Degradation of Acid Orange 7 in aqueous solution by zero-valent aluminum under ultrasonic irradiation

Degradation of azo dye Acid Orange 7 (AO7) by zero-valent aluminum (ZVAl) in combination with ultrasonic irradiation was investigated. The preliminary studies of optimal degradation methodology were conducted with sole ultrasonic, sole ZVAl/air system, ultrasonication + ZVAl/air system (US-ZVAl). In ZVAl/air system, the degradation of AO7 could almost not be observed within 30 min. The degradation of AO7 by ZVAl/air system was obviously enhanced under ultrasound irradiation, and the enhancement is mainly attributed to that the production of hydroxyl radicals in ultrasound-ZVAl process was much higher than that in sole ultrasonic or in sole ZVAl/air system. The variables considered for the effect of degradation were the power of ultrasound, the initial concentration of AO7, as well as the initial pH value and the dosage of zero-valent aluminum. The results showed that the decolorization rate increased with the increase of power density and the dosage of ZVAl, but decreased with the increase of initial pH value and initial concentration of AO7. More than 96% of AO7 removal was achieved within 30 min under optimum operational conditions (AO7: 20 mg/L, ZVAl: 2 g/L, pH: 2.5, ultrasound: 20 kHz, 300 W). This study demonstrates that ultrasound-ZVAl process can effectively decolorize the azo dye AO7 in wastewater.     

Synergistic effects of combining ultrasound with the Fenton process in the degradation of Reactive Blue 19

The decoloration of reactive dye C.I. Reactive Blue 19 (RB 19) using combined ultrasound with the Fenton process has been investigated. The effect of varying the concentrations of hydrogen peroxide and iron sulfate, initial pH, ultrasonic power, initial dye concentration and dissolved gas on the decoloration and degradation efficiencies was measured. Calibration of the ultrasound systems was performed using calorimetric measurements and oxidative species monitoring using the Fricke dosimeter and degradations were carried out with a 20 kHz probe type transducer at 2, 4, 6 and 8 W cm⁻² of acoustic intensity at 15, 25, 50 and 75 mg L⁻¹ initial dye concentrations. First order rate kinetics was observed. It was found that while the degradation rate due to ultrasound alone was slow, sonication significantly accelerated the Fenton reaction. While the results were similar to those reported for other dyes, the effects occurred at lower concentrations. The rate and extent of decoloration of RB 19 increased with rising hydrogen peroxide concentration, ultrasonic powers and iron sulfate concentration but decreased with increasing dye concentration. An optimum pH value of pH = 3.5 was found. The rate of decoloration was higher when dissolved oxygen was present as compared with nitrogen and argon confirming the solution phase mechanism of the degradation.     

Sonocatalytic rapid degradation of Congo red dye from aqueous solution using magnetic Fe0/polyaniline nanofibers

Nano-sized magnetic Fe⁰/polyaniline (Fe⁰/PANI) nanofibers were used as an effective material for sonocatalytic degradation of organic anionic Congo red (CR) dye. Fe⁰/PANI_, was synthesized via reductive deposition of nano-Fe⁰ onto the PANI nanofibers at room temperature. Prepared catalyst was characterized using HR-TEM, FE-SEM, XRD, FTIR instruments. The efficacy of catalyst in removing CR was assessed colorimetrically using UV–visible spectroscopy under different experimental conditions such as % of Fe⁰ loading into the composite material, solution pH, initial concentration of dye, catalyst dosage, temperature and ultrasonic power. The optimum conditions for sonocatalytic degradation of CR were obtained at catalyst concentrations = 500 mg.L⁻¹, concentration of CR = 200 ppm, solution pH = neutral (7.0), temperature = 30 °C, % of Fe⁰ loading = 30% and 500 W ultrasonic power. The experimental results showed that ultrasonic process could remove 98% of Congo red within 30 min with higher Q_max value (Q_max = 446.4 at 25 °C). The rate of degradation of CR dye was much faster in this ultrasonic technique rather than conventional adsorption process. The degradation efficiency declined with the addition of common inorganic salts (NaCl, Na₂CO₃, Na₂SO₄ and Na₃PO₄). The rate of degradation suppressed more with increasing salt concentration. Kinetic and isotherm studies indicated that the degradation of CR provides pseudo-second order rate kinetic and Langmuir isotherm model compared to all other models tested. The excellent high degradation capacity of Fe⁰/PANI under ultrasonic irradiation can be explained on the basis of the formation of active hydroxyl radicals (OH) and subsequently a series of free radical reactions.     

