Thermal analysis study of Bi<Subscript>2</Subscript>Sr<Subscript>2</Subscript>Ca<Subscript>2</Subscript>Cu<Subscript>3-x</Subscript>Er<Subscript>x</Subscript>O<Subscript>10+δ</Subscript> glass-ceramic system

Summary We have fabricated glasses in the Bi-2223 HT_c superconductor system with Bi₂Sr₂Ca₂Cu_3-xEr_xO_{10+ δ} nominal composition, where x=0.5 and 1.0, by the glass-ceramic technique. Using an analysis developed for non-isothermal crystallization studies, information on some aspects of crystallization temperature and thermal properties has been obtained. The crystallization studies were made using DTA with several uniform rates. The calculations of crystallization activation energies, E_a, and the Avrami parameters, n, were made based on the non-isothermal kinetic theory of Kissinger and the Ozawa’s equations. The DTA data of the samples showed that the first crystallization temperature, T_x1, increases and the second crystallization temperature, T_x2, decreases by increasing the Er concentration. This suggests that the Er substitution had significant effect on the glassification of the BSCCO material due to change on the surface nucleation and increased ionic activities at high temperature region. The activation energy for crystallization, E_a, of the samples was also showed an increase at high Er concentration case. However, the Avrami parameter, n, decreased from 2.5 to 1.7 for x=0.5 and 1.0 samples, respectively. This suggests that the growth mechanism is diffusion-controlled and three-dimensional parabolic growth takes place near the first crystallization temperature. The oxidization rates and the activation barrier for oxygen out-diffusion process, E, was calculated using the TG data. It was found that the total mass gain in the x=0.5 sample is comparably smaller than that of the x=1.0 sample. This shows that the oxygen absorption of the x=1.0 sample is faster than the x=0.5 sample, leading to increase in the oxidization rate in the x=1.0 material.     

Specific heat on Sr<Subscript>2</Subscript>Nb<Subscript>2</Subscript>O<Subscript>7</Subscript> and Sr<Subscript>2</Subscript>Ta<Subscript>2</Subscript>O<Subscript>7</Subscript>

Summary Specific heats on the single crystals of Sr₂Nb₂O₇, Sr₂Ta₂O₇ and (Sr_1-xBa_x)₂Nb₂O₇ were measured in a wide temperature range of 2-600 K. Heat anomalies of a λ-type were observed at the incommensurate phase transition of T_INC (=495 K) on Sr₂Nb₂O₇ and at the super-lattice phase transition of T_SL (=443 K) on Sr₂Ta₂O₇; the transition enthalpies and the transition entropies were estimated. Furthermore, a small heat anomaly was observed at the low temperature ferroelectric phase transition of T_LOW (=95 K) on Sr₂Nb₂O₇. The transition temperature T_LOW decreases with increasing Ba content x and it vanishes for samples of x>2%.     

Formation and properties of the Fe<Subscript>8</Subscript>V<Subscript>10</Subscript>W<Subscript>16–x</Subscript>Mo<Subscript>x</Subscript>O<Subscript>85</Subscript> type solid solution

Solid solution phases of a formula Fe₈V₁₀W_16–xMo_xO₈₅ where 0≤x≤4, have been obtained, possessing a structure of the compound Fe₈V₁₀W₁₆O₈₅. It was found on the base of XRD and DTA investigations that these solution phases melted incongruently, with increasing the value of x, in the temperature range from 1108 (x=0) to 1083 K (x=4) depositing Fe₂WO₆ and WO₃. The increase of the Mo⁶⁺ ions content in the crystal lattice of Fe₈V₁₀W₁₆O₈₅ causes the lattice parameters a=b contraction with cbeing almost constant. IR spectra of the Fe₈V₁₀W_16–xMo_xO₈₅ solid solution phases have been recorded.     

Phase diagram of the system KF-K<Subscript>2</Subscript>TaF<Subscript>7</Subscript>-Ta<Subscript>2</Subscript>O<Subscript>5</Subscript>

As an asymmetric organic molecular crystal, p-N,N-dimethylaminobenzaldehyde (DAB) exhibits peculiar optical property. It was first grown by solution technique adopting slow evaporation method at room temperature using CCl₄ as growth medium. The solubility of DAB increases with temperature. Good quality transparent crystals of p-N,N-dimethylaminobenzaldehyde were carefully collected and subjected various characterization studies such as UV, FTIR, ¹H and ¹³CNMR spectral studies and thermal (TG-DTG) studies to determine the purity and application oriented properties of the grown crystals.     

