具有高阻抗本征SnO2过渡层的CdS/CdTe多晶薄膜太阳电池

采用超声喷雾热解法制备了具有高阻抗的本征SnO2透明导电膜,将其运用在CdS层减薄了的CdS/CdTe多晶薄膜太阳电池中,对减薄后的CdS薄膜进行了XRD,AFM图谱分析,并对电池进行了光、暗I-V,光谱响应和C-V测试.结果表明,在高阻膜上沉积的减薄CdS薄膜(111)取向更明显,但易形成微孔.引入高阻层后,能消除CdS微孔形成的微小漏电通道,有效保护p-n结,改善了电池的并联电阻、填充因子和短波响应,使载流子浓度增加,暗饱和电流密度减小,从而电池性能得到改善,电池转换效率增加了14.4%.     

图谱分析退火对本征SnO2多晶薄膜性能的影响

提高CdTe太阳电池转换效率的有效途径之一是适当减薄CdS窗口层,减薄了的CdS层会严重影响电池性能,解决方法是在窗口层和透明导电膜之间加一层高阻本征SnO2薄膜。采用反应磁控溅射制备了具有高阻抗的本征SnO2薄膜,并对其进行了后处理,利用XRD,XPS等方法研究了退火前后薄膜的结构,成分及表面化学状态的变化。结果表明:经N2/O2=4:1气氛550℃(0.5h)退火后,样品由非晶态转变为四方相结构的多晶薄膜,具有(110)择优取向;XPS分析表明退火后薄膜的氧含量增加、O(1s)峰向低能方向移动,SnO被氧化成SnO2,使得薄膜的透过率增大,退火后的本征SnO2高阻膜非常适合作为过渡层应用于CdTe太阳电池中。     

ZnS/CdS复合窗口层对CdTe太阳能电池短波光谱响应的影响

采用磁控溅射法制备了ZnS/CdS复合窗口层,并将其应用于CdTe太阳能电池。对所制备薄膜的形貌和结构等进行了研究。测试了具有不同窗口层的CdTe太阳电池的量子效率和光Ⅰ-Ⅴ特性,分析了ZnS薄膜制备条件对CdTe电池器件性能影响;研究了CdS薄膜厚度和ZnS/CdS复合窗口层对短波区透过率以及CdTe太阳电池的光谱响应的影响。着重研究了具有ZnS/CdS复合窗口层的CdTe太阳电池的短波光谱响应。结果表明,CdS窗口层厚度从100 nm减至50 nm后,其对短波区光子透过率平均提高了18.3%,CdTe太阳电池短波区光谱响应平均提高了27.6%。衬底温度250 ℃条件下制备的ZnS晶粒尺寸小于室温下制备的ZnS。具有ZnS/CdS复合窗口层的CdTe电池中,采用衬底温度250 ℃沉积ZnS薄膜来制备窗口层的电池器件,其性能要优于室温下沉积ZnS制备窗口层的电池器件。这说明晶粒尺寸的大小对电子输运有一定影响。在相同厚度CdS的前提下,具有ZnS/CdS复合窗口层的CdTe电池比具有CdS窗口层在短波的光谱响应提高了约2%。这说明ZnS/CdS复合窗口层能够做到减少对短波光子的吸收,从而使更多的光子被CdTe电池的吸收层吸收。     

