Bioremediation of Perfluoroalkyl Substances (PFAS) by Anaerobic Digestion: Effect of PFAS on Different Trophic Groups and Methane Production Accelerated by Carbon Materials

Per- and polyfluoroalkyl substances (PFAS) are recalcitrant pollutants which tend to persist in soils and aquatic environments and their remediation is among the most challenging with respect to organic pollutants. Anaerobic digestion (AD) supplemented with low amounts of carbon materials (CM), acting as electron drivers, has proved to be an efficient process for the removal of organic compounds from wastewater. This work explores the impact of PFAS on different trophic groups in anaerobic communities, and the effect of carbon nanotubes (CNT), activated carbon (AC), and oxidized AC (AC-HNO₃), as electron shuttles on the anaerobic bioremoval of these compounds, based on CH₄ production. The inhibition of the specific methanogenic activity (SMA) exerted by perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS), at a concentration of 0.1 mg L⁻¹, was below 10% for acetoclastic and below 15%, for acetogenic communities. Hydrogenotrophic methanogens were not affected by the presence of PFAS. All CM reduced the negative impact of PFAS on the CH₄ production rate, but AC was the best. Moreover, the methanization percentage (MP) of sewage sludge (SS) increased 41% in the presence of PFOS (1.2 g L⁻¹) and AC. In addition, AC fostered an increase of 11% in the MP of SS+PFOS, relative to the condition without AC. AC promoted detoxification of PFOA- and PFOS-treated samples by 51% and 35%, respectively, as assessed by Vibrio fischeri assays, demonstrating the advantage of bringing AD and CM together for PFAS remediation.     

Remarkably efficient removal of toxic bromate from drinking water with a porphyrin–viologen covalent organic framework

The presence of carcinogenic bromate (BrO₃⁻) in drinking water became a global concern and efforts towards its removal mainly focused on addressing the source. Herein, we rationally designed a porphyrin-based covalent organic framework (PV-COF) with a cationic surface to provide electrostatic interactions and a porphyrin core to induce hydrogen bonding interactions for the efficient removal of BrO₃⁻ from water. Through H-bonding and electrostatic interactions, PV-COF exhibited an exceptional bromate removal efficiency (maximum adsorption capacity, Q_max: 203.8 mg g⁻¹) with the fastest uptake rate (k_ads) of 191.45 g mg⁻¹ min⁻¹. The bromate concentration was reduced to far below the allowed concentration in drinking water (10 ppb) within 20 minutes. We studied the relationship between bromate adsorption and COF surface modification by metalation of the porphyrinic core or neutralization of the viologen linkers by chemical reduction. The bromate adsorption mechanism was studied by EDAX mapping and molecular simulations, and it was found that ion exchange and hydrogen bonding formation drive the adsorption. Importantly, PV-COF could be easily recycled several times without compromising its adsorption efficiency.

A cationic COF removes carcinogenic bromate with a remarkable rate constant of 191.45 g mg⁻¹ min⁻¹.     

Detection of Per- and Polyfluoroalkyl Substances (PFAS) by Interrupted Energy Transfer

The ubiquitous presence of per- and polyfluoroalkyl substances (PFAS) in aqueous environments has aroused societal concern. Nonetheless, effective sensing technologies for continuous monitoring of PFAS within water distribution infrastructures currently do not exist. Herein, we describe a ratiometric sensing approach to selectively detect aqueous perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) at concentrations of μg ⋅ L⁻¹. Our method relies on the excitonic transport in a highly fluorinated poly(p-phenylene ethynylene) to amplify a ratiometric emission signal modulated by an embedded fluorinated squaraine dye. The electronic coupling between the polymer and dye occurs through overlap of π-orbitals and is designed such that energy transfer is dominated by an electron-exchange (Dexter) mechanism. Exposure to aqueous solutions of PFAS perturbs the orbital interactions between the squaraine dye and the polymer backbone, thereby diminishing the efficiency of the energy transfer and producing a “polymer-ON/dye-OFF” response. These polymer/dye combinations were evaluated in spin-coated films and polymer nanoparticles and were able to selectively detect PFAS at concentrations of ca. 150 ppb and ca. 50 ppb, respectively. Both polymer films and nanoparticles are not affected by the type of water, and similar responses to PFAS were found in milliQ and well water.     

