Edge termination study and fabrication of a 4Hben SiC junction barrier Schottky diode

The 4H-SiC junction barrier Schottky (JBS) diodes terminated by field guard rings and offset field plate are designed, fabricated and characterized. It is shown experimentally that a 3-μm P-type implantation window spacing gives an optimum trade-off between forward drop voltage and leakage current density for these diodes, yielding a specific on-resistance of 8.3 mΩ·cm². A JBS diode with a turn-on voltage of 0.65 V and a reverse current density less than 1 A/cm² under 500 V is fabricated, and the reverse recovery time is tested to be 80 ns, and the peak reverse current is 28.1 mA. Temperature-dependent characteristics are also studied in a temperature range of 75 ℃-200 ℃. The diode shows a stable Schottky barrier height of up to 200 ℃ and a stable operation under a continuous forward current of 100 A/cm².     

Modeling of 4H--SiC multi-floating-junction Schottky barrier diode

This paper develops a new and easy to implement analytical model for the specific on-resistance and electric field distribution along the critical path for 4H-SiC multi-floating junction Schottky barrier diode. Considering the charge compensation effects by the multilayer of buried opposite doped regions, it improves the breakdown voltage a lot in comparison with conventional one with the same on-resistance. The forward resistance of the floating junction Schottky barrier diode consists of several components and the electric field can be understood with superposition concept, both are consistent with MEDICI simulation results. Moreover, device parameters are optimized and the analyses show that in comparison with one layer floating junction, multilayer of floating junction layer is an effective way to increase the device performance when specific resistance and the breakdown voltage are traded off. The results show that the specific resistance increases 3.2 mΩ·cm 2 and breakdown voltage increases 422 V with an additional floating junction for the given structure.     

套刻偏差对4H-SiC 浮动结结势垒肖特基二极管的影响研究

4H-SiC浮动结结势垒肖特基二极管与常规结势垒肖特基二极管相比在 相同的导通电阻条件下具有更高的击穿电压. 由p⁺埋层形成的浮动结与主结p⁺区 之间的套刻对准是实现该结构的一项关键技术. 二维模拟软件ISE的模拟结果表明, 套刻偏差的存在会明显影响器件的击穿特性, 随着偏差的增大击穿电压减小. 尽管主结和埋层的交错结构与对准结构具有相似的击穿特性, 但是当正向电压大于2 V后, 交错结构的串联电阻更大.     

Design optimization of high breakdown voltage vertical GaN junction barrier Schottky diode with high-K/low-K compound dielectric structure

A vertical junction barrier Schottky diode with a high-$K$/low-$K$ compound dielectric structure is proposed and optimized to achieve a high breakdown voltage (BV). There is a discontinuity of the electric field at the interface of high-$K$ and low-$K$ layers due to the different dielectric constants of high-$K$ and low-$K$ dielectric layers. A new electric field peak is introduced in the n-type drift region of junction barrier Schottky diode (JBS), so the distribution of electric field in JBS becomes more uniform. At the same time, the effect of electric-power line concentration at the p-n junction interface is suppressed due to the effects of the high-$K$ dielectric layer and an enhancement of breakdown voltage can be achieved. Numerical simulations demonstrate that GaN JBS with a specific on-resistance ($R_{\rm on, sp}$) of 2.07 m$\Omega\cdot$cm$^{2}$ and a BV of 4171 V which is 167% higher than the breakdown voltage of the common structure, resulting in a high figure-of-merit (FOM) of 8.6 GW/cm$^{2}$, and a low turn-on voltage of 0.6 V.     

SiC Schottky结反向特性的研究

对Ti/6H-SiC Schottky结的反向特性进行了测试和理论分析，提出了一种综合的包括SiC Schottky结主要反向漏电流产生机理的反向隧穿电流模型，该模型考虑了Schottky势垒不均匀性、Ti/SiC界面层电压降和镜像力对SiC Schottky结反向特性的影响，模拟结果和测量值的相符说明了以上所考虑因素是引起SiC Schottky结反向漏电流高于常规计算值的主要原因.分析结果表明在一般工作条件下SiC Schottky结的反向特性主要是由场发射和热电子场发射电流决定的.     

