Simultaneous determination of neodymium and erbium in rare earth mixture with 5,7-dibromo-8-hydroxyquinoline and TX-100 by third-derivative spectrophotometry

The absorption spectra of 4f electron transitions of the complexes of neodymium and erbium with 5,7-dibromo-8-hydroxyquinoline in the presence of octylphenol poly(ethyleneglycol)ether have been studied by normal and third-derivative spectrophotometry. The proposed method is free of interference of other rare earths. The calibration graphs were linear up to 18 g/ml of neodymium and 21 g/ml of erbium (in the final solution). The derivative molar absorptivities are 395 l.mol^–1.cm^–1 for neodymium and 3421.mol^–1.cm^–1 for erbium. The corresponding values of Sandell's sensitivity were 0.36 and 0.49 g.cm^–1, respectively. The relative standard deviations evaluated from ten independent determinations of 2.5 g/ml of neodymium and erbium are 1.5 and 3.8% for neodymium and 1.8 and 4.1% for erbium in absence and presence of 70 g of lanthanum, respectively. The detection limits (signal to noise ratio=2) are 0.23 g/ml for neodymium and 0.30 g/ml for erbium. The method has been used for the determination of neodymium and erbium in mixed rare earths with satisfactory results.     

Determination of nitrogen in uranium and uranium-oxide by high-temperature gas-extraction

Summary The reducing fusion gas extraction method has been used for the determination of nitrogen in uranium metal and uranium dioxide reference materials at levels of about 10–15g·g^–1. It has been found that when extracting at temperatures above 2700° C the use of a platinum flux is no longer necessary. Pure nitrogen and nitrogen-helium mixtures were used for calibrating the detection unit in the range of 1.5–670 g. The calibration of the extraction was performed with metallic reference materials in the range of 8–331 g N₂ content.

---

Bestimmung von Stickstoff in Uran und Uranoxid durch Hochtemperatur-Gasextraktion

Zusammenfassung Die Gasextraktion aus reduzierender Schmelze wurde zur Stickstoffbestimmung in Uranmetall- und Urandioxid-Referenzmaterialien bei Gehalten von 10–15 g·g^–1 angewendet. Bei Temperaturen über 2700° C ist kein Platinbad mehr erforderlich. Zur Eichung der Detektionseinheit im Bereich von 1,5–670 g wurden reiner Stickstoff oder Stickstoff-Helium-Mischungen benutzt. Zur Eichung der Extraktion wurden metallische Referenzmaterialien mit (8–331g) N₂ eingesetzt.

     

Application of l-cysteine-capped nano-ZnS as a fluorescence probe for the determination of proteins

Nanometer-sized l-cysteine-capped ZnS particles have been synthesized and used as a fluorescence probe to investigate the effect of proteins on fluorescent intensity. With =190 nm, maximum and constant synchronous fluorescence enhancement was produced at 267 nm and pH 5.12 in the presence of proteins. A highly sensitive synchronous fluorescence method for the rapid determination of proteins has been developed. Under optimum conditions, calibration graphs are linear over the range 0.03–8.0 g mL^–1 for bovine serum albumin (BSA), 0.01–6.0 g mL^–1 for human serum albumin (HSA), 0.05–8.0 g mL^–1 for -globulin (-G), and 0.04–4.0 g mL^–1 for ovalbumin, respectively. The relative standard deviations of seven replicate measurements were 1.75% for 1.0 g mL^–1 BSA, 1.90% for 1.0 g mL^–1 HSA, 1.65% for 1.0 g mL^–1 -G, and 2.32% for 1.0 g mL^–1 ovalbumin.     

A toxic reagent-free method for normal-phase matrix solid-phase dispersion extraction and reversed-phase liquid chromatographic determination of aldrin,dieldrin, and DDTs in animal fats

A method for the determination of aldrin, dieldrin, DDT, DDE, and DDD contamination in animal fats (beef tallow, lard, and chicken fat) without using toxic reagents is developed, that uses high-performance liquid chromatography after the sample has been prepared by matrix solid-phase dispersion (MSPD) with acidic alumina oxide. A reversed-phase C₁-silica column with a mobile phase of 50% (v/v) ethanol solution (in water) and a photo-diode array detector were used for the determination. Average recoveries of the target compounds (0.2–5.0 g g^–1) ranged from 84–98%, with coefficients of variation of <5%. The limits of quantitation were 0.16 g g^–1 for AD, 0.10 g g^–1 for DD, 0.06 g g^–1 for DDT, 0.07 g g^–1 for DDE, and 0.05 g g^–1 for DDD. No toxic reagents were used at all.     