A switchable sensor and scavenger: detection and removal of fluorinated chemical species by a luminescent metal–organic framework

Fluorosis has been regarded as a worldwide disease that seriously diminishes the quality of life through skeletal embrittlement and hepatic damage. Effective detection and removal of fluorinated chemical species such as fluoride ions (F⁻) and perfluorooctanoic acid (PFOA) from drinking water are of great importance for the sake of human health. Aiming to develop water-stable, highly selective and sensitive fluorine sensors, we have designed a new luminescent MOF In(tcpp) using a chromophore ligand 2,3,5,6-tetrakis(4-carboxyphenyl)pyrazine (H₄tcpp). In(tcpp) exhibits high sensitivity and selectivity for turn-on detection of F⁻ and turn-off detection of PFOA with a detection limit of 1.3 μg L⁻¹ and 19 μg L⁻¹, respectively. In(tcpp) also shows high recyclability and can be reused multiple times for F⁻ detection. The mechanisms of interaction between In(tcpp) and the analytes are investigated by several experiments and DFT calculations. These studies reveal insightful information concerning the nature of F⁻ and PFOA binding within the MOF structure. In addition, In(tcpp) also acts as an efficient adsorbent for the removal of F⁻ (36.7 mg g⁻¹) and PFOA (980.0 mg g⁻¹). It is the first material that is not only capable of switchable sensing of F⁻ and PFOA but also competent for removing the pollutants via different functional groups.

A robust In-MOF, In(tcpp), demonstrates sensitive detection of the fluorinated chemical species F⁻ and PFOA via distinctly different luminescence signal change, and effective adsorption and removal of both species from aqueous solution.     

Determination of perfluorooctanoic acid and perfluorooctane sulfonate by automated in-tube solid-phase microextraction coupled with liquid chromatography-mass spectrometry

We have developed a simple, rapid, and sensitive method for the determination of perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) by on-line in-tube solid-phase microextraction (SPME) coupled with liquid chromatography-mass spectrometry (LC-MS). PFOA and PFOS were separated within 10 min by high-performance liquid chromatography using an Inertsil ODS-3 column and 10 mM ammonium acetate/methanol (35/65, v/v) as a mobile phase at a flow rate of 0.25 mL min⁻¹. Electrospray ionization conditions in the negative ion mode were optimized for MS detection of PFOA and PFOS. The optimum in-tube SPME conditions were 20 draw/eject cycles with a sample size of 40 μL using a CP-Pora PLOT amine capillary column as the extraction device. The extracted compounds could be desorbed easily from the capillary by passage of the mobile phase, and no carryover was observed. Using the in-tube SPME LC-MS method, good linearity of the calibration curve (r = 0.9990 for PFOA, r = 0.9982 for PFOS) was obtained in the range of 0.05-5 ng mL⁻¹ each compound. The detection limits (S/N = 3) for PFOA and PFOS were 1.5 and 3.2 pg mL⁻¹, respectively. The method described here showed about 100-fold higher sensitivity than the direct injection method. The within-day and between-day precisions (relative standard deviations) were below 3.7 and 6.0%, respectively. This method was applied successfully to the analysis of PFOA and PFOS in environmental water samples and to the elution test from a Teflon^®-coated frying pan without interference peaks. The recoveries of PFOA and PFOS spiked into river samples were above 81%, and PFOA was detected at pg mL⁻¹ levels in environmental water samples and eluate from the frying pan.     