Thermal behaviour and properties of Na<Subscript>2</Subscript>O-TiO<Subscript>2</Subscript>-P<Subscript>2</Subscript>O<Subscript>5</Subscript> glasses

Differential scanning calorimetry (DSC) and thermomechanical analysis (TMA) were used to study the thermal behaviour of (50-x)Na₂O-xTiO₂-50P₂O₅ and 45Na₂O-yTiO₂-(55-y)P₂O₅ glasses. The addition of TiO₂ to the starting glasses (x=0 and y=5 mol% TiO₂) resulted in a nonlinear increase of glass transition temperature and dilatation softening temperature, whereas the thermal expansion coefficient decreased. All prepared glasses crystallize under heating within the temperature range of 300–610°C. The contribution of the surface crystallization mechanism over the internal one increases with increasing TiO₂ content. With increasing TiO₂ content the temperature of maximum nucleation rate is also gradually shifted from a value close to the glass transition temperature towards the crystallization temperature. X-ray diffraction measurements showed that the major compounds formed by glass crystallization were NaPO₃, TiP₂O₇ and NaTi₂(PO₄)₃. The chemical durability of the glasses without titanium oxide is very poor, but with the replacement of Na₂O or P₂O₅ by TiO₂, it increases sharply.     

Chemical durability of MoO<Subscript>3</Subscript>-P<Subscript>2</Subscript>O<Subscript>5</Subscript> and K<Subscript>2</Subscript>O-MoO<Subscript>3</Subscript>-P<Subscript>2</Subscript>O<Subscript>5</Subscript> glasses

Thermal and chemical durability studies of the phosphate glasses belonging to the binary MoO₃-P₂O₅ and the ternary K₂O-MoO₃-P₂O₅ systems are reported. The chemical resistant attack tests carried out on the free alkaline MoO₃-P₂O₅ glasses show that the glass associated with the P/Mo ratio 2 has the high chemical durability. It shows also a high glass transition temperature value. The above findings are interpreted in terms of the cross-link density of the glasses and the strength of the M-O bonds (M=P, Mo). The influence of K₂O addition on the properties (density, T _g, durability) of this binary high water resistant glass is studied. It is found that the chemical durability along with the other physical properties are reduced by the incroporation of K₂O in the glass matrix. The results were explained by assuming the formation of non-bridging oxygens and weak bonds. The mechanism of the dissolution of these glasses is proposed.     

H<Subscript>6</Subscript>P<Subscript>2</Subscript>W<Subscript>18</Subscript>O<Subscript>62</Subscript>: A green and reusable catalyst for the synthesis of 3,3-diaryloxindole derivatives in water

An efficient and improved procedure for the synthesis of oxindoles derivatives is developed via the electrophilic substitution reaction of indoles with various isatins in the presence of a Wells–Dawson tungsten heteropolyacid in water. Correspondence: Yaghoub Sarrafi, Department of Chemistry, University of Mazandaran, Babolsar, Iran.     

Structure of Zn<Subscript>3</Subscript>P<Subscript>2</Subscript>

The structure of Z_n3P₂ (P 4₂/nmc, a = b = 8. 0785 Å, c = 11. 3966 Å) was solved and refined to R = 3. 2% in a precision X-ray diffraction experiment (λ-MoK _a, graphite monochromator on a primary beam, 27,496 reflections) . Interatomic distances and bond angles have been determined. The fcc lattice of the structure is built from phosphorus atoms, and the zinc atoms occupy 3/4 of all tetrahedral voids; the structure is described by two equivalent models where 1/4 occupied (by zinc atoms) and 1/4 vacant voids change places. The zinc atoms that occupy the voids following the diamond principle do not change places.Original Russian Text Copyright © 2004 by I. E. Zanin, K. B. Aleinikova, M. M. Afanasiev, and M. Yu. Antipin__________Translated from Zhurnal Strukturnoi Khimii, Vol. 45, No. 5, pp. 889–892, September–October, 2004.     