氧对于在Ar/O氛围下用近空间升华法制备的CdS薄膜的影响

采用近空间升华法（CSS）在氩/氧气氛中制备了硫化镉（CdS）多晶薄膜.利用XRD,XPS,AFM,UV-VIS光谱和四探针技术等测试和分析手段系统研究了氧对薄膜的成分、结构、光学和电学等性质的影响.结果表明,用近空间升华法制备的CdS薄膜具有六方相结构,膜层致密、均匀,平均晶粒大小约为40 nm,富硫.氧掺入后部分与镉生成氧化镉,并随着氧含量的增加,薄膜的成分有趋于化学计量比的趋势,光学带隙加宽,光暗电导比增加.此外,还利用扫描电镜（SEM）观察了CdS/CdTe断面结合光谱响应（QE）的结果讨论了氧对CdS/CdTe界面互扩散的影响.发现,随着CdS薄膜制备气氛中氧分压的升高,CdS/CdTe界面的互扩散程度降低,有利于提高器件在500—600 nm波长范围内的光谱响应.认为,氧含量的增加不但使CdS薄膜在光伏应用方面的质量得到改善,而且CdTe太阳电池器件中的CdS/CdTe界面也得到了优化. 关键词： CdS多晶薄膜 近空间升华法 窗口层 界面     

化学水浴法制备大面积CdS薄膜及其光伏应用

采用化学水浴法制备了大面积CdS多晶薄膜,研究了薄膜的形貌、结构和光学性质,结果表明,大面积CdS多晶薄膜具有良好的均匀性,通过优化CdS多晶薄膜,制成了不同CdS窗口层厚度的CdTe小面积太阳电池,减薄CdS薄膜可有效提高器件的短路电流,改善器件性能.随后,在面积30cm×40cm的衬底上制备了全面积为993.6cm²的CdTe太阳电池组件,其27个集成单元的电学性质较为均匀,太阳电池组件的光电转换效率8.13%. 关键词： 化学水浴法(CBD) CdS薄膜 CdTe太阳电池 CdTe太阳电池组件     

CdTe太阳电池前电极SnO2:F/SnO2复合薄膜性能分析

减薄CdS窗口层是提高CdS/CdTe太阳电池转换效率的有效途径之一,减薄窗口层会对器件造成不利的影响,因此在减薄了的窗口层与前电极之间引入过渡层非常必要.利用反应磁控溅射法在前电极SnO₂:F薄膜衬底上制备未掺杂的SnO₂薄膜形成过渡层,并将其在N₂/O₂=4 ∶1,550 ℃环境进行了30 min热处理,利用原子力显微镜、X射线衍射仪、紫外分光光度计对复合薄膜热处理前后的形貌、结构、光学性能进行了表征,同时分析了复     

不同温度下制备的CdTe薄膜对太阳电池光电性能的影响

在不同温度下用近空间升华法（CSS）制备了CdTe多晶薄膜,结合I-V,C-V特性及深能级瞬态谱研究了不同温度制备的CdTe薄膜对CdS/CdTe太阳电池性能的影响.结果表明,制备温度对电池组件的开路电压影响不大,对短路电流和填充因子有影响,CdTe薄膜的深中心对温度和频率的响应基本一致.580℃制备的样品暗饱和电流密度最小,载流子浓度较高,光电特性较好,而且空穴陷阱浓度较低,深中心复合作用较小.在此研究基础上制备出了面积为300 mm×400 mm 关键词： 制备温度 CdTe薄膜 深能级瞬态谱（DLTS） CdS/CdTe太阳电池     

肖特基势垒对CdS/CdTe薄膜电池J-V暗性能的影响

采用数学模拟方法分析了不同背接触势垒高度(φ_b) 对于CdS/CdTe薄膜电池的J-V(电流密度-电压)方程的影响, 得出了势垒高度与roll-over的变化对应关系. 采用相应Cu/Mo背电极的CdS/CdTe薄膜电池在220-300 K的变温J-V曲线的数值分析与理论分析相对照, 分析了背势垒对于J-V曲线拟合参数的影响. 修正了φ_b 与反向饱和电流(J_b0)关系式, 理论与实验符合得非常好. 关键词： CdS/CdTe薄膜 伏安特性 肖特基势垒 roll-over     