Degradation of Acid Blue 25 in aqueous media using 1700 kHz ultrasonic irradiation: ultrasound/Fe(II) and ultrasound/H2O2 combinations

In this work, the sonolytic degradation of an anthraquinonic dye, C.I. Acid Blue 25 (AB25), in aqueous phase using high frequency ultrasound waves (1700 kHz) for an acoustic power of 14 W was investigated. The sonochemical efficiency of the reactor was evaluated by potassium iodide dosimeter, Fricke reaction and hydrogen peroxide production yield. The three investigated methods clearly show the production of oxidizing species during sonication and well reflect the sonochemical effects of high frequency ultrasonic irradiation. The effect of operational conditions such as the initial AB25 concentration, solution temperature and pH on the degradation of AB25 was studied. Additionally, the influence of addition of salts on the degradation of dye was examined. The rate of AB25 degradation was dependent on initial dye concentration, pH and temperature. Addition of salts increased the degradation of dye. Experiments conducted using distilled and natural waters demonstrated that the degradation was more efficient in the natural water compared to distilled water. To increase the efficiency of AB25 degradation, experiments combining ultrasound with Fe(II) or H₂O₂ were conducted. Fe(II) induced the dissociation of ultrasonically produced hydrogen peroxide, leading to additional OH radicals which enhance the degradation of dye. The combination of ultrasound with hydrogen peroxide looks to be a promising option to increase the generation of free radicals. The concentration of hydrogen peroxide plays a crucial role in deciding the extent of enhancement obtained for the combined process. The results of the present work indicate that ultrasound/H₂O₂ and ultrasound/Fe(II) processes are efficient for the degradation of AB25 in aqueous solutions by high frequency ultrasonic irradiation.     

Degradation of 4-chloro 2-aminophenol using combined strategies based on ultrasound,photolysis and ozone

The present work investigates the degradation of 4-chloro 2-aminophenol (4C2AP), a highly toxic organic compound, using ultrasonic reactors and combination of ultrasound with photolysis and ozonation for the first time. Two types of ultrasonic reactors viz. ultrasonic horn and ultrasonic bath operating at frequency of 20 kHz and 36 kHz respectively have been used in the work. The effect of initial pH, temperature and power dissipation of the ultrasonic horn on the degradation rate has been investigated. The established optimum parameters of initial pH as 6 (natural pH of the aqueous solution) and temperature as 30 ± 2 °C were then used in the degradation studies using the combined approaches. Kinetic study revealed that degradation of 4C2AP followed first order kinetics for all the treatment approaches investigated in the present work. It has been established that US + UV + O₃ combined process was the most promising method giving maximum degradation of 4C2AP in both ultrasonic horn (complete removal) and bath (89.9%) with synergistic index as 1.98 and 1.29 respectively. The cavitational yield of ultrasonic bath was found to be eighteen times higher as compared to ultrasonic horn implying that configurations with higher overall areas of transducers would be better selection for large scale treatment. Overall, the work has clearly demonstrated that combined approaches could synergistically remove the toxic pollutant (4C2AP).     

Medium-high frequency ultrasound and ozone based advanced oxidation for amoxicillin removal in water

In this study, treatment of an antibiotic compound amoxicillin by medium-high frequency ultrasonic irradiation and/or ozonation has been studied. Ultrasonic irradiation process was carried out in a batch reactor for aqueous amoxicillin solutions at three different frequencies (575, 861 and 1141 kHz). The applied ultrasonic power was 75 W and the diffused power was calculated as 14.6 W/L. The highest removal was achieved at 575 kHz ultrasonic frequency (>99%) with the highest pseudo first order reaction rate constant 0.04 min⁻¹ at pH 10 but the mineralization achieved was around 10%. Presence of alkalinity and humic acid species had negative effect on the removal efficiency (50% decrease). To improve the poor outcomes, ozonation had been applied with or without ultrasound. Ozone removed the amoxicillin at a rate 50 times faster than ultrasound. Moreover, due to the synergistic effect, coupling of ozone and ultrasound gave rise to rate constant of 2.5 min⁻¹ (625 times higher than ultrasound). In the processes where ozone was used, humic acid did not show any significant effect because the rate constant was so high that ozone has easily overcome the scavenging effects of natural water constituents. Furthermore, the intermediate compounds, after the incomplete oxidation mechanisms, has been analyzed to reveal the possible degradation pathways of amoxicillin through ultrasonic irradiation and ozonation applications. The outcomes of the intermediate compounds experiments and the toxicity was investigated to give a clear explanation about the safety of the resulting solution. The relevance of all the results concluded that hybrid advanced oxidation system was the best option for amoxicillin removal.     

