In situ monitoring of reaction-induced phase separation with modulated temperature DSC

A linearly polymerizing and network forming epoxy-amine system, DGEBA-aniline and DGEBA-MDA, respectively, will be modified with 20 wt% and 50 wt% of a high-T_g thermoplastic poly(ether sulphone) (T_g=223°C), respectively, both showing LCST-type demixing behavior. Reaction-induced phase separation (RIPS) in these modified systems is studied using Modulated Temperature DSC (MTDSC) as an in situ tool. Phase separation in the linear system can be probed by vitrification of the PES-rich phase, occurring at a higher conversion than the actual cloud point from light scattering measurements. The negative slope of the cloud point curve in a temperature-conversion-transformation diagram unambiguously shows the LCST-type demixing behavior of this system, while the relation between the composition/glass transition of the PES-rich phase and the cure temperature is responsible for the positive slope of its vitrification line. Phase separation in the network forming system appears as reactivity increases at the cloud point due to the concentration of reactive groups. Different mixture compositions alter the ratio between the rate of phase separation and the rate of reaction, greatly affecting the morphology. Information about this in situ developed structure can be obtained from the heat capacity evolutions in non-isothermal post-cures.     

Phase Behavior in Blends of Ethylene Oxide–Propylene Oxide Copolymer and Poly(ether sulfone) Studied by Modulated-Temperature DSC and NMR Relaxometry

The state diagram of a blend consisting of a copolymer containing ethylene oxide and propylene oxide, P(EO-ran-PO), and poly(ether sulfone), PES, is constructed by using modulated-temperature differential scanning calorimetry (MTDSC), T₂ NMR relaxometry, and light scattering. The apparent heat capacity signal in MTDSC is used for the characterization of polymer miscibility and morphology development. T₂ NMR relaxometry is used to detect the onset of phase separation, which is in good agreement with the onset of phase separation in the apparent heat capacity from MTDSC and the cloud-point temperature as determined from light scattering. The coexistence curve can be constructed from T₂ values at various temperatures by using a few blends with well-chosen compositions. These T₂ values also allow the detection of the boundary between the demixing zones with and without interference of partial vitrification and are in good agreement with stepwise quasi-isothermal MTDSC heat capacity measurements. Important interphases are detected in the heterogeneous P(EO-ran-PO)/PES blends.     

The Application of Modulated Temperature Power Compensation DSC to the Characterisation of Polymer Blends

A modulated temperature power compensated differential scanning calorimeter, MTDSC, has been built from a standard Perkin-Elmer DSC model-2 such that a computer generated voltage has been applied to induce a sinusoidal change in sample temperature superimposed on a linear heating rate. The effect of amplitude of the temperature fluctuation, modulation period and block temperature on the reversibility has been assessed from the Lissajous diagram of heat flow vs. sample temperature. From their reproducibility and symmetry the most effective conditions for operating the MTDSC has been deduced. The specific heat of sapphire has been measured using these operational conditions for comparison with conventional DSC. Phase separated blends of polycarbonate (PC) and polyethylene terephthalate (PET) have been analysed. This revised version was published online in August 2006 with corrections to the Cover Date.     

A Theoretical Approach to Temperature Modulated Power Compensation DSC

The steady state of temperature modulated power compensation DSC has been theoretically investigated for measurements of complex heat capacity, taking accounts of heat capacities of heat paths, heat loss to the environment, and mutual heat exchange between the sample and the reference material. Thermal contact between the sample cell and the cell holder is also taken into accounts. Rigorous and general solutions are obtained. From these solutions application of the technique to heat capacity measurements is discussed. This revised version was published online in August 2006 with corrections to the Cover Date.     

