Improved device performance of recessed-gate AlGaN/GaN HEMTs by using in-situ N2O radical treatment

The N₂O radicals in-situ treatment on gate region has been employed to improve device performance of recessed-gate AlGaN/GaN high-electron-mobility transistors (HEMTs). The samples after gate recess etching were treated by N₂O radicals without physical bombardment. After in-situ treatment (IST) processing, the gate leakage currents decreased by more than one order of magnitude compared to the sample without IST. The fabricated HEMTs with the IST process show a low reverse gate current of 10^-9 A/mm, high on/off current ratio of 10⁸, and high f_T×L_g of 13.44 GHz· μm. A transmission electron microscope (TEM) imaging illustrates an oxide layer with a thickness of 1.8 nm exists at the AlGaN surface. X-ray photoelectron spectroscopy (XPS) measurement shows that the content of the Al-O and Ga-O bonds elevated after IST, indicating that the Al-N and Ga-N bonds on the AlGaN surface were broken and meanwhile the Al-O and Ga-O bonds formed. The oxide formed by a chemical reaction between radicals and the surface of the AlGaN barrier layer is responsible for improved device characteristics.     

Impact of gate offset in gate recess on DC and RF performance of InAlAs/InGaAs InP-based HEMTs

A set of 100-nm gate-length InP-based high electron mobility transistors (HEMTs) were designed and fabricated with different gate offsets in gate recess. A novel technology was proposed for independent definition of gate recess and T-shaped gate by electron beam lithography. DC and RF measurement was conducted. With the gate offset varying from drain side to source side, the maximum drain current (I_ds,max) and transconductance (g_m,max) increased. In the meantime, f_T decreased while f_max increased, and the highest f_max of 1096 GHz was obtained. It can be explained by the increase of gate-source capacitance and the decrease of gate-drain capacitance and source resistance. Output conductance was also suppressed by gate offset toward source side. This provides simple and flexible device parameter selection for HEMTs of different usages.     

High linearity AlGaN/GaN HEMT with double-Vth coupling for millimeter-wave applications

We demonstrated an AlGaN/GaN high electron mobility transistor(HEMT)namely double-Vthcoupling HEMT(DVC-HEMT)fabricated by connecting different threshold voltage(Vth)values including the slant recess element and planar element in parallel along the gate width with N;O plasma treatment on the gate region.The comparative studies of DVC-HEMT and Fin-like HEMT fabricated on the same wafer show significantly improved linearity of transconductance(Gm)and radio frequency(RF)output signal characteristics in DVC-HEMT.The fabricated device shows the transconductance plateau larger than 7 V,which yields a flattened fT/fmax-gate bias dependence.At the operating frequency of 30 GHz,the peak power-added efficiency(PAE)of 41%accompanied by the power density(Pout)of 5.3 W/mm.Furthermore,the proposed architecture also features an exceptional linearity performance with 1-d B compression point(P1 d B)of 28 d Bm,whereas that of the Fin-like HEMT is 25.2 d Bm.The device demonstrated in this article has great potential to be a new paradigm for millimeter-wave application where high linearity is essential.     

Enhancement-mode AlGaN/GaN high electronic mobility transistors with thin barrier

An enhancement-mode (E-mode) AlGaN/GaN high electron mobility transistor (HEMTs) was fabricated with 15-nm AlGaN barrier layer. E-mode operation was achieved by using fluorine plasma treatment and post-gate rapid thermal annealing. The thin barrier depletion-HEMTs with a threshold voltage typically around --1.7 V, which is higher than that of the 22-nm barrier depletion-mode HEMTs (--3.5 V). Therefore, the thin barrier is emerging as an excellent candidate to realize the enhancement-mode operation. With 0.6-μ m gate length, the devices treated by fluorine plasma for 150-W RF power at 150 s exhibited a threshold voltage of 1.3 V. The maximum drain current and maximum transconductance are 300 mA/mm, and 177 mS/mm, respectively. Compared with the 22-nm barrier E-mode devices, V_T of the thin barrier HEMTs is much more stable under the gate step-stress.     