Numerical and experimental study of the mesa configuration in high-voltage 4H–SiC PiN rectifiers

The effect of the mesa configuration on the reverse breakdown characteristic of a SiC PiN rectifier for high-voltage applications is analyzed in this study.Three geometrical parameters,i.e.,mesa height,mesa angle and mesa bottom corner,are investigated by numerical simulation.The simulation results show that a deep mesa height,a small mesa angle and a smooth mesa bottom(without sub-trench) could contribute to a high breakdown voltage due to a smooth and uniform surface electric field distribution.Moreover,an optimized mesa structure without sub-trench(mesa height of 2.2 μm and mesa angle of 20°) is experimentally demonstrated.A maximum reverse blocking voltage of 4 kV and a forward voltage drop of 3.7 V at 100 A/cm~2 are obtained from the fabricated diode with a 30-μm thick N~- epi-layer,corresponding to 85% of the ideal parallel-plane value.The blocking characteristic as a function of the JTE dose is also discussed for the PiN rectifiers with and without interface charge.     

New GaN Schottky barrier diode employing a trench on AlGaN/GaN heterostructure

A new GaN Schottky barrier diode employing a trench structure, which is proposed and fabricated, successfully decreases a forward voltage drop without sacrificing any other electric characteristics. The trench is located in the middle of Schottky contact during a mesa etch. The Schottky metal of Pt/Mo/Ti/Au is e-gun evaporated on the 300 nm-deep trench as well as the surface of the proposed GaN Schottky barrier diode. The trench forms the vertical Au Schottky contact and lateral Pt Schottky contact due to the evaporation sequence of Schottky metal. The forward voltage drops of the proposed diode and conventional one are 0.73 V and 1.25 V respectively because the metal work function (5.15 eV) of the vertical Au Schottky contact is considerably less than that of the lateral Pt Schottky contact (5.65 eV). The proposed diode exhibits the low on-resistance of 1.58 mΩ cm² while the conventional one exhibits 8.20 mΩ cm² due to the decrease of a forward voltage drop.     

Simulation study of a mixed terminal structure for 4H-SiC merged PiN/Schottky diode

In this paper, a mixed terminal structure for the 4H-SiC merged PiN/Schottky diode (MPS) is investigated, which is a combination of a field plate, a junction termination extension and floating limiting rings. Optimization is performed on the terminal structure by using the ISE-TCAD. Further analysis shows that this structure can greatly reduce the sensitivity of the breakdown voltage to the doping concentration and can effectively suppress the effect of the interface charge compared with the structure of the junction termination extension. At the same time, the 4H-SiC MPS with this termination structure can reach a high and stable breakdown voltage.     

结终端采用JTE保护技术的4H-SiC PiN二极管模拟和研制

利用二维器件模拟软件ISE-TCAD 10.0,对结终端采用结扩展保护技术的4H-SiC PiN二极管平面器件进行反向耐压特性的模拟,并获得许多有价值的模拟数据.依据所得的模拟数据进行此种二极管器件的研制.实验测试表明,此二极管的模拟优化数据与实验测试的结果一致性较好,4H-SiC PiN二极管所测得到的反向电压达1600 V,该反向耐压数值达到理想平面结的击穿耐压90%以上.     

High-temperature current conduction through three kinds of Schottky diodes

Fundamentals of the Schottky contacts and the high-temperature current conduction through three kinds of Schottky diodes are studied. N-Si Schottky diodes, GaN Schottky diodes and AlGaN/GaN Schottky diodes are investigated by I--V--T measurements ranging from 300 to 523~K. For these Schottky diodes, a rise in temperature is accompanied with an increase in barrier height and a reduction in ideality factor. Mechanisms are suggested, including thermionic emission, field emission, trap-assisted tunnelling and so on. The most remarkable finding in the present paper is that these three kinds of Schottky diodes are revealed to have different behaviours of high-temperature reverse currents. For the n-Si Schottky diode, a rise in temperature is accompanied by an increase in reverse current. The reverse current of the GaN Schottky diode decreases first and then increases with rising temperature. The AlGaN/GaN Schottky diode has a trend opposite to that of the GaN Schottky diode, and the dominant mechanisms are the effects of the piezoelectric polarization field and variation of two-dimensional electron gas charge density.     

Study and optimal simulation of 4H-SiC floating junction Schottky barrier diodes’ structures and electric properties

This paper stuides the structures of 4H-SiC floating junction Schottky barrier diodes. Some structure parameters of devices are optimized with commercial simulator based on forward and reverse electrical characteristics. Compared with conventional power Schottky barrier diodes, the devices are featured by highly doped drift region and embedded floating junction layers, which can ensure high breakdown voltage while keeping lower specific on-state resistance, and solve the contradiction between forward voltage drop and breakdown voltage. The simulation results show that with optimized structure parameter, the breakdown voltage can reach 4.36 kV and the specific on-resistance is 5.8 mΩ·cm2 when the Baliga figure of merit value of 13.1 GW/cm2 is achieved.     

