Separation of nicotine metabolites by capillary zone electrophoresis and capillary zone electrophoresis/mass spectrometry

The use of capillary zone electrophoresis (CZE) and capillary zone electrophoresis/mass spectrometry (CZE/MS) has been demonstrated, in principle, for the separation of nicotine and nicotine metabolites. The buffer system developed for separation and detection by CZE/UV was modified for use in CZE/MS analysis. Several of the metabolites are isobaric and tandem mass spectrometric (MS/MS) techniques have been used to differentiate such analytes.     

Arsenic speciation by coupling capillary zone electrophoresis with mass spectrometry

Summary Capillary zone electrophoresis (CZE) has been coupled with mass spectrometry to enable the identification of mineral and organometallic compounds of arsenic in speciation studies. The electrophoretic effluent was introduced through a concentric interface into the mass spectrometer. Make-up liquid was added to enable electric contact at the outlet of the separation capillary and to assist the electronebulization process. After ionization, the ions were analyzed and quantified with an ion-trap detector. Optimization of the coupling conditions (geometry of the concentric interface, composition and flow rate of the sheath liquid, electronebulization and detection conditions) is described. The results show that the geometry of the concentric interface and the positioning of the outlet of the separation capillary have a critical effect on stability and sensitivity. Programming the electronebulization and detection conditions throughout the analysis enabled identification and quantification of the seven arsenic compounds of interest (neutral, and positively or negatively charged species) in less than 20 min at the ppm level. Limits of detection ranged from 0.5 to 3.3 mg L⁻¹, corresponding to amounts injected ranging from 15 to 60 pg. The linear dependence of mass spectrometric response on arsenic concentration was verified for concentrations ranging from 5 to 200 mgL⁻¹. For the two positively charged species, arsenobetaine and arsenocholine, an on-line preconcentration technique (field-amplified sample injection) enabled reduction of the detection limits by approximately one order of magnitude to 110 and 160 μgL⁻¹, respectively.     

Characterization of deamidated peptide variants by micro-preparative capillary electrophoresis and mass spectrometry

Capillary electrophoresis (CE) was compared with reversed-phase liquid chromatography for its ability to separate native and deamidated peptides. CE is shown to provide superior resolution of these peptides due to its charge-based separation mechanism. Fraction collection performed using a standard CE instrument equipped with a 96-well plate permits subsequent characterization by nanospray mass spectrometric (MS) analysis. Additional in-depth analysis by MS/MS is able to provide the location of the deamidation site based on y-ion mass shifts of 1 Da.     

Separation and identification of platinum adducts with DNA nucleotides by capillary zone electrophoresis and capillary zone electrophoresis coupled to mass spectrometry

Platinum adducts are supposed to be the cytotoxic lesions in DNA after platinum-containing anticancer therapy. Various adducts are formed upon interaction of platinum complexes with nucleotides, but contribution of individual adducts to antitumor activity and toxicity of platinum complexes still remains to be examined. A capillary zone electrophoresis (CZE) method is described that is suitable to separate individual platinum adducts. We investigated the formation of adducts following the reaction of cis-diamminedichloroplatinum (II) (cisplatin) with various DNA nucleotides. Baseline separation of unmodified and modified nucleotides (adducts) was achieved using uncoated fused-silica capillaries and basic separation buffers. In order to elucidate the observed peak pattern, a coupled CZE-electrospray ionization-mass spectrometry (ESI)-MS approach was applied. After incubation of mononucleotides with cisplatin, monochloro, monoaqua and bifunctional adduct species were detected. Consequently, the migration order of nucleotides and individual platinum adducts could be determined. Moreover, the time-dependent conversion from monochloro to monoaqua and subsequently to bifunctional adducts was monitored. In conclusion, individual platinum adducts were separated by CZE and identified by CZE-ESI-MS. Formation and conversion of distinct species were confirmed. Potential applications comprise studies of novel platinum complexes, investigations of platinum-adduct formation with DNA, and determination of platinum-DNA adducts in cells.     

