Phase Behavior in Blends of Ethylene Oxide–Propylene Oxide Copolymer and Poly(ether sulfone) Studied by Modulated-Temperature DSC and NMR Relaxometry

The state diagram of a blend consisting of a copolymer containing ethylene oxide and propylene oxide, P(EO-ran-PO), and poly(ether sulfone), PES, is constructed by using modulated-temperature differential scanning calorimetry (MTDSC), T₂ NMR relaxometry, and light scattering. The apparent heat capacity signal in MTDSC is used for the characterization of polymer miscibility and morphology development. T₂ NMR relaxometry is used to detect the onset of phase separation, which is in good agreement with the onset of phase separation in the apparent heat capacity from MTDSC and the cloud-point temperature as determined from light scattering. The coexistence curve can be constructed from T₂ values at various temperatures by using a few blends with well-chosen compositions. These T₂ values also allow the detection of the boundary between the demixing zones with and without interference of partial vitrification and are in good agreement with stepwise quasi-isothermal MTDSC heat capacity measurements. Important interphases are detected in the heterogeneous P(EO-ran-PO)/PES blends.     

Greater insight into the MTDSC technique involving fundamental sinusoidal heat flow equations

Summary Modulated temperature DSC was investigated, comparing data found experimentally to that derived from theory. Deviation from theory was found with regard to the amplitude of the modulated heat flow signal when large modulation amplitudes were employed in the experiment. These deviations were determined to be dependent on the absolute temperature and it was concluded that further investigation of the heat flow signal obtained during MTDSC experiments is required.     

A MTDSC analysis of phase transition in polyurethane-organoclay nanocomposites

Modulated differential scanning calorimetry (MTDSC) was applied to investigate the phase transition behaviour of polyurethane/organoclay nanocomposites. The endotherm transitions located at 50-80 and 140 °C were re-analysed through revealed thermal features in the MTDSC reversing, non-reversing and dC_p/dT curves. It was proposed that the diffused interfacial phase exists between hard and soft phases in the polyurethane system. The assignment of endotherm at 140 °C is attributed to the hard microphase domain transition, which is similar to an order-disorder transition. The transition in the region of 50-80 °C reveals the relaxation of segments in the interface resulted by annealing. The addition of organoclay resulted in a reduction of hard domain ordering level. A simple method for quantitatively estimating the amount of polymer chains intercalated into layers of clay was introduced, and the relationship between the weight fraction (ω_p), of the polymer intercalated into layers and the weight fraction (ω_c), of clay was established.     

Identification of irradiated sage tea (Salvia officinalis L.) by ESR spectroscopy

The use of electron spin resonance (ESR) spectroscopy to accurately distinguish irradiated from unirradiated sage tea was examined. Before irradiation, sage tea samples exhibit one asymmetric singlet ESR signal centered at g=2.0037. Besides this central signal, two weak satellite signals situated about 3 mT left and right to it in radiation-induced spectra. Irradiation with increasing doses caused a significant increase in radiation-induced ESR signal intensity at g=2.0265 (the left satellite signal) and this increase was found to be explained by a polynomial varying function. The stability of that radiation-induced ESR signal at room temperature was studied over a storage period of 9 months. Also, the kinetic of signal at g=2.0265 was studied in detail over a temperature range 313–353 K by annealing samples at different temperatures for various times.     

Kinetics of Temperature-induced and Reaction-induced Phase Separation Studied by Modulated Temperature DSC

Temperature-induced phase separation of P(EO75-ran-PO25)/PES and reaction-induced phase separation of DGEBA/MDA modified with PVME are studied using MTDSC as an in-situ tool. Phase separation can be probed by the onset of an ‘excess’ contribution in the MTDSC heat capacity signal, in good correspondence with the cloud point temperature. This feature enables the complete construction of the state diagram of P(EO75-ran-PO25)/PES. The detection of phase separation-induced partial vitrification of the high-T_g phase (PES-rich phase) enables to sub-divide the LCST-type heterogeneous region in a zone 1 (no interference of partial vitrification) and a zone 2 (interference of partial vitrification of the PES-rich phase). This sub-division of the heterogeneous region has drastic implications on the remixing behavior of demixed blends. In DGEBA/MDA modified with PVME, reaction-induced phase separation accompanied by an increase in reaction rate, followed by a vitrification step of the epoxy-amine phase can be detected in-situ. In non-isothermal conditions, a diffusion-controlled reaction after vitrification and a final devitrification of the system is also observed.     