Confirmatory Analysis of Per and Polyfluoroalkyl Substances in Milk and Infant Formula Using UHPLC–MS/MS

An ultra-high performance liquid chromatography tandem mass spectrometry method was developed and validated for the sensitive determination and unambiguous confirmation of residues of per and polyfluorinated alkyl substances (PFAS) in breastmilk, retail milk and infant formulas following two sample preparation methods. Sample pre-treatment was carried out by a simplified QuEChERS method without requiring dSPE or any further clean-up. The method was validated in accordance with the requirements of Commission Decision 657/2002/EC with slight modifications. The method displayed good linearity with R² ranging from 0.9843–0.9998 for all target PFAS. The recovery and within-laboratory reproducibility of the method (n = 63) were in the range 60–121% and 5–28%, respectively. The decision limit, detection capability and limit of quantitation ranged from 30–60 ng kg⁻¹ to 40–100 ng kg⁻¹ and 5–50 ng kg⁻¹, respectively. Acceptable matrix effect values in the range −45–29% were obtained with uncertainty of measurement lower than 25% for all target PFAS. The method displays its suitability for the sensitive and high-throughput confirmatory analysis of C₄–C₁₄ PFAS in breastmilk, dairy milk and infant formulas.     

Determination of perfluorooctanesulfonate and perfluorooctanoate in water samples by SPE-HPLC/electrospray ion trap mass spectrometry

Perfluorooctanesulfonate (PFOS) and perfluorooctanoate (PFOA) are the most notable members of an emerging class of persistent organic pollutants (POPs), perfluorochemicals (PFCs). A method for the determination of PFOS and PFOA in water samples was developed and validated in this study. Water samples collected from river and industrial effluent at Guangzhou, one of the most industrialized regions in China, were analyzed by solid-phase extraction (SPE) followed by high-performance liquid chromatography (HPLC) negative electrospray ionization (ESI) mass spectrometry. Operational parameters of the ion trap mass spectrometer were optimized to improve sensitivity and selectivity of this method. The limits of quantitation and recoveries were 2.0 ng L^− 1 and 75% for PFOA and 0.50 ng L^− 1 and 88% for PFOS, respectively. In river water samples, 2.3-33 ng L^− 1 of PFOS and < 2.0-11 ng L^− 1 of PFPA were detected. And sewage effluents contained considerably higher concentrations of PFOS and PFOA.     

One-Pot Facile Synthesis of Noble Metal Nanoparticles Supported on rGO with Enhanced Catalytic Performance for 4-Nitrophenol Reduction

In this study, reduced graphene oxide (rGO)-supported noble metal (gold, silver, and platinum) nanoparticle catalysts were prepared via the one-pot facile co-reduction technique. Various measurement techniques were used to investigate the structures and properties of the catalysts. The relative intensity ratios of I_D/I_G in rGO/Au, rGO/Ag, rGO/Pt, and GO were 1.106, 1.078, 1.047, and 0.863, respectively. The results showed the formation of rGO and that noble metal nanoparticles were decorated on rGO. Furthermore, the catalytic activities of the designed nanocomposites were investigated via 4-nitrophenol. The catalysts were used in 4-nitrophenol reduction. The catalytic performance of the catalysts was evaluated using the apparent rate constant k values. The k value of rGO/Au was 0.618 min⁻¹, which was higher than those of rGO/Ag (0.55 min⁻¹) and rGO/Pt (0.038 min⁻¹). The result proved that the rGO/Au catalyst exhibited a higher catalytic performance than the rGO/Ag catalyst and the rGO/Pt catalyst. The results provide a facile method for the synthesis of rGO-supported nanomaterials in catalysis.     

Calcium Sulfite Solids Activated by Iron for Enhancing As(III) Oxidation in Water

Desulfurized gypsum (DG) as a soil modifier imparts it with bulk solid sulfite. The Fe(III)–sulfite process in the liquid phase has shown great potential for the rapid removal of As(III), but the performance and mechanism of this process using DG as a sulfite source in aqueous solution remains unclear. In this work, employing solid CaSO₃ as a source of SO₃²⁻, we have studied the effects of different conditions (e.g., pH, Fe dosage, sulfite dosage) on As(III) oxidation in the Fe(III)–CaSO₃ system. The results show that 72.1% of As(III) was removed from solution by centrifugal treatment for 60 min at near-neutral pH. Quenching experiments have indicated that oxidation efficiencies of As(III) are due at 67.5% to HO^•, 17.5% to SO₅^•− and 15% to SO₄^•−. This finding may have promising implications in developing a new cost-effective technology for the treatment of arsenic-containing water using DG.     

