Thermogravimetric analysis of photodegraded acrylic coated lime wood

A series of experiments were carried out to investigate the photodegradation of lime wood (Tilia cordata Mill.) coated with acrylic copolymer during artificial UV/Vis light irradiation for 600 h. Photodegradation of the Paraloid B72 films and Paraloid B72 treated lime wood samples was evaluated by thermogravimetry throughout the irradiation period of 100 h. The results obtained indicate a shifting of the DTG maxima to lower temperatures, which may be related to a decrease in the stability of the copolymer and wood during photodegradation. The decrease of weight loss with increasing time of exposure was observed, while the global kinetic parameters for the main peak increases when increasing exposure time of wood to the UV light. Even when the surface of the wood was covered with a thin layer of acrylic resin, some photodegradation reactions of the wood surface occurred. The modifications in the wood structure may be influenced by the newly formed structures from acrylic resin photodegradation.     

Effect of fluorinated groups on photooxidative stability of polymeric protectives applied on marble

Some new protective copolymers and a commercial one have been tested on Candoglia marble, a very low porosity stone. Two of the polymers contained a partially fluorinated methacrylic monomer, 2,2,2 trifluoro ethyl methacrylate (TFEMA), in combination with either an acrylic, methyl acrylate (MA) or a vinyl ether, n-butyl vinyl ether (n-BVE) unit. Two copolymers, ethyl methacrylate/n-butyl vinyl ether and ethyl methacrylate (EMA)/methyl acrylate (Paraloid B72), were non-fluorinated and similar in compositions and molar ratio. The aim of the work is to test the copolymers and compare the performances of fluorinated new polymers with the non fluorinated one and with the largely used commercial product. The results obtained demonstrate that the introduction, even in limited amounts, of fluorine atoms in the side ester groups of methacrylic type polymers really improves their protective effect and the durability of the stone treatments. The best results were obtained with the copolymer TFEM/MA which is the fluorinated homologous of Paraloid B72.     

Evaluation of polymers for conservation treatments of outdoor exposed stone monuments. Part I: Photo-oxidative weathering

The commercial acrylic polymers, Paraloid B72 and Paraloid B67, and a silicon-based product, Dri-Film 104, commonly used as water repellents/consolidants in the restoration of stone artefacts, have been tested to evaluate their performances when submitted to ageing, simulating the outdoor conditions of treated stone. After full characterization, the three polymers were applied as thin films on slides, as thick film on petri dishes and on marble by brush or by imbibition and the resulting samples were submitted to photo-oxidative weathering (λ = 340 nm). The weathering evolution was checked by ultrasonic and colorimetric measurements and by FT-IR, NMR and SEC determinations. Removability tests were also performed. All the polymers underwent irreversible modifications with reduction of their conservative properties, colour change and, above all, impossibility of their complete removal.     

Interaction of SO3 with c-ZrO2(111) films on Pt(111)

Single-crystalline sulfated c-ZrO2(111) films of the cubic (c) type have been prepared by reactive deposition of Zr onto Pt(111) in an O2 atmosphere and subsequent exposition to a SO3 atmosphere. The morphology, atomic structure, and composition have been examined by scanning tunneling microscopy, low-energy electron diffraction (LEED), Auger electron spectroscopy, and density functional theory (DFT) calculations. The clean c-ZrO2(111) films display a (2x2) surface structure. During SO3 exposure at room temperature, a clear (radical3xradical3)R30 degrees structure develops. At about 700 K, the SO3-induced (radical3xradical3)R30 degrees structure disappears and the bright (2x2) LEED pattern of the clean ZrO2 films reappears. The energies of plausible c-ZrO2(111)/SO3 structures have been examined by DFT. The (radical3xradical3)R30 degrees structure found in the experiments turned out to be the most stable one for temperatures below 700 K. At temperatures around 700 K, a disordered low coverage structure may exist, which can not be observed by conventional LEED. A comparison of cubic zirconia surfaces with the alternative tetragonal system yields similar results for the SO3 adsorption in the DFT calculations and shows that c-ZrO2 surfaces are good models for the industrial used tetragonal ZrO2 supports.     