Spectrophotometric determination of 6-aminopenicillanic acid using bromophenol blue and bromothymol blue

Two simple, selective and sensitive spectrophotometric methods are described for the determination of 6-aminopenicillanic acid (6-APA). The methods are based on the reaction of 6-APA with either bromophenol blue (BPB) or bromothymol blue (BTB), to give orange-red and green species, respectively. The coloured products are quantified spectrophotometrically at 625 and 616 nm for BPB and BTB, respectively. The optimization of the different experimental conditions is described. No interferences from different -lactams and common degradation products were observed in the determination of 6-APA using BTB, while flucloxacillin, dicloxacillin, adrenaline, vitamin C, urea and common degradation products in any percentage interfere on using BPB only. The BTB method was better than the BPB method, because of its wider range of determination (0.4–20 g ml^–1 vs. 0.4–7.2 g ml^–1 on using BPB), higher molar absorptivity and Sandell sensitivity (3.27 × 10³l mol^–1 cm^–1 and 0.099 g cm^–2 vs. 2.82 × 10³lmol^–1 cm^–1 and 0.115 g cm^–2), greater stability (3 and 10 days on using BTB and BPB, respectively) and better selectivity. The results were compared with those given by the Official United States Pharmacopeial XXI method.     

Nuclear interferences of uranium and thorium in a reactor neutron activation analysis determination of cerium using the radionuclides141Ce and143Ce

The interference contributions of uranium and thorium to the determination of cerium based on radionuclides¹⁴¹Ce and¹⁴³Ce produced by irradiation in a reactor core was determined. The values of the interference contributions for¹⁴¹Ce were 0.28±0.01 g Ce/g U and /2.01±0.05/x10^–3 g Ce/g Th, and for¹⁴³Ce 1.33±0.03 g Ce/g U and /9.0±0.2/x10^–3 g Ce/g Th.     

Elements in car and truck tires and their volatilization upon incineration

The trace metal loading of used car and truck tires and the fractions of the metals volatilized upon incineration of the tire were determined. INAA was chosen due to its multielement analysis capability and its low detection limit for many elements. A high purity planar germanium detector was used. Among the elements measured were, Al (4–150 g/g), Ti (41–730 g/g), V (0.04–0.4g/g), Mg (>80–580 g/g), Zn (1–2.2%) as typical concentrations; also some amounts of antimony, bromine and arsenic have been found. Major differences in elemental concentrations have been observed between the tread and the wall of a tire, and also between different brands.     

Rapid analysis of pyrethroids in whole urine by high-performance liquid chromatography using a monolithic column and off-line preconcentration in a restricted access material cartridge

A rapid high-performance liquid chromatography (HPLC) method using a monolithic column with UV detection at 238 nm was developed for the determination of fenpropathrin, betacyfluthrin, deltamethrin, and permethrin (cis and trans isomers) in whole urine. The method is based on the use of a monolithic chromatographic column and a restricted access material (RAM) cartridge for sample preparation. The mobile phase was water/acetonitrile (42:58 v/v), the flow rate was 3 mL min^–1, and chromatographic separation was carried out in 10 min. The separation of cis and trans isomers of permethrin was also possible under the above-mentioned conditions. Detection limits in reconstituted whole urine samples were between 0.9 g L^–1 for betacyfluthrin and 4.4 g L^–1 for fenpropathrin and trans-permethrin. Recoveries for urine samples spiked with different amounts of pyrethroids (between 19 g L^–1 and 75 g L^–1) were in the 70±6 to 90±7% range.     