Ultrasonic preparation of cationic cotton and its application in ultrasonic natural dyeing

Cationization of cotton fabric was conferred by the sonicator reaction of cellulose with bromoacetyl bromide, followed by substitution of the terminal bromo groups by triethylamine. Experiments showed that the optimal volume of bromoacetyl bromide necessary to succeed the first stage was 0.4 mL. The order of weight gain for various processes indicates, ultrasound, 25 kHz > ultrasound, 40 kHz > mechanical stirring. Also, for the second stage the order of nitrogen contents indicates ultrasound, 25 kHz > ultrasound, 40 kHz > mechanical stirring. The structures of both untreated and cationic fibres were investigated by FTIR spectroscopy. Modified cotton fabric was subsequently dyed in both conventional and ultrasonic techniques with isosalipurposide dye isolated from Acacia cyanophylla yellow flowers. The effect of dye bath pH, ultrasonic power and frequency, dyeing time and temperature were studied and the order of K/S values indicates ultrasound, 25 kHz > ultrasound, 40 kHz > CH. ultrasound was also found to enhance the dye uptake and the overall fastness properties. Analysis of the sorption isotherms of isosalipurposide dye on cationic cotton fabric shows that the Languimir isotherm equation is best able to correlate the data.     

Alternate pulses of ultrasound and electricity enhanced electrochemical process for p-nitrophenol degradation

A novel alternated ultrasonic and electric pulse enhanced electrochemical process was developed and used for investigating its effectiveness on the degradation of p-nitrophenol (PNP) in an aqueous solution. The impacts of pulse mode, pH, cell voltage, supporting electrolyte concentration, ultrasonic power and the initial concentration of PNP on the performance of PNP degradation were evaluated. Possible pathway of PNP degradation in this system was proposed based on the intermediates identified by GC–MS. Experimental results showed that 94.1% of PNP could be removed at 2 h in the dual-pulse ultrasound enhanced electrochemical (dual-pulse US-EC) process at mild operating conditions (i.e., pulse mode of electrochemical pulse time (T_EC) = 50 ms and ultrasonic pulse time (T_US) = 100 ms, initial pH of 3.0, cell voltage of 10 V, Na₂SO₄ concentration of 0.05 M, ultrasonic powder of 48.8 W and initial concentration of PNP of 100 mg/L), compared with 89.0%, 58.9%, 2.4% in simultaneous ultrasound enhanced electrochemical (US-EC) process, pulsed electrochemical (EC) process and pulsed ultrasound (US), respectively. Moreover, energy used in the dual-pulse US-EC process was reduced by 50.4% as compared to the US-EC process. The degradation of PNP in the pulsed EC process, US-EC process and dual-pulse process followed pseudo-first-order kinetics. Therefore, the dual-pulse US-EC process was found to be a more effective technique for the degradation of PNP and would have a promising application in wastewater treatment.     

Decolorization of azo dye Orange G by aluminum powder enhanced by ultrasonic irradiation

In this work, the decolorization of azo dye Orange G (OG) in aqueous solution by aluminum powder enhanced by ultrasonic irradiation (AlP-UI) was investigated. The effects of various operating operational parameters such as the initial pH, initial OG concentration, AlP dosage, ultrasound power and added hydrogen peroxide (H₂O₂) concentration were studied. The results showed that the decolorization rate was enhanced when the aqueous OG was irradiated simultaneously by ultrasound in the AlP-acid systems. The decolorization rate decreased with the increase of both initial pH values of 2.0–4.0 and OG initial concentrations of 10–80 mg/L, increased with the ultrasound power enhancing from 500 to 900 W. An optimum value was reached at 2.0 g/L of the AlP dosage in the range of 0.5–2.5 g/L. The decolorization rate enhanced significantly by the addition of hydrogen peroxide in the range of 10–100 mM to AlP-UI system reached an optimum value of 0.1491 min⁻¹. The decolorization of OG appears to involve primarily oxidative steps, the cleavage of NN bond, which were verificated by the intermediate products of OG under the optimal tested degradation system, aniline and 1-amino-2-naphthol-6,8-disulfonate detected by the LC–MS.     