Evaluation of polymers for conservation treatments of outdoor exposed stone monuments. Part II: Photo-oxidative and salt-induced weathering of acrylic-silicone mixtures

The behaviour of the acrylic-silicone mixture commonly known as Bologna Cocktail, composed of commercial acrylic polymer Paraloid B72 and the silicon-based product, Dri Film 104, extensively employed as stone preservative for monuments in the last thirty years, has been tested on specimens appropriately prepared and submitted to ageing simulating reliable outdoor environment. After chemical characterization, the acrylic-silicone mixture was applied as thin film on slides, as thick film on Petri dishes and on marble by brush or by absorption; the resulting samples were artificially aged by light and saline solution. The chemical modifications were evaluated by FT-IR, NMR and SEC determinations, while preservative properties were tested by removability tests, ultrasonic and colorimetric measurements. The mixture consists of two immiscible phases and the two components have distinctive chemical behaviours, leading - after ageing - to irreversible molecular modifications and loss of conservative properties. The deterioration processes identified through laboratory simulation have been also verified on treated marble surfaces of two Venetian case studies.     

Preparation and artificial ageing tests in stone conservation of fluorosilicone vinyl acetate/acrylic/epoxy polymers

In this work, a series of fluorosilicone vinyl acetate/acrylic/epoxy (FVAE) polymers for protection of stone relics were prepared with different content of hexafluorobutyl methacrylate (HFBMA) by the seed emulsion polymerization process. Properties and structure of FVAE materials were characterized by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TG), and transmission electron microscopy (TEM). Viscosity, particle size, surface tension, gel content, adhesion and surface hardness of polymer materials were also determined. Surface morphology of the stone sample was observed by scanning electron microscopy (SEM). Compared with a commercial copolymer, ethyl methacrylate/methyl acrylate (EM/MA, Paraloid B72), protection ability of the prepared FVAE polymer was investigated using artificial ageing tests such as the freeze-thaw aging test, acid aging test and the soluble salts aging test. It was found that the FVAE polymers prepared can effectively prevent corrosion caused by H⁺, formation of an interface crack and further weathering, which indicates their possible application in stone protection.     

Ab initio thermodynamics examination of sulfur species present on Rh, Ni, and binary Rh-Ni surfaces under steam reforming reaction conditions

The stable form of adsorbed sulfur species and their coverage were investigated on Rh, Ni, and Rh-Ni binary metal surfaces using density functional theory calculations and the ab initio thermodynamics framework. S adsorption, SO(x) (x = 1-4) adsorption, and metal sulfide formation were examined on Rh(111) and Ni(111) pure metals. Both Rh and Ni metals showed a preference for S surface adsorption rather than SO(x) adsorption under steam reforming conditions. The transition temperature from a clean surface (<(1)/(9) ML) to S adsorption was identified on Rh(111), Ni(111), Rh(1)Ni(2)(111), and Rh(2)Ni(1)(111) metals at various P(H(2))/P(H(2)S) ratios. Bimetallic Rh-Ni metals transition to a clean surface at lower temperatures than does the pure Rh metal. Whereas Rh is covered with (1)/(3) ML of sulfur under the reforming conditions of 4-100 ppm S and 800 °C, Rh(1)Ni(2) is covered with (1)/(9) ML of sulfur at the lower end of this range (4-33 ppm S). The possibility of sulfate formation on Rh catalysts was examined by considering higher oxygen pressures, a Rh(221) stepped surface, and the interface between a Rh(4) cluster and CeO(2)(111) surface. SO(x) surface species are stable only at high oxygen pressure or low temperatures outside those relevant to the steam reforming of hydrocarbons.     