A novel Si-rich SiN bilayer passivation with thin-barrier AlGaN/GaN HEMTs for high performance millimeter-wave applications

We demonstrate a novel Si-rich SiN bilayer passivation technology for AlGaN/GaN high electron mobility transistors (HEMTs) with thin-barrier to minimize surface leakage current to enhance the breakdown voltage. The bilayer SiN with 20-nm Si-rich SiN and 100-nm Si$_{3}$N$_{4}$ was deposited by plasma-enhanced chemical vapor deposition (PECVD) after removing 20-nm SiO$_{2}$ pre-deposition layer. Compared to traditional Si$_{3}$N$_{4}$ passivation for thin-barrier AlGaN/GaN HEMTs, Si-rich SiN bilayer passivation can suppress the current collapse ratio from 18.54% to 8.40%. However, Si-rich bilayer passivation leads to a severer surface leakage current, so that it has a low breakdown voltage. The 20-nm SiO$_{2}$ pre-deposition layer can protect the surface of HEMTs in fabrication process and decrease Ga-O bonds, resulting in a lower surface leakage current. In contrast to passivating Si-rich SiN directly, devices with the novel Si-rich SiN bilayer passivation increase the breakdown voltage from 29 V to 85 V. Radio frequency (RF) small-signal characteristics show that HEMTs with the novel bilayer SiN passivation leads to $f_{\rm T}/f_{\rm max}$ of 68 GHz/102 GHz. At 30 GHz and $V_{\rm DS} = 20$ V, devices achieve a maximum $P_{\rm out}$ of 5.2 W/mm and a peak power-added efficiency (PAE) of 42.2%. These results indicate that HEMTs with the novel bilayer SiN passivation can have potential applications in the millimeter-wave range.     

AlGaN/GaN high-electron-mobility transistors with transparent gates by Al-doped ZnO

AlGaN/GaN high-electron-mobility transistors （HEMTs） with Al-doped ZnO （AZO） transparent gate electrodes are fabricated, and Ni/Au/Ni-gated HEMTs are produced in comparison. The AZO-gated HEMTs show good DC characteristics and Schottky rectifying characteristics, and the gate electrodes achieve excellent transparencies. Compared with Ni/Au/Ni-gated HEMTs, AZO-gated HEMTs show a low saturation current, high threshold voltage, high Schottky barrier height, and low gate reverse leakage current. Due to the higher gate resistivity, AZO-gated HEMTs exhibit a current-gain cutoff frequency （fT） of 10 GHz and a power gain cutoff frequency （fmax） of 5 GHz, and lower maximum oscillation frequency than Ni/Au/Ni-gated HEMTs. Moreover, the C-V characteristics are measured and the gate interface characteristics of the AZO-gated devices are investigated by a C-V dual sweep.     

Enhancement of fMAX of InP-based HEMTs by double-recessed offset gate process

A double-recessed offset gate process technology for InP-based high electron mobility transistors (HEMTs) has been developed in this paper. Single-recessed and double-recessed HEMTs with different gate offsets have been fabricated and characterized. Compared with single-recessed devices, the maximum drain-source current (I_D,max) and maximum extrinsic transconductance (g_m,max) of double-recessed devices decreased due to the increase in series resistances. However, in terms of RF performance, double-recessed HEMTs achieved higher maximum oscillation frequency (f_MAX) by reducing drain output conductance (g_ds) and drain to gate capacitance (C_gd). In addition, further improvement of f_MAX was observed by adjusting the gate offset of double-recessed devices. This can be explained by suppressing the ratio of C_gd to source to gate capacitance (C_gs) by extending drain-side recess length (L_rd). Compared with the single-recessed HEMTs, the f_MAX of double-recessed offset gate HEMTs was increased by about 20%.     

High power-added-efficiency AlGaN/GaN HEMTs fabricated by atomic level controlled etching

An atomic-level controlled etching(ACE)technology is invstigated for the fabrication of recessed gate AlGaN/GaN high-electron-mobility transistors(HEMTs)with high power added efficiency.We compare the recessed gate HEMTs with conventional etching(CE)based chlorine,Cl₂-only ACE and BCl³/Cl₂ACE,respectively.The mixed radicals of BCl₃/Cl₂were used as the active reactants in the step of chemical modification.For ensuring precise and controllable etching depth and low etching damage,the kinetic energy of argon ions was accurately controlled.These argon ions were used precisely to remove the chemical modified surface atomic layer.Compared to the HEMTs with CE,the characteristics of devices fabricated by ACE are significantly improved,which benefits from significant reduction of etching damage.For BCl₃/Cl₂ACE recessed HEMTs,the load pull test at 17 GHz shows a high power added efficiency(PAE)of 59.8%with an output power density of 1.6 W/mm at Vd=10 V,and a peak PAE of 44.8%with an output power density of 3.2 W/mm at Vd=20 V in a continuous-wave mode.     