Degradation of C.I. Direct Black 168 from aqueous solution by fly ash/H2O2 combining ultrasound

Degradation of C.I. Direct Black 168 from aqueous solution using Fenton-like reactions combining ultrasound was investigated. In the presence of H₂O₂, the effect of the heterogeneous catalysts, such as fly ash, kaolinite or diatomaceous earth on the degradation of Direct Black 168 was observed under ultrasound. The fly ash was the most efficient catalyst. It is apparent that ultrasound can prompt the reaction to take place and give in higher degradation. In the combination of ultrasound and fly ash/H₂O₂, the effect of different system variables namely concentration of the dye, dosage of fly ash, concentration of H₂O₂, pH of solution and the addition of NaCl were studied. 99.0% removal ratio was achieved at initial concentration 100 mg/L, pH 3.0, and dosage of fly ash 2.0 g/L, as well as 2.94 mM H₂O₂. NaCl exhibited only a minor effect on the dye removal.     

Mechanism and dynamic study of reactive red X-3B dye degradation by ultrasonic-assisted ozone oxidation process

The effectiveness of ozone combined with ultrasound techniques in degrading reactive red X-3B is evaluated. A comparison among ozone (O₃), ultrasonic (US), ozone/ultrasonic (O₃/US) for degradation of reactive red X-3B has been performed. Results show that O₃/US system was the most effective and the optimally synergetic factor reaches to 1.42 in O₃/US system. The cavitation of ultrasound plays an important role during the degradation process. It is found that 99.2% of dye is degraded within 6 min of reaction at the initial concentration of 100 mg·L⁻¹, pH of 6.52, ozone flux of 40 L·h⁻¹ and ultrasonic intensity of 200 W·L⁻¹. Ozonation reactions in conjunction with sonolysis indicate that the decomposition followed pseudo-first-order reaction kinetics but the degradation efficiencies are affected by operating conditions, particularly initial pH and ultrasonic intensity. A kinetic model is established based on the reaction corresponding to operational parameters. In addition, the main reaction intermediates, such as p-benzoquinone, catechol, hydroquinone, phthalic anhydride and phthalic acid, are separated and identified using GC/MS and a possible degradation pathway is proposed during the O₃/US process.     

Intensified removal of copper from waste water using activated watermelon based biosorbent in the presence of ultrasound

Copper is one of the most toxic heavy metals having significant effects on the living organisms and hence effective removal of copper from waste water is crucial. The current work investigates the application of activated watermelon shell based biosorbent for the removal of copper from aqueous solution. The effect of activation using calcium hydroxide and citric acid as well as the effect of operating parameters like contact time, adsorbent dosage, temperature, pH, initial concentration and ultrasonic power on the extent of removal has been investigated. Experiments performed in the presence of ultrasound to investigate the degree of intensification as compared to the conventional agitation based treatment revealed that the adsorption rate significantly increases in the presence of ultrasound and also the time required for reaching the equilibrium reduces from 60 min in conventional approach to only 20 min in the presence of ultrasound. The extent of adsorption of Cu(II) on adsorbents was found to increase with an increase in the operating pH till an optimum value of 5. The extent of adsorption also increased with a decrease in the initial concentration and particle size as well as with an increase in ultrasonic power till an optimum. Kinetics and isotherm study revealed that all the experimental data was found to best fit the pseudo second order kinetics and Langmuir adsorption isotherm model respectively. Maximum adsorption capacity was found to be 31.25 mg/g for watermelon treated with calcium hydroxide and 27.027 mg/g for watermelon treated with citric acid. Overall present study established that activated watermelon is an environmentally friendly, low cost and highly efficient biosorbent that can be successfully applied for the removal of copper from aqueous solution with intensification benefits based on the ultrasound assisted approach.     

Intensification of sonochemical degradation of ammonium perfluorooctanoate by persulfate oxidant

Ammonium perfluorooctanoate (APFO) is an emerging environmental pollutant attracting significant attention due to its global distribution, high persistence, and bioaccumulation properties. The decomposition of APFO in aqueous solution with a combination of persulfate oxidant and ultrasonic irradiation was investigated. The effects of operating parameters, such as ultrasonic power, persulfate concentration, APFO concentration, and initial media pH on APFO degradation were discussed. In the absence of persulfate, 35.5% of initial APFO in 46.4 μmol/L solution under ultrasound irradiation, was decomposed rapidly after 120 min with the defluorination ratio reaching 6.73%. In contrast, when 10 mmol/L persulfate was used, 51.2% of initial APFO (46.4 μmol/L) was decomposed and the defluorination ratio reached 11.15% within 120 min reaction time. Enhancement of the decomposition of APFO can be explained by acceleration of substrate decarboxylation, induced by sulfate radical anions formed from the persulfate during ultrasonic irradiation. The SO₄^−•/APFO reactions at the bubble-water interface appear to be the primary pathway for the sonochemical degradation of the perfluorinated surfactants.     