Fabrication of Phosphorus-Doped Cobalt Silicate with Improved Electrochemical Properties

The development of electrode materials for supercapacitors (SCs) is greatly desired, and this still poses an immense challenge for researchers. Cobalt silicate (Co₂SiO₄, denoted as CoSi) with a high theoretical capacity is deemed to be one of the sustainable electrode materials for SCs. However, its achieved electrochemical properties are still not satisfying. Herein, the phosphorus (P)-doped cobalt silicate, denoted as PCoSi, is synthesized by a calcining strategy. The PCoSi exhibits 1D nanobelts with a specific surface area of 46 m²∙g⁻¹, and it can significantly improve the electrochemical properties of CoSi. As a supercapacitor’s (SC’s) electrode, the specific capacitance of PCoSi attains 434 F∙g⁻¹ at 0.5 A∙g⁻¹, which is much higher than the value of CoSi (244 F∙g⁻¹ at 0.5 A∙g⁻¹). The synergy between the composition and structure endows PCoSi with attractive electrochemical properties. This work provides a novel strategy to improve the electrochemical performances of transition metal silicates.     

Validation of a screening method based on liquid chromatography coupled to high-resolution mass spectrometry for analysis of perfluoroalkylated substances in biota

A screening method for analysis of perfluoroalkylated substances (PFAS) in biota samples has been developed and validated using liver samples from polar cod (Boreogadus saida) and glaucous gull (Larus hyperboreus). The method was based on extraction of target compounds from homogenised samples into the solvent mixture used as mobile phase in high-performance liquid chromatography (HPLC), i.e. methanol/water (50:50; 2 mM ammonium acetate). The extract was filtered and directly injected into a HPLC/time-of-flight mass spectrometry (TOF-MS) system. Quantification was performed using 7H-perfluoroheptanoic acid as internal standard and a calibration standard solution dissolved in sample extract for each matrix type (matrix-matched calibration standard). The method is very time and cost efficient. Except for long-chain compounds and perfluorooctane sulfonamide (which cannot be covered by this method), recoveries were between 60% and 115% and method detection limits were in the range 0.04-1.3 ng/g wet weight. Blank values could be neglected with the exception of perfluorooctane sulfonate (PFOS), perfluorohexanoic acid (PFHxA) and perfluorooctanoic acid (PFOA). One of the major challenges in PFAS analysis is ionisation disturbance by co-eluting matrix in the ion source of the mass spectrometer. Both matrix and analyte specific signal enhancement and suppression was observed and quantified. Repeated extractions (n = 3) gave relative standard deviations (RSD) <35% for all PFAS. Accuracy was examined by comparing the screening method to the generally applied ion pair extraction (IPE) method. PFAS concentration values of a glaucous gull liver sample deviated by less than 30% for the two methods, provided that matrix-matched calibration standards were employed in both methods.     

Method optimization for determination of selected perfluorinated alkylated substances in water samples

In recent years perfluorinated alkylated substances (PFAS) have appeared as a new class of global pollutant. Besides being an industrially important group of compounds, PFAS are regarded as highly toxic and extraordinarily persistent chemicals that pervasively contaminate human blood and wildlife throughout the world. They are therefore regarded as PBT (persistent, bioaccumulative, and toxic) chemicals. Two comprehensive methods have been developed for determination of eleven of the most environmentally relevant PFAS (seven perfluoroalkylcarboxylates, two perfluoroalkylsulfonates, and two perfluoroctanesulfonamides) in aqueous samples. The compounds were isolated by liquid–liquid extraction (LLE) and solid-phase extraction (SPE), and identification and quantification of the target analytes were achieved by liquid chromatography–electrospray ionization–tandem mass spectrometry (LC–ESI–MS–MS). With LLE detection limits ranged from 0.26 to 0.62 ng L⁻¹ for enrichment of 900-mL water samples; recovery of PFAS with a carbon chain longer than C₇ was excellent (80–93%). With SPE, carboxylates with carbon chains <C₁₀ could be extracted efficiently (70–98%) under acidic conditions, and PFOS and PFOSA could be extracted efficiently (81% and 96%, respectively) under basic conditions, resulting in MDLs between 0.25 and 0.64 ng L⁻¹. The LLE method was applied successfully to Austrian wastewater effluent samples.     

