Optical and electrical properties of BaSnO3 and In2O3 mixed transparent conductive films deposited by filtered cathodic vacuum arc technique at room temperature

For the crystalline temperature of BaSnO$_{3}$ (BTO) was above 650 ℃, the transparent conductive BTO-based films were always deposited above this temperature on epitaxy substrates by pulsed laser deposition or molecular beam epitaxy till now which limited there application in low temperature device process. In the article, the microstructure, optical and electrical of BTO and In$_{2}$O$_{3}$ mixed transparent conductive BaInSnO$_x$ (BITO) film deposited by filtered cathodic vacuum arc technique (FCVA) on glass substrate at room temperature were firstly reported. The BITO film with thickness of 300 nm had mainly In$_{2}$O$_{3}$ polycrystalline phase, and minor polycrystalline BTO phase with (001), (011), (111), (002), (222) crystal faces which were first deposited at room temperature on amorphous glass. The transmittance was 70%-80% in the visible light region with linear refractive index of 1.94 and extinction coefficient of 0.004 at 550-nm wavelength. The basic optical properties included the real and imaginary parts, high frequency dielectric constants, the absorption coefficient, the Urbach energy, the indirect and direct band gaps, the oscillator and dispersion energies, the static refractive index and dielectric constant, the average oscillator wavelength, oscillator length strength, the linear and the third-order nonlinear optical susceptibilities, and the nonlinear refractive index were all calculated. The film was the n-type conductor with sheet resistance of 704.7 $\Omega /\Box $, resistivity of 0.02 $\Omega \cdot$cm, mobility of 18.9 cm$^{2}$/V$\cdot$s, and carrier electron concentration of $1.6\times 10^{19}$ cm$^{-3}$ at room temperature. The results suggested that the BITO film deposited by FCVA had potential application in transparent conductive films-based low temperature device process.     

Physical analysis of normally-off ALD Al2O3/GaN MOSFET with different substrates using self-terminating thermal oxidation-assisted wet etching technique

Based on the self-terminating thermal oxidation-assisted wet etching technique, two kinds of enhancement mode Al$_{2}$O$_{3}$/GaN MOSFETs (metal-oxide-semiconductor field-effect transistors) separately with sapphire substrate and Si substrate are prepared. It is found that the performance of sapphire substrate device is better than that of silicon substrate. Comparing these two devices, the maximum drain current of sapphire substrate device (401 mA/mm) is 1.76 times that of silicon substrate device (228 mA/mm), and the field-effect mobility ($\mu_{\rm FEmax}$) of sapphire substrate device (176 cm$^{2}$/V$\cdot$s) is 1.83 times that of silicon substrate device (96 cm$^{2}$/V$\cdot$s). The conductive resistance of silicon substrate device is 21.2 $\Omega {\cdot }$mm, while that of sapphire substrate device is only 15.2 $\Omega {\cdot }$mm, which is 61% that of silicon substrate device. The significant difference in performance between sapphire substrate and Si substrate is related to the differences in interface and border trap near Al$_{2}$O$_{3}$/GaN interface. Experimental studies show that (i) interface/border trap density in the sapphire substrate device is one order of magnitude lower than in the Si substrate device, (ii) Both the border traps in Al$_{2}$O$_{3}$ dielectric near Al$_{2}$O$_{3}$/GaN and the interface traps in Al$_{2}$O$_{3}$/GaN interface have a significantly effect on device channel mobility, and (iii) the properties of gallium nitride materials on different substrates are different due to wet etching. The research results in this work provide a reference for further optimizing the performances of silicon substrate devices.     

Electron field emission from single-walled carbon nanotube nonwoven

Field emission from single-walled carbon nanotube (SWNT) nonwoven has been investigated under high vacuum with different vacuum gaps. A low turn-on electric field of 1.05\,V/$\mu $m is required to reach an emission current density of 10 $\mu $A/cm$^{2}$. An emission current density of 10 mA/cm$^{2}$ is obtained at an operating electric field of 1.88\,V/$\mu $m. No current saturation is found even at an emission current of 5\,mA. With the vacuum gap increasing from 1 to 10 mm, the turn-on field decreases monotonically from 1.21 to 0.68\,V/$\mu $m, while the field amplification is augmented. The good field-emission behaviour is ascribed to the combined effects of the intrinsic field emission of SWNT and the waved topography of the nonwoven.     