Prediction of barrier inhomogeneities and carrier transport in Ni-silicided Schottky diode

Based on Quantum Mechanical (QM) carrier transport and the effects of interface states, a theoretical model has been developed to predict the anomalous current-voltage (I-V) characteristics of a non-ideal Ni-silicided Schottky diode at low temperatures. Physical parameters such as barrier height, ideality factor, series resistance and effective Richardson constant of a silicided Schottky diode were extracted from forward I-V characteristics and are subsequently used for the simulation of both forward and reverse I-V characteristics using a QM transport model in which the effects of interface state and bias dependent barrier reduction are incorporated. The present analysis indicates that the effects of barrier inhomogeneity caused by incomplete silicide formation at the junction and the interface states may change the conventional current transport process, leading to anomalous forward and reverse I-V characteristics for the Ni-silicided Schottky diode.     

Trapezoid mesa trench metal-oxide semiconductor barrier Schottky rectifier: an improved Schottky rectifier with better reverse characteristics

An improved structure of Schottky rectifier,called a trapezoid mesa trench metal-oxide semiconductor (MOS) barrier Schottky rectifier (TM-TMBS),is proposed and studied by two-dimensional numerical simulations.Both forward and especially better reverse I-V characteristics,including lower leakage current and higher breakdown voltage,are demonstrated by comparing our proposed TM-TMBS with a regular trench MOS barrier Schottky rectifier (TMBS) as well as a conventional planar Schottky barrier diode rectifier.Optimized device parameters corresponding to the requirement for high breakdown voltage are given.With optimized parameters,TM-TMBS attains a breakdown voltage of 186 V,which is 6.3% larger than that of the optimized TMBS,and a leakage current of 4.3×10 6 A/cm 2,which is 26% smaller than that of the optimized TMBS.The relationship between optimized breakdown voltage and some device parameters is studied.Explanations and design rules are given according to this relationship.     

The Mott diode as a heterodyne receiver element

This paper considers a novel doping profile for Schottky barrier mixer diodes called the Mott barrier. The structure consists of a metal-semiconductor junction in which the semiconductor's epitaxial layer is very lightly doped and thin enough so that it remains depleted even under substantial forward bias. It has been proposed that Mott barrier diodes will generate less noise and have lower series resistance-junction capacitance products than standard Schottky diodes, thus increasing the sensitivity and cut-off frequency of heterodyne receivers. In this paper, the band structure and electron transport properties of the Mott diode are evaluated. This analysis shows that the Mott diode actually will have a large series resistance-junction capacitance product and excessive hot electron noise, making it a poor candidate for high-frequency applications. Experimental results are presented which substantiate these conclusions.     

Comparison of electrical characteristic between AlN/GaN and AlGaN/GaN heterostructure Schottky diodes

Ni/Au Schottky contacts on AlN/GaN and AlGaN/GaN heterostructures are fabricated.Based on the measured current–voltage and capacitance–voltage curves,the electrical characteristics of AlN/GaN Schottky diode,such as Schottky barrier height,turn-on voltage,reverse breakdown voltage,ideal factor,and the current-transport mechanism,are analyzed and then compared with those of an AlGaN/GaN diode by self-consistently solving Schrdinger’s and Poisson’s equations.It is found that the dislocation-governed tunneling is dominant for both AlN/GaN and AlGaN/GaN Schottky diodes.However,more dislocation defects and a thinner barrier layer for AlN/GaN heterostructure results in a larger tunneling probability,and causes a larger leakage current and lower reverse breakdown voltage,even though the Schottky barrier height of AlN/GaN Schottky diode is calculated to be higher that of an AlGaN/GaN diode.     

A super junction SiGe low-loss fast switching power diode

This paper proposes a novel super junction (SJ) SiGe switching power diode which has a columnar structure of alternating p^- and n^- doped pillar substituting conventional n^- base region and has far thinner strained SiGe p⁺ layer to overcome the drawbacks of existing Si switching power diode. The SJ SiGe diode can achieve low specific on-resistance, high breakdown voltages and fast switching speed. The results indicate that the forward voltage drop of SJ SiGe diode is much lower than that of conventional Si power diode when the operating current densities do not exceed 1000 A/cm², which is very good for getting lower operating loss. The forward voltage drop of the Si diode is 0.66V whereas that of the SJ SiGe diode is only 0.52 V at operating current density of 10 A/cm². The breakdown voltages are 203 V for the former and 235 V for the latter. Compared with the conventional Si power diode, the reverse recovery time of SJ SiGe diode with 20 per cent Ge content is shortened by above a half and the peak reverse current is reduced by over 15%. The SJ SiGe diode can remarkably improve the characteristics of power diode by combining the merits of both SJ structure and SiGe material.     