Mechanistic modeling of the reaction kinetics of phenyl glycidyl ether (PGE) + aniline using heat flow and heat capacity profiles from modulated temperature DSC

Modulated temperature DSC (MTDSC) has been performed on phenyl glycidyl ether (PGE) + aniline in order to obtain the non-reversing heat flow and heat capacity profiles simultaneously in a wide range of cure temperatures and mixture compositions. The epoxy (PGE) conversion as determined from the former signal corresponds to the one obtained from separate high performance liquid chromatography (HPLC), while the latter signal contains information on the individual reaction steps. Optimized kinetic parameters using a mechanistic approach, including both reactive and non-reactive complexes can successfully simulate MTDSC measurements for isothermal reaction temperatures ranging from 50 to 120 °C and for non-isothermal experiments with mixture compositions corresponding to concentrations of aniline in a range from 1.68 to 6.53 mol kg⁻¹. Concentration profiles for three mixture compositions as obtained from HPLC are also well predicted. The activation energies for the primary amine and secondary amine-epoxy reaction catalyzed by hydroxyl groups are 50 and 52 kJ mol⁻¹, respectively, while the initiation of the reaction corresponds to the primary amine-epoxy reaction catalyzed by primary amine groups with an activation energy of 72 kJ mol⁻¹. A negative substitution effect can be calculated at 0.18 from the ratio of secondary amine to primary amine-epoxy reaction rate constants.     

Influence of the efficacy of interfacial modification on the coarsening of cocontinuous PS/HDPE blends during quiescent annealing

This article studies the quiescent annealing of three different cocontinuous polystyrene/high‐density polyethylene blends modified with two types of interfacial agents of widely different efficacies. Quantitative analysis of phase growth was obtained using mercury porosimetry. In a previous work, it was shown that one of these modifiers, a symmetrical diblock copolymer, has a high affinity for the interface and demonstrates virtually no micelle formation prior to saturation of the blend interface. The other modifier, a hydrogenated SEBS of 70/30 composition, forms micelles at elevated concentrations of modifier. In this study, it is shown that the cocontinuous phase size grows linearly without modifier, whereas the addition of both interfacial modifiers significantly suppresses the PE/PS phase coarsening and results in nonlinear phase growth behavior. The effect of the diblock copolymer on suppressing coarsening, however, is much more effective than that for the triblock case clearly supporting the tendency toward micelle formation for that latter modifier. In the case of unmodified PE/PS, the driving force for capillary pressure effects is so high that it is the capillary instability phenomena that dominate the coarsening and hence result in a linear growth of pore size with annealing time. When interfacial modifiers are added, the influence of reduced interfacial tension and lower pore size polydispersity significantly diminishes both capillary pressure effects and capillary instability phenomena. In that case, capillary pressure becomes the main rate determining step resulting in a nonlinear dependence of pore size with annealing time. It is shown that both the viscosity of the phases and the temperature of annealing can strongly influence coarsening behavior at low levels of interfacial modifier. Under all those conditions, however, nonlinear phase growth for the partially compatibilized system was maintained. These results clearly show that careful quantitative coarsening experiments using mercury porosimetry can be used as a tool to analyze the efficacy of interfacial modifiers for highly continuous or cocontinuous systems. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 711–721, 2006     

On the application of an oxygen probe in chemical kinetics: The influence of the probe response on kinetic measurement

Membrance covered oxygen probes are frequently used to monitor the progress of chemical reactions involving dissolved oxygen. For reactions that are comparable in rate to the response of the oxygen probe it is difficult to obtain the correct kinetic constants directly from the probe signal with traditional kinetic data manipulation methods. In this article, we apply the method of impulse response function to describe the probe signal of an oxygen probe for three different types of simple chemical reactions. The impulse response function is obtained experimentally. Using the impulse response function we have obtained the relationships between the probe signal and the kinetic parameters of these reactions. The slow response of the probe has two effects on the kinetic curves of the reaction studied: a time-lag and distortion of the shape of the kinetic curve throughout the reaction. The latter effect becomes significant when the reaction is fast. Procedures to obtain the correct kinetic information from the oxygen probe signal are described. © 1995 John Wiley & Sons, Inc.     

Extraction of kinetic information from single-molecule experiments.

We discuss two possible approaches for extracting kinetic information from single-molecule experiments. The first approach is based on computing correlation functions from measured fluorescence signals, and the second on studying the statistics of on and off times of the same fluorescence signal. We show that in both cases it is possible to extract kinetic information about the nature of intramolecular fluctuations of the single molecule. We show that for single-molecule kinetics the intramolecular fluctuations produce stochastic memory effects which lead to new dynamic features that do not exist in traditional chemical kinetics. In particular, we investigate a new type of chemical oscillations in correlation functions observed experimentally by Edman and Rigler (Proc. Natl. Acad. Sci. USA 2000, 97, 8266).     