The splitting of low-lying states for hydroxyl molecule under spin--orbit coupling

The splitting of potential energy curves for the states $X^{2}\Pi _{3/2}$, $^{2}\Pi _{1/2}$ and $A^{2}\Sigma ^{ +}$ of hydroxyl OH under spin--orbit coupling (SOC) has been calculated by using the SO multi-configuration quasi-degenerate perturbation theory (SO-MCQDPT). Their Murrell--Sorbie (M--S) potential functions have been derived, then, the spectroscopic constants for $X^{2}\Pi _{3/2}$,$^{ 2}\Pi _{1/2}$ and $A^{2}\Sigma ^{ + }$ have been derived from the M--S function. The calculated dissociation energies for the three states are $D_{0}$[OH($X^{2}\Pi _{3/2})$]=34966.632cm$^{-1}$, $D_{0}$[OH($^{2}\Pi _{1/2})$]=34922.802cm$^{-1}$, and $D_{0}$[OH($A^{2}\Sigma ^{ + })$]=17469.794cm$^{-1}$, respectively. The vertical excitation energy $\nu [ {{ }^2\Pi _{1/2} ( {\nu = 0} ) \to {X}{ }^2\Pi _{3/2} ( {\nu = 0} )} ] = 139.6{\rm cm}^{-{\rm 1}}$. All the spectroscopic data for the $X^{2}\Pi _{3/2}$ and $^{2}\Pi _{1/2 }$ are given for the first time except the dissociation energy of $X^{2}\Pi _{3/2}$.     

First-principles calculations for elastic properties of rutile TiO2 under pressure

This paper studies the equilibrium structure parameters and the dependences of the elastic properties on pressure for rutile TiO2 by using the Cambridge Serial Total Energy Package （CASTEP） program in the frame of density functional theory. The obtained equilibrium structure parameters, bulk modulus B0 and its pressure derivative B′0 are in good agreement with experiments and the theoretical results. The six independent elastic constants of rutile TiO2 under pressure are theoretically investigated for the first time. It is found that, as pressure increases, the elastic constants C11, C33, C66, C12 and C13 increase, The variation of elastic constant C44 is not obvious and the anisotropy will weaken.     

Ab initio calculations on the α^3∑u^＋ state properties of dimer ^7Li2

The comparison between single-point energy scanning （SPES） and geometry optimization （OPT） in determining the equilibrium geometry of the α^3∑u^＋ state for ^7Li2 is made at numerous basis sets such as 6-311＋＋G（2df）, cc-PVTZ, 6-311＋＋G（2df, p）, 6-311G（3df,3pd）, 6-311＋＋G（2df,2pd）, D95（3df,3pd）, 6-311＋＋G, DGDZVP, 6-311＋＋G（3df,2pd）, 6-311G（2df,2pd）, D95V＋＋, CEP-121G, 6-311＋＋G（d,p）, 6-311＋＋G（2df, pd） and 6-311＋＋G（3df,3pd） in full active space using a symmetry-adapted-cluster/ symmetry-adapted-cluster configuration-interaction （SAC/SAC=CI） method presented in Gaussian03 program package. The difference of the equilibrium geometries obtained by SPES and by OPT is reported. Analyses show that the results obtained by SPES are more reasonable than those obtained by OPT. We have calculated the complete potential energy curves at those sets over a wide internuclear distance range from about 3.0α0 to 37.0α0, and the conclusion is that the basis set cc-PVTZ is the most suitable one. With the potential obtained at ccopVTZ, the spectroscopic data （Te, De, D0, ωe,ωeХe, αe and Be） are computed and they are 1.006 eV, 338.71 cm^-1, 307.12 cm^-1, 64.88 cm^-1, 3.41 cm^-1, 0.0187 cm^-1 and 0.279 cm^-1, respectively, which are in good agreement with recent measurements. The total 11 vibrational states are found at J=0. Their corresponding vibrational levels and classical turning points are computed and compared with available RKR data, and good agreement is found. One inertial rotation constant （By） and six centrifugal distortion constants （Dr Hv, Lv, My, Nv, and Ov） are calculated. The scattering length is calculated to be -27.138α0, which is in good accord with the experimental data.     