反相气相色谱法表征1-烯丙基-3-甲基氯代咪唑离子液体的表面性质

采用反相气相色谱(IGC)技术研究了不同温度下1-烯丙基-3-甲基氯代咪唑(［AMIM］Cl)的表面性质。以正己烷、正庚烷、正辛烷和正壬烷作为非极性探针分子测定［AMIM］Cl在343.15、353.15、363.15和373.15 K温度下的表面色散自由能;以二氯甲烷、三氯甲烷、丙酮、乙酸乙酯、四氢呋喃作为极性探针分子测定离子液体Lewis酸碱性质,并测定了吸附自由能和吸附自由焓变等热动力学参数。实验结果表明,［AMIM］Cl的酸解离平衡常数Ka为0.34,碱解离平衡常数Kb为1.68,其表面呈Lewis两性偏碱性特点。在343.15、353.15、363.15和373.15 K温度下,［AMIM］Cl的表面色散自由能分别为52.26、50.82、46.08和42.05 mJ/m2。这一结果对研究离子液体的表面性质及应用有指导作用。     

Interrelations between Adsorption Energies and Local Isotherms, Local Monolayer Capacities, and Energy Distribution Functions, as Determined for Heterogeneous Surfaces by Inverse Gas Chromatography

Physicochemical parameters for adsorption of gases at the submonolayer regions of heterogeneous solid surfaces are measured experimentally as a function of time, and then interrelated as local isotherms θ against adsorption energy varepsilon, fractional changes of adsorption sites f(varepsilon)/c*(max) against varepsilon, θ against f(varepsilon)/c*(max), and distribution functions θ f(varepsilon)/c*(max) over adsorption energy values varepsilon, without using at all the well-known integral equation Theta(p, T)=integral(infinity)(0)θ(p, T, varepsilon)f(varepsilon)dvarepsilon and assumptions concerning the pair f(varepsilon) and θ(p, T, varepsilon). The method uses only chromatographic experimental data obtained by the inverse gas chromatography technique known as reversed-flow gas chromatography. It has been applied to the adsorption of cis-2-butene and trans-2-butene onto particles of Penteli marble at temperatures of 302, 314, 323, and 333 K. The results obtained are comparable with those calculated on the basis of the well-known integral equation. Copyright 2001 Academic Press.     

Au(111)上Pd电沉积初始阶段ECSTM——PdSO_4溶液研究

应用电化学扫描隧道显微镜(ECSTM)研究了PdSO4溶液中Au(111)电极表面Pd的电化学沉积过程.实验表明,Pd的沉积初始阶段在Au(111)电极表面依次生成两个满单层Pd膜,这一实验结果不仅与电位扫描一致,而且更进一步地证明了起初的两个Pd单层形成过程乃以层～层外延方式生长.高分辨的原子图像表明吸附的SO2-4离子在外延生长的Pd膜表面形成了有序的(3×7)R19°结构.     

Diffusion and adsorption measurements in porous solids by inverse gas chromatography

The new inverse gas chromatography methodology of reversed-flow gas chromatography has been applied to measure diffusion and adsorption in porous solids. The theoretical analysis leads to equations describing the experimental data with very few approximations. From these, the total overall rate constant of transference (k = k(R) + k(2)), its probable error, the diffusion coefficient (D(1)) into porous solids (alpha-alumina and gamma-alumina), and its probable error are calculated by means of a simple PC program. The methodology was applied to pentane, hexane, and heptane diffusing into porous alpha- and gamma-alumina at various temperatures. A comparison of the results is made with those obtained by the Knudsen formula and with those of other researchers.     

Solubility and diffusion of CO2 and H2S in the ionic liquid 1-ethyl-3-methylimidazolium ethylsulfate

The solubility and diffusion coefficient were determined for carbon dioxide and hydrogen sulfide gases in the ionic liquid 1-ethyl-3-methylimidazolium ethylsulfate ([emim][EtSO₄]) at temperatures ranging from (303.15 to 353.15) K and pressures up to 1.6 MPa. The Krichevsky–Kasarnovsky equation was used to correlate solubility data and Henry’s law constants at different temperatures were obtained. The partial molar thermodynamic functions of solution such as Gibbs free energy, enthalpy, and entropy were calculated using the solubility data. A semi-infinite volume approach is used to obtain the diffusion coefficients for CO₂ and H₂S and a correlation equation with temperature is presented for each gas. Comparison showed that H₂S is more soluble than CO₂ and its diffusion coefficient is about two orders of magnitude as that of CO₂ in the ionic liquid studied in this work.     

