Application of Nafion／Cobalt Hexacyanoferrate Chemically Modified Electrodes for the Determination of Electroinactive Cations by Ion Chromatography

Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｉｏｎｃｈｒｏｍａｔｏｇｒａｐｈｙ (ＩＣ)ｈａｓｂｅｅｎｒｅｃｏｇｎｉｚｅｄａｓａｕｓｅｆｕｌｍｅｔｈｏｄｆｏｒｔｈｅｓｅｐａｒａｔｉｏｎｏｆｉｎｏｒｇａｎｉｃａｎｉｏｎｓａｎｄｃａｔｉｏｎｓｓｉｎｃｅｉｔｓｉｎｔｒｏｄｕｃｔｉｏｎｂｙＳｍａｌｌｅｔａｌ .ｉｎ 1975 .1ＡｓｉｇｎｉｆｉｃａｎｔｔｒｅｎｄｉｎｔｈｅｄｅｖｅｌｏｐｍｅｎｔｏｆＩＣｍｅｔｈｏｄｉｓｓｅａｒｃｈｆｏｒｓｅｎｓｉｔｉｖｅａｎｄｕｎｉｖｅｒｓａｌｄｅｔｅｃｔｉｏｎｍｅｔｈｏｄｓ .Ｔｈｅｍａｉｎｄｅｔ…     

Sensitive adsorptive stripping voltammetric method for direct determination of trace concentration of lead in the presence of cupferron in natural water samples

This paper reports the use of an adsorptive voltammetric technique for Pb(II) determination using cupferron as a selective complexing agent. After accumulation of the complex onto a hanging mercury drop electrode, the electrode potential was scanned with differential pulse modulation and the reduction current of lead was observed at about??0.5?V. Under optimum conditions (5?×?10^?4?mol?L^?1 cupferron concentration, 0.1?mol?L^?1 acetate buffer (pH 5.5), adsorption at??50?mV for 30?s) the detection limit was 5.1?×?10^?10?mol?L^?1. The relative standard deviation of five measurements for low lead concentration was 3.1%. The accuracy of the method was tested by analysing certified reference material (SPS-WW1 Waste Water). Finally, the method was successfully applied to the determination of Pb(II) in river water samples without any pretreatments.     

Determination of Trace Copper by Adsorptive Voltammetry Using a Multiwalled Carbon Nanotube Modified Carbon Paste Electrode

A new method for the determination of trace copper was described. A multiwalled carbon nanotube modified carbon paste electrode was prepared and the adsorptive voltammetric behavior of copper‐alizarin red S (ARS) complex at the modified electrode was investigated. By use of the second‐order derivative linear sweep voltammetry, it was found that in 0.04 mol/L acetate buffer solution (pH 4.2) containing 4×10^?6 mol/L ARS, when accumulation potential is 0 mV, accumulation time is 60 s and scan rate is 100 mV/s, the complex can be adsorbed on the surface of the electrode, yielding one sensitive reduction peak at ?172 mV (vs. SCE). The peak current of the complex is proportional to the concentration of Cu(II) in the range of 2.0×10^?11–4.0×10^?7 mol L^?1 with a detection limit (S/N=3) of 8.0×10^?12 mol/L (4 min accumulation). The proposed method was successfully applied to the determination of copper in biological samples with satisfactory results, the recoveries were found to be 96%–102%.     

Electrochemical Behavior of 6-Mercapto-Purine at Hanging Copper Amalgam Dropping Electrode and Its Trace Determination by Differential Pulse Adsorption Cathodic Stripping Voltammetry

Abstract

The electrochemical behavior of 6-MP was studied by cyclic voltammetry at a hanging copper amalgam dropping electrode (HCADE). It was found that 6-MP could form a complex with the Cu(II) stripped from the HCADE, showing a new peak at ?0.19V in the medium of 0.1mol/L LiClO₄-0.5mol/L HClO₄ solution. The mechanism of the reaction was proposed. This new peak was sensitive and could be used for the determination of trace 6-MP by differential pulse adsorption cathodic stripping voltammetry (DPAdCSV). The linear range was from 3.6×10^?10 to 5.3×10^?6 mol/L, and the detection limit was about 1.2×10^?10 mol/L (S/N=3). The method was also successfully applied to the determination of 6-MP in pharmaceutical tablets.     

