Quantitative capillary zone electrophoresis of inorganic anions

Despite the availability of commercial capillary electrophoresis systems for over ten years, where quantitative analysis is required, capillary zone electrophoresis (CZE) has often failed to replace ion chromatography as the method of choice for a large number of analytes, not least inorganic anions. To investigate the reasons for this apparent failing, a review is presented of work that has been carried out to-date involving the quantitative application of CZE to the determination of inorganic anions in industrial and environmental samples. This review summarizes work both investigating and improving the quantitative aspects of the CZE of inorganic anions. A complete survey of how CZE has been applied to the determination of inorganic anions in real samples is given, including what, if any, analytical performance parameters were investigated and quoted, and if quality assurance data and validation methods were briefly considered, thoroughly investigated or simply ignored.     

Separation of inorganic anions in acidic solution by capillary electrophoresis

Inorganic anions are almost always determined by capillary electrophoresis (CE) at an alkaline pH, so the analytes will be fully ionized. However, a long-chain quaternary ammonium salt usually must be added as a flow modifier to the carrier electrolyte to reverse the direction of the electroosmotic flow. By working at a sufficiently acidic pH, the electroosmotic flow in fused-silica capillaries is virtually eliminated, and anions can be separated simply by differences in their electrophoretic mobilities. Excellent separations were obtained for AuCl₄⁻ and the chloro complexes of platinum group elements in HCl solution at pH 2.0 to 2.4. No additional buffer or flow modifier was needed. This CE technique is an excellent way to follow slow hydrolytic reactions in which one or more of the chloride ligands is replaced by water. Sharp peaks and good separations were also obtained for MnO₄⁻, VO₃⁻, chromate, molybdate, ferrocyanide, ferricyanide and stable complex ions such as chromium oxalate (CrO₃³⁻).     

New preconditioning strategy for the determination of inorganic anions with capillary zone electrophoresis using indirect UV detection

It is widely accepted that preconditioning procedures are indispensable in capillary electrophoresis in order to achieve reproducibility of migration times and peak areas. Several preconditioning strategies have been employed for electrophoretic determinations of inorganic anions using indirect UV detection including simple flushing with buffer or alkaline or acid pre-rinsing followed by flushing with electrolyte. We investigated the influence of various preconditioning strategies on the reproducibility of migration times and peak areas of inorganic anions. The electrolyte systems for indirect UV detection were based on pyromellitic acid and chromic acid respectively as UV absorbing probes and hexamethonium hydroxide as electroosmatic flow modifier. Preconditioning agents under investigation were electrolyte buffer, NaOH, HCl and the free acids of the UV absorbing probes. Investigations showed that reproducibility of migration times and peak areas can be significantly improved by acid pre-rinsing using the corresponding acid of the UV absorbing probes compared to preconditioning by flushing the capillary with buffer. In contrast to acid pre-rinsing using hydrochloric acid no interfering signals within the migration time window of inorganic anions under investigation can be observed. The optimized preconditioning procedure yields relative standard deviations of migration times less than 0.25% (n=10). Relative standard deviations of corrected peak areas were below 5% applying acid preconditioning using pyromellitic acid.     

Ion exchange-based preconcentration for the determination of anions by capillary electrophoresis

In the present paper a capillary zone electrophoresis (CZE)-compatible preconcentration technique for anions, based on ion exchange, is described. The described preconcentration approach has found limited use until recently because of the inherent elution step that leads to contamination of the sample with eluent components. In this paper, we describe an improved anion exchange-based preconcentration technique in which contamination of the sample with the eluent constituents, which occurs during anion elution from the preconcentration column, is eliminated by on-line chemical suppression on a packed-bed suppressor column. In the present communication, the basic principles of the proposed anion enrichment system are presented. The system was optimized, resulting in a minimal additional dilution of the eluted sample plug. This was achieved by the use of a computer-controlled, sensing/switching system. The effectiveness of the developed method was later tested on the determination of some anions in a synthetic sample using CE apparatus.     

Electroosmotic flow controllable coating on a capillary surface by a sol-gel process for capillary electrophoresis

A simple coating procedure employing a sol-gel process to modify the inner surface of a bare fused-silica capillary with a positively charged quaternary ammonium group is established. Scanning electron microscopic studies reveal that a smooth coating with 1 to approximately 2 microm thickness can be obtained at optimized coating conditions. With 40 mM citrate as a running electrolyte, the plot of electroosmotic flow (EOF) versus pH shows a unique three-stage EOF pattern from negative to zero and then to positive over a pH range of 2.5 to 7.0. At pH above 5.5, the direction of the EOF is from the anode to the cathode, as is the case in a bare fused-silica capillary, and the electroosmotic mobility increases as the pH increases. However, the direction of the EOF is reversed at pH below 4.0. Over the pH range of 4.0 to 5.5, zero electroosmotic mobility is obtained. Such a three-stage EOF pattern has been used to separate six aromatic acids under suppressed EOF and to separate nitrate and nitrite with the anions migrating in the same direction as the EOF. The positively charged quaternary ammonium group on the coating was also utilized to minimize the adsorption problem during the separation of five basic drugs under suppressed EOF and during the separation of four basic proteins with the cations migrate in the opposite direction as the EOF. Also, the stability and reproducibility of this column are good.     

