed at 500 °C. Rhombohedral phase was confirmed by XRD study and no impure phases were observed till x=0.15. Substantially enhanced ferroelectricity was observed at room temperature due to the substitution of Ce. In the films with x=0.05 and 0.10, the double remnant polarization are 75.5 and 57.7 μC/cm² at an applied field 860 kV/cm. Moreover, the breakdown field was enhanced in the films with Ce substitution.     

The transition from As-doped GaN, showing blue emission, to GaNAs alloys in films grown by molecular beam epitaxy

We have studied the transition from As-doped GaN showing strong blue emission (2.6 eV) at room temperature to the formation of GaN_1−xAs_x alloys for films grown by plasma-assisted molecular beam epitaxy. We have demonstrated that with increasing N-to-Ga ratio there is first an increase in the intensity of blue emission at about 2.6 eV and then a transition to the growth of GaN_1−xAs_x alloy films. We present a model based on thermodynamic considerations, which can explain how this might occur.     

AlGaN-based UV photodetectors

Al_xGa_1−xN alloys are very attractive materials for application to ultraviolet photodetection. AlGaN photoconductors, Schottky photodiodes, metal–semiconductor–metal photodiodes, p–n junction photodetectors and phototransistors have been recently developed. In this work we analyse the performance of AlGaN-based photodetectors, discussing present achievements, and comparing the characteristics of the various photodetector structures developed to date.     

Atomic structure of Al55(Cr1−xMnx)15Si30 metallic glasses observed by neutron diffraction

An atomic structure of Al₅₅(Cr_1−xMn_x)₁₅Si₃₀ (x = 0, 0.49,1) metallic glasses was studied by neutron diffraction. An advantage of the neutron diffraction technique was fully exploited by utilizing the negative scattering length of Mn to form a neutron zero scattering ‘alloy’ for the component Cr_0.51Mn_0.49 in this quaternary Al---(Cr, Mn)---Si alloy. This allows the atomic distribution of the resulting quasibinary Al---Si metallic glass to be derived directly. Moreover, the (Al, Si)---TM (TM = Mn, Cr) and TM---TM pair correlations were also extracted by taking appropriate linear combinations of the atomic structures for the Al₅₅(Cr_1−xMn_x)₁₅Si₃₀ (x = 0, 0.49, 1) metallic glasses. A sharp first peak in the (Al,Si) ---TM pair correlations thus obtained led to the conclusion that a strong attractive interaction exists between (Al, Si) and TM atoms and, hence, that the presence of the TM atoms is responsible for the formation of an amorphous phase.     

Compositional variation in Si-rich SiGe single crystals grown by multi-component zone melting method using Si seed and source crystals

The effect of the supply of depleted Si solute elements on the compositional variation in the Si-rich SiGe bulk crystals was studied using the method which was used to grow Ge-rich SiGe single crystals with a uniform composition. By selecting the proper pulling rate, we can obtain Si-rich Si_1−xGe_x bulk crystals with uniform composition of x=0.1 without using the supply mechanism of depleted Si solute elements. When the supply mechanism of Si solute elements was used, the initial composition in Si-rich SiGe crystals can be much more easily determined by controlling the growth temperature than that in Ge-rich crystals because the Si seed crystal is not melted down. The supply of Si solute elements is very effective to change the compositional variation even for Si-rich SiGe crystals.     

Characteristic crystal growth from amorphous WO3 film by vacuum heating

Selective growth of WO₂, W and WO_3−x crystals from amorphous WO₃ film by vacuum heating at 400–900°C was clarified. The grown WO_3−x crystals were incommensurate structure based on crystallographic share structure. The growth process of WO₂ crystal in the amorphous film was directly observed at high temperature in the electron microscope. The growth front of the WO₂ crystal consumes WO₃ microcrystallites with various orientations. The growth speed of the WO₂ depended on WO₃ microcrystallites orientation. The origin of the wavy growth front of WO₂ was due to an orientation dependence of the WO₃ microcrystallites.     

New aluminium precursors for MOMBE (CBE): a comparative study

Recently different new Al precursors have been developed to improve the electrical and optical quality of AlGaAs layers grown by MOMBE (CBE), since AlGaAs layers still suffer from the high incorporation of oxygen and carbon. Three approaches are introduced and results obtained from Al_xGa_1−xAs layers (0 < x ≤ 1) are discussed. APAH, a double ring structure molecule, was found to yield AlGaAs layers with high contents of carbon and nitrogen. The use of an Alane-adduct decreases impurity concentrations and improves optical properties. However, TIBAl is superior and provides highest PL response together with carrier concentrations below p = 10¹⁶ cm^-3. Even though the concept of coordinative saturation is promising, results achieved by TIBAl showed that trialkyls could also be well suited for AlGaAs, assuming that they are properly synthesized.     

Properties of Si-rich SiO2 films by RF magnetron sputtering

Si-rich silicon oxide (SiO_x, 1<x<2) films were prepared by RF magnetron reactive sputtering or co-sputtering on the Si(1 1 1) substrates. X-ray diffraction patterns showed that the peak of silicon nanocrystals (NCs), separated from SiO_x films, had (1 1 1) preferred orientation. The results of scanning electron microscopy indicated the Si NCs uniting into clusters. We demonstrated that the photoluminescence (PL) peaks at 650 nm was caused by defect center. In particular, we discussed the correlation between the PL and the structure of SiO_x films. The mean size of the Si NCs was estimated to be about 3 nm by the PL peak position.     