碲化镉薄膜太阳电池中的关键科学问题研究

文章对CdTe薄膜太阳电池中的4个关键科学问题进行了讨论,并对电池器件的性能进行了研究,其中包括高质量硫化镉薄膜、背接触层、CdS/CdTe界面和CdCl2热处理性能的研究.文章作者研究了背电极接触层中Cu掺杂含量对电池性能的影响,通过改变背接触层中Cu的含量,可以改变Cu与Te反应产生的物相成分,从而发现以Cu1.4Te为主导的背接触缓冲层能有效地减少电池I—V曲线中的“翻转”(roll-over)现象,同时能有效地降低背接触势垒.此外,还研究了CdS/CdTe界面的CdCl2热处理反应,发现当热处理温度高于350℃时,CdS与CdTe之间的互扩散开始发生,此温度对应于CdS由立方相转变为六方相;而在550℃热处理后,S和Te互扩散形成的CdSxTe1-x化合物,其x值高达11％.通过优化电池制备工艺,获得了在AMl.5标准光源下高达14.6％的CdTe电池转换效率.     

磁控溅射Cl掺杂CdTe薄膜的孪晶结构与电学性质

CdTe用作薄膜太阳能电池吸收层需要经过氯处理才能得到高的光电转换效率,其中Cl原子的作用机理仍然没有完全被理解.实验发现Cl原子主要偏聚在CdTe晶界处,对晶界有钝化作用,而有第一性原理计算认为Cl原子掺入CdTe晶格能够引入浅能级提高光电转换效率.为了验证Cl原子掺杂是否对CdTe的光电转换效率有益,本文通过磁控溅射制备了100 ppm(ppm=1/1000000)Cl原子掺杂的CdTe(CdTe:Cl)薄膜并研究了薄膜的晶体结构与电学性质,同时对比了正常氯处理的无掺杂CdTe薄膜与CdTe:Cl薄膜之间的性质区别.实验发现Cl原子掺杂会在CdTe:Cl中形成大量仅由几个原子层构成的孪晶,电子和空穴在CdTe:Cl薄膜中没有分离的传导通道,而在氯处理后的CdTe薄膜中电子沿晶界传导,空穴沿晶粒内部传导.磁控溅射沉积的CdTe:Cl多晶薄膜属于高阻材料,退火前载流子迁移率很低,退火后载流子浓度降低到本征数量级,电阻率提高.CdTe:Cl薄膜电池效率远低于正常氯处理的无掺杂CdTe薄膜电池效率.磁控溅射制备的非平衡重掺杂CdTe:Cl多晶薄膜不适合用作薄膜太阳能电池的吸收层.     

连续离子层吸附反应沉积后硫化法制备柔性铜锌锡硫薄膜太阳电池

在柔性钼箔衬底上采用连续离子层吸附反应法(successive ionic layer absorption and reaction)制备ZnS/Cu2SnSx叠层结构的预制层薄膜,预制层薄膜在蒸发硫气氛、550 C温度条件下进行退火得到Cu2ZnSnS4吸收层.分别采用EDS,XRD,Raman,SEM表征吸收层薄膜的成分、物相和表面形貌.结果表明,退火后薄膜结晶质量良好,表面形貌致密.用在普通钠钙玻璃上采用相同工艺制备的CZTS薄膜表征薄膜的光学和电学性能,表明退火后薄膜带隙宽度为1.49 eV,在可见光区光吸收系数大于104cm 1,载流子浓度与电阻率均满足薄膜太阳电池器件对吸收层的要求.用上述柔性衬底上的吸收层制备Mo foil/CZTS/CdS/i-ZnO/ZnO:Al/Ag结构的薄膜太阳电池得到2.42%的效率,是目前报道柔性CZTS太阳电池最高效率.     

