Boron oxide encapsulated Bridgman growth of high-purity high-resistivity cadmium telluride crystals

High-purity semi-insulating CdTe crystals have been successfully grown by encapsulated (B₂O₃) Bridgman technique. The procedure strongly limits component losses allowing the achievement of stoichiometry control material and keeps a low level of impurity contamination as shown by mass spectroscopy analysis data. When strictly stoichiometry-controlled and high-purity polycrystalline source material has been used, high-resistivity crystals have been obtained without any intentional doping. EPD values in the range of 1–3×10⁴ cm⁻² have been observed in a wide region of the crystals. Luminescence spectroscopy confirms the purity and good structural quality of the material. The proposed method avoids the technical problems posed by the High Pressure Bridgman technique and fits the requirements for CdTe/CdZnTe crystals large-scale production.     

Flux growth of PbMg1/3Ta2/3O3 single crystals

Single crystals of PbMg_1/3Ta_2/3O₃ (PMT) were grown by the flux method. The PbO–Pb₃O₄–B₂O₃ system was used as a solvent. Transparent and light yellow PMT single crystals of rectangular shape and dimensions up to 10×6×4 mm³ were obtained. For the applied growth conditions only, the crystals of the perovskite structure were grown. X-ray diffraction tests showed that at room temperature PMT exhibits cubic symmetry with lattice parameter a=4.042(1) Å. Dielectric studies pointed to relaxor properties of PMT. The characteristic broad and frequency-dependent maximum of dielectric permittivity was observed at 179.7 K (1 kHz).     

Oxygen-pressure dependence of the crystallinity of MgO films grown on Si(1 0 0) by PLD

Effects of the oxygen partial pressure on pulsed-laser deposition of MgO buffer layers on silicon substrates were investigated. The overall growth process was monitored in situ by reflection high-energy electron diffraction (RHEED) method. It was found that the crystallinity and surface morphology of the MgO films were strongly affected by oxygen partial pressure in the deposition chamber. The oxygen-pressure dependence could be explained in terms of interactions of oxygen with species in the plume-like plasma. The MgO film obtained at an optimal oxygen-pressure range of 1×10⁻²–1 Pa exhibited an atomic-smooth and defect-free surface (the root-mean-square roughness being as low as 0.82 nm). For the metal–insulator–metal (MIM) structure of Au/MgO (150 nm)/TiN prepared at the optimal growth conditions achieved a very low leak current density of 10⁻⁷ A cm⁻² at an electric field of 8×10⁵ V cm⁻¹ and the permittivity (ε_r) of about 10.6, virtually the same as that of the bulk MgO single crystals.     

Flux growth of BPO4 crystals

Single crystals of BPO₄ with sizes up to 15×10×12 mm³ were grown by top-seeded solution growth method using Li₂O–Li₄P₂O₇ as fluxes. The components volatilized from the melt were characterized by the method of X-ray powder diffraction. The defects of grown crystals have also been investigated. The measured ultraviolet cutoff edge of BPO₄ was about 130 nm. Its density was 2.82 g/cm³ determined using drainage method.     

Growth and spectral properties of Nd:LaVO4 crystal

This paper reports the growth and spectral properties of 3.5 at% Nd³⁺:LaVO₄ crystal with diameter of 20×15 mm² which has been grown by the Czochralski method. The spectral parameters were calculated based on Judd–Ofelt theory. The intensity parameters Ω_λ are: Ω₂=2.102×10⁻²⁰ cm², Ω₄=3.871×10⁻²⁰ cm², Ω₆=3.235×10⁻²⁰ cm². The radiative lifetime τ_r is 209 μs and calculated fluorescence branch ratios are: β₁(0.88μm)=45.2, β₂(1.06μm)=46.7, β₃(1.34μm)=8.1. The measured fluorescence lifetime τ_f is 137 μm and the quantum efficiency η is 65.6%. The absorption band at 808 nm wavelength has an FWHM of 20 nm. The absorption and emission cross sections are 3×10⁻²⁰ and 6.13×10⁻²⁰ cm², respectively.     

Improved growth of PbI2 single crystals

The phase equilibrium and the crystallization process of lead iodide (PbI₂) melt have been primarily investigated according to the lead–iodine phase diagram. It is found that the iodine evaporation and the segregated lead deposition are the two important factors that affect the PbI₂ crystal quality. The new method of Pulling U-type quartz growth ampoule has been made to impede the decomposition of PbI₂ and the vaporization and condensation of iodine. An orange and translucent PbI₂ single crystal of large size was obtained by the improved growth method, i.e. U-type ampoule pulling. Resistivity of the as-grown crystal is up to 4×10¹¹ Ω cm, and IR transmission is up to 45% in the region from 7800 to 450 cm⁻¹. Therefore, the improved growth method is a promising convenient new method for the growth of high quality PbI₂ crystals.     

