Synthesis, thermionic emission and magnetic properties of (NdxGd1-x)B6

Polycrystalline rare-earth hexaborides(NdxGd1-x)B6(x = 0,0.2,0.6,0.8,1) were prepared by the reactive spark plasma sintering(SPS) method using mixed powder of GdH2,NdH2 and B.The effects of Nd doping on the crystal structure,the grain orientation,the thermionic emission and the magnetic properties of the hexaboride were investigated by X-ray diffraction,electron backscattered diffraction and magnetic measurements.It is found that all the samples sintered by the SPS method exhibit high densities(> 95%) and high values of Vickers hardness(2319 kg/mm2).The values are much higher than those obtained in the traditional method.With the increase of Nd content,the thermionic emission current density increases from 11 to 16.30 A/cm2 and the magnetic phase transition temperature increases from 5.85 to 7.95 K.Thus,the SPS technique is a suitable method to synthesize the dense rare-earth hexaborides with excellent properties.     

Doping effects on structural and magnetic evolutions of orthoferrite SmFe（1-x） Alx O3

The structural and magnetic properties of SmFeO3 with B site substitution of non-magnetic atom A1 are investigated. The x-ray diffraction patterns show that SmFe（1-x）AlxO3 remains an orthorhombic structure within the whole doping range, and the unit-cell volume decreases monotonically with the increase of doped A1 concentration. Besides, the octa- hedral tilting distortions of FeO6 are found to be alleviated while the tolerance factor increases. However, the relationship between the lattice parameters and Al concentration is observed to deviate from Vegard＇s rule, and this may be caused by magnetostriction effects. For the doping content values in a range 0 〈 x 〈 0.6, the ferromagnetism, antiferromagnetism, and paramagnetism are observed to occur continuously. Moreover, the magnetization and the spin reorientation temperature （Tk） decrease monotonically as Al content value increases. With the doping content values being x = 0.8 and 1.0, these compounds only show paramagnetic behavior.     

Cation distributions estimated using the magnetic moments of the spinel ferrites Co_(1-x)Cr_xFe_2O_4 at 10K

（A）[B]2O4 ferrite samples with the composition COl_xCrxFe204 （0.0 ≤ x ≤1.0） are prepared using a hydrothermal method, and subjected to calcining in a tube furnace with an argon-flow at 1673 K for 2 h. X-ray diffraction patterns indicate that each of all the samples has a single phase cubic spinel structure with a space group of Fd3m. Magnetic measurements show that the saturation magnetization decreases with as the Cr content x increases. The cation distribution of the samples is estimated by fitting the dependence of the magnetic moments on x at l 0 K, using the quantum mechanical model previously proposed by our group. The calculated sum of the content values of the Cr3＋ and Cr2＋ cations occupying the （A） sites increases as the value of x increases. In the fitting process, the magnetic moment directions of the Cr3＋ and Cr2＋ cations are assumed to be antiparallel to those of the Fe and Co cations, respectively, which is in accordance with Hund＇s rules.     

Manipulating magnetic anisotropies of Co/MgO(001) ultrathin films via oblique deposition

We present a systematic investigation of magnetic anisotropy induced by oblique deposition of Co thin films on MgO(001) substrates by molecular beam epitaxy at different deposition angles,i.e.,0?,30?,45?,60?,and 75?with respect to the surface normal.Low energy electron diffraction(LEED),surface magneto–optical Kerr effect(SMOKE),and anisotropic magnetoresistance(AMR) setups were employed to investigate the magnetic properties of cobalt films.The values of in-plane uniaxial magnetic anisotropy(UMA) constant Ku and four-fold magnetocrystalline anisotropy constant K1 were derived from magnetic torque curves on the base of AMR results.It was found that the value of Ku increases with increasing deposition angle with respect to the surface normal,while the value of K_1 remains almost constant for all the samples.Furthermore,by using MOKE results,the Ku values of the films deposited obliquely were also derived from the magnetization curves along hard axis.The results of AMR method were then compared with that of hard axis fitting method(coherent rotation) and found that both methods have almost identical values of UMA constant for each sample.     

A novel approach to improve the field emission characteristics of printed CNT films

A novel post-treatment method, including hard hairbrush and electrical treatment, is performed intentionally to improve the field emission capability and stability of screen-printed carbon nanotubes （CNTs）. Compared with untreated films, the field emission properties of the treated ones are greatly enhanced. Scanning electron microscopy （SEM） and Raman spectrum studies reveal that field emission properties are enhanced by two factors. Firstly, the improved field emission properties of CNT films can be attributed to the more active CNT surface by removing the organic material cover on the CNTs. Secondly, the gener- ation of a high density of structural defects and the lower resistance contact to the topside CNT emitters after treatment are all helpful to improving the field emission properties of the treated CNTs.     