On-line preconcentration of perfluorooctanoic acid and perfluorooctanesulfonic acid by nonaqueous capillary electrophoresis

Separation of major environmental pollutants as perfluorooctanoic acid (PFOA) and perfluorooctanesulfonic acid (PFOS) by capillary electrophoresis is reported for the first time. It is not possible to resolve the solutes in an aqueous media. However, the use of methanol and acetonitrile as the background electrolyte (BGE) solvents allowed their rapid separation in an uncoated capillary. A major effort was put into BGE optimization in respect to both separation efficiency and detection for further on‐line preconcentration. 5 mmol.L^?1 naphthalene‐1‐sulfonic acid and 10 mmol.L^?1 triethylamine dissolved in ACN/MeOH (50:50 v/v) provided best separation and detection conditions. Next, the large‐volume sample stacking and the field‐amplified sample injection were applied and compared. Large‐volume sample stacking improved limits of detection (LODs) with regard to the standard injection by 69 times for PFOA and 143 times for PFOS with LODs of 280 and 230 nmol.L^?1, respectively. Field‐amplified sample injection improved LODs 624 times for PFOAand 806 times for PFOS with LODs 31 and 40 nmol.L^?1, respectively. Both preconcentration methods showed repeatabilities of migration times less than 1.2% RSD intraday and 6.6% RSD interday. The method was applied on PFOA and PFOS analysis in a sample of river water treated with solid‐phase extraction, which further improved LOD toward 5.6 × 10^?10 mol.L^?1 for PFOS and 6.4 × 10^?10 mol.L^?1 for PFOA and allows the method to be used for river water contamination screening or decomposition studies.     

Photocatalytic Degradation of Palm Oil Mill Effluent (POME) Waste Using BiVO4 Based Catalysts

Disposal of palm oil mill effluent (POME), which is highly polluting from the palm oil industry, needs to be handled properly to minimize the harmful impact on the surrounding environment. Photocatalytic technology is one of the advanced technologies that can be developed due to its low operating costs, as well as being sustainable, renewable, and environmentally friendly. This paper reports on the photocatalytic degradation of palm oil mill effluent (POME) using a BiVO₄ photocatalyst under UV-visible light irradiation. BiVO₄ photocatalysts were synthesized via sol-gel method and their physical and chemical properties were characterized using several characterization tools including X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), surface area analysis using the BET method, Raman spectroscopy, electron paramagnetic resonance (EPR), and UV-Vis diffuse reflectance spectroscopy (UV-Vis DRS). The effect of calcination temperature on the properties and photocatalytic performance for POME degradation using BiVO₄ photocatalyst was also studied. XRD characterization data show a phase transformation of BiVO₄ from tetragonal to monoclinic phase at a temperature of 450 °C (BV-450). The defect site comprising of vanadium vacancy (V_v) was generated through calcination under air and maxima at the BV-450 sample and proposed as the origin of the highest reaction rate constant (k) of photocatalytic POME removal among various calcination temperature treatments with a k value of 1.04 × 10⁻³ min⁻¹. These findings provide design guidelines to develop efficient BiVO₄-based photocatalyst through defect engineering for potential scalable photocatalytic organic pollutant degradation.     