Spin polarization effect for molecule Ta2

Density functional theory （DFT） （B3p86） has been used to optimize the structure of the molecule Ta2. The result shows that the ground state of molecule Ta2 is a 7-multiple state and its electronic configuration is ^7∑u^＋, which shows the spin polarization effect for molecule Ta2 of transition metal elements for the first time. Meanwhile, spin pollution has not been found because the wavefunction of the ground state does not mix with those of higher states. So, the fact that the ground state of molecule Ta2 is a 7-multiple state indicates a spin polarization effect of molecule Ta2 of the transition metal elements, i.e. there exist 6 parallel spin electrons and the non-conjugated electrons are greatest in number. These electrons occupy different space orbitals so that the energy of molecule Ta2 is minimized. It can be concluded that the effect of parallel spin of the molecule Ta2 is larger than the effect of the conjugated molecule, which is obviously related to the effect of d-electron delocalization. In addition, the Murrell-Sorbie potential functions with parameters for the ground state ^7∑u^＋ and other states of the molecule Ta2 are derived. The dissociation energy De, equilibrium bond length Re and vibration frequency we for the ground state of molecule Ta2 are 4.5513eV, 0.2433nm and 173.06cm^-1, respectively. Its force constants f2, f3 and f4 are 1.5965×10^2aJ.nm^-2, -6.4722×10^3aJ·nm^-3 and 29.4851×10^4aJ·nm^-4, respectively. Other spectroscopic data we xe, Be and αe for the ground state of Ta2 are 0.2078cm^-1, 0.0315 cm^-1 and 0.7858×10^-4 cm^-1, respectively.     

Raman analysis of defects in n-type 4H-SiC

This paper employs micro-Raman technique for detailed analysis of the defects (both inside and outside) in bulk 4H-SiC. The main peaks of the first-order Raman spectrum obtained in the centre of defect agree well with those of perfect bulk 4H-SiC, which indicate that there is no parasitic polytype in the round pit and the hexagonal defect. Four electronic Raman scattering peaks from nitrogen defect levels are observed in the round pit (395\,cm$^{-1}$, 526\,cm$^{-1}$, 572\,cm$^{-1}$, and 635\,cm$^{-1})$, but cannot be found in the spectra of hexagonal defect. The theoretical analysis of the longitudinal optical plasmon--phonon coupled mode line shape indicates the nonuniformity of nitrogen distribution between the hexagonal defect and the outer area in 4H-SiC. The second-order Raman features of the defects in bulk 4H-SiC are well-defined using the selection rules for second-order scattering in wurtzite structure and compared with that in the free defect zone.     

Judd-Oflet analysis of spectrum and laser performance of Ho：YAP crystal end-pumped by 1.91μm Tm：YLF laser

The Ho:YAP crystal is grown by the Czochralski technique.The room temperature polarized absorption spectra of Ho:YAP crystal was measured on a c cut sample with 1 at% holmium.According to the obtained Judd-Ofelt intensity parameters Ω2 = 1.42 × 10-20 cm2,Ω4 = 2.92 × 10-20 cm2,and Ω6 = 1.71 × 10-20 cm2,this paper calculated the fluorescence lifetime to be 6 ms for 5I7 →5 I8 transition,and the integrated emission cross section to be 2.24×10-18 cm2.It investigates the room temperature Ho:YAP laser end pumped by a 1.91 μm Tm:YLF laser.The maximum output power was 4.1 W when the incident 1.91 μm pump power was 14.4 W.The slope efficiency is 40.8%,corresponding to an optical to optical conversion efficiency of 28.4%.The Ho:YAP output wavelength was centred at 2118 nm with full width at half maximum of about 0.8 nm.     