Determination of traces of sodium alkylbenzenesulphonate by high-performance liquid chromatography. Application to water

Summary For the trace determination of sodium alkylbenzenesulphonate (ABS) by HPLC the following conditions were employed: Shimadzu ZORBAX SIL Column (5 m, 4.6 mm i.d. x 150 mm) as stationary phase, 0.2% ammoniaethanol (v/v) as mobile phase, UV detector at 225 nm, injection volume 12 l. The chromatograms of ABS were simple and sharp (detection limit of ABS 0.02 g in 12 l of ethanol). The calibration curves of ABS were linear in a concentration range of 0.03 0.3 g in 12 l of ethanol. In the case of linear sodium dodecylbenzenesulphonate positive errors of 1 4% were caused by non-ionic surfactants or laurylsulphate (6 times excess), 10 50% positive errors were caused by 2 6 times excess of household detergents.Standard water samples containing ABS were treated with a weak base anion-exchange resin, the adsorbed ABS were eluted, and then determined either by HPLC or by the methylene blue spectrophotometric method. Recoveries of ABS in water were about 92 107% by HPLC.

---

Bestimmung von Spuren Natriumalkylbenzolsulfonat mit Hilfe der HPLC. Anwendung auf Wasser

Zusammenfassung Für die Spurenbestimmung von Natriumalkylbenzolsulfonat (ABS) durch HPLC werden die folgenden Bedingungen empfohlen:Shimadzu ZORBAX SIL (5 m, 4,6 mm x 150 mm) als stationäre Phase, 0,2% Ammoniak/Ethanol als mobile Phase, UV-Detektor bei 225 nm, Injektionsvolumen 12 l. Die erhaltenen Chromatogramme sind einfach und scharf (Nachweisgrenze 0,02 g in 12 ml Ethanol). Die Eichkurven sind im Konzentrationsbereich von 0,03–0,3 g in 12 l Ethanol linear. Im Falle des linearen Natriumdodecylbenzolsulfonats werden bei Anwesenheit von nicht-ionischen oberflächenaktiven Substanzen oder von Laurylsulfat in 6fachem Überschuß positiver Fehler von 1–4% erhalten; bei 2–6fachem Überschuß von Haushaltswaschmitteln ergeben sich positive Fehler von 10–50%.Standard-Wasserproben werden zunächst einer Behandlung mit einem Anionenaustauscher unterzogen, die adsorbierten ABS eluiert und durch HPLC oder nach der Methylenblaumethode analysiert. Wiederfindungsraten liegen bei 92–107%.

     

Fällungsanalyse im Mikrogrammbereich: Eine neue Methode

Zusammenfassung Eine neue Methode zur Durchführung gravimetrischer Bestimmungen im Mikrogrammbereich wurde beschrieben; diese beruht im wesentlichen darauf, daß der Niederschlag nicht mehr zusammen mit dem Filter, sondern nach Überführen mit einem geeigneten Lösungsmittel in einem separaten Wägegefäß gewogen wird.Die dazu nötigen Geräte und deren Herstellung wurden beschrieben. Nach dieser Methode wurden folgende Bestimmungen mit zufriedenstellender Richtigkeit durchgeführt: 2,5–25g Al, 5–50g Cu und 5–50g Zn mit Oxin, 2,5–25g Fe(III) und 2,5–25g Ti(IV) mit N-Benzoyl-phenylhydroxylamin, 5–50g Ni und 5–50g Cu mit Salicylaldoxim, 2,5–50g Co(II) und 2,5–50g Fe(III) mit -Nitroso--naphthol sowie 5–50g Chlorid als Silberchlorid.

---

Precipitation analysis in the microgram-scale: A new method

Summary A new method for gravimetric determinations in the microgram-scale is described. This method is based on the fact that the precipitate is not weighed together with the filter but is transferred to a separate weighingvessel using a suitable solvent. The necessary simple devices and their use are described. The following determinations were carried out with satisfying accuracy: 2,5–25g Al, 5–50g Cu and 5–50g Zn with Oxine, 2,5–25g Fe and 2,5–25g Ti withN-benzoylphenylhydroxylamine, 5–50g Ni and 5–50g Cu with salicylaldoxime, 2,52–50g Co and 2,5–50g Fe with -nitroso--naphthol and 5–50g chloride as silver chloride.