Reaction of SO2 with AuCeO2(111): importance of O vacancies in the activation of gold

Synchrotron-based high-resolution photoemission was used to study the adsorption and chemistry of SO(2) on AuCeO(2)(111) and AuO(x)CeO(2) surfaces. The heat of adsorption of the molecule on Au nanoparticles supported on stoichiometric CeO(2)(111) was 4-7 kcalmol larger than on Au(111). However, there was negligible dissociation of SO(2) on the AuCeO(2)(111) surfaces. The full decomposition of SO(2) was observed only after introducing O vacancies in the ceria support. AuO(x)CeO(2) surfaces were found to be much less chemically active than AuCeO(2)(111) or AuCeO(2-x)(111) surfaces. The active sites in {Au + AuO(x)}ceria catalysts should involve pure gold nanoparticles in contact with O vacancies.     

Characterization of some acrylic anion-exchangers by pyrolysis-gas chromatography

Pyrolysis-gas chromatography was used in the study of the thermal behaviour of some acrylic anion-exchangers for identification of the thermal decomposition products and their percentage estimation. The acrylic anion-exchangers were prepared by aminolysis of cross-linked acrylic ester copolymer with difunctional amines. The pyrolysis-gas chromatography studies, coupled with data obtained by thermogravimetry, showed that the acrylic anion-exchangers first lose the water easily absorbed from the air, and the decomposition starts at temperatures above 100°. The great number of decomposition products identified in the pyrograms on the thermal degradation of acrylic anion-exchangers indicated a complex degradation mechanism, with important variations in the contents of the evolved amine compounds.     

Activation of gold on titania: adsorption and reaction of SO(2) on Au/TiO(2)(110)

Synchrotron-based high-resolution photoemission and first-principles density-functional slab calculations were used to study the interaction of gold with titania and the chemistry of SO(2) on Au/TiO(2)(110) surfaces. The deposition of Au nanoparticles on TiO(2)(110) produces a system with an extraordinary ability to adsorb and dissociate SO(2). In this respect, Au/TiO(2) is much more chemically active than metallic gold or stoichiometric titania. On Au(111) and rough polycrystalline surfaces of gold, SO(2) bonds weakly and desorbs intact at temperatures below 200 K. For the adsorption of SO(2) on TiO(2)(110) at 300 K, SO(4) is the only product (SO(2) + O(oxide) --> SO(4,ads)). In contrast, Au/TiO(2)(110) surfaces (theta;(Au) < or = 0.5 ML) fully dissociate the SO(2) molecule under identical reaction conditions. Interactions with titania electronically perturb gold, making it more chemically active. Furthermore, our experimental and theoretical results show quite clearly that not only gold is perturbed when gold and titania interact. The adsorbed gold, on its part, enhances the reactivity of titania by facilitating the migration of O vacancies from the bulk to the surface of the oxide. In general, the complex coupling of these phenomena must be taken into consideration when trying to explain the unusual chemical and catalytic activity of Au/TiO(2). In many situations, the oxide support can be much more than a simple spectator.     