Detection method for ionic species based on the electroacoustic effect

The development and application of a new ion detection method based on the electroacoustic (EA) effect is described. An EA signal, produced by applying a pulsed-type electric field to an electrolyte solution in an electroacoustic cell, is dependent on the electrical and thermal properties of the electrolyte and can be detected by using a conventional gas microphone system. The EA signals, generated in this fashion, are proportional to the square of the amplitude of the pulsed-type electric field and show an inverse dependence on the modulated frequency, as found in other acoustic detection systems. The results of this study demonstrate that the EA signals observed with the new system display a linear dependence on the concentration of the electrolyte over a 3 order-of-magnitude concentration range (ca. 10(-7)-10(-4) M). The detection limit of this system was shown to be as low as 29.9 ppb for an aqueous solution of HCl. The results also indicate that the EA signal is proportional to the equivalent conductivity of electrolytes in aqueous solution. As a consequence, the new method has the potential of being used as a universal detector for ions in solutions. An important property of this detection system is that it can be applied to in situ ion detection, and as a result, it can be employed in kinetic studies to follow the progress of ionic chemical reactions.     

酞菁铅在石墨烯表面吸附行为的拉曼光谱研究

利用石墨烯增强拉曼散射效应可以获得与石墨烯接触的某些分子的拉曼增强信号, 并且对于不同的分子或振动模, 其拉曼增强因子不同. 根据这一特征, 本工作利用拉曼光谱技术对石墨烯表面上酞菁铅(PbPc)分子Langmuir-Blodgett (LB)膜在退火过程中吸附构型的变化进行了跟踪研究. 发现随着退火温度的升高, 石墨烯表面上PbPc分子的拉曼信号经历了一个先增强后减弱的过程, 在升华温度点附近强度达到最大, 表明PbPc发生了由直立向平躺取向的转变; 同时, 在PbPc分子升华温度点附近, 由于对称性破坏导致散射截面低的振动模出现, 并且该振动模强度随着退火温度的进一步升高而增强, 表明非平面的PbPc分子受石墨烯π-π相互作用的影响而形变加剧, 向平面结构转变; 在更高的退火温度下, 则出现一些不属于PbPc分子的拉曼振动峰, 表明PbPc分子在石墨烯表面由Pb(II)被还原成Pb(0).     

Development of an aminocarboxylic acid-modified infrared chemical sensor for selective determination of tyrosine in urine

An infrared (IR) chemical sensor based on immobilization of an acidified tris(2-aminoethyl)amine (ATAA) for the detection of tyrosine in urine is described. The sensing phase (i.e., coating) was saturated with nickel ions so that it would interact with tyrosine molecules in aqueous solution through the formation of stable ATAA-Ni²⁺-tyrosine complexes. Investigation of the signals of nine amino acids shows that only the three containing phenyl groups could be detected by this sensor system. A unique spectral feature located at 1515 cm⁻¹ allowed tyrosine to be discriminated from the other two amino acids. To examine the performance of the ATAA sensing phase in the quantitative analysis of tyrosine, the effects of several factors were examined. pH affected the ability of tyrosine to form complexes; the optimal signal occurred at ca. pH 8. The concentration of ammonia buffer also affected the analytical signals through a competition effect; lower concentrations of ammonia buffer provided higher intensity signals. It was found that nickel ions are the most useful for detection of tyrosine. Although the concentration of nickel ions had less influence on the analytical signal than did the concentration of the ammonia buffer, the signal intensity was optimal when the nickel ions and the target molecule had similar concentrations. The detected time profiles indicated that the ATAA sensor phase functioned via a surface adsorption mechanism. The linear range of signal intensities was up to 600 μM with a detection limit of 30 μM.     