Thermodynamics of Zr<Subscript>52.5</Subscript>Cu<Subscript>17.9</Subscript>Ni<Subscript>14.6</Subscript>Al<Subscript>10</Subscript>Ti<Subscript>5</Subscript> bulk metallic glass forming alloy

Recently, multicomponent glass forming alloys have been found which exhibit extraordinary glass forming ability and cooling rates of less than 100 K/s are sufficient to suppress nucleation of crystalline phases and consequently bulk metallic glass (BMG) is formed. The undercooled melts of BMG systems have high thermal stability in the undercooled region. Therefore, it is interesting to study the thermodynamics of such materials. This article investigates the thermodynamic behavior of a BMG system namely Zr_52.5Cu_17.9Ni_14.6Al₁₀Ti₅ by estimating the Gibbs free energy difference ΔG, entropy difference ΔS, enthalpy difference ΔH between the undercooled liquid and corresponding equilibrium crystalline solid phase, in the entire temperature range from T _m to T _K. Glass forming ability (GFA) of this system has been investigated through various GFA parameters indicating the degree of ease of glass formation.     

The microstructure and magnetic properties of Ni<Subscript>0.4</Subscript>Zn<Subscript>0.6</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript> films prepared by spin-coating method

Nickel zinc ferrite (Ni_0.4Zn_0.6Fe₂O₄) films on Si (100) substrate were synthesized using a spin-coating method. The crystallinity of the Ni_0.4Zn_0.6Fe₂O₄ films with the thickness of about 386 nm became better as the annealing temperature increased. The films have smooth surface, relatively good packing density and uniform thickness. The volatilization of Zn is serious at 900 °C. With the increase of annealing temperature, the saturation magnetization M _s increases in the temperature ranging from 400 to 700 °C, however, decreases above 700 °C, and the coercivity H _c increases in the temperature range 400–800 °C, decreases above 800 °C. After annealed at 700 °C for 2 h in air with the heating rate 2 °C/min, the film shows a maximum saturation magnetization M _s of 349 emu/cc and low coercivity H _c of 66 Oe. The M _s is higher than others which prepared by this method, however, the H _c is lower. The M _s of Ni_0.4Zn_0.6Fe₂O₄ films annealed at 700 °C increases with increasing annealing time and the H _c changes slightly.     

Phase formation in the V<Subscript>2</Subscript>O<Subscript>5</Subscript>-Ta<Subscript>2</Subscript>O<Subscript>5</Subscript>-MoO<Subscript>3</Subscript> system

Solid-phase interactions in the V₂O₅-Ta₂O₅-MoO₃ system were studied. The formation of com- pounds TaVO₅ and VTa₉O₂₅ in the V₂O₅-Ta₂O₅ binary system was verified. Tetragonal VTa₉O₂₅-base solid solutions of the general formula Ta_{5 + 4x} V_{5 − 4x} O₂₅ (x = 0.25–1) and TaVO₅-base solid solutions of the general formula Ta _x Mo_{1 − x} V_{2 − x} O_{8 − 3x} (x = 0.625–1) were found to form. Subsolidus phase equilibria in the V₂O₅-Ta₂O₅-MoO₃ were determined.     

NaBO<Subscript>2</Subscript>-Na<Subscript>2</Subscript>CO<Subscript>3</Subscript>-Na<Subscript>2</Subscript>MoO<Subscript>4</Subscript>-Na<Subscript>2</Subscript>WO<Subscript>4</Subscript> quaternary system

This is the first study of the NaBO₂-Na₂CO₃-Na₂MoO₄-Na₂WO₄ quaternary system by differential thermal analysis. Na₂[MoO_4(x)WO_{4(1 − x)}] solid solutions in the quaternary system are found to not decompose.     

Synthesis of nonequilibrium Ir<Subscript>x</Subscript>Re<Subscript>1-x</Subscript> solid solutions. Crystal structure of [Ir(NH<Subscript>3</Subscript>)<Subscript>5</Subscript>Cl]<Subscript>2</Subscript>[ReCl<Subscript>6</Subscript>]Cl<Subscript>2</Subscript>

Synthesis of five binary complex salts with an [Ir(NH₃)₅Cl]²⁺ complex cation is described. The counterions are [ReCl₆]^2–, [IrCl₆]^2–, [ReBr₆]^2–, and Cl^–. A polycrystal X-ray diffraction study has been performed for [Ir(NH₃)₅Cl]₂[ReCl₆]Cl₂, and its crystal structure has been determined. A series of Ir _x Re_1–x phases (0.5 x > 1) were obtained by reductive thermolysis. For the Ir-Re system, the history of the V/Z(x) dependence has been refined.Original Russian Text Copyright © 2004 by S. A. Gromilov, S. V. Korenev, I. V. Korolkov, K. V. Yusenko, and I. A. BaidinaTranslated from Zhurnal Strukturnoi Khimii, Vol. 45, No. 3, pp. 508–515, May–June 2004.     

