Column Solid-Phase Extraction with 2-Acetylmercaptophenyldiazoaminoazobenzene (AMPDAA) Impregnated Amberlite XAD-4 and Determination of Trace Heavy Metals in Natural Waters by Flame Atomic Absorption Spectrometry

A column solid-phase extraction (SPE) preconcentration method was developed for the determination of Cd, Co, Cu, Ni and Zn ions in natural water samples by flame atomic absorption spectrometry. The procedure is based on the retention of analytes in the form of 2-acetylmercaptophenyldiazoaminoazobenzene (AMPDAA) complexes on a short column of AMPDAA-XAD-4 resin from buffered sample solution and subsequent elution with hydrochloric acid plus sodium chloride. Important SPE parameters were optimized using model solutions. The loading half-time, t_1/2, for Cd, Co, Cu and Zn was found to be less than 5min, and for Ni the value was 12min. The detection limit for Cd, Co, Cu, Ni and Zn was 0.028, 0.064, 0.042, 0.023 and 0.16µgL^–1, respectively, and the quantification limit was 0.043, 0.11, 0.099, 0.044 and 0.29µgL^–1, respectively. The AMPDAA-XAD-4 resin has good selectivity for Cd, Co, Cu, Ni and Zn over several electrolytes, especially over earth alkaline metals with tolerance limits of 0.05molL^–1. The method was validated by analysing a standard reference material (GBW 08301), and it was found that the results agree with those quoted by the manufactures. The developed method was applied to the determination of trace metal ions in tap water and river water samples with satisfactory results.     

Determination of trace heavy metals in waters by flame atomic absorption spectrometry after preconcentration with 2,4-dinitrophenyldiazoaminoazobenzene on Amberlite XAD-2

A new column, solid-phase extraction (SPE), preconcentration method was developed for determination of Cd, Co, and Cu ions in natural water samples by flame atomic absorption spectrometry. The procedure is based on the retention of analytes in the form of 2,4-dinitrophenyldiazoaminoazobenzene (DNDAA) complex on a mini column of DNDAA-XAD-2 resin. The effects of pH, eluent type, eluent concentration, eluent volume, resin quantity, sample volume, sample flow rate, and matrix ions (Na, Ca, and Mg) were investigated on the recovery of the metals using model solutions. The detection limit for Cd, Co, and Cu was 0.062, 0.084, and 0.057 μg L⁻¹ and the quantification limit was 0.17, 0.24, and 0.12 μg L⁻¹ respectively. The method was validated by the analysis of a certified reference material with the results being in agreement with those quoted by manufactures. The developed method was applied to the determination of trace metal ions in tap water, river water samples with satisfactory results.     

键合4-(2-吡啶偶氮)-间苯二酚螯合树脂分离富集-火焰原子吸收法测定蔬菜中痕量镉(Ⅱ)

本文合成了Amberlite XAD-4键合4-(2-吡啶偶氮)-间苯二酚螯合树脂,并考察了其对痕量镉(Ⅱ)的吸附性能。探讨了溶液pH、洗脱剂和干扰离子等对镉(Ⅱ)分离富集的影响。树脂吸附容量为4.7mg/g,吸附的镉(Ⅱ)用5mL 2mol/L HNO3乙醇溶液洗脱,火焰原子吸收法测定。在最佳实验条件下,回收率为94.4%～97.9%,相对标准偏差在1.7%～2.7%之间。方法可用于蔬菜中镉(Ⅱ)的测定。     

On-Line Preconcentration and Determination of Cadmium, Cobalt and Nickel in Food Samples by Flame Atomic Absorption Spectrometry Using a New Functionalized Resin

A new chelating sorbent has been developed using Amberlite XAD-2 resin anchored with pyrocatechol through the –CH₂– group. This sorbent, characterised by elemental analysis and infrared (IR) spectra, was used as a packing material for a minicolumn in an on-line preconcentration system for cadmium, cobalt and nickel determination. Metal ions were sorbed in the minicolumn, from which it could be eluted directly to the nebulizer-burner system of the flame atomic absorption spectrometer (FAAS). Metals can be eluted from the minicolumn with 0.50 mol L⁻¹ HCl or HNO₃. The enrichment factors were 22 (Cd), 23 (Co) and 25 (Ni), for 60 s preconcentration time, and 44 (Cd), 40 (Co) and 48 (Ni), if 180 s preconcentration time was used. Under the optimum conditions, the procedure allowed the determination of cadmium, cobalt and nickel with detection limits of 0.27, 0.59 and 1.29 μg L⁻¹, respectively, when preconcentration periods of 180 s were used. The accuracy of the procedure was sufficient and evaluated by analysing certified reference materials. The method was applied to the analysis of food samples (black tea and rice flour).     