Optical probes of intradiskal processes in rod photoreceptors. II: Light-scattering study of ATP-dependent light reactions

Rod outer segment (ROS) disks, either stacked or freely floating, respond to flash illumination to yield a specific, ATP-dependent, light-scattering signal AL. In broken ROS AL signals occur only when AD signals have preceded them. The degree to which the preceding AD signal has been completed determines the amplitude of the following AL signal. However, in freshly detached ROS from dark-adapted frogs Al signals with maximal size can be obtained without pre-incubation with exogenous ATP. The energized state, which is restored in broken ROS with the help of ATP, appears to prevail in the living retina and must therefore be considered to be "physiological". AL signals require structurally intact disks. Neither peripheral ROS proteins nor connecting filaments between adjacent disks are necessary. Their structural origin is the same as that of the preceding AD signal, i.e. osmotic disk swelling. AL signals consist of a single slow kinetic component (half-life 10 s at room temperature) and multiphase fast kinetic component (70 ms). The slow phase corresponds to a light-stimulated resumption of ATPase activity (this has been dealt with in a previous paper) whereas the fast component reflects an immediate response of the energized disk to the metarhodopsin I to metarhodopsin II transition. The latter effect is the subject of this paper. A variety of experiments, using different ATPase inhibitors, ionophores and membrane-permeable salts, have been carried out; they are all consistent with notion that AL originates in the disk interior and probes the existence of a proton electrochemical potential difference delta mu (H+) across the disk membrane. A model is presented which can explain all given properties of AL satisfactorily. According to this model the photolysis of rhodopsin causes a proton release in the disk lumen. This, in turn, results in osmotic swelling of the disks, provided that the internal buffer sites have been (at least partially) titrated with protons prior to the flash. Such conditions, i.e. a low internal pH, are provided by the proton transport across the disk membrane, which presumably takes place during the course of the preceding AD signal.     

The Development of Gas-flow Modulation for High-frequency MTDSC measurements

The purpose of this study was to investigate the feasibility of modulating the temperature programme of a conventional DSC by use of an alternating gas-flow system. Modulated temperature differential scanning calorimetry (MTDSC) is an important thermal analysis technique but suffers from a limited applicable frequency range due to the mass of the sample and DSC cell leading to the impingement of thermal conductivity effects. We suggest that the frequency limit can be increased by replacing the cell as the source of temperature modulation with an external gaseous source, directed towards the sample and reference pans. In this evaluation, an alternating gas-flow was passed through a line to a forced gas-flow accessory (FGFA). The FGFA consisted of two matched cylinders containing chambers that allowed pre-temperature-equilibration of the stream of gas before it was passed over the sample and reference pans. The development of this device revealed the essential practical requirements of gas-flow modulation for high-frequency temperature modulation. These include the following: an appropriately sealed tunable gas supply to both sample and reference pans, an effective method for high-frequency cycling of the gas-flow rate, a small aperture to deliver the flowing gas directly over the pan and a temperature equilibration chamber. The results from samples of quenched PET and amorphous Saquinavir indicate that gas-flow modulation is indeed feasible, with the FGFA able to raise the attainable temperature modulation frequency by an order of magnitude compared to conventional MTDSC. This revised version was published online in August 2006 with corrections to the Cover Date.     

Neural networks for kinetic parameters determination, signal filtering and deconvolution in thermal analysis

Feedforward neural networks have been used for kinetic parameters determination and signal filtering in differential scanning calorimetry. The proper learning function was chosen and the network topology was optimized, using an empiric procedure. The learning process was achieved using simulated thermoanalytical curves. The resilient-propagation algorithm have led to the best minimization of the error computed over all the patterns. Relative errors on the thermodynamic and kinetic parameters were evaluated and compared to those obtained with the usual thermal analysis methods (single scan methods). The errors are much lower, especially in presence of noisy signals. Then, our program was adapted to simulate thermal effects with known thermodynamic and kinetic parameters, generated electrically, using a PC computer and an electronic interface on the serial port. These thermal effects have been generated by using an inconel thread.     

Effect of single-walled carbon nanotubes and carbon nanofibers on the structure and mechanical properties of thermoplastic polyimide matrix films

The effects of additives of single-walled carbon nanotubes prepared via electric-arc synthesis and carbon nanofibers produced via gas-phase synthesis on the crystallization capacities and mechanical and electric properties of composite films of a thermoplastic polyimide (PI) matrix based on 1,3-bis-(3,3′, 4,4′-dicarboxyphenoxy)benzene and 4,4′-bis-(4-aminophenoxy)biphenyl after their uniaxial drawing and additional annealing are studied. The use of these fillers induces the heterogeneous nucleation of a crystalline phase of PI on the nanoparticle surface. A higher specific interface area in the case of addition of carbon nanotubes relative to that of carbon nanofibers leads to the formation of the crystalline structure of PI with a small crystallite size and high imperfection. Uniaxial drawing leads to the formation of a supermolecular structure that is optimum for crystallization during additional annealing and removes the kinetic hindrances to crystal growth. The properties of these fillers have a significant effect on the orientation of the nanoparticles and the matrix macromolecules during the uniaxial drawing of the films, which is accompanied by an increase in the elastic modulus with an increase in the draw ratio and the ability of the composite films to undergo orientational crystallization during additional annealing.     