Efficiency optimization of p-type doping in GaN:Mg layers grown by molecular-beam epitaxy

The Mg-doping efficiency in GaN layers grown by molecular-beam epitaxy has been studied as a function of the growth temperature, the growth rate, and the Mg beam flux. The Mg cell temperature window for efficient p-type doping is rather narrow, being limited by the GaN n-type background doping density (lower limit) and by the Mg surface coverage that, beyond a threshold, induces a layer polarity inversion (N-polarity), leading to a reduction of the Mg incorporation (upper limit). An increase of the growth temperature avoids this polarity inversion, but the Mg flux must be increased to compensate the strong desorption rate. Thus, a trade-off between both temperatures has to be reached. A reduction of the growth rate has a strong effect on the p-type doping level, yielding up to 7×10¹⁷ holes/cm³ for a total Mg concentration of 1×10¹⁹ cm⁻³. This high Mg concentration does not seem to generate Mg-related defects or deep traps.     

Ambient-condition growth of superconducting YBa2Cu4O8 single crystals using KOH flux

YBa₂Cu₄O₈ is a stoichiometric oxide superconductor of T_c80 K. Unlike YBa₂Cu₃O_7−δ, this compound is free from oxygen vacancy or twin formation and does not have any microscopic disorder in the crystal. Doping with Ca raises its T_c to 90 K. The compound is a promising superconductor for technological application. Up to now, single crystals have not been grown without using specialized apparatus with extremely high oxygen pressure up to 3000 bar and at over 1100 °C due to the limited range of reaction kinetics of the compound. This fact has delayed the progress in the study of its physical properties and potential applications. We present here a simple growth method using KOH as flux that acts effectively for obtaining high-quality single crystals in air/oxygen at the temperature as low as 550 °C. As-grown crystals can readily be separated from the flux and exhibit a perfect orthorhombic morphology with sizes up to 0.7×0.4×0.2 mm³. Our results are reproducible and suggest that the crystals can be grown using a conventional flux method under ambient condition.     

High-temperature growth of very high germanium content SiGe virtual substrates

We have first of all studied (in reduced pressure–chemical vapour deposition) the high-temperature growth kinetics of SiGe in the 0–100% Ge concentration range. We have then grown very high Ge content (55–100%) SiGe virtual substrates at 850 °C. We have focused on the impact of the final Ge concentration on the SiGe virtual substrates’ structural properties. Polished Si_0.5Ge_0.5 virtual substrates were used as templates for the growth of the high Ge concentration part of such stacks, in order to minimize the severe surface roughening occurring when ramping up the Ge concentration. The macroscopic degree of strain relaxation increases from 99% up to values close to 104% as the Ge concentration of our SiGe virtual substrates increases from 50% up to 100% (discrepancies in-between the thermal expansion coefficients of Si and SiGe). The surface root mean square roughness increases when the Ge concentration increases, reaching values close to 20 nm for 100% of Ge. Finally, the field (the pile-up) threading dislocations density (TDD) decreases as the Ge concentration increases, from 4×10⁵ cm⁻² (1–2×10⁵ cm⁻²) for [Ge]=50% down to slightly more than 1×10⁵ cm⁻² (a few 10⁴ cm⁻²) for [Ge]=88%. For [Ge]=100%, the field TDD is of the order of 3×10⁶ cm⁻², however.     

Growth and spectral properties of Nd-doped Sr3Y(BO3)3 crystal

A new crystal of Nd³⁺:Sr₃Y(BO₃)₃ with dimension up to 25×35 mm² was grown by Czochralski method. Absorption and emission spectra of Nd³⁺: Sr₃Y(BO₃)₃ were investigated . The absorption band at 807 nm has a FWHM of 18 nm. The absorption and emission cross sections are 2.17×10⁻²⁰ cm² at 807 nm and 1.88×10⁻¹⁹ cm² at 1060 nm, respectively. The luminescence lifetime τ_f is 73 μs at room temperature     

Defect characterization and composition distributions of mercury indium telluride single crystals

A mercury indium telluride (MIT) ingot was grown by the vertical Bridgman method. The defects in MIT crystals were characterized by the chemical etching method. A defect etchant for MIT crystals was developed. The etch pits of dislocations, microcracks and boundary was observed by scanning electron microscopy. It was elucidated that the etch pits density of dislocations of MIT wafers was about 4×10⁵ cm⁻². Te and In reduced at the grain boundaries, but were homogeneously distributed within the grains in the as-grown MIT crystals. The distribution of In in MIT crystals along the growth direction and radial direction was analyzed by electronic probe microscopy. It was found that In concentration was higher in the initial part and lower in the final part of the MIT ingot, which indicated that the segregation coefficient of In in MIT crystals was 1.15. The radial In concentration increased from the center to edge of the wafers and homogeneous in the middle part.     