Silica Gel Loaded with <Emphasis Type="Italic">o</Emphasis>-Dihydroxybenzene: Design,Metal Sorption Equilibrium Studies and Application to Metal Enrichment Prior to Determination by Flame Atomic Absorption Spectrometry

The aminopropyl silica gel (APSG) prepared by reaction of activated silica gel with 3-aminopropyltriethoxysilane on reaction with 3,4-dihydroxybenzaldehyde has resulted in a new chelating matrix, o-dihydroxybenzene (DHB) anchored silica gel, which is characterized by IR, TGA and elemental analyses. APSG is characterized with ¹³C CPMAS NMR spectroscopy. DHB anchored silica gel sorbs quantitatively (97.4–99.2% recovery) Cu(II), Pb(II), Fe(III), Zn(II), Co(II), Ni(II) and Cd(II) at pH 6.0–7.5, 5.0–7.0, 5.5–7.0, 6.0–8.0, 6.5–8.0, 5.5–7.0 and 6.5–7.5, respectively. The sorption capacity varies from 32 to 348µmolg^–1 and is highest for copper. Desorption was found to be quantitative with 1.0–3.0molL^–1 HCl/HNO₃ (for Pb). The optimum flow rate of the solution for quantitative sorption of metal ions on a column (10cm×10mm) packed with 1g of the modified silica gel is 1.0–4.0mLmin^–1, whereas for desorption it is 2.0 –4.0mLmin^–1. The tolerance limits for NaCl, NaBr, NaI, NaNO₃, Na₂SO₄, Na₃PO₄, humic acid, EDTA, ascorbic acid, citric acid, sodium tartrate, Ca(II) and Mg(II) in the sorption of all the seven metal ions are reported. The preconcentration factors are between 100 and 300 and t_1/2 values 17min. The present matrix coupled with FAAS has been used to enrich and determine the seven metal ions in river and tap water samples (RSD 1.4–7.0%) and in synthetic certified water samples SLRS-4 (NRC, Canada) with an RSD of 2.73–2.83%. The cobalt present in pharmaceutical vitamin tablets and Zn in milk powder was preconcentrated on DHB anchored silica gel and determined by FAAS (RSD of 2.00 to 2.72%).     

Determination of Iron(III), Cobalt(II) and Chromium(III) in Various Water Samples by Flame Atomic Absorption Spectrometry After Preconcentration by Means of Saccharomyces Carlsbergensis Immobilized on Amberlite XAD-4

A method for the determination of Fe(III), Co(II) and Cr(III) by flame atomic absorption spectrophotometry (FAAS) after preconcentrating on a column containing S. carlsbergensis immobilized on Amberlite XAD-4 has been developed. The optimum values of pH, amount of adsorbent, elution solution and flow rate of the sample solution were determined for the quantitative recovery of the analytes. The effect of interfering ions on the recovery of the analytes was also investigated. Under the optimum conditions, recoveries of Fe(III), Co(II) and Cr(III) by S. carlsbergensis immobilized on Amberlite XAD-4 were 99±2, 100±2 and 98±2% at 95% confidence level, respectively. The limit of detections for Fe(III), Co(II) and Cr(III) were 2.8, 3.9 and 7.4ngmL^–1, respectively. The proposed method was applied to the determination of the analytes in various water samples. The validity of the method was checked with spiked water samples. Fe(III), Co(II) and Cr(III) was determined with a relative error of less than 5%.     

Preconcentration and Determination of Copper(II) by Novel Solid-Phase Extraction and High-Resolution Continuum Source Flame Atomic Absorption Spectrometry

Amberlite XAD-4 modified with N-para-anisidine-3,5-di-tert-butylsalicylaldimine was investigated as a new chealting sorbent for the selective separation and preconcentration of Cu(II). The metal ion was retained by chemical sorption on the modified resin, eluted by hydrochloric acid, and determined by high-resolution continuum source flame atomic absorption spectrometry. The prepared resin was characterized for the solid-phase extraction of Cd²⁺, Co²⁺, Cr³⁺, Cu²⁺, Fe³⁺, Mn²⁺, Ni²⁺, Pb²⁺, and Zn²⁺ in a column. The influence of the pH, the mass of solid phase, eluent, flow rate, and sample volume was optimized. Using the optimum conditions, only Cu(II) showed quantitative sorption at the 95% confidence level, and the recoveries of the other metal ions were below 80%. A preconcentration factor 125 was obtained for Cu(II) with a limit of detection of 0.56?µg?L^?1. The method was used for the determination of Cu(II) in tap water, river water, tomato leaves, and fish. The relative standard deviation and the relative error were lower than 7%.     