Calculations of thermodynamic stability of CpCoC<Subscript>2</Subscript>B<Subscript>9</Subscript>H<Subscript>11</Subscript> cobaltacarborane isomers

Quantum-chemical calculations of the geometry and energies of nine possible isomers of 12-vertex cobaltacarborane CpCoC₂B₉H₁₁ (1) were carried out by the DFT method (PBEPBE/DGDZVP/DGA1). Thermodynamic stability of the isomers increases with increasing distance between the carbon atoms in the cage and is virtually independent of the position of the CpCo vertex. The relative stabilities of the 1,2,3-(17.57 kcal mol⁻¹), 1,2,4-(3.72 kcal mol⁻¹), and 1,2,9-isomers of 1 (0 kcal mol⁻¹) are similar to the corresponding values for the ortho (17.61 kcal mol⁻¹), meta (3.21 kcal mol⁻¹), and para isomers (0 kcal mol⁻¹) of carborane C₂B₁₀H₁₂. The results of the present study confirm a close similarity of the CpCo and BH fragments in metallacarborane chemistry. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 7, pp. 1557–1559, July, 2005.     

Thermochemical properties of MnNb<Subscript>2</Subscript>O<Subscript>6</Subscript>

Homogeneous manganocolumbite (MnNb₂O₆) was synthesized from Nb₂O₅ and MnO oxides. Powder sample was orthorhombic with unit cell parameters: α = 0.5766 nm, b = 1.4439 nm, c = 0.5085 nm and V = 0.4234 nm³. Heat capacity over the temperature range of 313–1253 K was measured in an inert atmosphere with combined thermogravimetry and calorimetry using NETZSCH STA 449C Jupiter thermoanalyzer. Melting point was 1767 ± 3 K, enthalpy of melting was 144 ± 4 kJ mol⁻¹. Experimental heat capacity of MnNb₂O₆ is fitted to polynomial C _pm = 221.46 + 3.03 · 10⁻³ T + −39.79 · 10⁵ T ⁻² + 40.59 · 10⁻⁶ T ².     

Synthesis,structure, and electric properties of oxygen-deficient perovskites Ba<Subscript>3</Subscript>In<Subscript>2</Subscript>ZrO<Subscript>8</Subscript> and Ba<Subscript>4</Subscript>In<Subscript>2</Subscript>Zr<Subscript>2</Subscript>O<Subscript>11</Subscript>

Perovskite phases Ba₃In₂ZrO₈ and Ba₄In₂Zr₂O₁₁ with the nominal concentration of structural oxygen vacancies 1/9 and 1/12, respectively, were synthesized by solid-phase and solution methods. X-ray diffraction showed cubic symmetry of both phases with the unit cell parameter a = 0.4193(2) and 0.4204(3) nm, respectively. The absence of superstructural lines resulted in the conclusion on statistical arrangement of oxygen vacancies. Thermogravimetry and mass spectrometry proved that both phases can reversibly absorb water from gas phase (pH₂O = 2 × 10⁻² atm) with observed correlation between the concentration of oxygen vacancies and amount of absorbed water. The total water amount was up to 0.9 mol per formula unit or, if recalculated for perovskite unit ABO₃, 0.3 and 0.23 mol H₂O, respectively. The temperature curves of coductivity in the atmosphere with various partial water vapor pressures (pH₂O = 3 × 10⁻⁵ and 2 × 10⁻² atm) showed significantly higher conductivity and lower activation energy (0.52 eV) in humid atmosphere due to proton transfer. The proton conductivity is up to 5 × 10⁻⁴ Ohm⁻¹ cm⁻¹ at 300°C for Ba₃In₂ZrO₈ specimen. IR spectrometry showed that protons in the structure exist primarily in OH-groups.     