     

Analysis of the fusariotoxins zearalenone and vomitoxin (deoxynivalenol) in human foods and animal feeds by high-performance liquid chromatography (HPLC)

Summary HPLC procedures for analyses of the fusariotoxins zearalenone and vomitoxin in individual food- and feedstuffs as well as in mixed feed are described. Zearalenone is separated on a column with polar stationary phase (25 cm × 4.6 mm i.d., particle size 7 m), eluted with a chloroform-isooctane (75/25, v/v)+1.5% methanol mixture and detected fluorometrically. The quantitative determination was possible in all analyzed samples with a detection limit of 2g/kg with 70–80% recovery. Vomitoxin is fractionated by HPLC (C ₁₈ ¹ column, 25 cm×4 mm i.d., 5 m particle size) with water-methanol (60/40, v/v) mobile phase and determined by combining GLC or TLC with UV detection. The detection limit in mixed feed with interfering substances was 25 g/kg (recovery 25–35%). The separation by HPLC makes preparation of pure vomitoxin possible. The described methods are fast, simple and low cost and are suitable for routine analyses.     

Polarographische Bestimmung von ?thylen-bis-thiurammonosulfid

Zusammenfassung Das polarographische Verhalten von Äthylen-bis-thiurammonosulfid, das als fungitoxisches Abbauprodukt der Pflanzenschutzmittel Maneb, Zineb und Nabam auftritt, wird beschrieben. Zur Bestimmung wird M Acetatpuffer pH 4,7 als Grundlösung empfohlen. Es erscheint eine gut ausgebildete Reduktionsstufe mit dem Halbstufen potential –1,085 V (GKE). Die untere Bestimmungsgrenze liegt bei etwa 0,5 g/ml. Bei Anwendung der Impulsmethode (single-sweep-Technik) lassen sich in 0,8 N HCl noch 0,05 g/ml bestimmen.

---

Polarographic determination of ethylene-bis-thiuram-monosulphide

The polarographic properties of ethylene-bis thiuram-monosulphide, a fungitoxic degradation product of the fungicides Maneb, Zineb, and Nabani have been described. For analytical purposes the recommended supporting electrolyte is M acetate buffer (pH 4,7) in which a well-defined reduction wave is produced at a half wave potential of –1.085 V (SCE). The lower limit of detection is near 0.5 g/ml for classical DC-polarography whereas it is still possible to determine 0.05 g/ml 0.8 N HCl using the single sweep method.

     

Thermo-Gasanalysator zur Charakterisierung von Kohlenstoff- und Schwefelverbindungen in luftgetragenen St?uben

Zusammenfassung Die Charakterisierung von Kohlenstoff- und Schwefelverbindungen in korngrößenseparierend gesammelten Staubproben wird durch temperaturprogrammierte Zersetzung der Probe im Sauerstoffstrom und simultane Analyse von gebildetem CO₂ und SO₂ durchgeführt. Eine Unterscheidung von zwei organischen Kohlenstofffraktionen sowie von »Ruß-Kohlenstoff«, »Carbonatkohlenstoff«, »Konversionsschwefel«, »Ruß-Schwefel« und »Schwefel aus thermisch stabilen Sulfaten« in vier Korngrößenbereichen im Staubkollektiv 0,1–25 m AD ermöglicht die Zuordnung bestimmter Verbindungsgruppen zu verschiedenenen Bereichen des »Multimodalen Modells«. Zur Analyse werden 50–200 g Probe benötigt. Der Analysator besteht aus der Kombination eines temperaturprogrammierten Ofens mit gasanalytischen Monitoren für CO₂ und SO₂. Die Nachweisempfindlichkeit liegt bei 40 ng S s^–1 und 400 ng C s^–1 für vollen Schreiberausschlag (200 mm). In Anwendungsbeispielen wird der Einsatz der Methode zur Quellenanalyse von Aerosolen demonstriert.

---

Thermo gas-analyzer for the characterization of carbonaceous and sulphurous compounds in atmospheric particles

Summary Characterization of carbonaceous and sulphurous compounds in size fractions of atmospheric particles is carried out by temperature programmed decomposition of the sample in oxygen atmosphere and simultaneous detection of evolved CO₂ and SO₂. The speciation of two organic carbon fractions, of soot carbon, carbonate carbon, converted sulphur, soot sulphur and sulphur from thermally stable sulphates in four size ranges of atmospheric particles (0.1–25 m AD) makes possible the classification into modes according to the multimodal model. For the analysis 50–200 g of sample is required. The analyzer, a combination of a temperature programmed furnace with instruments for monitoring of CO₂ and SO₂ is operated with a sensitivity of 40 ng S s^–1 and 400 ng Cs^–1 for recorder full-scale (200mm). Results of field tests demonstrate the application for aerosol source identification and conversion studies.