Separation characteristics of fatty acid methyl esters using SLB-IL111, a new ionic liquid coated capillary gas chromatographic column

The ionic liquid SLB-IL111 column, available from Supelco Inc., is a novel fused capillary gas chromatography (GC) column capable of providing enhanced separations of fatty acid methyl esters (FAMEs) compared to the highly polar cyanopropyl siloxane columns currently recommended for the separation of cis- and trans isomers of fatty acids (FAs), and marketed as SP-2560 and CP-Sil 88. The SLB-IL111 column was operated isothermal at 168°C, with hydrogen as carrier gas at 1.0 mL/min, and the elution profile was characterized using authentic GC standards and synthetic mono-unsaturated fatty acids (MUFAs) and conjugated linoleic acid (CLA) isomers as test mixtures. The SLB-IL111 column provided an improved separation of cis- and trans-18:1 and cis/trans CLA isomers. This is the first direct GC separation of c9,t11- from t7,c9-CLA, and t15-18:1 from c9-18:1, both of which previously required complimentary techniques for their analysis using cyanopropyl siloxane columns. The SLB-IL111 column also provided partial resolution of t13/t14-18:1, c8- from c6/c7-18:1, and for several t,t-CLA isomer pairs. This column also provided elution profiles of the geometric and positional isomers of the 16:1, 20:1 and 18:3 FAMEs that were complementary to those obtained using the cyanopropyl siloxane columns. However, on the SLB-IL111 column the saturated FAs eluted between the cis- and trans MUFAs unlike cyanopropyl siloxane columns that gave a clear separation of most saturated FAs. These differences in elution pattern can be exploited to obtain a more complete analysis of complex lipid mixtures present in ruminant fats.     

Studies on the graft copolymerization of cellulosic materials

Graft copolymers of acrylic acid on cellulosic materials were obtained by use of ceric ion in aqueous medium at various temperatures. The level of incorporation of poly(acrylic acid) grafts and the efficiency of grafting were significantly reduced as the temperature of polymerization was increased from 35° to 60°C. The uptake of cadmium and copperions from aqueous solution by the cellulose-g-poly(acrylic acid) copolymer was examined by equilibrium and dynamic sorption studies. The amount of metal ions removed from solution depended on the metal ion type, initial concentration of the metal ion solution, level of incorporation of poly(acrylic acid) in the graft copolymer and the temperature of the metal ion solution.     

Role of the anion in the underpotential deposition of cadmium on a Rh(111) electrode: probed by voltammetry and in situ scanning tunneling microscopy

In situ scanning tunneling microscopy (STM) and cyclic voltammetry (CV) were employed to examine the underpotential deposition (UPD) of cadmium on a rhodium(111) electrode in sulfuric and hydrochloric acids. The (bi)sulfate and chloride anions in the electrolytes played a main role in controlling the number and arrangement of Cd adatoms. Deposition of Cd along with hydrogen adsorption occurred near 0.1 V (vs reversible hydrogen electrode) in either 0.05 M H2SO4 or 0.1 M HCl containing 1 mM Cd(ClO4)2. These coupled processes resulted in an erroneous coverage of Cd adatoms. The process of Cd deposition shifted positively to 0.3 V and thus separated from that of hydrogen in 0.05 M H2SO4 containing 0.5 M Cd2+. The amount of charge (80 microC/cm2) for Cd deposition in 0.5 M Cd2+ implied a coverage of 0.17 for the Cd adatoms, which agreed with in situ STM results. Regardless of [Cd2+], in situ STM imaging revealed a highly ordered Rh(111)-(6 x 6)-6Cd + HSO4- or SO42- structure in sulfuric acid,. In hydrochloric acid, in situ STM discerned a (2 x 2)-Cd + Cl structure at potentials where Cd deposition commenced. STM atomic resolution showed roughly one-quarter of a monolayer of Cd adatoms were deposited, ca. 50% more than in sulfuric acid. Dynamic in situ STM imaging showed potential dependent, reversible transformations between the (6 x 6) Cd adlattices and (square root 3 x square root 7)-(bi)sulfate structure, and between (2 x 2) and (square root 7 x square root 7)R19.1 degrees -Cl structures. The fact that different Cd structures observed in H2SO4 and HCl entailed the involvement of anions in Cd deposition, i.e. (bi)sulfate and chloride anions were codeposited with Cd adatoms on Rh(111).