Reaction thermodynamics of amine‐cured epoxy systems: Validation of the enthalpy and heat capacity of reaction as determined by modulated temperature differential scanning calorimetry

The reaction enthalpy and reaction heat capacity of three aromatic epoxy–amine systems have been determined with modulated temperature diffential scanning calorimetry (MTDSC), mostly in quasi‐isothermal conditions, over a wide temperature range (33–140 °C) and for different mixture compositions. The reaction enthalpy is only slightly dependent on the epoxy–amine chemistry, from ?111 to ?98 kJ/mol epoxy functionality. With the model system phenyl glycidyl ether (PGE)+aniline, the reaction enthalpy of the secondary amine–epoxy reaction step is equal to that of the primary amine–epoxy reaction. Group contributions needed to calculate the reaction heat capacity with an additivity approach are evaluated, and a new value of 37.2 J mol^?1 K^?1 for the group N? (H)(C)(CB) is proposed. With this group contribution, the additivity method predicts almost equal values for the reaction heat capacity of both amine–epoxy reaction steps at 298.15 K (Δ_rC_p,prim = 15.7 J mol^?1 K^?1 and Δ_rC_p,sec = 14.6 J mol^?1 K^?1), whereas the experimental value of Δ_rC_p,sec is about three times larger than that of Δ_rC_p,prim at 100 °C. These results are confirmed experimentally for PGE+aniline as a different temperature dependence of both reaction heat capacities. MTDSC therefore is potentially interesting for differentiating between reactive species in an epoxy–amine reaction, a benefit previously assigned to spectroscopic methods only. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 594–608, 2003     

Reaction-induced phase separation in polyethersulfone-modified epoxy-amine systems studied by temperature modulated differential scanning calorimetry

In epoxy-amine systems with a thermoplastic additive, the initially homogeneous reaction mixture can change into a multi-phase morphology as a result of the increase in molecular weight or network formation of the curing matrix. Temperature modulated DSC (TMDSC) allows the real-time monitoring of this reaction-induced phase separation. A linear polymerizing epoxy-amine (DGEBA–aniline) and a network-forming epoxy-amine (DGEBA–methylene dianiline), both with an amorphous engineering thermoplastic additive (polyethersulfone, PES), are used to illustrate the effects of phase separation on the signals of the TMDSC experiment. The non-reversing heat flow gives information about the reaction kinetics. The heat capacity signal also contains information about the reaction mechanism in combination with effects induced by the changing morphology and rheology such as phase separation and vitrification. In quasi-isothermal (partial cure) TMDSC experiments, the compositional changes resulting from the proceeding phase separation are shown by distinct stepwise heat capacity decreases. The heat flow phase signal is a sensitive indication of relaxation phenomena accompanying the effects of phase separation and vitrification. Non-isothermal (post-cure) TMDSC experiments provide additional real-time information on further reaction and phase separation, and on the effect of temperature on phase separation, giving support to an LCST phase diagram. They also allow measurement of the thermal properties of the in situ formed multi-phase materials.     

The Use of Modulated Temperature Programs in Thermal Methods

Temperature modulation has long been used in various aspects of thermal methods. Historically, the principle areas of application have been the determination of kinetic parameters using variants of the temperature jump method and the measurement of heat capacity by AC calorimetry. More recently the introduction of temperature modulation in a variety of techniques has been used in combination with deconvolution algorithms to separate sample responses that are dependent on rate of change of temperature from those principally dependent on temperature. Finally, temperature modulation is important in the new field of micro-thermal analysis. This revised version was published online in July 2006 with corrections to the Cover Date.     

Phase behavior of crystalline blends of poly(tetrafluoroethylene) and of random fluorinated copolymers of tetrafluoroethylene

In the present article, we investigate by differential scanning calorimetry (DSC) the thermal behavior (melting, crystallization, and crystal–crystal transitions) far from equilibrium of blends constituted of two crystalline polymers. In particular, the following blends are examined: PTFE–PFMVE, PTFE–FEP, and FEP–PFMVE where PTFE is poly(tetrafluoroethylene), PFMVE is poly(tetrafluoroethylene‐co‐perfluoromethylvinylether), and FEP is poly(tetrafluoroethylene‐co‐hexafluoropropylene). The two last ones are random tetrafluoroethylene copolymers with small amounts of comonomer. Our results indicate that, under the experimental investigated conditions, the blends containing PTFE do not give cocrystallization on cooling from the melt, although under very rapid crystallization conditions, quenching, the presence of the copolymer would seem to slightly influence PTFE crystallization (lower peak temperatures are observed for the crystalline transitions and the melting with respect to those of the neat homopolymer). The behavior of the FEP–PFMVE blend is completely different; in fact, our results indicate the occurrence of cocrystallization, then miscibility in the crystalline phase, for almost all compositions and all investigated experimental conditions. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 679–689, 1999     