Simultaneous separation of inorganic anions and cations by capillary zone electrophoresis

A new capillary electrophoretic approach for simultaneous separation of fast anions and cations is demonstrated. Indirect UV detection at 214 nm in conjunction with electromigration sampling from both ends of the capillary was developed. Two electrolyte systems based on imidazole-nitrate and copper(II)-ethylenediamine-nitrate were investigated for the simultaneous separation of chloride, sulphate, hydrocarbonate, potassium, ammonium, calcium, sodium and magnesium ions. Experimental parameters that were evaluated included a nature of UV chromophore, pH of electrolyte, a nature of complexing agent. The method permits the excellent separation of three anions and five cations in only 4 min using electrolyte system containing 2.5 mmol l⁻¹ Cu(NO₃)₂, 5 mmol l⁻¹ ethylenediamine and 1 mmol l⁻¹ fumaric acid at pH 8.5 adjusted with tetraethylammonium hydroxide.     

Determination of inorganic anions in Kraft pulping liquors by capillary electrophoresis

Various sulfur containing anions (sulfate, sulfite, and thiosulfate) in Kraft pulping process liquors are determined by capillary electrophoresis. In addition, other inorganic anions (hydroxide, chloride, oxalate, carbonate) are analyzed with the developed method. Through optimization of the separation conditions it is possible to simultaneously determine these anionic species in pulping liquors with direct and indirect UV detection at 185, 214, and 254 nm. To ensure short separation times a migration of the anionic analytes in the same direction as the electroosmotic flow (co-electroosmotic CE) is established by reversal of the electroosmotic flow with 1,5-dimethyl-1,5-diazaundecamethylene polymethobromide (hexadimethrine bromide; HDB; polybrene™) which is added to the electrolyte as EOF modifier. The impact of acetonitrile as organic modifier to improve the selectivity of the anionic analytes is also investigated. The developed method is then applied to analyze and quantify various anions in pulping liquors (white and black liquors). By simultaneously determining the hydroxide concentration it is possible to calculate effective alkalinity and sulfidity with the measured concentrations without the need of volumetric methods.     

Factors affecting selectivity of inorganic anions in capillary electrophoresis

Capillary zone electrophoretic separations of inorganic anions are largely governed by the intrinsic (infinite dilution) mobility of the anion. This in turn is a function of the hydrodynamic friction caused by the size of the ion and the dielectric friction caused by the charge density of the anion re-orienting the surrounding solvent. The influence of these factors on the mobility of anions is examined in both water and nonaqueous solvents. The influence of other experimental parameters, such as ionic strength, ion association, electroosmotic flow modifier concentration, and the addition of complexing agents such as polymeric cations, cyclodextrins, crown ethers and cryptands are also reviewed. From this discussion, some rules of thumb as to when different approaches will be most effective are drawn.     

The use of macrocycles as electroosmotic flow modifiers in the separation of inorganic anions by capillary electrophoresis

In a novel approach to the use of macrocycles in separation systems, we report the use of macrocyclic ligands as electroosmotic flow modifiers for the separation of inorganic anions by capillary electrophoresis (CE). Inorganic anions were successfully separated through the use of 18-crown-6 or cryptand 2.2.2. as electroosmotic flow modifiers. We found that for our CE system, use of a macrocycle as the modifier resulted in better baseline stability and better efficiency than the commonly used modifier DETA. In our system, the separation efficiency and electroosmotic flow varied according to the pH of the buffer and the affinity of the macrocycle for the buffer metal cation. Results for sodium- and potassium-based buffers show that for the cryptand, pH plays a role in determining the amount of macrocycle-metal complex formed. Separations of a 12 anion standard illustrate these results. In addition, we report the effect of concentration of both macrocycle and metal ion on complex formation and resultant electroosmotic flow modification. Relationships between the macrocycle-metal complex, the buffer medium, the efficiency of separation, and the migration times of the analytes are discussed, and theoretical interpretations presented.     

Cationic diazacrown ethers as selectors for the separation of inorganic anions by capillary electrophoresis

Two types of positively charged diazacrown ether derivatives involving two quaternary ammonium ions in the 12- and 18-membered rings have been investigated as selectors for the separation of inorganic anions by capillary electrophoresis. Both the cationic macrocycles largely affected the electrophoretic mobilities of analyte anions, and a group of seven inorganic anions examined in this study was completely separated in less than 2.2 min by the use of the low concentration of the additives. From the determination of ion association constants, the cationic diazacrowns were found to show greater electrostatic interaction with divalent anions than with monovalent ones.     

