The influence of pressure on the growth of a-plane GaN on r-plane sapphire substrates by MOCVD

Nonpolar a-plane (110) GaN films have been grown on r-plane (102) sapphire by metal-organic chemical vapor deposition (MOCVD) under different growth pressures. The as-grown films are investigated by optical microscopy, high-resolution X-ray diffraction (HRXRD) and Raman scattering. As growth pressure rises from 100 mbar to 400 mbar, the surface gets rougher, and the in-plane XRD full width at half maximum (FWHM) along the c-axis [0001] increases while that along the m-axis [100] decreases. Meanwhile, res...     

Nonpolar a-plane GaN grown on r-plane sapphire using multilayer AlN buffer by metalorganic chemical vapor deposition

Mirror-like and pit-free non-polar a-plane (1 1 −2 0) GaN films are grown on r-plane (1 −1 0 2) sapphire substrates using metalorganic chemical vapor deposition (MOCVD) with multilayer high-low-high temperature AlN buffer layers. The buffer layer structure and film quality are essential to the growth of a flat, crack-free and pit-free a-plane GaN film. The multilayer AlN buffer structure includes a thin low-temperature-deposited AlN (LT-AlN) layer inserted into the high-temperature-deposited AlN (HT-AlN) layer. The results demonstrate that the multilayer AlN buffer structure can improve the surface morphology of the upper a-plane GaN film. The grown multilayer AlN buffer structure reduced the tensile stress on the AlN buffer layers and increased the compressive stress on the a-plane GaN film. The multilayer AlN buffer structure markedly improves the surface morphology of the a-plane GaN film, as revealed by scanning electron microscopy. The effects of various growth V/III ratios was investigated to obtain a-plane GaN films with better surface morphology. The mean roughness of the surface was 1.02 nm, as revealed by atomic force microscopy. Accordingly, the multilayer AlN buffer structure improves the surface morphology and facilitates the complete coalescence of the a-plane GaN layer.     

Structural and optical investigation of nonpolar a-plane GaN grown by metal-organic chemical vapour deposition on r-plane sapphire by neutron irradiation

Nonpolar (1120) a-plane GaN films are grown by metal-organic chemical vapour deposition (MOCVD) on r-plane (1102) sapphire.The samples are irradiated with neutrons under a dose of 1 × 10 15 cm 2.The surface morphology,the crystal defects and the optical properties of the samples before and after irradiation are analysed using atomic force microscopy (AFM),high resolution X-ray diffraction (HRXRD) and photoluminescence (PL).The AFM result shows deteriorated sample surface after the irradiation.Careful fitting of the XRD rocking curve is carried out to obtain the Lorentzian weight fraction.Broadening due to Lorentzian type is more obvious in the as-grown sample compared with that of the irradiated sample,indicating that more point defects appear in the irradiated sample.The variations of line width and intensity of the PL band edge emission peak are consistent with the XRD results.The activation energy decreases from 82.5 meV to 29.9 meV after irradiation by neutron.     

Effects of ion implantation on yellow luminescence in unintentional doped n-type GaN

The effects of Si, O, C and N ion implantation with different implantation doses on yellow luminescence (YL) of GaN have been investigated. The as-grown GaN samples used in the work were of unintentional doped n-type, and the photoluminescence (PL) spectra of samples had strong YL. The experimental results showed that YL of ion implanted samples exhibited marked reductions compared to samples with no implantation, while the near band edge (NBE) emissions were reduced to a lesser extent. The deep-level centers associated with YL may be produced in GaN films by O and C ion implantation, and identities of these deep-level centers were analyzed. It was also found that the dose dependence of YL was analogous with the one of the intensity ratios of YL to the near band edge (NBE) emission (I _YL /I _NBE ) for ion implanted samples. The possible reason for this comparability has been proposed.      