Growth and characterization of a new nonlinear optical material: Potassium p-nitrophenolate dihydrate (NO2–C6H4–OK·2H2O) with new bonding properties

Single crystals of potassium p-nitrophenolate dihydrate (NPK·2H₂O) have been grown successfully using the isothermal solvent evaporation technique. It is a new semiorganic nonlinear optical crystal, possessing a d_eff of about 1.5 times that of lithium niobate and in which the K⁺ ions are bonded to the nitro group instead of bonding with the phenolic O⁻. Large single crystals of dimension upto 20×6×4 mm³ are harvested within a period of 60 days. The grown crystals are subjected to single crystal X-ray, FTIR and DRS-UV visible spectral, thermal and microhardness analyses. Single crystal X-ray analysis confirms the molecular formula and the structure of the crystal. FTIR spectral studies verify the functional groups present in the crystal. The DRS-UV visible spectrum proved the optical transparency of the crystal in the entire visible and near infrared region. Thermal studies reveal that the crystals are stable upto 180 °C. Microhardness measurements on the cleaved plane (1 1 0) explain the strength and slip direction in the crystal. The SHG efficiency of the crystal is examined by performing the Kurtz powder test using Nd:YAG laser.     

Investigations on the effect of InSb and InAsSb step-graded buffer layers in InAs0.5Sb0.5 epilayers grown on GaAs (0 0 1)

We report the structural and electrical properties of InAsSb epilayers grown on GaAs (0 0 1) substrates with mid-alloy composition of 0.5. InSb buffer layer and InAs_xSb_1−x step-graded (SG) buffer layer have been used to relax lattice mismatch between the epilayer and substrate. A decrease in the full-width at half-maximum (FWHM) of the epilayer is observed with increasing the thickness of the InSb buffer layer. The surface morphology of the epilayer is found to change from 3D island growth to 2D growth and the electron mobility of the sample is increased from 5.2×10³ to 1.1×10⁴ cm²/V s by increasing the thickness of the SG layers. These results suggest that high crystalline quality and electron mobility of the InAs_0.5Sb_0.5 alloy can be achieved by the growth of thick SG InAsSb buffer layer accompanied with a thick InSb buffer layer. We have confirmed the improvement in the structural and electrical properties of the InAs_0.5Sb_0.5 epilayer by quantitative analysis of the epilayer having a 2.09 μm thick InSb buffer layer and 0.6 μm thickness of each SG layers.     

X-ray characterization of detached-grown germanium crystals

Germanium (1 1 1)-oriented crystals have been grown by the vertical Bridgman technique, in both detached and attached configurations. Microstructural characterization of these crystals has been performed using synchrotron white beam X-ray topography (SWBXT) and double axis X-ray diffraction. Dislocation densities were measured from X-ray topographs obtained using the reflection geometry. For detached-grown crystals, the dislocation density is on the order of 10⁴ cm⁻² in the seed region, and decreases in the direction of growth to less than 10³ cm⁻², and in some crystals reaches less than 10² cm⁻². For crystals grown in the attached configuration, dislocation densities were on the order of 10⁴ cm⁻² in the middle of the crystals, increasing to greater than 10⁵ cm⁻² near the edge. The measured dislocation densities are in excellent agreement with etch pit density (EPD) results. Broadening and splitting of the rocking curve linewidths was observed in the vicinity of subgrain boundaries identified by X-ray topography in some of the attached-grown crystal wafers. The spatial distribution of rocking curve linewidths across the wafers corresponds to the spatial distribution of defect densities measured in the X-ray topographs and EPD micrographs.     

Metastable PbO crystal grown through alcohol-thermal process

An alcohol-thermal route has been developed to the growth of single crystals of yellow metastable PbO in largest dimensions of 11×1×0.1 mm³, using freshly synthesized β-PbO crystallites as seeds. The transformation of metastable β-PbO to stable form (-PbO) can be slowed down by choosing appropriate solvent as the growth medium. The obtained β-PbO crystals have a strong orientational growth parallel to the (0 0 1) plane and exhibit a lath shape. Studies found that cooling rate and NaOH concentration also have great influence on the crystallographic forms of the final products during the alcohol-thermal process.     