Capillaries modified by noncovalent anionic polymer adsorption for capillary zone electrophoresis, micellar electrokinetic capillary chromatography and capillary electrophoresis mass spectrometry

A simple coating procedure for generation of a high and pH-independent electroosmotic flow in capillary zone electrophoresis (CZE) and micellar electrokinetic capillary chromatography (MEKC) is described. The bilayer coating was formed by noncovalent adsorption of the ionic polymers Polybrene and poly(vinylsulfonate) (PVS). A stable dynamic coating was formed when PVS was added to the background electrolyte. Thus, when the PVS concentration in the background electrolyte was optimized for CZE (0.01%), the EOF differed less than 0.3% after 54 runs. The electroosmotic mobility in the coated capillaries was (4.9+/-0.1) x 10(-4) cm2V(-1)s(-1) in a pH-range of 2-10 (ionic strength = 30 mM). When alkaline compounds were used as test substances intracapillary and intercapillary migration time variations (n = 6) were less than 1% relative standard deviation (RSD) and 2% RSD, respectively in the entire pH range. The coating was fairly stable in the presence of sodium dodecyl sulfate, and this made it possible to perform fast MEKC separations at low pH. When neutral compounds were used as test substances, the intracapillary migration time variations (n = 6) were less than 2% RSD in a pH range of 2-9. In addition to fast CZE and MEKC separations at low pH, analysis of the alkaline compounds by CE-MS was also possible.     

Artificial neural network modeling of peptide mobility and peptide mapping in capillary zone electrophoresis

Recently, we have developed an artificial neural network model, which was able to predict accurately the electrophoretic mobilities of relatively small peptides. To examine the robustness of this methodology, a 3-3-1 back-propagation artificial neural network (BP-ANN) model was developed using the same inputs as the previous model, which were the Offord's charge over mass term (Q/M(2/3)), corrected steric substituent constant (E(s,c)) and molar refractivity (MR). The data set consisted of 102 peptides with a larger range of size than that of our earlier report - up to 42 amino acid residues as compared to 13 amino acids in the initial study - that also included highly charged and hydrophobic peptides. The entire data set was obtained from the published result by Janini and co-workers. The results of this model are compared with those obtained using multiple linear regressions (MLR) model developed in this work and the multi-variable model released by Janini et al. Better predictive ability of the BP-ANN model over the MLR indicates the non-linear characteristics of the electrophoretic mobility of peptides. The present model exhibits better robustness than the MLR models in predicting CZE mobilities of a diverse data set at different experimental conditions. To explore the utility of the ANN model in simulation of the CZE peptide maps, the profiles for the endoproteinase digests of melittin, glucagon and horse cytochrome C is studied in the present work.     

Indirect fluorometric detection of tryptic digests separated by capillary zone electrophoresis

This work demonstrates the analytical utility of indirect fluorescence detection with capillary zone electrophoresis (CZE) for the analysis of trace quantities of macromolecular mixtures. Detection is based upon charge displacement and is not based upon any absorption or emission property of the analyte. No derivatization step is required. Indirect fluorescence is therefore a general detector for electrophoresis. Subfemtomolar quantities of tryptic digest mixtures are separated within three minutes, and reproducible peaks are obtained from the mixtures. Mass limits of detection are 3000 times lower than those of commercial high-performance liquid chromatography (HPLC) UV absorbance detectors and 180 times lower than those of UV absorbance detectors in CZE systems. This separation and detection system should be well suited to analysis of trace quantities of mixtures of peptides.     

Analysis of microcystins by capillary zone electrophoresis coupling with electrospray ionization mass spectrometry