Der Autor möchte Herrn Prof. Dr. H. Malissa für die Anregungen und Diskussionen zur vorliegenden Arbeit vielmals danken. Mein Dank gilt auch Frl. Ing. Ch. Minich für die technische Assistenz bei der Durchführung der Analysen.Diese Arbeit wurde durch Mittel und Geräte des Bundesministeriums für Gesundheit und Umweltschutz unterstützt.     

Simultaneous determination of arsenic and selenium in biological samples by HG-AFS

A new method is proposed for simultaneous determination of traces of arsenic (As) and selenium (Se) in biological samples by hydride-generation double-channel non-dispersive atomic-fluorescence spectrometry (HG-AFS) from tartaric acid media. The effects of analytical conditions on fluorescence signal intensity were investigated and optimized. Interferences from coexisting ions were evaluated. Under optimum conditions linear response ranges above 20 g L^–1 for As and 32 g L^–1 for Se were obtained with detection limits of 0.13 and 0.12 g L^–1, respectively. The precision for elevenfold determination of As at the 4 g L^–1 level and of Se at the 8 g L^–1 level were 2.7 and 1.9% (RSD), respectively. Recoveries of 92.5–95.5% for As and 101.2–108.4% for Se were obtained for four biological samples and two certified biological reference materials. The proposed method has the advantages of simple operation, high sensitivity, and high efficiency; it was successfully used for simultaneous determination of As and Se in biological samples.     

Analysis of organobromine compounds and HBr in motor car exhaust gases with a GC/microwave plasma system

Summary In this investigation an analytical procedure for the determination of different organobromine compounds in motor car exhaust gases is developed in order to obtain a total balance of these compounds in this type of exhaust gas. For this purpose, adsorption sampling on Tenax GC combined with thermal desorption and a fast cold trap injection into the GC column system is used. A special capillary cold trap/thermodesorption system for a fast injection within 1 s is developed. The chromatographically separated fractions are identified by their retention times and elementspecific detection with a microwave plasma detector. Methyl bromide, 1,2-dibromoethane, and vinyl bromide are analysed in exhaust gases in cases where the gasoline contains 1,2-dibromoethane as an additive (leaded gasoline). The analysed bromine contents, which correspond to these organobromine compounds, are in the range of 90–190 g/m³, 15–85 g/m³, and 5–20 g/m³, respectively. The portion of the organobromine compounds is 22–44% of the total bromine which is emitted by the exhaust gases. The other portion contains mainly inorganic particulate bromide, which can be separated by filters. The concentration of the organobromine compounds decreases with increasing motor temperature. After conversion into 2-bromocyclohexanol and after gas chromatographic separation HBr is detected to be 5.8 g bromine per m³ exhaust gas, which corresponds to approximately 1% of the total bromine emission. 1,2-Dichloroethane is analysed in the range of 5–35 g Cl/m³, whereas the concentration of tetraalkyl lead in the exhaust gases is less than the detection limit of 6.7 g Pb/m³. The average bromine/lead ratio found in the filterable portion of the exhaust gases is 0.30 (by weight); the same ratio calculated for total bromine emission including the organobromine compounds is 0.47. Compared with the bromine/ lead ratio in gasoline of 0.39 this means that at least 17% of the total lead in the gasoline is not directly emitted with the motor car exhaust gases.

---

Analyse von bromorganischen Verbindungen und HBr in Autoabgasen mit einem GC/Mikrowellenplasma-System

     

Synthesis and protonation of an OS3(μ-H)(CO)10(μ-σ,η2-C≡CCMe2OMe) cluster

Triosmium cluster Os₃(-H)(CO)₁₀(--²-CCC Me₂OMe) (1) was obtained by treating OS₃(-H)(-Cl)(CO)₁₀ with LiCCCMe₂OMe. The reaction of cluster1 with HBF₄ · Et₂O at –60 °C leads to the cationic complex [Os₃(-H)(CO)₁₀(-,,²-C=C=C Me₂)]⁺BF₄ ^– (2) with an allenylidene ligand. The^s1H and¹³C NMR spectra of complex2 reveal the temperature dependence caused by migration of hydrocarbon and carbonyl ligands. Thermodynamic parameters were obtained for be exchange process of the allenylidene ligand.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 12, pp, 2990–2992, December, 1996.     