4H-SiC肖特基二极管的电荷收集特性

针对极端环境下耐辐照半导体核探测器的研制需求,采用耐高温、耐辐照的4H碳化硅(4H-SiC)宽禁带材料制成肖特基二极管,研究了该探测器对241Am源粒子的电荷收集效率。从电容-电压曲线得出该二极管外延层净掺杂数密度为1.991015/cm3。从正向电流-电压曲线获得该二极管肖特基势垒高度为1.66 eV,理想因子为1.07,表明该探测器具备良好的热电子发射特性。在反向偏压高达700 V时,该二极管未击穿,其漏电流仅为21 nA,具有较高的击穿电压。在反向偏压为0~350 V范围内研究了该探测器对3.5 MeV 粒子电荷收集效率,在0 V时为48.7%,在150 V时为99.4%,表明该探测器具有良好的电荷收集特性。     

The effects of annealing on Au/pyronine-B/MD n-InP Schottky structure

Thin film of non-polymeric organic compound pyronine-B has been fabricated on moderately doped (MD) n-InP substrate as an interfacial layer using spin coating technique for the electronic modification of Au/MD n-InP Schottky contact. The electrical characteristics have been determined at room temperature. The barrier height and the ideality factor values for Au/pyronine-B/MD n-InP Schottky diode have been obtained from the forward bias I-V characteristics at room temperature as 0.60 eV and 1.041; 0.571 and 1.253 eV after annealing at 100 and 250 °C, respectively. An increase in annealing temperature at the Au/n-InP Schottky junction is shown to increase the reverse bias leakage current by about one order of magnitude and decrease the Schottky barrier height by 0.027 eV. Furthermore, the barrier height values for the Au/pyronine-B/MD n-InP Schottky diode have also been obtained from the C-V characteristics at room temperature as 1.001 and 0.709 eV after annealing at 100 and 250 °C, respectively. Finally, it was seen that the diode parameters changed with increase in the annealing temperature.     

铝-金刚石界面电子特性与界面肖特基势垒的杂化密度泛函理论HSE06的研究

宽带隙半导体金刚石具有突出的电学与热学特性,近年来,基于金刚石的高频大功率器件受到广泛关注,对于金属-金刚石肖特基结而言,具有较高的击穿电压和较小的串联电阻,所以金属-金刚石这种金半结具有非常好的发展前景.本文通过第一性原理方法去研究金属铝-金刚石界面电子特性与肖特基势垒的高度.界面附近原子轨道的投影态密度的计算表明:金属诱导带隙态会在金刚石一侧产生,并且具有典型的局域化特征,同时可以发现电子电荷转移使得Fermi能级在金刚石一侧有所提升.电子电荷在界面的重新分布促使界面形成新的化学键,使得金属铝-氢化金刚石形成稳定的金半结.特别地,我们通过计算平均静电势的方法得到金属铝-氢化金刚石界面的势垒高度为1.03 eV,该值与金属诱导带隙态唯像模型计算的结果非常接近,也与实验值符合得很好.本文的研究可为金属-金刚石肖特基结二极管的研究奠定理论基础,也可为金刚石基金半结大功率器件的研究提供理论参考.     

复合漏电模型建立及阶梯场板GaN肖特基势垒二极管设计

准垂直GaN肖特基势垒二极管(SBD)因其低成本和高电流传输能力而备受关注.但其主要问题在于无法很好地估计器件的反向特性,从而影响二极管的设计.本文考虑了GaN材料的缺陷以及多种漏电机制,建立了复合漏电模型,对准垂直Ga N SBD的特性进行了模拟,仿真结果与实验结果吻合.基于此所提模型设计出具有高击穿电压的阶梯型场板结构准垂直GaN SBD.根据漏电流、温度和电场在反向电压下的相关性,分析了漏电机制和器件耐压特性,设计的阶梯型场板结构准垂直GaN SBD的Baliga优值BFOM达到73.81 MW/cm~2.