The effects of ⁶⁰Co γ-ray irradiation on the DC characteristics of enhancement-mode AlGaN/GaN high-electron-mobility transistors

The effects of 60Co γ-ray irradiation on the DC characteristics of AlGaN/GaN enhancement-mode high-electron-mobility transistors (E-mode HEMTs) are investigated. The results show that having been irradiated by 60Co γ-rays at a dose of 3 Mrad (Si), the E-mode HEMT reduces its saturation drain current and maximal transconductance by 6% and 5%, respectively, and significantly increases both forward and reverse gate currents, while its threshold voltage is affected only slightly. The obvious performance degradation of E-mode AlGaN/GaN HEMTs is consistent with the creation of electronegative surface state charges in the source-gate spacer and gate-drain spacer after being irradiated.     

基于GaN同质衬底的高迁移率AlGaN/GaNHEMT材料

研究了表面预处理对GaN同质外延的影响,获得了高电子迁移率AlGaN/GaN异质结材料.通过NH_3/H_2混合气体与H_2交替通入反应室的方法对GaN模板和GaN半绝缘衬底进行高温预处理.研究结果表明,NH_3/H_2能够抑制GaN的分解,避免粗糙表面,但不利于去除表面的杂质,黄光带峰相对强度较高;H_2促进GaN分解,随时间延长GaN分解加剧,导致模板表面粗糙不平,AlGaN/GaN HEMT材料二维电子气迁移率降低.采用NH_3/H_2混合气体与H_2交替气氛模式处理模板或衬底表面,能够清洁表面,去除表面杂质,获得平滑的生长表面和外延材料表面,有利于提高AlGaN/GaN HEMT材料电学性能.在GaN衬底上外延AlGaN/GaN HEMT材料,2DEG迁移率达到2113 cm~2/V·s,电学性能良好.     

The effects of 60Co γ-ray irradiation on the DC characteristics of enhancement-mode AlGaN/GaN high-electron-mobility transistors

The effects of 60Co γ-ray irradiation on the DC characteristics of AlGaN/GaN enhancement-mode high-electron-mobility transistors (E-mode HEMTs) are investigated. The results show that having been irradiated by 60Co γ-rays at a dose of 3 Mrad (Si), the E-mode HEMT reduces its saturation drain current and maximal transconductance by 6% and 5%, respectively, and significantly increases both forward and reverse gate currents, while its threshold voltage is affected only slightly. The obvious performance degradation of E-mode AlGaN/GaN HEMTs is consistent with the creation of electronegative surface state charges in the source-gate spacer and gate-drain spacer after being irradiated.     

二维圆盘颗粒体系声学行为的数值研究

数值测量了卸载过程中二维单分散圆盘颗粒系统的横波、纵波声速、声衰减系数、非线性系数随压强的变化以及声衰减系数随频率的变化.结果表明,二维(2D)圆盘颗粒体系的横波、纵波声速均随压强呈分段幂律标度:当压强P10~(-4)时,横波、纵波声速随压强的增大而减小;当P10~(-4)时,有v_t~P~(0.202),v_l~P~(0.338).进一步得到其剪切模量和体积模量的比值G/B也随压强呈幂律标度,G/B~P~(-0.502),暗示在低压强下,与三维(3D)球形颗粒体系类似,2D圆盘颗粒体系也处于L玻璃态.水平激励和垂直激励下2D圆盘颗粒系统的衰减系数随频率变化也呈现分段行为:当频率f0.05时,衰减系数不随f变化;当f0.05时,横波纵波的衰减系数α~f;当f0.35时,横波衰减系数α_T~f~2,纵波衰减系数α_L~f~(1.5).此外,竖直水平激励下的2D圆盘颗粒系统的非线性系数和衰减系数随压强也呈现与声速类似的分段规律:当P10~(-4)时,横波非线性系数β_T~P~(-0.230),其余都不随压强变化.当P10~(-4)时,两者均随压强增大呈幂律减小:β_T~P~(-0.703),β_L~P~(-0.684),α_T~P~(-0.099),α_L~P~(-0.105).进而得到2D圆盘颗粒系统中散射相关的特征长度?~*随压强呈幂律标度,当P10~(-4)时,?~*~P~(-0.595);当P10~(-4)时,?~*~P~(0.236).     