Sol—Gel Derived Carbon Ceramic Electrode Bulk—Modified with Tris（1,10—phenanthroline—5,6—dione） iron （Ⅱ）Hexafluorophosphate and Its Use as an Amperometric Iodate Sensor

A surface‐renewable tris(1, 10‐phenanthroline‐5, 6‐dione) iron (D) hexafluorophosphate (FePD) modified carbon ceramic electrode was constructed by dispersing FePD and graphite powder in methyltrimethoxysilane (MTMOS) based gels. The FePD‐modified electrode presented pH‐dependent voltammetric behavior, and its peak currents were diffusion‐controlled in 0.1 mol/L Na₂SO₄ + H₂SO₄ solution (pH = 0.4). In the presence of iodate, dear electrocatalytic reduction waves were observed and thus the chemically modified electrode was used as an amperometric sensor for iodate in common salt. The linear range, sensitivity, detection limit and response time of the iodate sensor were 5 × 10^?6–1 × 10^?2 mol/L, 7.448 μA·L/ mmol, 1.2 × 10^?6 mol/L and 5 s, respectively. A distinct advantage of this sensor is its good reproducibility of surface‐renewal by simple mechanical polishing.     

A Metal‐Free Approach Based on Graphene Oxide‐Modified Electrode for Monitoring the Photoelectrocatalytic Degradation of EDTA

A novel voltammetric method for the sensitive determination of ethylenediaminetetraacetic acid (EDTA) was developed based on a graphene oxide (GO) modified electrode. In acetate buffer solution, GO showed a voltammetric response composed of a sharp anodic peak and a weak cathodic peak. When EDTA was present in the solution, the voltammetric response of GO was suppressed. Under optimum conditions, the response of the GO‐modified electrode was inversely proportional to the concentration of EDTA from 6.0×10^?7 to 1.0×10^?4 mol/L. Using such a GO‐based voltammetry, the effective photoelectrocatalytic degradation of EDTA over a TiO₂ film electrode was evaluated and some influencing factors were investigated.     

Voltammetric Determination of Rutin Using a Carbon Composite Electrode Modified with Copper(II)-Resin

Abstract

The preparation and electrochemical characterization of a carbon composite electrode modified with copper(II)-resin as well as its behavior toward rutin were investigated using cyclic and linear sweep voltammetry. The best voltammetric response was observed for a composite composition of 20% (m/m) copper(II)-resin, 0.10 mol L^?1 KNO₃/10^?6 mol L^?1 HNO₃ solution (pH 6.0) as the supporting electrolyte, and a scan rate of 50 mVs^?1. A linear voltammetric response for rutin was obtained in the concentration range from 9.90 × 10^?7 to 8.07 × 10^?6 mol L^?1, with a detection limit of 2.65 × 10^?8 mol L^?1. The proposed electrode was useful for the quality control and routine analysis of rutin in pharmaceutical formulations.     

Sensitive electrochemical determination of Sudan II in food samples using a poly(aminosulfonic acid) modified glassy carbon electrode

In this paper, a novel poly(aminosulfonic acid) modified glassy carbon electrode (PASA/GCE) for the determination of Sudan II was fabricated through electrochemical polymerizat ion. The electrochemical behavior of Sudan II at the modified electrode was studied by cyclic voltammetry. Results show that the modified electrode exhibits excellent electrocatalytic activity toward the electrochemical redox reaction of Sudan II. Under optimal experimental conditions, the oxidation peak current is linearly proportional to the concentration of Sudan II in the ranges of 4.0 × 10^?8 to 1.0 × 10^?6 mol L^?1 and 1.0 × 10^?6 to 1.2 × 10^?5 mol L^?1. The linear regression equations are i _pa(A) = 2.87c + 3.74 × 10^?6, r = 0.9977 and i _pa(A) = 0.78c + 6.11 × 10^?6, r = 0.9982, respectively, and the detection limit is 4.0 × 10^?9 mol L^?1. The novel method shows good recovery, reproducibility and sensitivity for the voltammetric determination of Sudan II in food samples.     