In this paper, a rapid and effective method based on capillary zone electrophoresis (CZE) coupled with electrospray ionization mass spectrometry (ESI-MS) was established for the trace analysis of microcystin (MC) isomers in crude algae sample. The experimental conditions including the composition, acidity and concentration of buffer, separation voltage, injection time, and MS detection parameters were investigated in detail. A capillary separation system was as follows: a uncoated fused-silica capillary tube (50 μm i.d. × 90 cm), 40 mmol L⁻¹ ammonium acetate solution (pH 9.86) as running buffer, 25 kV as separation voltage, 20 kV × 3 s water first and 20 kV × 20 s for sample injection. Mass analysis was performed in ESI source, with sheath gas temperature 150 °C, sheath gas pressure 10 psi, and sheath gas flow 6 L min⁻¹. And sheath liquid was 7.5 mmol L⁻¹ acetic acid in 50% isopropanol-water (3 μL min⁻¹). Protonation and ammonium adduct molecular ions m/z 506.9 (MC-LR) and 532.0 (MC-YR) were used for the quantification of MCs. Under these conditions, two MCs were baseline separated within 9 min, the calibration curves were obtained in the range of 0.11-10.0 μg mL⁻¹ and 0.16-10.5 μg mL⁻¹ for MC-LR and MC-YR, respectively. Meanwhile, limits of detection were 0.05 and 0.08 μg mL⁻¹ for MC-LR and MC-YR, respectively. The recoveries for the two MCs were in the range of 95.8-108%. The developed approach had been successfully applied to the analysis of MCs in crude algae samples.     

Qualitative determination of urinary morphine by capillary zone electrophoresis and ion trap mass spectrometry

A rapid, sensitive method for the determination of morphine and amphetamine was developed using capillary zone electrophoresis coupled with electrospray interface (ESI), ion-trap tandem mass spectrometry (CE-ESI-MS2). Morphine and amphetamine were separated in 20 mM ammonium acetate buffer (pH 6.6) and detected by ion-trap mass detector in different analytical time segments (0-6.25 min for amphetamine and 6.25-12.0 min for morphine) in which the tune file for each compound was used separately. Molecular ions of morphine (m/z 286) and amphetamine (m/z 136) were detected at 5.77 and 6.83 min, respectively, while product ions of MS2 for each compound (m/z 229, 201 for morphine and m/z 119 for amphetamine) were detected almost exactly at the same time with their parent compounds. The limits of detection (LOD) for MS2 determination were 30 and 50 ng/mL for amphetamine and morphine, respectively, with an S/N ratio of 3. For more sensitive detection of morphine, the sample was injected for a longer time (i.e., 80 s) and hydrodynamically transported into a CE capillary for MS detection. Morphine and its product ion appear at 0.36 and 0.39 min on the ion chromatogram, respectively, with a five-fold increase of detection sensitivity (LOD, 10 ng/mL). The CE-MS system thus established was further applied for forensic urine samples screened as morphine-positive by fluorescence polarization immunoassay (FPIA). These results indicated the feasibility of CE-ESI-MS2 for confirmative testing of morphine in urine sample.     

Determination of tobacco-specific N-nitrosamines in rabbit serum by capillary zone electrophoresis and capillary electrophoresis-electrospray ionization-mass spectrometry with solid-phase extraction

In this paper, we propose a new strategy for separation and determination of tobacco-specific N-nitrosamines (TSNAs), a group of strong carcinogens found only in tobacco products, by using CZE and CE-MS associated with SPE. Six TSNAs: N'-nitrosonornicotine, N'-nitrosoanatabine, N'-nitrosoanabasine, 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanone, 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanol, and 4-(methylnitrosamino)-4-(3-pyridyl)-1-butanol were simultaneously separated by either of two CZE methods, one of which worked with ammonium formate buffer (pH 2.5) and another with citrate buffer (pH 2.4), as well as a CE-MS method. The CZE conditions including pH and concentration of running buffer, capillary length, applied voltage, and capillary temperature were systematically optimized. For CE-MS method, an optimized sheath liquid consisted of methanol-water was used at a flow rate of 10 muL/min. With SPE procedure, our proposed CE-MS method was successfully applied to determine TSNAs after 15 min metabolism in rabbits. A comparison study between CZE and CE-MS methods for quantitative purposes was carried out, showing that both methods provided similar separation efficiency, selectivity, repeatability, linearity, and recovery. However, CE-MS method was better suited for the analysis of TSNAs in complicated biological samples for its sensitivity and extra information on molecular structure. Having good accordance with our previous work by using LC-MS, the new CE-MS method is expected to be an alternative to the LC-MS method and applied to study the metabolism of TSNAs.     