Comparison between capillary electrophoresis and ion-chromatography for analysis of inorganic anions

Separation and detection of some selected inorganic anions with capillary electrophoresis are shown. The anions are separated in microbore capillaries (25 m* 0.2 m) and detected with a UV-detector. Results are compared with the method of ion exchange chromatography. In consideration of the most important physical and chemical parameters an easy kind of computer simulation for such electropherograms was developed.To get optimal results of separation and UV-detection in capillary electrophoresis some parameters of the device HPE 100, i.e. loading time in the electrokinetic sample injection mode and the running voltage are varied. The behaviour of absorption in the UV region of the chosen anions as well as the influence of pH values in retention behaviour are investigated. There is a simple way to calculate the electrophoretic mobilities from known retention times. Approximate limits of detection for all anions and for each technique are given.     

Approaches to enhancing the sensitivity of capillary electrophoresis methods for the determination of inorganic and small organic anions

One of the major problems facing the development of capillary electrophoresis (CE) is the relatively high limits of detection when compared to traditional high-performance liquid chromatographic (HPLC) methods. While the use of an alternative detector can offer better sensitivity, a more universal approach is sample preconcentration. Numerous on-line methods have been developed to improve the sensitivity of CE, and are based on electrophoretic principles, chromatographic principles, or a combination of both. This review will discuss all forms of on-line preconcentration methods for CE, with emphasis given to those that have shown particular merit when applied to inorganic and small organic anions.     

Determination of inorganic anions in human saliva by zwitterionic micellar capillary electrophoresis

Capillary electrophoresis (CE) using sulfobetaine-type zwitterionic micelles as the background electrolyte (BGE) has been used to determine inorganic anions in human saliva. The zwitterionic micelles resulted in unique migration behavior for the separation of inorganic anions. They also prevented adsorption of proteins on the inner wall of the capillary. These properties of the zwitterionic micelles enabled the direct determination of inorganic anions in human saliva. Three species of inorganic anions, NO₂ ^–, NO₃ ^–, and SCN^–, were found in real samples and the analysis was achieved within 3 min. Direct UV-absorption was used as the detection method and the detection limits for these anions were 2.0, 1.0, and 5.0 μmol L^–1, respectively (0.09, 0.06, and 0.30 μg mL^–1).     

Simultaneous determination of inorganic anions, carboxylic and aromatic carboxylic acids by capillary zone electrophoresis with direct UV detection

Co-electroosmotic capillary zone electrophoresis (CZE) with direct UV detection was developed for simultaneous determination of inorganic anions, carboxylic and aromatic carboxylic acids. These solutes were separated using a 30 mM phosphate buffer containing 1.0 mM tetradecyltrimethylammonium bromide (TTAB) and 20% (v/v) acetonitrile at pH of 6.5 and directly detected by UV at 190 nm. Calibration curves were linear in the range 0.01-2.0 mM, depending of the solutes. The detection limits ranged from 1.0 to 8.0 microM and the relative standards deviations (n=5) in range from 1.9 to 3.6% for the peak area. The proposed method was used to determine inorganic anions and carboxylic and aromatic acids in soil and plant tissue extracts.     

Identification and determination of inorganic anions in real extracts from pre- and post-blast residues by capillary electrophoresis

Fast, selective, and sensitive analysis of inorganic anions is compulsory for the identification of explosives in post-blast or environmental samples. For the last twenty years, capillary electrophoresis (CE) has become a valuable alternative to ion chromatography (IC) for the analysis of inorganic-based explosives because of its low running costs and its simplicity of use. This article focuses on the development and validation of a CE method for the simultaneous analysis of 10 anions (chloride, nitrite, nitrate, thiosulphate, perchlorate, chlorate, thiocyanate, carbonate, sulphate, and phosphate) which can be found in post-blast residues, plus for the first time azide anion, possibly present in the composition of detonators, and the internal standard (formate) in 20 min total runtime. Intermediate precisions were 2.11% for normalized areas and 0.72% for normalized migration times. Limits of detection close to 0.5 ppm for all anions were obtained with the use of preconcentration techniques, thanks to a fast and simple sample preparation allowing the analysis of a large variety of matrices with the developed generic CE method. The matrix effects were statistically studied for the first time in the explosive field for different matrices, containing interfering anions and cations, sometimes at high levels. In fact, no significant matrix effect occurred (tests with blank matrix extracts of soil, cloth, glass, plastic, paper, cotton, and metal). Finally, analyses of real post-blast residues and real detonator extracts were performed. The CE results were compared with those obtained with the IC method used routinely and showed excellent correlation.     