Preparation and electrical properties of Nd and Mn co-doped Bi<Subscript>4</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> thin films

Ferroelectric thin films of Nd and Mn co-doped bismuth titanate, Bi_3.15Nd_0.85Ti_3−x Mn _x O₁₂ (BNTM) (x = 0–0.1), were fabricated on Pt/TiO₂/SiO₂/Si(100) substrates by a sol–gel technique. The BNTM films had a polycrystalline perovskite structure and uniform and dense surface morphologies. A lattice distortion was observed in the BNTM films due to Mn ion doping. The ferroelectric measurement of the films indicated that the values of coercive field (E _c ) decreased gradually with the increase of the Mn content (x), however, the remanent polarization (P _r ) increase firstly and then decrease with the increase of x. The sample with x = 0.05 had optimum electrical properties and a maximum 2P _r value. The 2P _r and 2E _c values of the film at a maximum applied electric field of 400 kV/cm were 38.3 μC/cm² and 180 kV/cm, respectively. Moreover, this BNTM capacitors did not show fatigue behaviors after 1.0 × 10¹⁰ switching cycles at a frequency of 1 MHz, suggesting a fatigue-free character. The main reason for the increase of the 2P _r and the decrease of the 2E _c might be attributed to the lattice distortion in BNTM films due to Mn ion doping.     

Synthesis of endohedral di-and monometallofullerenes Y<Subscript>2</Subscript>@C<Subscript>84</Subscript>, Ce<Subscript>2</Subscript>@C<Subscript>78</Subscript>, and M@C<Subscript>82</Subscript> (M = Y,Ce)

Endohedral metallofullerenes Y₂@C₈₄, Ce₂@C₇₈, and M@C₈₂ (M = Y, Ce) were synthesized by the electric arc method and isolated from the soot using extraction with o-dichlorobenzene. Pure (98%) endohedral dimetallofullerenes Y₂@C₈₄ and Ce₂@C₇₈ were isolated for the first time from o-dichlorobenzene extracts using HPLC and characterized by mass spectrometry and spectrophotometry. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 11, pp. 2067–2071, November, 2007.     

Whitlockite solid solutions in the Ca<Subscript>3</Subscript>(VO<Subscript>4</Subscript>)<Subscript>2</Subscript>-K<Subscript>3</Subscript>VO<Subscript>4</Subscript>-NdVO<Subscript>4</Subscript> system

Phase equilibria in the Ca₃(VO₄)₂-K₃VO₄-NdVO₄ system have been studied. An extensive calcium orthovanadate-based solid solution was found to form with the boundary compositions as follows: Ca₃(VO₄)₂-Ca₉Nd(VO₄)₇-Ca_9.33K_2.33(VO₄)₇-Ca_7.88K_2.63Nd_0.87(VO₄)₇. The unit cell parameters of the whit-lockite vanadates synthesized increase as the potassium and neodymium contents increase. Phase transitions from the low-temperature β phase to the β′ centrosymmetrical structure in Ca_{9.33 − 5z} K_{2.33 + z} Nd_3z (VO₄)₇ vanadates have been studied dilatometrically. The increase in the β ai β′ transition temperature caused by potassium is interpreted as arising from the filling in of vacant cation positions M(4) and M(6).     

Crystal structure of the synthetic analog of radtkeite Hg<Subscript>3</Subscript>S<Subscript>2</Subscript>Cl<Subscript>1.00</Subscript>I<Subscript>1.00</Subscript>

The results of structural studies of the synthetic analog of the radtkeite mineral Hg₃S₂Cl_1.00I_1.00 are analyzed. The crystal structure of the compound has been refined; the unit cell parameters are a _m = 16.827(4) , b _m = 9.117(1) , c _m = 13.165(5) , = 130.17(2)°, V = 1543.3(8) ³, space group C2/m, Z = 8, R = 0.0527. A possible transition a ₀ = a _m; b ₀ = a _m + 2c _m; c ₀ = –b _m to the pseudo-orthorhombic F cell previously determined for radtkeite, where one of the angles ( ₀ ) is slightly different from 90° (89.55°), has been found. Each sulfur atom in the structure is bonded to three mercury atoms, forming SHg₃ umbrellas with distances 2.240(6) –2.474(8) and angles HgSHg 94.7(2)°–102.9(2)°. The SHg₃ fragments are linked through Hg vertices to form corrugated [Hg₁₂S₈] layers. The halogen atoms lie inside and between the [Hg₁₂S₈] layers; the distances are Hg-Cl and Hg-I 2.783(7) , 2.961(7) , and 3.083(4) –3.311(3) , respectively.Original Russian Text Copyright © 2004 by N. V. Pervukhina, S. V. Borisov, S. A. Magarill, D. Yu. Naumov, V. I. Vasiliev, and B. G. NenashevTranslated from Zhurnal Strukturnoi Khimii, Vol. 45, No. 4, pp. 755–758, July–August, 2004.This revised version was published online in April 2005 with a corrected cover date.