Judd--Ofelt analysis of spectra and experimental evaluation of laser performance of Tm3+ doped Lu2SiO5 crystal

This paper reports that the Tm^3＋：Lu2SiO5 （Tm：LSO） crystal is grown by Czochralski technique. The roomtemperature absorption spectra of Tm：LSO crystal are measured on a b-cut sample with 4 at.% thulium. According to the obtained Judd-Ofelt intensity parameters Ω2=9.3155×10^-20 cm^2, Ω4=8.4103×10^-20 cm^2, Ω6=1.5908×10^-20 cm^2, the fluorescence lifetime is calculated to be 2.03 ms for ^3F4 → ^3H6 transition, and the integrated emission cross section is 5.81×10^-18 cm^2. Room-temperature laser action near 2μm under diode pumping is experimentally evaluated in Tm：LSO. An optical-optical conversion efficiency of 9.1% and a slope efficiency of 16.2% are obtained with continuouswave maximum output power of 0.67 W. The emission wavelengths of Tm：LSO laser are centred around 2.06μm with spectral bandwidth of -13.6 nm.     

High energy electron radiation effect on Ni/4H-SiC SBD and Ohmic contact

The Ni/4H-SiC Schottky barrier diodes (SBDs) and transfer length method (TLM) test patterns of Ni/4H-SiC Ohmic contacts were fabricated, and irradiated with 1~MeV electrons up to a dose of 3.43× 10¹⁴~e/cm^-2. After radiation, the forward currents of the SBDs at 2~V decreased by about 50%, and the reverse currents at -200~V increased by less than 30%. Schottky barrier height (φ _B ) of the Ni/4H-SiC SBD increased from 1.20~eV to 1.21~eV under 0~V irradiation bias, and decreased from 1.25~eV to 1.19~eV under -30~V irradiation bias. The degradation of φ _B could be explained by the variation of interface states of Schottky contacts. The on-state resistance (R_s) and the reverse current increased with the dose, which can be ascribed to the radiation defects in bulk material. The specific contact resistance (\rho_c) of the Ni/SiC Ohmic contact increased from 5.11× 10⁵~Ωega.cm² to 2.97× 10^-4~Ωega.cm².     

Investigation of transport properties of perovskite single crystals by pulsed and DC bias transient current technique

Time-of-flight (ToF) transient current method is an important technique to study the transport characteristics of semiconductors. Here, both the direct current (DC) and pulsed bias ToF transient current method are employed to investigate the transport properties and electric field distribution inside the MAPbI$_{3}$ single crystal detector. Owing to the almost homogeneous electric field built inside the detector during pulsed bias ToF measurement, the free hole mobility can be directly calculated to be about 22 cm$^{2}\cdot$V$^{-1}\cdot$s$^{-1}$, and the hole lifetime is around 6.5 μs-17.5 μs. Hence, the mobility-lifetime product can be derived to be $1.4\times 10^{-4}$ cm$^{2}\cdot$V$^{-1}$-$3.9\times 10^{-4}$ cm$^{2}\cdot$V$^{-1}$. The transit time measured under the DC bias deviates with increasing voltage compared with that under the pulsed bias, which arises mainly from the inhomogeneous electric field distribution inside the perovskite. The positive space charge density can then be deduced to increase from 3.1$\times10^{10}$ cm$^{-3}$ to 6.89$\times 10^{10}$ cm$^{-3}$ in a bias range of 50 V-150 V. The ToF measurement can provide us with a facile way to accurately measure the transport properties of the perovskite single crystals, and is also helpful in obtaining a rough picture of the internal electric field distribution.     

The dissociation pathways of N2+ in intense femtosecond laser fields

Using a neutral N2 beam as target,this paper studies the dissociation of N2+ in intense femtosecond laser fields(45 fs,～1×10 16 W/cm 2) at the laser wavelength of 800 nm based on the time-of-flight mass spectra of N + fragment ions.The angular distributions of N+ and the laser power dependence of N + yielded from different dissociation pathways show that the dissociation mechanisms mainly proceed through the couplings between the metastable states(A,B and C) and the upper excited states of N2+.A coupling model of light-dressed potential energy curves of N+2 is used to interpret the kinetic energy release of N+.     