Fe/Dy非晶多层膜晶化反应的热力学及动力学研究

由Miedema半经验公式计算出了Fe Dy二元系自由能图以揭示Fe Dy非晶多层膜的晶化本质。晶化受热力学和动力学两种因素控制 ,Fe,Dy晶态自由能低于初始非晶态 ,提供了晶化的热力学驱动力 ,而形核势垒及临界晶核尺寸控制了晶化反应的相选择 ,因而中等温度退火时先出现Fe晶粒 ,继而Dy晶粒 ,不出现金属间化合物。     

Effect of methanol quality on the ionisation of herbicides,insecticides and fungicides using gradient elution liquid chromatography

This paper explores the changes in the electrospray signal response of 39 structurally different compounds caused by the quality of the methanol, when used as a component in a gradient elution mobile phase. When three batches of LC–MS grade methanol from one manufacturer were evaluated, the largest variation in the electrospray signal responses of the 39 compounds examined was 18%. However, significant enhancement of the electrospray signals of up to 106% were observed among different brands of LC–MS grade methanol from different manufacturers. The effect of methanol quality on signal response was found to be compound dependent. This study also demonstrated that the senescence of the methanol was important. Using an expired batch of LC–MS grade methanol, electrospray signals were suppressed by as much as 95% for all compounds measured using positive mode electrospray. Conversely, the negative mode electrospray signals of compounds such as 4-octyl benzoic acid showed an enhancement of up to 96% when using the same batch of methanol. Linuron was used as a model compound to examine the change in the electrospray response, during gradient elution, when the proportion of an expired batch of methanol was varied. An infusion experiment showed that the linuron signal intensity decreased as the proportion of expired methanol increased in the mobile phase, which was in direct contrast to the increase in linuron signal observed with a non-expired batch of methanol. A series of isocratic experiments also showed that the linuron signal decreased as the proportion of expired methanol increased in the mobile phase. The ion ratios of several of the compounds studied changed significantly when using the expired batch of LC–MS methanol. The change in the ion ratios accentuates the difficulty of identifying compounds from in-source spectral libraries. A protocol is recommended for assessing the quality of methanol for LC–MS applications.     

The lipid composition determines the kinetics of adhesion and spreading of liposomes on mercury electrodes

The dependence of membrane properties on their composition was studied by following the adhesion and spreading of unilamellar and multilamellar liposomes on static mercury electrodes with the help of chronoamperometry. The analysis of the peak-shaped signals allows determining the kinetic parameters of the three-step adhesion-spreading process. The presence of cholesterol in the membrane stabilizes the bilayer in the liquid-crystalline phase, and destabilizes the gel phase. The kinetic parameters also show the effect of superlattice formation in the DMPC-cholesterol system. The detergent triton X-100 is only incorporated in the liquid-crystalline DMPC membranes, and it is expelled to the solution when the membrane is transformed to the gel phase. In the liquid-crystalline membrane, it enhances the adhesion-spreading of liposomes on mercury. The lytic peptides mastoparan X and melittin affect the adhesion-spreading in a similar manner. For the rupture-spreading step, their effect is explained by pore formation. The results obtained with lecithins of different length suggest that the bilayer opening process has much in common with flip-flop translocations. For this process the activation energies were found to be independent of the chain length of the lecithin molecules, while the preexponential factor in the Arrhenius equation decreases drastically for longer chains.     

Kinetic study of competing first-order processes: simultaneous quantification of hemoglobin and methemoglobin in whole blood

The development and evaluation of a kinetic method for the simultaneous quantification of methemoglobin and hemoglobin is described. A unique feature of the reaction/monitoring system is that the two species produce signals that change in opposite directions. Attempts to optimize the reaction conditions, procedures for preparing reliable standards, a new multiwavelength method used for comparison purposes and results for synthetic standards and blood samples to which known amounts of methemoglobin are added are described. Combined effects of competing directions of signal change, large concentration differences and conditions required for pseudo-first-order behavior results in a relativity narrowly defined set of conditions that permit simultaneous determinations. Even so, results for methemoglobin were in reasonable agreement between the kinetic and spectrophotometric methods (slope 1.05, intercept 0.17 mmol l^?1); difficulties in achieving pseudo-first-order behavior yielded less reliable results for hemoglobin with a least-squares slope of 1.16 for a comparison of results by kinetic and spectrophotometric methods. This latter problem had an adverse effect on comparison of percentages of methemoglobin in samples even though concentration values were in good agreement.