利用MOCVD在r面蓝宝石上生长的α面GaN中两步AlN缓冲层的优化

采用两步AlN缓冲层(一层低温AlN和一层高温AlN)在r面蓝宝石衬底上生长了非极性的α面GaN,并利用高分辨X射线衍射和光致荧光谱对所生长的材料进行了研究.两步AIN缓冲层在我们之前的工作中已被证明比单步高温AlN或低温GaN缓冲层更有利于减小材料各向异性和提高晶体质量,本文进一步优化了两步AlN缓冲层的结构,并得到...     

Unidirectional expansion of lattice parameters in GaN induced by ion implantation

This paper reports that the 150-keV Mn ions are implanted into GaN thin film grown on Al2O3 by metal-organic chemical vapour deposition.The X-ray diffraction reciprocal spacing mapping is applied to study the lattice parameter variation upon implantation and post-annealing.After implantation,a significant expansion is observed in the perpendicular direction.The lattice strain in perpendicular direction strongly depends on ion fluence and implantation geometry and can be partially relaxed by post-annealing.While in the parallel direction,the lattice parameter approximately keeps the same as the unimplanted GaN,which is independent of ion fluence,implantation geometry and post-annealing temperature.     

Structural modifications of GaN after cerium implantation

Among the family of rare earth (RE) dopants, the doping of first member Ce into GaN is the least studied system. This article reports structure properties of Ce‐doped GaN realized by technique of ion implantation. Ce ions were implanted into metal organic chemical vapor deposition grown n‐ and p‐GaN/sapphire thin films at doses 3 × 10¹⁴ and 2 × 10¹⁵ cm⁻². X‐ray diffraction scans and Raman scattering measurements exhibited expansion of lattice in the implanted portion of the samples. First order Raman scattering spectra show appearance of several disorder‐activated Raman scattering modes in addition to typical GaN features. A dose‐dependent decrease in intensity of E₂ mode was observed in Raman the spectra of the implanted samples. Ultraviolet Raman spectra of implanted samples show complete quenching of photoluminescence emission and appearance of multiple A₁(LO) phonon scattering modes up to fifth order. Moreover, a decrease in intensity and an increase in line width of LO modes as a function of wavenumber were observed for implanted samples. Copyright © 2012 John Wiley & Sons, Ltd.     

AlGaN/GaN heterostructure grown on 1 -tilt sapphire substrate by MOCVD

AlGaN/GaN epitaxial layers were grown on 0^°-tilt and 1^°-tilt sapphire substrates by metalorganic chemical vapor deposition (MOCVD). With exactly the same growth conditions, it was found that dislocation density was smaller and crystal quality was better for the AlGaN/GaN epitaxial layers prepared on 1^°-tilt sapphire substrate. We also found that AlGaN/GaN epitaxial layers on 1^°-tilt sapphire substrate were grown with step growth mode while those on 0^°-tilt substrate were grown with two-dimensional island growth. From the temperature-dependent mobility, it was found that crystal quality of the AlGaN/GaN epitaxial layer prepared on 1^°-tilt sapphire substrate is better.     

蓝宝石邻晶面衬底MBE生长GaN薄膜的瞬态光电导弛豫特性研究

在实验优化MBE工艺条件的基础上，采用蓝宝石(0001)邻晶面衬底制备出了具有较高质量的GaN薄膜.XRD分析表明邻晶面衬底生长的GaN薄膜晶体结构质量明显提高，AFM表征结果显示邻晶面生长的样品表面形貌显著改善.蓝宝石衬底GaN薄膜的瞬态光电导弛豫特性对比实验研究发现，常规衬底生长的GaN薄膜光电导弛豫特性出现双分子复合、单分子复合和弛豫振荡三个过程，持续时间分别为0.91，7.7和35.5ms；蓝宝石邻晶面衬底生长的GaN薄膜光电导弛豫过程主要是双分子复合和单分子复合过程，持续时间分别为0.78和14ms.理论分析表明MBE生长GaN薄膜的持续光电导效应主要起源于本生位错缺陷引发的深能级. 关键词： 邻晶面蓝宝石衬底 GaN薄膜 瞬态光电导 弛豫特性     

Interface defects in GaN/sapphire studied using Rutherford backscattering spectroscopy and channeling

GaN on sapphire was grown by MOCVD technique. Rutherford backscattering spectra together with channeling along [0 0 0 1] axis were recorded to study the defects at the interface. Detailed calculation shows that the defects at GaN/sapphire interface are due to dislocations which are distributed into the whole thickness of the film and are mainly aligned on the growth direction.     