Determination of cell asymmetry in temperature-modulated DSC

The quality of measurement of heat capacity by differential scanning calorimetry (DSC) is based on the symmetry of the twin calorimeters. This symmetry is of particular importance for the temperature-modulated DSC (TMDSC) since positive and negative deviations from symmetry cannot be distinguished in the most popular analysis methods. Three different DSC instruments capable of modulation have been calibrated for asymmetry using standard non-modulated measurements and a simple method is described that avoids potentially large errors when using the reversing heat capacity as the measured quantity. It consists of overcompensating the temperature-dependent asymmetry by increasing the mass of the sample pan.On leave from Toray Industries, Inc., Otsu, Shiga 520, JapanOn leave from Toray Research Center, Inc., Otsu, Shiga 520, JapanThis work was supported by the Division of Materials Research, National Science Foundation, Polymers Program, Grant # DMR 90-00520 and the Division of Materials Sciences, Office of Basic Energy Sciences, U. S. Department of Energy at Oak Ridge National Laboratory, managed by Lockheed Martin Energy Research Corp. for the U. S. Department of Energy, under contract number DE-AC0S-96OR22464. Support for instrumentation came from TA Instruments, Inc. and Mettler-Toledo, Research support was also given by ICI Painls, and Toray Industries, Inc.     

Modulated‐temperature differential scanning calorimetry study of temperature‐induced mixing and demixing in poly(vinylmethylether)/water

The heat capacity or reversing heat flow signal from modulated‐temperature differential scanning calorimetry can be used to measure the onset of phase separation in a poly(vinylmethylether)/water mixture, clearly showing the special type III lower critical solution temperature demixing behavior. Characteristic of this demixing behavior is a three‐phase region, which is detected in the nonreversing heat flow signal. Stepwise quasi‐isothermal measurements through the phase transition show large excess contributions in the (apparent) heat capacity signal, caused by demixing/remixing heat effects on the timescale of the modulation (fast process). These excess contributions and their time‐dependent evolutions (slow process) are useful in understanding the kinetics of phase separation and the morphology (interphase) development. Care has to be taken, however, in interpreting the heat capacity signal derived from the amplitude of the modulated heat flow because nonlinear effects lead to the occurrence of higher harmonics. Therefore, the raw heat flow signal for quasi‐isothermal demixing and remixing measurements is also examined in the time domain. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1824–1836, 2003     

聚乳酸-聚乙二醇单甲醚共混体系的调制DSC分析

采用调制差示扫描量热法(MDSC)研究了聚乳酸(PLA)与聚乙二醇单甲醚(MPEG)共混体系的热性能。研究结果表明,MDSC可有效分辨PLA重结晶和熔融的重叠效应,在测试条件下,PLA的α’-α晶型转变与α晶体的熔融几乎同时进行。随着升温速率的加快和调制周期的延长,当增塑剂的质量分数为15%时,PLA-MPEG共混物分割在不可逆曲线的重结晶焓逐渐升高(最高约28J/g),熔融焓逐渐降低(最低约为3.3J/g);分割在可逆曲线的熔融峰逐渐由多重峰变为单峰,且焓变值逐渐升高(最高约66.1J/g),相应的可逆曲线熔融分割比例达到了95.2%。通过提高升温速率和延长调制周期,可使大部分熔融分割在可逆曲线上,但过快的升温速率和过长的调制周期会导致PLA相转变时的周期数过少,DSC调制功能的分辨率下降,设置测试条件时需综合考虑。     

Temperature Modulated DSC for the Investigation of Polymer Materials: A brief account of recent studies

Temperature modulated differential scanning calorimetry (TMDSC), the most recent development that adds periodic modulation to the conventional DSC, has recently seen a fast growth due to availability of commercial instrumentation. The use of the technique necessitates a total control of all of the experimental parameters. The paper focuses on recent applications to investigate polymers [1].This revised version was published online in November 2005 with corrections to the Cover Date.     