Growth of nanocrystalline CuIn3Se5 (OVC) thin films by ion exchange reactions at room temperature and their characterization as photo-absorbing layers

Nanocrystalline CuIn₃Se₅ thin films have been grown on ITO glass substrates using chemical ion exchange reactions with CdS, in alkaline medium at pH 11. The as-deposited films were annealed in air at 200 °C for 30 min and characterized using X-ray diffraction (XRD), transmission electron microscopy, energy dispersive X-ray analysis, X-ray photoelectron spectroscopy, and scanning electron microscopy to study the structural, compositional and morphological properties. The XRD patterns reveal the nanoparticles size to be of 18-20 nm diameter, while from the SEM images the nanoparticles size is estimated to be 20-30 nm. It is observed that the annealed films contain nanocrystallites connected with each other through grain boundaries, with grain size of about 100-125 nm and have an overall n-type electrical conductivity and higher photoconductivity. The current-voltage (I-V) characteristics (in dark and light) of these films indicated the formation of a Schottky like junction between the n-CuIn₃Se₅ (OVC) and CdS/ITO layers.     

2-2型磁电复合薄膜CoFe2O4/Pb(Zr0.53Ti0.47)O3静磁耦合

运用溶胶-凝胶法在Pt/Ti/SiO₂/Si基片上旋涂制备了2-2型CoFe₂O₄/Pb(Zr_0.53Ti_0.47)O₃磁电复合薄膜．制备的磁电薄膜结构为基片/PZT/CFO/PZT*/CFO/PZT,通过改变中间层PZT*溶胶的浓度,改变磁性层间距以及静磁耦合的大小．SEM结果表明,复合薄膜结构致密,呈现出界面清晰平整的多层结构．制备的复合薄膜具有较好的铁电与铁磁性能．实验还研究了静磁耦合对薄膜磁电性能的影响,结果表明,随着复合薄膜磁性层间距的减小,静磁耦合效应的增加,磁电电压系数有逐渐增大的趋势.     

A comparative study of thin films of Zn(O;OH)S and In(O;OH)S deposited on CuInS2 by chemical bath deposition method

In this work, a study of synthesis of thin films of Zn(O;OH)S and In(O;OH)S deposited by chemical bath deposition (CBD) is presented. The thin films of Zn(O;OH)S and In(O;OH)S were deposited from different chemical bath systems on absorber layers of CuInS₂ (CIS), indium tin oxide substrates (ITO) and soda lime glass substrates (SL). The differences on the growth rate, optical, morphological and structural properties of the thin films Zn(O;OH)S and In(O;OH)S are studied. The Growth studies showed that thin films of Zn(O;OH)S and In(O;OH)S grown faster on CIS than on SL and ITO substrates. The optical and morphological studies showed that both thin films present high transmittance in visible electromagnetic spectrum and covered uniformly the surface of the substrate, furthermore it was observed that thin films of Zn(O;OH)S and In(O;OH)S were polycrystalline. Finally, the results suggest that thin films of Zn(O;OH)S and In(O;OH)S obtained in this work could be used as buffer layer to replace the thin films of CdS, which are conventionally used as buffer layer in chalcopyrite based solar cells.     

Synthesis of SnS thin films via galvanostatic electrodeposition and fabrication of CdS/SnS heterostructure for photovoltaic applications

In this work SnS thin films were electrochemically deposited on ITO coated glass substrate by galvanostatic electrodeposition at different pH of the plating bath. The working electrode used in these studies was low cost high purity graphite rod. The as-deposited films were found to be smooth, pinhole free and well adherent to the substrate with no powdery deposition. EDX measurements revealed that all the SnS films were non-stoichiometric in nature with variation from Sn-excess to S-excess compositions. XRD pattern showed that all the SnS thin films had orthorhombic polycrystalline structure. The direct bandgaps of all the films were found to be in the range 1.54-1.58 eV. ITO/SnS/In structure exhibited linear current-voltage characteristics, establishing the ohmic nature of both ITO/SnS and SnS/In junctions. Furthermore, SnS layer was grown on CdS film using electrodeposition technique. The heterostructure ITO/CdS/SnS/In was characterized under dark and illuminated conditions. From forward biased I-V characteristics several junction parameters like barrier height, diode ideality factor and series resistance of the heterostructure were extracted using Cheung model.     