金属有机物化学气相沉积生长的a(11-20)面GaN三角坑缺陷的消除研究

用金属有机物化学气相沉积方法在r面蓝宝石上生长了非极性a面GaN薄膜,通过采用AlGaN多量子阱插入层,得到了高质量的非极性GaN材料.用原子力显微镜和高分辨X射线衍射仪研究了a面GaN的表面形貌和结晶质量,发现非极性材料上典型的三角坑缺陷被消除,(11-20)面X射线双晶摇摆曲线的半峰宽为680″.     

Threading dislocation density comparison between GaN grown on the patterned and conventional sapphire substrate by high resolution X-ray diffraction

GaN epifilms are grown on the patterned sapphire substrates (PSS) (0001) and the conventional sapphire substrates (CSS) (0001) by metal-organic chemical vapor deposition (MOCVD) using a novel two-step growth. High resolution X-ray diffraction (HR-XRD) is used to investigate the threading dislocation (TD) density of the GaN epifilms. The TD density is calculated from the ω-scans full width at half maximum (FWHM) results of HR-XRD. The edge dislocation destiny of GaN grown on the PSS is 2.7×108 cm-2, which is less than on the CSS. This is confirmed by the results of atomic force microscopy (AFM) measurement. The lower TD destiny indicates that the crystalline quality of the GaN epifilms grown on the PSS is improved compared to GaN epifilms grown on the CSS. The residual strains of GaN grown on the PSS and CSS are compared by Raman Scattering spectra. It is clearly seen that the residual strain in the GaN grown on PSS is lower than on the CSS.     

Optical parameters of epitaxial GaN thin film on Si substrate from the reflection spectrum

A method has been proposed for determining the optical properties of a thin film layer on absorbing substrates. The film optical parameters such as thickness, refractive index, absorption coefficient, extinction coefficient and the optical energy gap of an absorbing film are retrieved from the interference fringes of the reflection spectrum at normal incidence. The envelopes of the maxima of the spectrum E_M and of the minima E_m are introduced in analytical forms to find the reflectance amplitudes at the interfaces and approximate values of the thin film refractive index. Then, the interference orders and film thickness are calculated to get accurate values of the needed optical parameters. There are no complex fitting procedures or assumed theoretical refractive index dispersion relations. The method is applied to calculate the optical properties of an epitaxial gallium nitride thin film on a silicon (1 1 1) substrate. Good agreement between our results and the published data are obtained.     

AlN/蓝宝石模板上生长的GaN研究

研究了在分子束外延制备的AlN/蓝宝石模板上采用金属有机物化学气相外延生长的非故意掺杂GaN的材料性质.采用X射线衍射(XRD)、透射电镜(TEM)和原子力显微镜研究了AlN模板的晶体质量和表面相貌对GaN的影响.结果表明,当AlN的表面粗糙度较小时,尽管AlN模板的位错密度较高((102)面XRD ω扫描半高全宽900—1500 arcsec),但生长得到的GaN依然具有和在蓝宝石衬底上采用"二步法"生长的GaN可比拟的晶体质量((002)面XRD ω扫描半高全宽200—30 关键词： 氮化镓 氮化铝 金属有机物化学气相外延     

Stress and morphology of a nonpolar a-plane GaN layer on r-plane sapphire substrate