Reversibility of the low‐temperature transitions of polytetrafluoroethylene as revealed by temperature‐modulated differential scanning calorimetry

Temperature‐modulated differential scanning calorimetry reveals distinct differences in the kinetics of the low‐temperature phase transitions of polytetrafluoroethylene. The triclinic to trigonal transition at 292 K is partially reversible as long it is not complete. As soon as the total sample is converted, supercooling is required to nucleate the reversal of the helical untwisting involved in the transition. The trigonal phase can be annealed in the early stages after transformation with a relaxtion time of about 5 minutes. The dependence of the reversing heat capacity on the modulation amplitude, after a metastable equilibrium has been reached, is explained by a non‐linear, time‐independent increase of the heat‐flow rate, perhaps caused by an increased true heat capacity. The order‐disorder‐transition at 303 K from the trigonal to a hexagonal condis phase is completely reversible and time‐independent. It extends to temperatures as low as the transition at 292 K or even lower. Qualitatively, the thermal history and crystallization conditions of polytetrafluoroethylene do not affect the transition kinetics, that is, melt‐crystallized film and as‐polymerized powders show similar transition behaviors, despite largely different crystallinities. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 750–756, 2001     

Thermal properties of single walled carbon nanotube‐silicone nanocomposites

The effect of single walled carbon nanotube (SWCNT) fillers on the low temperature thermal properties and curing behavior of SWCNT‐silicone nanocomposite are reported for the first time. The SWCNT‐silicone composites were prepared by different mixing procedures and characterized by differential scanning calorimetry (DSC). Solution mix, with the aid of sonication and soaking achieved better dispersion of SWCNTs in the silicone. The adding of SWCNTs in polymer seriously hindered the curing of silicone elastomer. The hindrance increased with increasing concentration of SWCNT and the quality of dispersion. The glass transition temperatures (T_g) of the nanocomposites were found to be independent of the SWCNT addition, although, the steps in the heat capacity (Δc_p) of the glass transition were smaller with increasing SWCNTs concentration. The melt crystallization behavior was strongly dependent on the concentration and dispersion of SWCNT in the polymer. The cooling scan showed that the higher concentration and the better dispersion of SWCNTs in the silicone resulted in higher percentage of melt crystallization of this nanocomposite. The correlation of the change of thermal properties to the dispersion of CNT in polymer may be used to determine the quality of SWCNT dispersion in silicone polymer. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1845–1852, 2008     

Heat capacities of a series of terminal linear alkyldiamides determined by DSC

Molar heat capacities of twelve linear alkane-α,ω-diamides H₂NOC-(CH₂)_(n-2)-CONH₂, (n=2 to 12 and n=14) were measured by differential scanning calorimetry at T=183 to 323 K. Heat flow rate calibration of the Mettler DSC 30 calorimeter was carried out by using benzoic acid as reference material. The calibration was checked by determining the molar heat capacity of urea in the same temperature range as that of measurements. The molar heat capacities of alkane-α,ω-diamides increased in function of temperature and fitted into linear equations. Smoothed values of C _p,m at 298.15 K displayed a linear increase with the number of carbon atoms. The C _p,m contribution of CH₂ group was (22.6±0.4) J K⁻¹ mol⁻¹, in agreement with our previous results concerning linear alkane-a,ω-diols and primary alkylamides as well as the literature data on various series of linear alkyl compounds. On leave from the Faculty of Chemistry, University of Craiova, Calea Bucureşti 165, Craiova 1100, Romania     

Isothermal crystallization of concentrated amorphous starch systems measured by modulated differential scanning calorimetry