Electronic and optical properties of CdS/CdZnS nanocrystals

Cd1-x ZnxS nanocrystals are prepared by a co-precipitation method with different atomic fractions of Zn.The texture,structural transformation and optical properties with increasing x value in Cd1-x ZnxS are studied with scanning electron microscopy,electron diffraction patterning,and absorption spectra respectively.Quantum confinement in a strained CdS/Cd1-xZnxS related nanodot with various Zn content values is investigated theoretically.Binding energies on exciton bound CdS/CdxZn1-xS quantum dot are computed,with consideration of the internal electric field induced by the spontaneous and piezoelectric polarizations,and thereby the interband emission energy is calculated as a function of the dot radius.The optical band gap from the UV absorption spectrum is compared with the interband emission energy computed theoretically.Our results show that the average diameter of composite nanoparticles ranges from 3 nm to 6 nm.The X-ray diffraction pattern shows that all the peaks shift towards the higher diffracting angles with an increase in Zn content.The lattice constant gradually decreases as the Zn content increases.The strong absorption edge shifts towards the lower wavelength region and hence the band gap of the films increases as the Zn content increases.The values of the absorption edge are found to shift towards the shorter wave length region and hence the direct band gap energy varies from 2.5 eV for the CdS film and 3.5 eV for the ZnS film.Our numerical results are in good agreement with the experimental results.     

Effects of Annealing Temperature on Structural and Optical Properties of ZnO Thin Films

The effects of annealing temperature on the structural and optical properties of ZnO films grown on Si （100） substrates by sol-gel spin-coating are investigated. The structural and optical properties are characterized by x-ray diffraction, scanning electron microscopy and photoluminescence spectra. X-ray diffraction analysis shows the crystal quality of ZnO films becomes better after annealing at high temperature. The grain size increases with the temperature increasing. It is found that the tensile stress in the plane of ZnO films first increases and then decreases with the annealing temperature increasing, reaching the maximum value of 1.8 GPa at 700℃. PL spectra of ZnO films annealed at various temperatures consists of a near band edge emission around 380 nm and visible emissions due to the electronic defects, which are related to deep level emissions, such as oxide antisite （OZn）, interstitial oxygen （Oi）, interstitial zinc （Zni） and zinc vacancy （VZn^-）, which are generated during annealing process. The evolution of defects is analyzed by PL spectra based on the energy of the electronic transitions.     

CRYSTALLOGRAPHIC STRUCTURE AND INTRINSIC MAGENTIC PROPERTIES OF R2Fe14BNx

We found that the nitrogen atoms can enter into the R₂Fe₁₄B structure by a proper heat treatment in nitrogen atmosphere. The crystallographic structure and magnetic properties of R₂Fe₁₄BN_x, R =Nd and Y, have been investigated by using X-ray and neutron diffraction techniques as well as magnetic measurements. The neutron diffrac-tion data show that the nitrogen atoms occupy the 4f interstices. The interstitial nitrogen atoms were found to have an effect of enhancing Curie temerature, whereas, decreasing saturation magnetization and magneto-crystalline anisotropy. The rela-tionship of the crystal structure and the intrinsic magnetic properties of this crystal is discussed.     

A novel strong green phosphor： K3Gd（PO4）2：Ce^3＋, Tb^3＋ for a UV-excited white light-emitting-diode

A series of K3Gd1-x-y（PO4）2：xCe^3＋, yTb^3＋ phosphors are synthesized by the solid-sate reaction method. X-ray diffraction and photoluminescence spectra are utilized to characterize the structures and luminescence properties of the as-synthesized phosphors. Co-doping of Ce^3＋ enhances the emission intensity of Tb^3＋ greatly through an efficient energy transfer process from Ce^3＋ to Tb^3＋. The energy transfer is confirmed by photoluminescence spectra and decay time curves analysis. The efficiency and mechanism of energy transfer are investigated carefully. Moreover, due to the non- concentration quenching property of K3Tb（PO4）2, the photoluminescence spectra of K3Tb1-x（PO4）2：xCe^3＋ are studied and the results show that when x = 0.11 the strongest Tb^3＋ green emission can be realized.     

Evaluation of the 1077 keV γ-ray emission probability from 6SGa decay

6SGa decays to the excited states of aSzn through the electron capture decay mode. New recommended values for the emission probability of 1077 keV γ-ray given by the ENSDF and DDEP databases all use data from absolute measurements. In 2011, JIANG Li-Yang deduced a new value for 1077 keV γ-ray emission probability by measuring the 69Ga（n,2n） 6SGa reaction cross section. The new value is about 20% lower than values obtained from previous absolute measurements and evaluations. In this paper, the discrepancies among the measurements and evaluations are analyzed carefully and the new values are re-recommended. Our recommended value for the emission probability of 1077 keV γ-ray is （2.72±0.16）%.     