The anisotropic strain of a nonpolar (1120) a-plane GaN epilayer on an r-plane (1102) sapphire substrate, grown by low-pressure metal-organic vapour deposition is investigated by Raman spectroscopy. The room-temperature Raman scattering spectra of nonpolar a-plane GaN are measured in surface and edge backscattering geometries. The lattice is contracted in both the c- and the m-axis directions, and the stress in the m-axis direction is larger than that in the c-axis direction. On the surface of this sample, a number of cracks appear only along the m-axis, which is confirmed by the scanning electron micrograph. Atomic force microscopy images reveal a significant decrease in the root-mean-square roughness and the density of submicron pits after the stress relief.     

硅衬底InGaN/GaN基蓝光发光二极管droop效应的研究

InGaN/GaN基阱垒结构LED当注入的电流密度较大时, LED的量子效率随注入电流密度增大而下降, 即droop效应.本文在Si (111)衬底上生长了 InGaN/GaN 基蓝光多量子阱结构的LED,通过将实验测量的光电性能曲线与利用ABC模型模拟的结果进行对比, 探讨了droop效应的成因.结果显示:温度下降会阻碍电流扩展和降低空穴浓度, 电子在阱中分布会越来越不平衡,阱中局部区域中因填充了势能越来越高的电子而溢出阱外, 从而使droop效应随着温度的降低在更小的电流密度下出现且更为严重, 不同温度下实验值与俄歇复合模型模拟的结果在高注入时趋势相反.这此结果表明,引起 droop效应的主因不是俄歇非辐射复合而是电子溢出,电子溢出的本质原因是载流子在阱中分布不均衡.     

Surface chemical disorder and lattice strain of GaN implanted by 3-MeV Fe10+ ions

Chemical disorder on the surface and lattice strain in GaN implanted by Fe¹⁰⁺ ions are investigated. In this study, 3-MeV Fe¹⁰⁺ ions fluence ranges from 1×10¹³ ions/cm² to 5×10¹⁵ ions/cm² at room temperature. X-ray photoelectron spectroscopy, high-resolution x-ray diffraction, and high-resolution transmission electron microscopy were used to characterize lattice disorder. The transition of Ga-N bonds to oxynitride bonding is caused by ion sputtering. The change of tensile strain out-of-plane with fluence was measured. Lattice disorder due to the formation of stacking faults prefers to occur on the basal plane.     

离子注入和固相外延制备Si1-x-yGexCy半导体薄膜

用等离子体增强化学气相淀积(PECVD)生长了200nm的SiGe薄膜,然后将C离子注入SiGe层,经两步热退火处理制备了Si1-x-yGexCy三元合金半导体薄膜.应用卢瑟福背散射(RBS),傅里叶变换红外光谱(FTIR)和高分辨率x射线衍射(HRXRD)研究了薄膜的结构和外延特性.发现C原子基本处于替代位置,C原子的掺入缓解了SiGe层的压应变 关键词： Si1-x-yGexCy薄膜 离子注入 固相外延     

Effect of hydrogen defects on nanocrystallite layers of Si solar cells by hydrogen implantation

The Si solar cells were irradiated with high energy hydrogen ions of 10, 30, 60 and 120?keV at the dose rate of 10¹⁷ H⁺ ions (proton)/cm². The structural, optical and electrical properties of the implanted samples and fabricated cells were studied. The implantation induced defects bringing structural changes before and after annealing was evidenced by the transmission electron microscopy. The Raman spectrum showed a change of crystalline to amorphous state at 480?cm^?1 when the sample was implanted by hydrogen ion of 30?keV energy. Formation of nanocrystallite layers were observed after annealing. The electroluminescence images showed that hydrogen-related defect centers were involved in the emission mechanism. The photoluminescence emission from the implanted cells was attributed to nanocrystallite layers. From current–voltage measurements, the conversion efficiencies of implanted Si solar cells were found lower than the un-implanted reference cell. The ion implantation did not passivate the defects rather acted as recombination centers.