The slow isothermal crystallization of concentrated amorphous starch systems is measured by Modulated Differential Scanning Calorimetry (MDSC). It can be followed continuously by the evolution (stepwise decrease) of the MDSC heat capacity signal (Cp), as confirmed with data from X-ray diffractometry, Dynamic Mechanical Analysis, Raman spectroscopy, and conventional Differential Scanning Calorimetry. Isothermal MDSC measurements enable a systematic study of the slow crystallization process of a concentrated starch system, such as a pregelatinized waxy corn starch with 24 wt % water and 76 wt % starch. After isothermal crystallization, a broad melting endotherm with a bimodal distribution is observed, starting about 10°C beyond the crystallization temperature. The bulk glass transition temperature (T_g) decreases about 15°C during crystallization. The isothermal crystallization rate goes through a maximum as a function of crystallization time. The maximum rate is characterized by the time at the local extreme in the derivative of Cp (t_max), or by the time to reach half the decrease in Cp (t_1/2). Both t_max and t_1/2 show a bell-shaped curve as a function of crystallization temperature. The temperature of maximum crystallization rate, for the system studied, lies as high as 75°C. This is approximately 65°C above the initial value of T_g. Normalized Cp curves indicate the temperature dependence of the starch crystallization mechanism. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2881–2892, 1999     

Calculation of smoothing factors for the comparison of DSC results

Complex mixtures of long chain organic compounds often show overlapping glass transition temperatures (T _gs) when analyzed by differential scanning calorimetry (DSC) or modulated DSC (MDSC). In such cases, subjective and inconsistent smoothing of data acquired under different conditions can lead to the misinterpretation of results. A quantitative method for the selection of smoothing factors for the analysis and comparison of (M)DSC results is presented. The method is most useful for the analysis of the derivative of the heat capacity, dC _p/dt or dC _p/dT, plots which best highlight overlapping T _gs. Four equations are shown to relate the heating rate and the smoothing factor. The equations allow a comparison of data acquired i) at different heating rates and plotted vs. temperature, ii) at a single heating rate and plotted vs. both time and temperature, i.e., dC _p/dt vs. dC _p/dT, iii) at different heating rates and plotted vs. both time and temperature, and iv) at different heating rates, and shown exclusively in the time domain. Examples of the use of the equations are provided for the analysis of bitumen, a complex mixture of natural origin.     

Structure of Composite Films Containing Polyaniline Studied by DSC

A structural study of conductive composite films consisting of ethylene-co-vinylacetate (EVA) copolymer, polyaniline (PANI) and dodecylbenzenesulfonic acid (DBSA), a part of which being complexed with PANI, was performed by using differential scanning calorimetry (DSC) and presented for the first time. An additional crystalline phase is formed during the film formation by thickening EVA chain-folded lamellae with participation of‘free’ DBSA molecules at lower net PANI content (up to 5 mass%) and of both ‘free’ and complexed DBSA molecules (up to 7.5 mass%). At higher PANI content PANI-DBSA complex starts to form its own crystals and at 17.5 mass% of PANI mixed crystals of EVA with ‘free’ DBSA alkyl chains are preferably formed. It is also found that the Fox' equation correlating the glass transition temperature of a miscible blend system with its composition can be actually used in estimating the miscibility of EVA/PANI blends no matter the presence of DBSA. This revised version was published online in August 2006 with corrections to the Cover Date.     

用DSC直接法测量POM晶体的比热容

比热容是物质的特性参数之一。测定比热容的经典方法通常是采用各种类型的精密量热计,该方法测量精度高,但操作繁琐,费时费力。采用差示扫描量热法(DSC)测定比热容精度可达到0.3%,具有速度快、试样用量少等优点。 本文用DSC法测量人工晶体3-甲基-4-硝基氧化吡啶(POM)在320～380K之间的比热容,以往尚无文献报道。     

A Modulated Differential Scanning Calorimetric study

Modulated Differential Scanning Calorimetry^? has been applied to frozen sucrose solutions in the concentration range 10–80% w/w. The results from this study present, for the first time, information on the reversing and non-reversing nature of events that occur in these solutions. The study demonstrates the potential benefits of this new technique to help separate complex transitions that can occur in the total heat-flow curves obtained using traditional differential scanning calorimetry. The results illustrate how this new technique can separate the different enthalpic events, which relate to the glass transition and the onset of ice dissolution that occurs during the heating of these frozen systems, by nature of their “reversing” and “non-reversing” contributions to the total heat flow.