Highly Directional Emission from a Subwavelength Slit in Metal-Dielectric Layered Films

The directional light emission from a single subwavelength slit surrounded by periodic grooves in layered films consisting of Ag and transparent dielectric is analysed numerically by the finite difference time domain method. The results show that the transmission through this structure is strongly confined by the modulation of the dielectric film with grooves on the output side. The role of evanescent waves in this phenomenon is discussed. It is the re-diffraction of the evanescent waves （that are generated by the diffraction of the subwavelength slit） caused by the grooves on the dielectric film that leads to the directional transmission. Some suggestions are given to obtain beaming light with high transmittance.     

Effect of Annealing Conditions on Properties of Sol-Gel Derived Al-Doped ZnO Thin Films

Transparent conductive Al-doped ZnO （AZO） thin films are prepared on normal glass substrates by the sol-gel spin coating method. The effects of drying conditions, annealing temperature and cooling rate on the structural, electrical and optical properties of AZO films are investigated by x-ray diffraction, scanning electron microscopy, the four-point probe method and UV-VIS spectrophotometry, respectively. The deposited films show a hexagonal wurtzite structure and high preferential c-axis orientation. As the drying temperature increases from 100℃ to 300℃ the resistivity of AZO films decreases dramatically. In contrast to the annealed films cooled in a furnace and in air, the resistivity of the annealed film which is cooled at -15℃is greatly reduced. Increasing the cooling rate dramatically increases the electrical conductivity of AZO films.     

Annealing effect on structure and green emission of ZnO nanopowder by decomposing precursors

ZnO nanopowder is successfully synthesized by annealing the precursors in oxygen gas using the chemical precipitation method. Structural and optical properties of thus synthesized ZnO nanopowder are characterized by scanning electron microscopy (SEM) and photoluminescence (PL). The morphology of ZnO nanopowders evolves from nanorod to cobble as annealing temperature increases from 500 to 1000~\du, while spiral structures are observed in the samples annealed at 900 and 1000~\du. The PL spectra of ZnO nanopowder consist of largely green and yellow emission bands. The green emission from ZnO nanopowder depends strongly on the annealing temperature with a peak intensity at a temperature lower than 800~℃ while the yellow emission is associated with interstitial oxygen \rm O_\i.     

Improving the field-emission properties of carbon nanotubes by magnetically controlled nickel-electroplating treatment

A novel magnetically controlled Ni-plating method has been developed to improve the field-emission properties of carbon nanotubes (CNTs). The effect of the magnetic field and Ni-electroplating on CNT field-emission properties was investigated, and the results are demonstrated using scanning electron microscopy, J-E and the duration test. After treatment, the turn-on electric field declines from 1.55 to 0.91 V/μm at an emission current density of 100 μA/cm², and the emission current density increases from 0.011 to 0.34 mA/cm² at an electric field of 1.0 V/μm. Both the brightness and uniformity of the CNT emission performance are improved after treatment.     

The luminescence enhancement of Eu^3＋ ion and SnO2 nanocrystal co-doped sol-gel SiO2 films

SnO₂ nanocrystal and rare-earth Eu～（3+） ion co-doped SiO₂ thin films are prepared by sol-gel and spin coating methods.The formation of tetragonal rutile structure SnO₂ nanocrystals with a uniform distribution is confirmed by X-ray diffraction and transmission electron microscopy.Fourier transform infrared spectroscopy is used to investigate the densities of the hydroxyl groups,and it is found that the emission intensity from the 5 D 0 7 F 2 transitions of the Eu～（3+） ions is enhanced by two orders of magnitude due to energy transfer from the oxygen-vacancy-related defects of the SnO₂ nanocrystals to nearby Eu～（3+） ions.The influences of the amounts of Sn and the post-annealing temperatures are systematically evaluated to further understand the mechanism of energy transfer.The luminescence intensity ratio of Eu～（3+） ions from electric dipole transition and magnetic dipole transition indicate the different probable locations of Eu～（3+） ions in the sol-gel thin film,which are further discussed based on temperature-dependent photoluminescence measurements.     

In-situ growth of a CdS window layer by vacuum thermal evaporation for CIGS thin film solar cell applications

Highly crystalline and transparent CdS films are grown by utilizing the vacuum thermal evaporation （VTE） method. The structural, surface morphological, and optical properties of the films are studied and compared with those prepared by chemical bath deposition （CBD）. It is found that the films deposited at a high substrate temperature （200 ℃） have a preferential orientation along （002） which is consistent with CBD-grown films. Absorption spectra reveal that the films are highly transparent and the optical band gap values are found to be in a range of 2.44 eV-2.56 eV. Culnl_xGaxSe2 （CIGS） solar cells with in-situ VTE-grown CdS films exhibit higher values of Voc together with smaller values of Jsc than those from CBD. Eventually the conversion efficiency and fill factor become slightly better than those from the CBD method. Our work suggests that the in-situ thermal evaporation method can be a competitive alternative to the CBD method, particularly in the physical- and vacuum-based CIGS technology.     