Degradation of nitrobenzene in aqueous solution by dual-pulse ultrasound enhanced electrochemical process

The present work reports a novel dual-pulse ultrasound enhanced electrochemical degradation (US-ECD) process that synchronizes alternatively ultrasound pulses and potential pulses to degrade nitrobenzene in aqueous solution with a high percentage degradation and low energy consumption. In comparison to the test results generated from the conventional US-ECD and original electrochemical degradation (ECD) process, the dual-pulse US-ECD process increased degradation percentages to nitrobenzene by 2% and 17%, respectively, while energy used in the pulse process was only about 46.5% of that was used in the conventional US-ECD process. Test results demonstrated a superior performance of the dual-pulse US-ECD process over those of other conventional ones. Impacts of pulse mode, initial pH value, cell voltage, supporting electrolyte concentration and ultrasonic power on the process performances were investigated. With operation conditions optimized in the study at pH = 3.0, cell voltage = 10 V, ultrasonic power = 48.84 W, electrolyte concentration = 0.1 M and an experiment running time of 30 min, the percentage degradation of nitrobenzene could reach 80% (US pulse time = 50 ms and ECD pulse time = 50 ms). This process provided a reliable and effective technical approach to degrade nitrobenzene in aqueous solution and significantly reduced energy consumption in comparison to the conventional US-ECD or original ECD treatment.     

Removal of Brilliant Green from wastewater using conventional and ultrasonically prepared poly(acrylic acid) hydrogel loaded with kaolin clay: A comparative study

The present work deals with the removal of Brilliant Green dye from wastewater using a poly(acrylic acid) hydrogel composite (PAA-K hydrogel) prepared by incorporation of kaoline clay. The composite has been synthesized using ultrasound assisted polymerization process as well as the conventional process, with an objective of showing the better effectiveness of ultrasound assisted synthesis. It has been observed that the hydrogel prepared by ultrasound assisted polymerization process showed better results. The optimum conditions for the removal of dye are pH of 7, temperature of 35 °C, initial dye concentration of 30 mg/L and hydrogel loading of 1 g. The extent of removal of dye increased with an increase in the contact time and initial dye concentration. A pseudo-second-order kinetic model has been developed to explain the adsorption kinetics of dye on the PAA-K hydrogel. Thermodynamic and kinetic parameters indicate that the adsorption process is spontaneous in nature and the PAA-K hydrogel prepared by ultrasound process is a promising adsorbent compared to conventional process. The obtained adsorption data has also been fitted into commonly used adsorption isotherms and it has been found that Freundlich as well as Langmuir adsorption isotherm models fits well to the experimental results.     

Sonocatalytic removal of ibuprofen and sulfamethoxazole in the presence of different fly ash sources

We examined the feasibility of using two types of fly ash (an industrial waste from thermal power plants) as a low-cost catalyst to enhance the ultrasonic (US) degradation of ibuprofen (IBP) and sulfamethoxazole (SMX). Two fly ashes, Belews Creek fly ash (BFA), from a power station in North Carolina, and Wateree Station fly ash (WFA), from a power station in South Carolina, were used. The results showed that >99% removal of IBP and SMX was achieved within 30 and 60 min of sonication, respectively, at 580 kHz and pH 3.5. Furthermore, the removal of IBP and SMX achieved, in terms of frequency, was in the order 580 kHz > 1000 kHz > 28 kHz, and in terms of pH, was in the order of pH 3.5 > pH 7 > pH 9.5. WFA showed significant enhancement in the removal of IBP and SMX, which reached >99% removal within 20 and 50 min, respectively, at 580 kHz and pH 3.5. This was presumably because WFA contains more silicon dioxide than BFA, which can enhance the formation of OH radicals during sonication. Additionally, WFA has finer particles than BFA, which can increase the adsorption capacity in removing IBP and SMX. The sonocatalytic degradation of IBP and SMX fitted pseudo first-order rate kinetics and the synergistic indices of all the reactions were determined to compare the efficiency of the fly ashes. Overall, the findings have showed that WFA combined with US has potential for treating organic pollutants, such as IBP and SMX, in water and wastewater.     