Heavily carbon-doped p-type (In)GaAs grown by gas-source molecular beam epitaxy using diiodomethane

Heavily carbon-doped p-type In_xGa_1−xAs (0≤x<0.49) was successfully grown by gas-source molecular beam epitaxy using diiodomethane (CH₂I₂), triethylindium (TEIn), triethylgallium (TEGa) and AsH₃. Hole concentrations as high as 2.1×10²⁰ cm⁻³ were achieved in GaAs at an electrical activation efficiency of 100%. For In_xGa_1−xAs, both the hole and the atomic carbon concentrations gradually decreased as the InAs mole fraction, x, increased from 0.41 to 0.49. Hole concentrations of 5.1×10¹⁸ and 1.5×10¹⁹ cm⁻³ for x = 0.49 and x = 0.41, respectively, were obtained by a preliminary experiment. After post-growth annealing (500°C, 5 min under As₄ pressure), the hole concentration increased to 6.2×10¹⁸ cm⁻³ for x = 0.49, probably due to the activation of hydrogen-passivated carbon accepters.     

Characterization and growth of ZnSTe epilayers by hot-wall epitaxy

ZnS_1−xTe_x epilayers were grown on GaAs(1 0 0) substrates by hot-wall epitaxy in a wide range of Te composition. The Te composition was determined by Rutherford backscattering spectrometry and the lattice constant was measured by double-crystal rocking curve. It was found that the lattice of the epilayer matches well with that of the substrate at x=0.37 as expected by Vegard's rule, and the energy gap was also determined as a function of Te composition by spectrophotometer. It showed that a quadratic relation with the composition: E_g(x)=3.71−5.27x+3.83x². Photoluminescence characteristics were also studied.     

Heavily carbon-doped p-type InGaAs by MOMBE

Carbon-doped In_xGa_1−xAs layers (x=0−0.96) were grown by metalorganic molecular beam epitaxy (MOMBE) using trimethylgallium (TMG), solid arsenic (As₄) and solid indium (In) as sources of Ga, As and In, respectively. The carrier concentration is strongly affected by growth temperature and indium beam flux. Heavy p-type doping is obtained for smaller In compositions. The hole concentration decreases with the indium composition from 0 to 0.8, and then the conductivity type changes from p to n at x=0.8. Hole concentrations of 1.0×10¹⁹ and 1.2×10¹⁸ cm^-3 are obtained for x=0.3 and 0.54, respectively. These values are significantly higher than those reported on carbon-doped In_xGa_1−xAs by MBE. Preliminary results on carbon-doped GaAs/In_xGa_1−xAs strained layer superlattices are also discussed.     

Growth of Cu(AlxGa1−x)SSe pentenary alloy crystals by iodine chemical vapor transport method

Single crystals of Cu(Al_xGa_1−x)SSe pentenary alloys were successfully grown by the vapor transport technique using iodine as a transport agent. Systematic measurements of the basic crystal properties were carried out using powder X-ray, photoluminescence (PL), photoreflectance (PR), and Van der Pauw methods. Dependence of the lattice constants, exciton transition energies, and PL peak energies on Al composition, x, were examined in detail. The lattice constants obeyed Vegard's law. A quadratic dependence of exciton transition energies on x was found. The broadening parameters in the PR spectrum increase monotonically with increasing x, the results showing that the crystal quality degrades with increasing x. Exciton-related PL peaks were found for 0 ≤ x ≤ 0.77 at 77 K.     

Heteroepitaxy of CdTe on tilting Si(2 1 1) substrates by molecular beam epitaxy

CdTe(2 1 1)B epilayers were grown on 3 in Si(2 1 1) substrates which misoriented 0–10° toward [1 1 1] by molecular beam epitaxy (MBE). The relationship of X-ray double-crystal rocking curve (XRDCRC) FWHM and deflection angle from CdTe(2 1 1) to Si(2 1 1) was studied. For 4.2–4.5 μm CdTe, the best value of FWHM 83 arcsec was achieved while deflection angle is 2.76°. A FWHM wafer mapping indicated a good crystalline uniformity of 7.4 μm CdTe on tilting Si(2 1 1), with FWHM range of 60–72 arcsec. The shear strains of these epilayers were analyzed, using reciprocal lattice points of symmetric and asymmetric reflections measured by high-resolution multi-crystal multi-reflection X-ray diffractometer (HRMCMRXD). It was found that the shear strain angle of epilayer is effectively reduced by using proper tilting Si(2 1 1) substrate. It was also proved that the lattice parameter of CdTe(2 1 1)B is affected by the shear strain and thermal strain.     

Low-temperature growth of epitaxial layers of ZnSe1−xTex solid solutions

The layers of ZnSe_1−xTe_x (0 < x < 1.0) solid solutions have been grown by liquid-phase epitaxy in a closed tube at 620–680 °C. Zinc chloride served as a solvent. ZnTe and ZnSe crystals were used as sources and substrates with orienting surfaces (110) and (111) for ZnSe and (110) for ZnTe. The composition of the grown layer was specified by the relative content of the ZnSe and the ZnTe in the solution and was controlled by X-ray analysis. The position of the exciton bands in the photoluminescence spectra of ZnSe_1−xTe_x over the interval 0.3 < x < 1.0 is in agreement with the free exciton energies calculated for these compositions. Relatively low-ohmic (of about 10² Ω cm) epitaxial layers of ZnSe_1−xTe_x solid solutions were grown.