Solution of the effects of twinning in femtosecond X-ray protein nanocrystallography

With the development of the XFEL (X-ray free electron laser), high quality diffraction patterns from nanocrystals have been achieved. The nanocrystals with different sizes and random orientations are injected to the XFEL beams and the diffraction patterns can be obtained by the so-called "diffraction-and-destruction" mode. The recovery of orientations is one of the most critical steps in reconstructing the 3D structure of nanocrystals. There is already an approach to solve the orientation problem by using the automated indexing software in crystallography. However, this method cannot distinguish the twin orientations in the cases of the symmetries of Bravais lattices higher than the point groups. Here we propose a new method to solve this problem. The shape transforms of nanocrystals can be determined from all of the intensities around the diffraction spots, and then Fourier transformation of a single crystal cell is obtained. The actual orientations of the patterns can be solved by comparing the values of the Fourier transformations of the crystal cell on the intersections of all patterns. This so-called "multiple-common-line" method can distinguish the twin orientations in the XFEL diffraction patterns successfully.     

Phase-Transition and Magnetic Moment of the Gd3+ Ion in the Gd2Fe17 Compound

The structure and magnetic phase transitions of the Gd2Fe17 compound are investigated by using a differential thermal/thermogravimetric analyzer, x-ray diffraction, and magnetization measurements. The result shows that there are two phase structures for the Gd2Fe17 compound： the hexagonal Th2Nilr-type structure at high temperatures （above 1243℃）, and the rhombohedral Th2Zn17-type structure, respectively. A method to measure the magnetic moments of the Gd-sublattice and the Fe-sublattice in the Gd2Fe17 compound is presented. The moments of the Gd-sublattice and the Fe-sublattice in the Gd2Fe17 compound from 77 to 500 K are measured in this way with a vibrating sample magnetometer. A detailed discussion is presented.     

Exchange interaction and demagnetization process of high-abundance rare-earth magnets sintered using dual alloy method

The 2:14:1-type rare-earth(RE)-Fe-B permanent magnets prepared by the dual alloy method have been found to possess much superior magnetic properties to those prepared by the single alloy method,providing an appealing route to promote the utilization of high-abundance RE elements Ce and La and balance the use of the RE source.However,the relationship between magnetic interactions among different 2:14:1 main phases and superior magnetic properties is still unclear.In this study,we investigated the magnetic interactions and reversal field distribution in these magnets using first-order reversal curve(FORC)images.The FORC images showed that(Nd,Pr)27.8(La,Ce)2.7FebalM1.4B1.0(S-9)and(Nd,Pr)19.5(La,Ce)11.0FebalM1.4B1.0(S-36)have the characteristics of multiple main phases.The reverse magnetic fields corresponding to the soft and hard main phases,as well as the associated exchange coupling,were highly dependent on the La Ce content.The higher the La Ce content,the weaker the exchange coupling and the more asynchronous the demagnetization process.In addition,the FORC images indicated that the magnetization reversal process also varies with La Ce content,where the nucleation and propagation of reversed domains dominant in the S-9 magnet,while the domain propagation in the S-36 magnet is considerably suppressed.Additional micromagnetic simulations also revealed that the coercivity and exchange coupling of multi-main-phase magnets decrease with increasing La Ce content,correlating well with the experimental results.These findings may not only contribute to a better understanding of the complex magnetic interactions between the soft and hard phases and how they affect macroscopic magnetic properties but also help in improving the magnetic performance of the RE-Fe-B magnets with high La Ce content.     

Field Emission Properties of Ball-Like Nano-Carbon Thin Films Deposited on Mo Films with Accidented Topography

Ball-like nano-earbon thin films （BNCTs） are grown on Mo layers by microwave plasma chemical vapour deposition （MPCVD） system. The Mo layers are deposited on ceramic substrates by electron beam deposition method and are pretreated by ultrasonically scratching. The optimization effects of ultrasonically scratching pretreatment on the surface micro-structures of carbon films are studied. It is found from field-emission scanning electron microscope （FE-SEM） images and Raman spectra that the surface structures of the carbon films deposited on Mo pretreated are improved, which are composed of highly uniform nano-structured carbon balls with considerable disorder structures. Field emission （FE） measurements are carried out using a diode structure. The experimental results indicate that the BNCTs exhibit good FE properties, which have the turn on field of 1.56 V/μm, and the current density of 1.0mA/cm^2 at electric field of 4.0 V/μm, the uniformly distributed emission site density from a broad well-proportioned emission area of 4 cm^2 are also obtained. Linearity is observed in Fowler Nordheim （F N） plots in higher field region, and the possible emission mechanism of BNCTs is discussed.