Electroosmotic flow modulation in capillary electrophoresis by organic cations from ionic liquids

This paper describes the ability of several ionic liquids cations for electroosmotic flow modulation in capillary electrophoresis. Organic salts based on phosphonium, sulfonium, cysteinium, ammonium, and guanidinium cations were selected to study this property. In addition, the synergistic effect of these compounds in cyclodextrin chiral separation was also evaluated. In comparison with most studied imidazolium-based ionic liquids, several of the cations studied, are stronger modifiers in terms of electroosmotic flow (EOF) modulation. Phosphonium-based compounds and tri-octyl methylammonium chloride ([Aliquat]Cl) had the strongest ability to reverse EOF both in acidic and in basic conditions and had the lowest EOF reversal concentrations in the presence of hydroxypropyl-β-cyclodextrin. EOF modulation ability of phosphonium cations also contributed to the improvement of chiral separation of DL-propranolol by hydroxypropyl-β-cyclodextrin at lower concentrations in comparison with most commonly used EOF modulators such as tetrabutylammonium phosphate.     

Determination of inorganic anions in human saliva by zwitterionic micellar capillary electrophoresis

Capillary electrophoresis (CE) using sulfobetaine-type zwitterionic micelles as the background electrolyte (BGE) has been used to determine inorganic anions in human saliva. The zwitterionic micelles resulted in unique migration behavior for the separation of inorganic anions. They also prevented adsorption of proteins on the inner wall of the capillary. These properties of the zwitterionic micelles enabled the direct determination of inorganic anions in human saliva. Three species of inorganic anions, NO2-, NO3-, and SCN-, were found in real samples and the analysis was achieved within 3 min. Direct UV-absorption was used as the detection method and the detection limits for these anions were 2.0, 1.0, and 5.0 micromol L(-1), respectively (0.09, 0.06, and 0.30 microg mL(-1)).     

Direct analysis of inorganic anions in samples with high salt content by capillary zone electrophoresis

Trace-level inorganic anions in seawater are separated efficiently by capillary zone electrophoresis using direct UV detection. The carrier electrolyte is 50 mM borate at pH 9.3 and contained 1.5M NaCl. This buffer solution is adopted to prevent interference from high concentrations of the chloride ion in seawater. No electro-osmotic flow reverser is used to shorten the analysis time. The experimental conditions such as the concentration of NaCl in the carrier electrolyte, capillary inner diameter, applied current, and temperature are optimized. Linear plots are obtained in the concentration range of 0.1 to 20 microg/mL. The quantitation limits of the anions are in the order of 0.02 to 0.1 microg/mL. The proposed method may be applicable to the determination of inorganic anions in other environmental samples and effluents of a power plant.     

Routine determination of major anions in atmospheric aerosols by capillary electrophoresis

Capillary electrophoresis (CE) with indirect UV detection utilizing a pyromellitate-based electrolyte was used for the routine analysis of major anions in atmospheric aerosols collected on filters with high-volume (Hi-Vol) samplers. The long-term reliability of the CE system was checked over an 8-month period during which over 2900 samples were analyzed. In addition, approximately 1100 samples were analyzed in parallel by ion chromatography (IC). It has been shown that acceptable analytical performance can be routinely obtained. The agreement between the CE and IC results is good, generally better than 20% at concentrations larger than 1 mg l⁻¹.     

Analysis of organic acids and inorganic anions in beverage drinks by capillary electrophoresis

To meet the need for a new and validated analytical method for simultaneous determination of inorganic and organic acid anions in beverage drinks, a capillary zone electrophoresis (CZE) procedure had been developed based on a new background electrolyte (BGE) system containing 3 mmol/L 1,3,5-benzenetricarboxylic acid (BTA), 15 mmol/L tris(hydroxymethyl)aminomethane and 1.5 mmol/L tetraethylenepentamine (TEPA) at pH 8.4. Baseline separation of anions commonly found in beverage drinks could be achieved in less than 14 min with indirect UV detection at 240 nm. Comigration problems for hydroxycarboxylic acids could be solved using TEPA as BGE additive. The results indicate excellent repeatability for migration time (RSD, 0.27-0.67%, n = 5) and good precision for both peak height (RSD, 3.2-4.2%, n = 5) and peak area (RSD, 3.1-4.5%, n = 5). Under the optimized conditions and using corrected peak area for quantitation, an excellent linear dynamic range (with correlation coefficient > 0.997 in a concentration range from 0.005 to 2.0 mmol/L) and low detection limit (1-4 micro mol/L) were obtained for all the anions investigated. The applicability and reliability of the CE procedure developed were established by parallel method determination using established ion chromatography procedure for the analysis of inorganic and organic acid anions in orange juice and wine samples. Our CZE procedure provided a sensitive and economic technique for simultaneous determination of inorganic and organic acid anions in orange juice, red and white wine samples.