Polarization induced 2D hole gas in GaN/AlGaN heterostructures

The generation of high density 2D hole gases is crucial for further progress in the electronic and optoelectronic nitride devices. In this paper, we present systematic theoretical studies of Mg-doped GaN/AlGaN gated heterostructures and superlattices. Our calculations are based on a self-consistent solution of the multiband k.p Schrödinger and Poisson equation and reveal that the hole 2D sheet density is mainly determined by the polarization induced interface charges. For an aluminium concentration of 30%, the induced hole density in the heterostructure can reach values up to 1.5×10¹³ cm⁻². In the GaN/AlGaN superlattices, the hole sheet density increases with the superlattice period and saturates for a period of 40 nm at a value of 1.5×10¹³ cm⁻².     

Growth and characterization of epitaxial layers on aluminum nitride substrates prepared from bulk, single crystals

A comparative study of epitaxy of AlN, GaN and their alloys, grown on c-axis and off-axis substrates of single-crystal aluminum nitride has been carried out. Growth on off-axis (>30°) substrates appears to result in rough surfaces and the absence of two-dimensional electron gas (2DEG). However, smooth morphologies were demonstrated for both homoepitaxial and heteroepitaxial growth on on-axis (<2°) substrates. On one of these oriented substrates a 2DEG, with a mobility of 1000 cm²/V s and a sheet density of 8.5×10¹² cm⁻² at room temperature, was also demonstrated for the first time.     

Hydroxyapatite crystallization in the presence of acetaminophen

The effect of acetaminophen; a widely used analgesic and fever reducing medicine; in supersaturated solutions of calcium phosphate was investigated under plethostatic conditions, at 37 °C, 0.15 M NaCl, pH 7.40. The rates of crystal growth measured in the presence of acetaminophen 1.654×10⁻⁴ mol dm⁻³ to 6.616×10⁻⁴ mol dm⁻³ were reduced by 43% to 79%, respectively. The inhibition effect on the crystal growth rate may be explained through adsorption onto the active growth sites. Kinetic analysis suggested Langmuir-type adsorption of acetaminophen on the HAP surface with a affinity value of 2.4×10⁻⁴ dm³ mol⁻¹, for the substrate in the concentration range investigated. The electrophoretic mobility measurements showed that in the presence of acetaminophen the charge of the acetaminophen covered HAP particles was shifted to more negative values as compared to bare HAP. In the presence of acetaminophen no changes observed in the HAP overgrown morphology or in the apparent order of crystallization.     

Structure and optical properties of self-assembled InAs/GaAs quantum dots with In0.15Ga0.85As underlying layer

A high density of 1.02×10¹¹ cm⁻² of InAs islands with In_0.15Ga_0.85As underlying layer has been achieved on GaAs (1 0 0) substrate by solid source molecular beam epitaxy. Atomic force microscopy and PL spectra show the size evolution of InAs islands. A 1.3 μm photoluminescence (PL) from InAs islands with In_0.15Ga_0.85As underlying layer and InGaAs strain-reduced layer has been obtained. Our results provide important information for optimizing the epitaxial structures of 1.3 μm wavelength quantum dots devices.     

Growth and characterization of CdSe single crystals by modified vertical vapor phase method

Good quality, large single crystals of CdSe were grown by the modified growth method (i.e., vertical unseeded vapor phase growth with multi-step purification of the starting material in the same quartz ampoule without any manual transfer between the steps). Lower temperature gradients (8–9°C/cm) at the growth interface were used for the crystal growth. As-grown CdSe crystals was characterized by X-ray diffraction, scanning electron microscopy, energy dispersive analyzer of X-rays, high-resistance instrument measurement, and etch-pit observation. It is found that there are two cleavage faces of (1 0 0) and (1 1 0) orientations on the crystal, the resistivity is about 10⁸ Ω cm, and the density of etch pits is about 10^3–4/cm². The crystal was cut into wafers and was fabricated into detectors. The detectors were tested using an ²⁴¹Am radiation source. γ-ray spectra at 59.5 keV were obtained. The results demonstrated that the quality of the as-grown crystals was good. The crystals were useful for fabrication of room-temperature-operating nuclear radiation detectors. Therefore, the modified growth technique is a promising, convenient, new method for the growth of high-quality CdSe single crystals.