Sonolysis of levodopa and paracetamol in aqueous solutions

Pharmaceutical products are often present in wastewater treatment effluents, rivers, lakes and, more rarely, in groundwater. The advanced oxidation methods, like ultrasound, find a promising future in the area of wastewater treatment. The aim of this paper is to evaluate the influence of several parameters of the ultrasound process on the degradation of paracetamol, a widely used non-steroidal anti-inflammatory recalcitrant drug found in water and levodopa, the most frequently prescribed drug for the treatment of Parkinson disease. Experiments were carried out at 574, 860 and 1134 kHz of ultrasonic frequency with horn-type sonicator and actual power values of 9, 17, 22 and 32 W at 20 °C. Initial concentrations of 25, 50, 100 and 150 mg L^?1 of both products were used. Treatment efficiency was assessed following changes in pharmaceuticals concentration and chemical oxygen demand.The sonochemical degradation of both products follows a pseudo-first-order reaction kinetics. Complete removal of pharmaceuticals was achieved in some cases but some dissolved organic carbon remains in solution showing that long lived intermediates were recalcitrant to ultrasound irradiation. Pollutants conversion and COD removal were found to decrease with increasing the initial solute concentration and decreasing power. The best results were obtained with 574 kHz frequency. Investigations using 1-butanol as radical scavenger and H₂O₂ as promoter revealed that pollutants degradation proceeds principally through radical reactions, although some differences were observed between both molecules. Addition of H₂O₂ had a positive effect on degradation rate, but the optimum concentration of hydrogen peroxide depends on the pollutant.     

Effects and mechanism of diclofenac degradation in aqueous solution by US/Zn0

A system of ultrasound radiation coupled with Zn⁰ was applied to degrade diclofenac. The effects of initial pH, dosage of Zn⁰ and ultrasound density were investigated. To further explore the mechanism of the microcosmic reaction, the fresh and used Zn⁰ powders were characterized by SEM, XRD and XPS. Radical scavengers were used to determine the oxidation performance of strong oxidizing free radicals on diclofenac, including hydroxyl radicals and superoxide radicals. The results showed that the optimum removal of diclofenac reached to over 85% at pH of 2.0 in 15 min, with Zn⁰ dosage of 0.1 g/L and ultrasound density of 0.6 W/cm³. TOC removal of 72.6% in 15 min and dechlorination efficiency of diclofenac reached 70% in 30 min. Characterization results showed that a ZnO membrane was generated on the surface of Zn particles after use. According to the mass spectrometry results, several possible pathways of diclofenac degradation were proposed, and most diclofenac was turned into micro-molecules or CO₂ finally. The synergistic effect of US/Zn⁰ in the reactions led to a proposed degradation mechanism in which zinc could directly attack the target contaminant diclofenac because of its good reducibility with the auxiliary functions of ultrasonic irradiation, mechanical shearing and free radical oxidation.     

Novel approaches based on ultrasound for treatment of wastewater containing potassium ferrocyanide

Industrial wastewaters containing biorefractory compounds like cyanide offer significant environmental problems attributed to the fact that the conventional methods have limited effectiveness and hence developing efficient treatment approaches is an important requirement. The present work investigates the use of novel treatment approach of ultrasound (US) combined with advanced oxidation techniques for the degradation of potassium ferrocyanide (KFC) for the first time. An ultrasonic bath equipped with longitudinal horn (1 kW rated power and 25 kHz frequency) has been used. The effect of initial pH (2–9) on the progress of degradation has been investigated initially and subsequently using the optimized pH, effect of addition of hydrogen peroxide (ratio of KFC:H₂O₂ varied over the range of 1:0.5–1:5) and TiO₂ in the presence of H₂O₂ (1:1 ratio by weight of TiO₂) as process intensifying approach has been studied. Combination of ultrasonic irradiation with ozone (O₃) (100–400 mg/h) and ultraviolet irradiation (UV) has also been investigated. Use of combination of US with H₂O_2, H₂O₂ + TiO₂ and ozone resulted in extent of KFC degradation as 54.2%, 74.82% and 82.41% respectively. Combination of US with both UV and ozone was established to be the best approach yielding 92.47% degradation. The study also focused on establishing kinetic rate constants for all the treatment approaches which revealed that all the approaches followed first order kinetic mechanism with higher rate constants for the combination approaches. Overall, it has been conclusively established that ultrasound based combined treatment schemes are very effective for the treatment of KFC containing wastewaters.