Spectrofluorimetric flow-injection determination of cerium in carbon and low alloy steels

Cerium can be determined spectrofluorimetrically (_em 350 nm, _ex 260 nm) based on the relatively intense native fluorescence of the cerium(III) aquo-ion. The main potential interference in the analysis of steel from iron(III), cerium(IV) and chromium(VI) are removed by use of a carrier solution containing 2.5% w/v hydroxylammonium chloride. The slight residual interference from iron(II) can be corrected by a matrix matching factor linearly related to the amount of iron present. The calibration graphs are linear over the range 0–7 g ml^–1 based on 250 l injection volumes. The sampling rate was 30 h^–1. The relative standard deviation was 2.0% (n=5) at 3 g ml^–1 cerium. The system has been applied to the determination of cerium in carbon or low alloy steels.     

Extractive spectrophotometric determination of dioxouranium(VI) with the sodium salt of hexamethyleneiminecarbodithioate

The optimum conditions for the extractive spectrophotometric determination of dioxouranium(VI) with hexamethyleneiminecarbodithioate(HMICdt) have been established. Dioxouranium(VI) reacts with this ligand at pH 4.5 to form a yellowish-orange uncharged 12 metal-ligand complex which can be extracted by chloroform. The calibration graph was linear in the range of 1–20 g ml^–1 of dioxouranium(VI) at 335 nm. The molar absorptivity of the extracted species is 5.952×10³ l mol^–1 cm^–1 with Sandell's sensitivity of 0.04 g cm^–2. The average of 10 determinations of dioxouranium was 49.75 g for the samples containing 50 g of U(VI) and the variation from the mean at 95% confidence limit was 49.75±0.5955.     

Development and Validation of an HPTLC–Densitometric Method for Determination of ACE Inhibitors

A high-performance thin layer chromatographic method coupled with densitometric analysis has been developed for measurement of benazepril and cilazapril, both pure and in their commercial dosage forms. The active substances were extracted from tablets with methanol (mean recovery 102%) and chromatographed on silica gel 60 F₂₅₄ HPTLC plates in horizontal chambers with ethyl acetate–acetone–acetic acid–water, 8:2:0.5:0.5 (v/v), as mobile phase. Chromatographic separation of these ACE inhibitors was followed by UV densitometric quantitation at 215 nm. Calibration plots were constructed in the range 0.4 to 2.0 g L^–1 for benazepril (2.0–10.0 g spot^–1) and from 0.5 to 1.5 g L^–1 for cilazapril (4.0–12.0 g spot^–1) with good correlation coefficients (r 0.990). The method was used to determine benazepril and cilazapril in pharmaceutical preparations with satisfactory precision (1.4% < RSD < 5.6%) and accuracy (1.7 < RE < 5.1).     

Spectrofluorimetric determination of nucleic acids as 8-hydroxyquinoline/ yttrium ternary complexes

The formation of nucleic acids/8-hydroxyquinoline/yttrium(III) ternary complexes and their fluorescent properties have been studied. The nucleic acids studied include native and thermally denatured calf thymus DNA, fish sperm DNA and yeast RNA. In the range of pH 7.6–8.5, controlled by NH₃-NH₄C1 buffer, ternary complexes are formed that fluoresce at different wavelengths with different nucleic acids. Based on the fluorescence reactions, sensitive spectrofluorimetric methods for nucleic acids are proposed. In optimal conditions, the calibration curves were linear in the range 0.5–4.0 gml^–1 for calf thymus DNA, 0.5–2.5 g ml^–1 for fish sperm DNA and 0.5–4.0 g ml^–1 for yeast RNA. The limits of determination (3 ) were 0.030 g ml^–1 for calf thymus DNA, 0.020 g ml^–1 for fish sperm DNA and 0.090 g ml^–1 for yeast RNA. Corresponding to the interferences of coexisting substances, six synthetic samples were constructed and the results of determination were satisfactory.