Growth, structural and optical transport properties of nanocrystal Zn1−xCdS thin films deposited by solution growth technique (SGT) for photosensor applications

Solution Growth Technique (SGT) has been used for deposition of Zn_1−xCdS nanocrystalline thin films. Various parameters such as solution pH (10.4), deposition time, concentration of ions, composition and deposition and annealing temperatures have been optimized for the development of device grade thin film. In order to achieve uniformity and adhesiveness of thin film on glass substrate, 5 ml triethanolamine (TEA) have been added in deposition solution. The as-deposited films have been annealed in Rapid Thermal Annealing (RTA) system at various temperature ranges from 100 to 500 °C in air. The changes in structural formation and optical transport phenomena have been studied with annealing temperatures and composition value (x). As-deposited films have two phases of ZnS and CdS, which were confirmed by X-ray diffraction studies; further the X-ray analysis of annealed (380 °C) films indicates that the films have nanocrystalline size (150 nm) and crystal structure depends on the films stoichiometry and annealing temperatures. The Zn_0.4CdS films annealed at 380 °C in air for 5 min have hexagonal structure where as films annealed at 500 °C have represented the oxide phase with hexagonal structure. Optical properties of the films were studied in the wavelength range 350-1000 nm. The optical band gap (E_g=2.94-2.30 eV) decreases with the composition (x) value. The effect of air rapid annealing on the photoresponse has also been observed on Zn_1−xCdS nanocrystal thin films. The Zn_1−xCdS thin film has higher photosensitivity at higher annealing temperatures (380-500 °C), and films also have mixed Zn_1−xCdS/Zn_1−xCdSO phase with larger grain size than the as-deposited and films annealed up to 380 °C. The present results are well agreed with the results of other studies.     

Investigation of CdS and CdTe thin films and influence of CdCl2 on CdTe/CdS structure

CdTe/CdS heterojunction solar cell structure has been fabricated using simple, easy and low-cost methods. To fabricate this structure, CdS and CdTe thin films are deposited onto FTO-coated conducting glass substrates by chemical bath deposition (CBD) and electrodeposition method, respectively. The optimized growth conditions are chosen for both CdS and CdTe films by investigating the optical, structural and morphological properties of both the as-deposited and annealed films. Optical measurement showed that CdS films have higher transmittance and lower absorbance, and CdTe films have lower transmittance and higher absorbance in the near infrared region. The band gap of CdS films is estimated to lie in the range 2.29–2.41 eV and that of CdTe films is in the range 1.53–1.55 eV. X-ray diffraction (XRD) study reveals that CdS and CdTe films are polycrystalline with preferential orientation of (1 1 1) plane. Scanning electron microscopy (SEM) study reveals that both films are smooth, void-free and uniformly distributed over the surface of the substrate. Fabricated CdTe/CdS structure showed the anticipated rectifying behaviour, and the rectifying behaviour is observed to improve due to CdCl₂ treatment.     

Microstructural, optical and photocatalytic properties of CdS doped TiO2 thin films

CdS doped TiO₂ thin films (with CdS content=0, 3, 6, 9 and 12 at%) were grown on glass substrates. The X-ray diffraction analysis revealed that the films are polycrystalline of monoclinic TiO₂ structure. The microstructure parameters of the films such as crystallite size (D_ν) and microstrain (e) are calculated. Both the crystallites size and the microstrain are decreased with increasing CdS content. The optical constants have been determined in terms of Murmann's exact equations. The refractive index and extinction coefficient are increased with increasing CdS content. The optical band gap is calculated in the strong absorption region. The possible optical transition in these films is found to be an allowed direct transition. The values of E_g^opt are found to decrease as the CdS content increased. The films with 3 at% CdS content have better decomposition efficiency than undoped TiO₂. The films with 6 at% and 9 at% CdS content have decomposition efficiency comparable to that of undoped TiO₂, although they have lower band gap. The CdS doped TiO₂ could have a better impact on the decomposing of organic wastes.