CuO Crystalline Modified Glassy Carbon Electrodes for Anodic Amperometric Determination of Hydrogen Peroxide

As an alternative selection of electrocatalytic surface modifier, the electrochemically generated copper oxides is re‐ investigated by using cyclic voltammetry (CV), scanning electron microscopy (SEM) and X‐ray photoelectron spectroscopy (XPS). Interesting phenomena have been found, which indicate that the electrodeposition from the Cu²⁺ solution under cyclic voltammetric conditions can generate a transparent Cu(OH)₂ crystalline on the surface of glassy carbon electrodes, and this crystalline can be further transferred to a novel cubic opaque CuO crystalline of about 300 nm in size by second step of cyclic voltammetry in pH 12 NaOH solution. The final electrode (denoted as nano‐CuO/GCE) can catalyze the oxidation (as well as the reduction) of H₂O₂ in basic solutions. It shows pH dependent three‐part catalytic mechanism in the range from pH 7 to pH 14. In 0.10 mol/L NaOH solution, the amperometric response at 0.15 V (vs. SCE) can give a current sensitivity as high as 139 mA/(mol·L^?1) in the rage of 5.0×10^?7?6.0×10^?4 mol/L with a lower detection limit (s/n=3) of 2.5×10^?8 mol/L, and a current sensitivity of 78.4 mA/(mol·L^?1) in the rage of 6.0×10^?4–2.0×10^?3 mol/L. This electrode also has excellent reproducibility and stability. The mechanisms for the two steps of preparation and the catalytic reactions are proposed. The nano‐CuO crystalline modified electrode may have more applications in the field of electrochemical sensing.     

Captopril Modified Silver Electrode and Its Application to the Electroanalysis of Hemoglobin

Abstract

Captopril, 1-[(2S)-3-mercapto-2-methyl-1-oxopropyl]-L-Proline, can be deposited onto a silver electrode by a covalent bonding method to give a long-lived and stable chemically modified electrode(CME). Since the CME is prepared with a reaction between captopril and the substrate silver, the CME being prepared by this method is very stable. Furthermore, Hemoglobin(Hb) exhibits excellent voltammetric response at the modified electrode. Differential pulse voltammetric(DPV) measurements of the protein with this CME reveal the existence of a linear relationship between the anodic peak current and the concentration of Hb in the range of 2×10^?6 ～ 5×10^?5 mol/L. The detection limit is 8×10^?7 mol/L and the relative standard deviation of results is 5% for 6 successive determinations at 2×10_-5 mol/L. The determination of Hb for a real example is carried out.     

Carbon Composite Electrode Modified with Copper(II) Phosphate Immobilized in a Polyester Resin for Voltammetric Determination of Catechin in Teas

A carbon composite electrode modified with copper (II) phosphate immobilized in a polyester resin (Cu₃(PO₄)₂-Poly) was proposed for the voltammetric determination of catechin in teas. The modified electrode allows the determination of catechin (CAT) at lower potential than that observed at an unmodified electrode. Several parameters that can influence the voltammetric response of the proposed electrode such as carbon composite composition, pH of electrolyte, and others were investigated. The peak current was proportional to the concentration of catechin in the range from 9.9 × 10^?8 to 1.2 × 10^?6 mol L^?1, with a detection limit of 5.8 × 10^?8 mol L^?1. The stability and repeatability of the electrode for the determination of catechin were discussed, and the modified electrode was applied with success in the determination of catechin in teas.     

Determination of Antimony(III) by Differential Pulse Voltammetry Using a Gold Nanoparticle–Ionic Liquid–Graphene-Modified Selenium-Doped Carbon Paste Electrode

A simple and sensitive differential pulse stripping voltammetric method was developed for the determination of antimony(III) using a selenium-doped carbon paste electrode modified with an ionic liquid, graphene, and gold nanoparticles. The conditions, including the mass of graphene, concentration of hydrochloric acid, deposition potential, and deposition time were optimized by single-factor experiments. Under the optimal conditions, a linear equation of I_Sb(III) (µA)?=??16.9882???11.0929 c (µmol/L) (R?=?0.9965) and a detection limit of 2.7?×?10^?8?mol/L were obtained for 8.0?×?10^?8 to 4.8?×?10^?6?mol/L antimony(III). The response shows that the sensor enhances the sensitivity of antimony due to the high conductivity and large surface areas of the ionic liquid, graphene, and gold nanoparticles. This electrode may provide a new sensing platform for the determination of antimony.     