Drug impurity profiling by capillary electrophoresis/mass spectrometry using various ionization techniques

Capillary electrophoresis/mass spectrometry (CE/MS) is predominantly carried out using electrospray ionization (ESI). Recently, atmospheric pressure chemical ionization (APCI) and atmospheric pressure photoionization (APPI) have become available for CE/MS. With the VUV lamp turned off, the APPI source may also be used for CE/MS by thermospray ionization (TSI). In the present study the suitability of ESI, APCI, APPI and TSI for drug impurity profiling by CE/MS in the positive ion mode is evaluated. The drugs carbachol, lidocaine and proguanil and their potential impurities were used as test compounds, representing different molecular polarities. A background electrolyte of 100 mM acetic acid (pH 4.5) provided baseline separation of nearly all impurities from the respective drugs. APPI yielded both even‐ and odd‐electron ions, whereas the other ionization techniques produced even‐electron ions only. In‐source fragmentation was more pronounced with APCI and APPI than with ESI and TSI, which was most obvious for proguanil and its impurities. In general, ESI and TSI appeared the most efficient ionization techniques for impurities that are charged in solution achieving detection limits of 100 ng/mL (full‐scan mode). APPI and APCI showed a lower efficiency, but allowed ionization of low and high polarity analytes, although quaternary ammonium compounds (e.g. carbachol) could not be detected. Largely neutral compounds, such as the lidocaine impurity 2,6‐dimethylaniline, could not be detected by TSI, and yielded similar detection limits (500 ng/mL) for ESI, APPI and APCI. In many cases, impurity detection at the 0.1% (w/w) level was possible when 1 mg/mL of parent drug was injected with at least one of the CE/MS systems. Overall, the tested CE/MS systems provide complementary information as illustrated by the detection and identification of an unknown impurity in carbachol. Copyright © 2009 John Wiley & Sons, Ltd.     

Machine learning techniques for the prediction of the peptide mobility in capillary zone electrophoresis

Three machine learning techniques including back propagation artificial neural network (BP-ANN), radial basis function artificial neural network (RBF-ANN) and support vector regression (SVR) were applied to predicting the peptide mobility in capillary zone electrophoresis through the development of quantitative structure-mobility relationship (QSMR) models. A data set containing 102 peptides with a large range of size, charge and hydrophobicity was used as a typical study. The optimal modeling parameters of the models were determined by grid-searching approach using 10-fold cross-validation. The predicted results were compared with that obtained by the multiple linear regression (MLR) method. The results showed that the relative standard errors (R.S.E.) of the developed models for the test set obtained by MLR, BP-ANN, RBF-ANN and SVR were 11.21%, 7.47%, 5.79% and 5.75%, respectively, while the R.S.E.s for the external validation set were 11.18%, 7.87%, 7.54% and 7.18%, respectively. The better generalization ability of the QSMR models developed by machine learning techniques over MLR was exactly presented. It was shown that the machine learning techniques were effective for developing the accurate and relaible QSMR models.     

Optimization of capillary zone electrophoresis/electrospray ionization parameters for the mass spectrometry and tandem mass spectrometry analysis of peptides

The solution chemistry conditions necessary for optimum analysis of peptides by capillary zone electrophoresis (CZE)/electrospray ionization mass spectrometry and CZE electrospray ionization tandem mass spectrometry have been studied. To maximize the signal-to-noise ratio of the spectra it was found necessary to use acidic CZE buffers of low ionic strength. This not only increases the total ion current, but it also serves to fully protonate the peptides, minimizing the distribution of ion current across the ensemble of possible charge states. The use of acidic buffers protonates the peptides, which is advantageous for mass spectrometry and tandem mass spectrometry analysis, but is problematic with CZE when bare fused silica CZE columns are used. These conditions produce positively charged peptides, and negatively charged silanol moieties on the column wall, inducing adsorption of the positively charged peptides, thus causing zone broadening and a loss in separation efficiency. This problem was circumvented by the preparation of chemically modified CZE columns, which, when used with acidic CZE buffers, will have a positively charged inner column wall. The electrostatic repulsion between the positively charged peptides and the positively charged CZE column wall minimizes adsorption problems and facilitates high efficiency separations. Full-scan mass spectra were acquired from injections of as little as 160 fmols of test peptides, with CZE separation efficiencies of up to 250,000 theoretical plates.     