DLTS characterization of silicon nitride passivated AlGaN/GaN heterostructures

Passivating the ungated surface of AlGaN/GaN HEMTs with silicon nitride (SiN) is effective in improving the microwave output power performances of these devices. However, very little information is available about surface states in GaN-based HEMTs after SiN passivation. In this work we investigate AlGaN/GaN HEMTs structures having either metal–semiconductor or metal–SiN–semiconductor gate contacts. In short gate devices conductance DLTS measurements point out a hole-like peak that shows an anomalous behaviour and can be ascribed to surface states in the access regions of the device. In insulated gate HEMTs a band of levels is detected and ascribed to surface states, whose energy ranges from 0.14 to 0.43 eV. Capacitance–voltage measurements allow us to point out the existence of a second band of interface states deeper in energy than the former one. This band is responsible for slow transients observed in the characteristics of the insulated gate FAT-HEMT.     

基于原位等离子体氮化及低压化学气相沉积-Si_3N_4栅介质的高性能AlGaN/GaN MIS-HEMTs器件的研究

通过对低压化学气相沉积(LPCVD)系统进行改造,实现在沉积Si_3N_4薄膜前的原位等离子体氮化处理,氮等离子体可以有效地降低器件界面处的氧含量和悬挂键,从而获得了较低的LPCVD-Si_3N_4/GaN界面态,通过这种技术制作的MIS-HEMTs器件,在扫描栅压范围V_(G-sweep)=(-30 V,+24 V)时,阈值回滞为186 mV,据我们所知为目前高扫描栅压V_(G+)(20 V)下的最好结果.动态测试表明,在400 V关态应力下,器件的导通电阻仅仅上升1.36倍(关态到开态的时间间隔为100μs).     

High-electric-field-stress-induced degradation of SiN passivated AlGaN/GaN high electron mobility transistors

AlGaN/GaN high electron mobility transistors (HEMTs) are fabricated by employing SiN passivation, this paper investigates the degradation due to the high-electric-field stress. After the stress, a recoverable degradation has been found, consisting of the decrease of saturation drain current I_Dsat, maximal transconductance g_m, and the positive shift of threshold voltage V_TH at high drain-source voltage V_DS. The high-electric-field stress degrades the electric characteristics of AlGaN/GaN HEMTs because the high field increases the electron trapping at the surface and in AlGaN barrier layer. The SiN passivation of AlGaN/GaN HEMTs decreases the surface trapping and 2DEG depletion a little during the high-electric-field stress. After the hot carrier stress with V_DS=20 V and V_GS=0 V applied to the device for 10⁴ sec, the SiN passivation decreases the stress-induced degradation of I_Dsat from 36% to 30%. Both on-state and pulse-state stresses produce comparative decrease of I_Dsat, which shows that although the passivation is effective in suppressing electron trapping in surface states, it does not protect the device from high-electric-field degradation in nature. So passivation in conjunction with other technological solutions like cap layer, prepassivation surface treatments, or field-plate gate to weaken high-electric-field degradation should be adopted.     

新型宽温区高热稳定性微波功率SiGe 异质结双极晶体管

宽温区大电流下的热不稳定性严重制约着功率SiGe 异质结双极晶体管 (HBT) 在射频和微波电路中的应用.为改善器件的热不稳定性, 本文利用SILVACO TCAD建立的多指功率SiGe HBT模型, 分析了器件纵向结构中基区Ge组分分布对微波功率SiGe HBT电学特性和热学特性的影响. 研究表明, 对于基区Ge组分为阶梯分布的HBT, 由于Ge组分缓变引入了少子加速电场, 使它与均匀基区Ge组分HBT相比, 具有更高的特征频率f_T, 且电流增益β和f_T随温度变化变弱, 这有利于防止器件在宽温区工作时电学特性的漂移.同时, 器件整体温度有所降低, 但器件各指温度分布均匀性较差.考虑多指HBT各发射极指散热能力存在差异, 在器件纵向结构设计为基区Ge组分阶梯分布的同时, 对其横向版图进行发射极指间距渐变结构设计, 用于改善器件各指温度分布的均匀性, 进而提高HBT的热稳定性.结果表明, 与基区Ge组分为均匀分布的等发射极指间距结构HBT相比, 新器件各指温度分布均匀性明显改善, f_T保持了较高的值, 且β和f_T 随温度变化不敏感, 热不稳定性得到显著改善, 显示了新器件在宽温区大电流下工作的优越性. 关键词： SiGe 异质结双极晶体管 Ge组分分布 发射极指间距渐变技术 热稳定性     