Fast Simultaneous Adsorptive Stripping Voltammetric Determination of Ni(II) and Co(II) at Lead Film Electrode Plated on Gold Substrate

A fast adsorptive stripping voltammetric procedure for simultaneous determination of Ni(II) and Co(II) in the presence of nioxime as a complexing agent at an in situ plated lead film electrode was described. The time of determination of these ions was shortened due to the application of gold as a substrate for lead film. At gold substrate lead film formation and accumulation of Ni(II) and Co(II) complexes with nioxime proceeds simultaneously. To obtain a stable signals for both ions a simple procedure of activation of the electrode was proposed. Calibration graphs for an accumulation time of 20 s were linear from 5×10^?9 to 1×10^?7 mol L^?1 and from 5×10^?10 to 1×10^?8 mol L^?1 for Ni(II) and Co(II), respectively. The procedure with the application of a lead film electrode on a gold substrate was validated in the course of Ni(II) and Co(II) determination in certified reference materials.     

Trace determination of vardenafil hydrochloride in commercial formulation and human serum by adsorptive anodic stripping voltammetry at a carbon paste electrode

The electrochemical behavior of vardenafil HCl (VRL) at a carbon paste electrode (CPE) was investigated by cyclic voltammetry, and the mechanism of its oxidation was suggested and discussed. A simple Nujol-based CPE in combination with a sensitive square-wave adsorption anodic stripping voltammetry method was described for trace determination of VRL. The described method showed excellent performance for trace determination of VRL in its formulation “Levitra® tablets” without interference from excipients. The results were statistically compared with those obtained with an established HPLC method; nonsignificant differences were found between the described voltammetric and HPLC methods. The described stripping voltammetric method is highly sensitive (limit of detection?=?3?×?10^?10?mol?L^?1 and limit of quantitation?=?1?×?10^?9?mol?L^?1). It was successfully applied for the determination of VRL in spiked human serum without the necessity for pretreatment and/or time-consuming extraction steps prior to the analysis.     

Simultaneous Determination of Dihydroxybenzene Isomers at MWCNTs/β‐Cyclodextrin Modified Carbon Ionic Liquid Electrode in the Presence of Cetylpyridinium Bromide

Simultaneous determination of dihydroxybenzene isomers was investigated at a multi‐wall carbon nanotubes (MWCNTs)/β‐cyclodextrin composite modified carbon ionic liquid electrode in phosphate buffer solution (pH 7.0, 1/15 mol/L) in the presence of cationic surfactant cetylpyridinium bromide (CPB). With the great enhancement of surfactant CPB, the voltammetric responses of dihydroxybenzene isomers were more sensitive and selective. The oxidation peak potential of hydroquinone was about 0.024 V, catechol was about 0.140 V and resorcinol 0.520 V in differential pulse voltammetric (DPV) measurements, which indicated that the dihydroxybenzene isomers could be separated entirely. The electrode showed wide linear behaviors in the range of 1.2×10^?7–2.2×10^?3, 7.0×10^?7–1.0×10^?3, 2.6×10^?6–9.0×10^?4 mol/L for hydroquinone, catechol and resorcinol, respectively. And the detection limits of the three dihydroxybenzene isomers were 4.0×10^?8, 8.0×10^?8, 9.0×10^?7 mol/L, respectively. The proposed method could be applied to the determination of dihydroxybenzene isomers in artificial wastewater, and the recovery was from 97.4% to 104.2%.     

Self‐Assembled Submonolayer of β‐Cyclodextrins on Gold Electrode for the Selective Determination of 4‐Aminobiphenyl

The formation of an inclusion complex between 4‐aminobiphenyl (4‐AB) and β‐cyclodextrin molecules (β‐CD), allows the use of thiolated β‐CDs as chemi‐adsorbed material on a Au electrode as a self‐assembled submonolayer for the selective square wave voltammetric determination of 4‐AB. The submonolayer was characterized by reductive desorption and an association constant of 1.2×10⁴ L/mol was obtained. The optimization of variables yielded a linear dependence of ip/4‐AB concentration in the range of 10^?5 to 10^?4 mol/L. The selectivity of the method was evaluated in the presence of other aromatic amines obtaining better results with the modified electrode. This methodology was applied to the voltammetric determination of 4‐AB in wastewater samples.     