Growth,characterization, and Raman spectra of the 1T phases of TiTe2, TiSe2, and TiS2

High-quality large 1$T$ phase of Ti$X_2$ ($X ={\rm Te}$, Se, and S) single crystals have been grown by chemical vapor transport using iodine as a transport agent. The samples are characterized by compositional and structural analyses, and their properties are investigated by Raman spectroscopy. Several phonon modes have been observed, including the widely reported $A_{1g}$ and $E_g$ modes, the rarely reported $E_u$ mode ($\sim$183 cm$^{-1}$ for TiTe$_2$, and $\sim$185 cm$^{-1}$ for TiS$_2$), and even the unexpected $K$ mode ($\sim$85 cm$^{-1}$) of TiTe$_2$. Most phonons harden with the decrease of temperature, except that the $K$ mode of TiTe$_2$ and the $E_u$ and "$A_{2u}$/Sh" modes of TiS$_2$ soften with the decrease of temperature. In addition, we also found phonon changes in TiSe$_2$ that may be related to charge density wave phase transition. Our results on Ti$X_2$ phonons will help to understand their charge density wave and superconductivity.     

Elastic collisions of sulfur and hydrogen in their ground states at low temperatures and spectroscopic parameters of SH（X^2∏） radical

This paper constructs the interaction potential of the SH（X^2∏） radical by using the coupled-cluster singlesdoubles-approximate-triples theory combining the correlation-consistent quintuple basis set augmented with the diffuse functions, aug-cc-pV5Z, in the valence range. Employing the potential, it accurately determines the spectroscopic parameters. The present De, Re, ωe, ωeχe, ae and Be values are of 3.7767eV, 0.13424nm, 2699.846 cm^-1, 47.7055 cm^-1, 0.2639cm^-1 and 9.4414 cm^-1, respectively, which are in excellent agreement with those obtained from the measure- ments. A total of 19 vibrational states has been found when J = 0 by solving the radial SchrSdinger equation of nuclear motion. The complete vibrational levels, classical turning points, initial rotation and centrifugal distortion constants when J = 0 are reported for the first time, which are in good accord with the experimental results. The total and various partial-wave cross sections are computed for the elastic collisions of sulfur and hydrogen in their ground states at low temperatures when two atoms approach each other along the SH（X^2∏） potential energy curve. Over the impact energy range from 1.0×10^-11 to 1.0×10^-4 a.u., eight shape resonances have been found in the total elastic cross sections. For each shape resonance, the resonant energy is accurately calculated. Careful investigations have pointed out that these resonances result from the 1 = 0, 1, 2, 3, 4, 6, 7, 8 partial-wave contributions.     

Fast-speed self-powered PEDOT: PSS/α-Ga2O3 nanorod array/FTO photodetector with solar-blind UV/visible dual-band photodetection

The $\alpha $-Ga$_{2}$O$_{3}$ nanorod array is grown on FTO by hydrothermal and annealing processes. And a self-powered PEDOT:PSS/$\alpha $-Ga$_{2}$O$_{3}$ nanorod array/FTO (PGF) photodetector has been demonstrated by spin coating PEDOT:PSS on the $\alpha $-Ga$_{2}$O$_{3}$ nanorod array. Successfully, the PGF photodetector shows solar-blind UV/visible dual-band photodetection. Our device possesses comparable solar-blind UV responsivity (0.18 mA/W at 235 nm) and much faster response speed (0.102 s) than most of the reported self-powered $\alpha $-Ga$_{2}$O$_{3}$ nanorod array solar-blind UV photodetectors. And it presents the featured and distinguished visible band photoresponse with a response speed of 0.136 s at 540 nm. The response time is also much faster than the other non-self-powered $\beta $-Ga$_{2}$O$_{3 }$ DUV/visible dual-band photodetectors due to the fast-speed separation of photogenerated carries by the built-in electric field in the depletion regions of PEDOT:PSS/$\alpha $-Ga$_{2}$O$_{3}$ heterojunction. The results herein may prove a promising way to realize fast-speed self-powered $\alpha $-Ga$_{2}$O$_{3}$ photodetectors with solar-blind UV/visible dual-band photodetection by simple processes for the applications of multiple-target tracking, imaging, machine vision and communication.     