Combining Coagulation and Electrocoagulation with UVA-LED Photo-Fenton to Improve the Efficiency and Reduce the Cost of Mature Landfill Leachate Treatment

This study focused on the reduction of the treatment cost of mature landfill leachate (LL) by enhancing the coagulation pre-treatment before a UVA-LED photo-Fenton process. A more efficient advanced coagulation pretreatment was designed by combining conventional coagulation (CC) and electro-coagulation (EC). Regardless of the order in which the two coagulations were applied, the combination achieved more than 73% color removal, 80% COD removal, and 27% SUVA removal. However, the coagulation order had a great influence on both final pH and total dissolved iron, which were key parameters for the UVA-LED photo-Fenton post-treatment. CC (pH = 5; 2 g L⁻¹ of FeCl₃6H₂O) followed by EC (pH = 5; 10 mA cm⁻²) resulted in a pH of 6.4 and 100 mg L⁻¹ of dissolved iron, whereas EC (pH = 4; 10 mA cm⁻²) followed by CC (pH = 6; 1 g L⁻¹ FeCl₃6H₂O) led to a final pH of 3.4 and 210 mg L⁻¹ dissolved iron. This last combination was therefore considered better for the posterior photo-Fenton treatment. Results at the best cost-efficient [H₂O₂]:COD ratio of 1.063 showed a high treatment efficiency, namely the removal of 99% of the color, 89% of the COD, and 60% of the SUVA. Conductivity was reduced by 17%, and biodegradability increased to BOD₅:COD = 0.40. With this proposed treatment, a final COD of only 453 mg O₂ L⁻¹ was obtained at a treatment cost of EUR 3.42 kg COD⁻¹.     

One-Step Route to Fe2O3 and FeSe2 Nanoparticles Loaded on Carbon-Sheet for Lithium Storage

Iron-based anode materials, such as Fe₂O₃ and FeSe₂ have attracted widespread attention for lithium-ion batteries due to their high capacities. However, the capacity decays seriously because of poor conductivity and severe volume expansion. Designing nanostructures combined with carbon are effective means to improve cycling stability. In this work, ultra-small Fe₂O₃ nanoparticles loaded on a carbon framework were synthesized through a one-step thermal decomposition of the commercial C₁₅H₂₁FeO₆ [Iron (III) acetylacetonate], which could be served as the source of Fe, O, and C. As an anode material, the Fe₂O₃@C anode delivers a specific capacity of 747.8 mAh g⁻¹ after 200 cycles at 200 mA g⁻¹ and 577.8 mAh g⁻¹ after 365 cycles at 500 mA g⁻¹. When selenium powder was introduced into the reaction system, the FeSe₂ nano-rods encapsulated in the carbon shell were obtained, which also displayed a relatively good performance in lithium storage capacity (852 mAh g⁻¹ after 150 cycles under the current density of 100 mA·g⁻¹). This study may provide an alternative way to prepare other carbon-composited metal compounds, such as FeN_x@C, FeP_x@C, and FeS_x@C, and found their applications in the field of electrochemistry.     

Sm0.5Sr0.5Co1−xNixO3−δ—A Novel Bifunctional Electrocatalyst for Oxygen Reduction/Evolution Reactions

The development of non-precious metal catalysts with excellent bifunctional activities is significant for air–metal batteries. ABO₃-type perovskite oxides can improve their catalytic activity and electronic conductivity by doping transition metal elements at B sites. Here, we develop a novel Sm_0.5Sr_0.5Co_1−xNi_xO_3−δ (SSCN) nanofiber-structured electrocatalyst. In 0.1 M KOH electrolyte solution, Sm_0.5Sr_0.5Co_0.8Ni_0.2O_3−δ (SSCN82) with the optimal Co: Ni molar ratio exhibits good electrocatalytic activity for OER/ORR, affording a low onset potential of 1.39 V, a slight Tafel slope of 123.8 mV dec⁻¹, and a current density of 6.01 mA cm⁻² at 1.8 V, and the ORR reaction process was four-electron reaction pathway. Combining the morphological characteristic of SSCN nanofibers with the synergistic effect of cobalt and nickel with a suitable molar ratio is beneficial to improving the catalytic activity of SSCN perovskite oxides. SSCN82 exhibits good bi-functional catalytic performance and electrochemical double-layer capacitance.     