Electrochemistry and Voltammetric Determination of Adenosine with N‐Hexylpyridinium Hexafluorophosphate Modified Electrode

An ionic liquid N‐hexylpyridinium hexafluorophosphate (HPPF₆) modified carbon paste electrode was fabricated for the sensitive voltammetric determination of adenosine in this paper. Carbon ionic liquid electrode (CILE) was prepared by mixing graphite powder and HPPF₆ together and the CILE was characterized by scanning electron microscopy (SEM) and electrochemical methods. The electrochemical behaviors of adenosine on the CILE were studied carefully. Compared with the traditional carbon paste electrode (CPE), a small negative shift of the oxidation peak potential appeared with greatly increase of the oxidation peak current, which indicated the presence of ionic liquid in the carbon paste not only as the binder but also as the modifier and promoter. Under the optimal conditions the oxidation peak current increased with the adenosine concentration in the range from 1.0×10^?6 mol/L to 1.4×10^?4 mol/L with the detection limit of 9.1×10^?7 mol/L (S/N=3) by differential pulse voltammetry. The proposed method was applied to the human urine samples detection with satisfactory results.     

Electrochemical Oxidation of Ibuprofen and Its Voltammetric Determination at a Boron‐Doped Diamond Electrode

The electrochemical oxidation of ibuprofen at a boron‐doped diamond electrode (BDDE) and its voltammetric determination is reported for the first time. A well‐defined oxidation peak was observed at around 1.6 V in 0.1 mol L^?1 H₂SO₄ solution with 10 % (v/v) ethanol at the BDDE surface activated by either cathodic or anodic pretreatments. A differential‐pulse voltammetric method for the determination of ibuprofen in pharmaceutical formulations was optimized with a detection limit of 5 µmol L^?1 and compared with the British Pharmacopeia method.     

Electrooxidation of Some Antifungal Agents and Their Square-Wave Voltammetric Determination in Cosmetics and Pharmaceutics

Ketoconazole and methylparaben were electrochemically studied using cyclic and square wave voltammetric (SWV) techniques at glassy carbon electrode. The oxidation of methylparaben and ketoconazole—the mechanism under scrutiny in this study—was characterized by irreversibility and the features of a pH-dependent diffusion controlled process. Optimal conditions for the electrochemical behavior of methylparaben and ketoconazole were investigated [e.g., potential window, supporting electrolyte and potential scan rates, the dependence of current intensities and potentials on pH, the linear relationship between the peak current and the concentration, limit of detection (LOD), limit of quantification (LOQ), recovery, and accuracy]. The proposed procedures were used for the determination of studied substances in cosmetic and pharmaceutical samples for methylparaben and ketoconazole, respectively. The current-concentration plot for methylparaben was linear over the range from 1 · 10^?5 to 2.02 · 10^?4 mol L^?1 in 0.1 mol L^?1 HClO₄. The linear response for ketoconazole was obtained in the range of 3.2 · 10^?7–9.58 · 10^?6 mol L^?1 in NH₃-NH₄Cl buffer at pH 9. The repeatability and reproducibility of the methods for the studied substances were also determined. Furthermore, results obtained by the proposed methods have been compared with high-performance liquid chromatographic methods.     

Adsorptive Voltammetric Behaviors of Resveratrol at Graphite Electrode and its Determination in Tablet Dosage Form

The adsorptive voltammetric behavior of resveratrol was studied at a graphite electrode in B‐R buffer (pH = 6.0) solution using adsorptive cyclic voltammetric technique. The oxidation of resveratrol is an irreversible adsorption controlled process. The oxidation mechanism was proposed and discussed in this work. The dependence of the current on pH and the concentration and nature of buffer were investigated to optimize the experimental conditions for the determination of resveratrol. It was found that in the range of 8.0 × 10^?9 ～ 2.0 × 10^?6 mol/L, the currents measured by differential pulse voltammetries presented a good linear property as a function of the concentrations of resveratrol. In addition, validation parameters, such as reproducibility, sensitivity and recovery were evaluated as well. The proposed method was also successfully applied for the determination of resveratrol in Chinese patent medicine with good results.