Spin polarization effect for Os2 molecule

Density functional Theory （DFT） （B3p86） of Gaussian03 has been used to optimize the structure of Os2 molecule. The result shows that the ground state for Os2 molecule is 9-multiple state and its electronic configuration is ^9∑^＋g, which shows spin polarization effect of Os2 molecule of transition metal elements for the first time. Meanwhile, we have not found any spin pollution because the wavefunction of the ground state does not mingle with wavefunctions with higher energy states. So, the fact that the ground state for Os2 molecule is a 9-multiple state is indicative of spin polarization effect of Os2 molecule of transition metal elements. That is, there exist 8 parallel spin electrons. The non-conjugated electron is greatest in number. These electrons occupy different spacious tracks, so that the energy of Os2 molecule is minimized. It can be concluded that the effect of parallel spin of Os2 molecule is larger than the effect of the conjugated molecule, which is obviously related to the effect of electron d delocalization. In addition, the Murrell-Sorbie potential functions with the parameters for the ground state ^9∑^＋g and other states of Os2 molecule are derived. Dissociation energy De for the ground state of Os2 molecule is 3.3971eV, equilibrium bond length Re is 0.2403nm, vibration frequency ωe is 235.32cm^-1. Its force constants f2, f3, and f4 are 3.1032×10^2aJ·nm^-2, -14.3425×10^3aJ·nm^-3 and 50.5792×10^4aJ·nm^-4 respectively. The other spectroscopic data for the ground state of Os2 molecule ωexe, Be and ae are 0.4277cm^- 1, 0.0307cm^- 1 and 0.6491 × 10^-4cm^-1 respectively.     

Deposition and characterization of YBCO/CeO2/YSZ/CeO2 multilayers on biaxially textured Ni substrates

CeO2/YSZ/CeO2 buffer layers were deposited on biaxially textured Ni substrates by pulsed laser deposition. The influence of the processing parameters on the texture development of the seed layer CeO2 was investigated. Epitaxial films of YBCO were then grown in situ on the CeO2/YSZ （yttria-stabilized ZrO2）/CeO2-buffered Ni substrates. The resulting YBCO conductors exhibited self-fleld critical current density Jc of more than 1 MA/cm^2 at 77K and superconducting transition temperature Tc of about 91K.     

GaN layers with different polarities prepared by radio frequency molecular beam epitaxy and characterized by Raman scattering

GaN layers with different polarities have been prepared by radio-frequency molecular beam epitaxy (RF-MBE) and characterized by Raman scattering. Polarity control are realized by controlling Al/N flux ratio during high temperature AlN buffer growth. The Raman results illustrate that the N-polarity GaN films have frequency shifts at $A_{1}$(LO) mode because of their high carrier density; the forbidden $A_{1}$(TO) mode occurs for mixed-polarity GaN films due to the destroyed translation symmetry by inversion domain boundaries (IDBS); Raman spectra for Ga-polarity GaN films show that they have neither frequency shifts mode nor forbidden mode. These results indicate that Ga-polarity GaN films have a better quality, and they are in good agreement with the results obtained from the room temperature Hall mobility. The best values of Ga-polarity GaN films are 1042 cm$^{2}$/Vs with a carrier density of 1.0$\times $10$^{17}$~cm$^{ - 3}$.     

One-step hydrothermal synthesis of nitrogen and tungsten codoped TiO2 nanorods with high visible light photocatalytic activity

N,W codoped TiO 2 $\mathrm{TiO}_{2}$ nanorods were synthesized via a one-step hydrothermal method using ammonium metatungstate as the nitrogen and tungstate sources. The prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV–visible diffuse reflectance spectroscopy (DRS), and X-ray photoelectron spectroscopy (XPS). The results indicated that the N,W codoped TiO 2 $\mathrm{TiO}_{2}$ nanorods exhibited a higher photocatalytic activity under visible light irradiation compared with P25 and undoped TiO 2 $\mathrm{TiO}_{2}$ , because the codoping of N and W ions not only extended the visible light absorption but also promoted the separation of the photogenerated electrons and holes.