Solid-phase extraction of PFOA and PFOS from surface waters on functionalized multiwalled carbon nanotubes followed by UPLC–ESI-MS

This is the first report on the analytical application of multiwalled carbon nanotubes (MWCNTs) as solid-phase extraction (SPE) sorbents for determination in surface waters, at the nanograms per litre level, of perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS), the two predominant contaminants among the perfluorinated compounds detected. After the preconcentration step, the quantification was achieved by ultraperformance liquid chromatography–electrospray ionization mass spectrometry. To increase the extraction efficiency towards these amphiphilic compounds, MWCNTs were derivatized with amino-terminated alkyl chains, thus producing a mixed-mode material (MWCNT-R-NH₂) combining hydrophobic affinity and anion-exchange properties. Experiments with distilled, tap and river water (pH 3) spiked at different concentrations (10, 15, 30, 100, 200 and 500 ng L^-1) provided absolute recoveries in the range 71–102 % (n?=?3, relative standard deviations less than 10 %). Analytes were eluted in a single fraction with 6 mL methanol (3?×?10^-4 M NaOH). The within-laboratory reproducibility of the MWCNT-R-NH₂ SPE sorbent was evaluated with raw river water, and relative standard deviations less than 15 % were obtained (n?=?4). Preconcentration factors up to 125 (500-mL sample) made it possible to quantify PFOA and PFOS at low nanograms per litre levels in naturally contaminated river water. The method quantification limits of 10 ng L^-1 for PFOA and 15 ng L^-1 for PFOS were well below the advisory levels for drinking and surface waters. Comparison with non-derivatized MWCNTs highlighted the role of functionalization in improving the adsorption affinity towards these contaminants. MWCNT-R-NH₂ maintained their extraction capability for at least eight repeated adsorption/desorption cycles.     

LDPE Transformation by Exposure to Sequential Low-Pressure Plasma and TiO2/UV Photocatalysis

Low-density polyethylene (LDPE) sheets (3.0 ± 0.1 cm) received sequential treatment, first by the action of direct-current low-pressure plasma (DC-LPP) with a 100% oxygen partial pressure, 3.0 × 10⁻² mbar pressure, 600 V DC tension, 5.6 cm distance, 6-min treatment. Then, sheets were submitted to TiO₂ photocatalysis at UV radiation at 254 nm (TiO₂/UV) with a pH value of 4.5 ± 0.2 and a TiO₂ concentration of 1 gL⁻¹. We achieved a complementary effect on the transformation of LDPE films. With the first treatment, ablation was generated, which increased hydrophilicity. With the second treatment, the cavities appeared. The changes in the LDPE sheets’ hydrophobicity were measured using the static contact angle (SCA) technique. The photocatalytic degradation curve at 400 h revealed that the DC-LPP photocatalysis sequential process decreased SCA by 82°. This was achieved by the incorporation of polar groups, which increased hydrophilicity, roughness, and rigidity by 12 and 38%, respectively. These sequential processes could be employed for LDPE and other material biodegradation pretreatment.     

Direct and Indirect Bactericidal Effects of Cold Atmospheric-Pressure Microplasma and Plasma Jet

The direct and indirect bactericidal effects of dielectric barrier discharge (DBD) cold atmospheric-pressure microplasma in an air and plasma jet generated in an argon-oxygen gas mixture was investigated on Staphylococcus aureus and Cutibacterium acnes. An AC power supply was used to generate plasma at relatively low discharge voltages (0.9–2.4 kV) and frequency (27–30 kHz). Cultured bacteria were cultivated at a serial dilution of 10⁻⁵, then exposed to direct microplasma treatment and indirect treatment through plasma-activated water (PAW). The obtained results revealed that these methods of bacterial inactivation showed a 2 and 1 log reduction in the number of survived CFU/mL with direct treatment being the most effective means of treatment at just 3 min using air. UV–Vis spectroscopy confirmed that an increase in treatment time at 1.2% O₂, 98.8% Ar caused a decrease in O₂ concentration in the water as well as a decrease in absorbance of the peaks at 210 nm, which are attributed NO₂⁻ and NO₃⁻ concentration in the water, termed denitratification and denitritification in the treated water, respectively.