Photoresponse and trap characteristics of transparent AZO-gated AlGaN/GaN HEMT

AZO-gated and Ni/Au-gated AlGaN/GaN HEMTs are fabricated successfully,and an excellent transparency of AZOgated electrode is achieved.After a negative gate bias stress acts on two kinds of the devices,their photoresponse characteristics are investigated by using laser sources with different wavelengths.The effect of photoresponse on AZO-gated electrode device is more obvious than on Ni/Au-gated electrodes device.The electrons are trapped in the AlGaN barrier of AZO-gated HEMT after it has experienced negative gate bias stress,and then the electrons can be excited effectively after it has been illuminated by the light with certain wavelengths.Furthermore,the trap state density D_T and the time constantτ_T of the AZO-gated Schottky contact are extracted by fitting the measured parallel conductance in a frequency range from10 kHz to 10 MHz.The constants of the trap range from about 0.35 μs to 20.35 μs,and the trap state density increased from1.93×l0~(13)eV 1·cm~2 at an energy of 0.33 eV to 3.07×10~(11) eV~1·cm~2 at an energy of 0.40 eV.Moreover,the capacitance and conductance measurements are used to characterize the trapping effects under different illumination conditions in AZO-gated HEMTs.Reduced deep trap states' density is confirmed under the illumination of short wavelength light.     

阶梯AlGaN外延新型Al0.25Ga0.75N/GaNHEMTs器件实验研究

本文报道了作者提出的阶梯AlGaN外延层新型AlGaN/GaN HEMTs结构的实验结果. 实验利用感应耦合等离子体刻蚀(ICP)刻蚀栅边缘的AlGaN外延层, 形成阶梯的AlGaN 外延层结构, 获得浓度分区的沟道2DEG, 使得阶梯AlGaN外延层边缘出现新的电场峰, 有效降低栅边缘的高峰电场, 从而优化了AlGaN/GaN HEMTs器件的表面电场分布. 实验获得了阈值电压-1.5 V的新型AlGaN/GaN HEMTs器件. 经过测试, 同样面积的器件击穿电压从传统结构的67 V提高到新结构的106 V, 提高了58%左右; 脉冲测试下电流崩塌量也比传统结构减少了30%左右, 电流崩塌效应得到了一定的缓解.     

高温AlN插入层对AlGaN/GaN异质结材料和HEMTs器件电学特性的影响

研究了在GaN缓冲层中插入40 nm厚高温AlN层的GaN外延层和AlGaN/GaN异质结材料, AlN插入层可以增加GaN层的面内压应力并提高AlGaN/GaN高电子迁移率晶体管（HEMTs）的电学特性. 在精确测量布拉格衍射角的基础上定量计算了压应力的大小. 增加的压应力一方面通过增强GaN层的压电极化电场, 提高了AlGaN/GaN异质结二维电子气（2DEG）面密度, 另一方面使AlGaN势垒层对2DEG面密度产生的两方面影响相互抵消. 同时, 这种AlN插入层的采用降低了GaN与AlGaN层之间的 关键词： 高温AlN插入层 AlGaN/GaN异质结 二维电子气 应力     

DC and analog/RF performance of C-shaped pocket TFET (CSP-TFET) with fully overlapping gate

A C-shaped pocket tunnel field effect transistor (CSP-TFET) has been designed and optimized based on the traditional double-gate TFETs by introducing a C-shaped pocket region between the source and channel to improve the device performance. A gate-to-pocket overlapping structure is also examined in the proposed CSP-TFET to enhance the gate controllability. The effects of the pocket length, pocket doping concentration and gate-to-pocket overlapping structure on the DC and analog/RF characteristics of the CSP-TFET are estimated after calibrating the tunneling model in double-gate TFETs. The DC and analog/RF performance such as on-state current (I_on), on/off current ratio (I_on/I_off), subthreshold swing (SS) transconductance (g_m), cut-off frequency (f_T) and gain-bandwidth product (GBP) are investigated. The optimized CSPTFET device exhibits excellent performance with high I_on (9.98×10 ^{- 4} A/μm), high I_on/I_off (～ 10¹¹), as well as low SS (～ 12 mV/dec). The results reveal that the CSP-TFET device could be a potential alternative for the next generation of semiconductor devices.