On-line system for peptide mapping by capillary electrophoresis at sub-micromolar concentrations

Peptide mapping has been widely used for the identification of modified proteins involved in certain diseases. Despite the fact that capillary electrophoresis (CE) has been shown to be a powerful tool for the separation and detection of tryptic peptide fragments after protein digestion, this technique lacks sensitivity for mapping proteins isolated in very small quantities from biological samples. Consequently, it has been necessary to preconcentrate the protein before adding the proteolytic enzyme for digestion in solution. These experimental steps are quite long, labor intensive and require a lot of sample handling. In this paper, we describe an on-line system allowing digestion of the protein, followed by preconcentration, separation and detection of the tryptic fragments in 4 h. Up to an 800-fold preconcentration factor was achieved for cytochrome c, despite a loss of separation efficiency induced by the multiple-valve design of the system and dispersion of the 60-nl desorption plug. Moreover, our system showed good migration time reproducibility between peptide maps and could be reused for several samples.     

Capillary electrophoresis-mass spectrometry methods for tryptic peptide mapping of therapeutic antibodies

Tryptic peptide mapping is routinely used in the biotech industry to confirm primary sequence, cell line stability, and to analyze posttranslational modifications. Peptide analysis is generally done by reverse phase liquid chromatography with UV or mass spectrometric detection. This method provides excellent resolution and sequence coverage. However, traditional methods are slow, and generally cannot detect small, hydrophilic peptides due to coelution with the column void volume. In this work, complementary CE-MS peptide analysis methods have been developed. The analyses are performed on a traditional CE-MS instrument with a sheath interface, and also on a novel sheathless interface that promises improved resolution and limit of detection. The methods were performed on a tryptic digest of a therapeutic monoclonal antibody for which LC-MS detects 97% sequence coverage. The 3% not covered consists of 11 peptides containing three amino acids or fewer, including two in the critical complementarity binding domain. Without further processing, the same tryptic digest was analyzed by CE-MS. Separation and detection of the 11 small peptides was achieved on CE-MS systems with both interfaces. The sheathless system produced better peak capacity and gave mass spectra with significantly less noise, while the sheath system proved to have better repeatability.     

An integral probe for capillary zone electrophoresis/continuous-flow fast atom bombardment mass spectrometry

An integral probe for capillary zone electrophoresis/continuous-flow fast atom bombardment mass spectrometry was constructed and operated in either the coaxial or liquid-junction interface mode. Results using these interfaces for the analyses of synthetic peptides are presented. The coaxial arrangement attains the best electrophoretic performance, generally providing a greater number of theoretical plates. However, in that the electrophoresis times are generally greater for the liquid-junction interface because there is no mechanical flow resulting from the source vacuum, the overall separation efficiency of the liquid-junction interface is equal to or greater than that of the coaxial interface. In addition, the liquid-junction interface is easier to set up and operate, and allows larger inner diameter capillaries to be used to achieve higher sample loads.     

Separation of human fibrinopeptides by capillary zone electrophoresis

We describe a method for the simultaneous determination of the five fibrinopeptide forms derived from the thrombin-promoted activation of human fibrinogen by capillary zone electrophoresis (CZE). The fibrinopeptide mixture was first desalted by a solid-phase extraction (SPE) step. The analysis was performed in reversed polarity in a highly cross-linked polyethylene glycol (PEG)-coated capillary with UV-light absorption detection at 200 nm. Several parameters including buffer concentration and pH, presence of an organic modifier, temperature, and applied voltage, have been tested. The best separations were obtained within 20 min, utilizing a 20 mM sodium phosphate buffer without organic modifier, in the narrow 6.1-6.2 pH range, at 25 degrees C, with an applied voltage of 20 kV. Quantitative analysis is made possible by the use of sheep fibrinopeptide A as an internal standard to correct for both extraction and injection errors.