Determination of Wear Metals in Marine Lubricating Oils by Microwave Digestion and Atomic Absorption Spectrometry

 The difficulties associated with the development of a microwave-assisted acid digestion of lubricating oils in determination of wear metals are presented. The interest of this sample treatment lies in its basis for determining the total metal contents with enough sensitivity by flame atomic absorption spectrometry (FAAS). It allows earlier diagnosis of the engine state than is obtained by the widely applied simple dilution procedure. Another advantage is the avoidance of contamination and loss of the metals to be determined. The procedure employs nitric acid and hydrogen peroxide in a four-stage programme. Fe, Cu, Cr and Pb are determined by FAAS as representative of engine wear. The limits of detection are 0.1 μg/g for Fe and Cr and 0.05 μg/g for Cu and Pb. A comparison with other procedures is presented for spiked samples. Different types of used lubricating oils supplied by an oil company were analysed to prove the suitability of the procedure proposed. Received November 11, 1998. Revision Februray 20, 1999.     

Enrichment and flame atomic absorption spectrometric determination of palladium using chelating matrices designed by functionalizing Amberlite XAD-2/16 and silica gel

Six chelating matrices have been prepared by anchoring 2,3-dihydroxypyridine (DHP) and 2-{[1-(3,4-dihydroxyphenyl)methylidene]amino}benzoic acid (DMABA) onto Amberlite XAD-2 and XAD-16 and 3,4-dihydroxybenzaldehyde (DHB), and iminodiacetic acid (IDA) onto silica gel. The materials were explored for enrichment of palladium followed by its determination with flame AAS. The optimum pH ranges for quantitative solid phase extraction by these matrices are from 4.0–5.5 to 5.5–7.0. The flow rates (column procedure) and concentration of HCl required for desorption have been optimized. Thiourea (∼3%) is essential for quantitative recovery of Pd. The t_1/2 values are between 5 and 15 min. The sorption capacity varies from 38 to 192 μmol g⁻¹ (highest for silica gel loaded with iminodiacetic acid). The preconcentration factors were found in the range 20–150. Tolerance limits of foreign species in the enrichment are reported. The enrichment procedures coupled with FAAS determinations were applied to synthetic solutions corresponding to standards GBW07293 and NIST SRM 2557 successfully.     

Determination of Trace Elements in Carbonaceous Samples by Graphite Furnace Atomic Absorption Spectrometry: Microwave Digestion Versus Slurry Sampling

 The determination of chromium, copper, manganese, nickel and vanadium in carbonaceous samples by slurry introduction graphite furnace atomic absorption spectrometry and after microwave assisted digestion are compared. Parameters such as atomization and pyrolysis temperatures, and surfactant concentration as well as the homogenization procedure were optimized. The slurries were prepared by mixing adequate amounts of the pulverized samples with 0.05% Triton X-100, sonicating for, at least, 40 seconds during the preparation to separate aggregates and for 20 seconds immediately before being autosampled. It was not necessary to use modifiers and calibration against aqueous standards was possible for all the elements. Coke, graphite and certified coal samples were analyzed, and no significant difference was observed using both procedures. Good agreement between found and certified values was obtained. Received January 24, 2000. Revision September 26, 2000.     

Flame Atomic Absorption Spectrometric Determination of Arsenic After Volatilization of As(III) with Chloride Ions

 The generation of volatile species of As(III) as a means to introduce arsenic into a flame atomic absorption spectrometer has been studied. The method is based on the reaction between As(III) and chloride ions in sulphuric acid medium. The reaction is performed in a discontinuous or batch mode. With this method 130 μl of a solution containing 17.5% (w/v) sodium chloride and As(III) are injected by a 500 ml.min⁻¹ N₂ carrier gas flow into 1 ml of concentrated sulphuric acid. The gaseous compounds generated are introduced into the spectrometer through the nebulizer and As is determined. Received October 3, 1998. Revision January 6, 1999.     

泡沫塑料富集-火焰原子吸收光谱法测定金矿石中金

采用聚氨酯泡塑富集硫脲洗脱-火焰原子吸收光谱法测定金矿石中金。对样品称样量、硫脲洗脱时间、磷酸三丁酯的吸附效果和铁元素的干扰等工作条件进行了优化,解决了泡沫塑料吸附效率低和铁元素的干扰等技术性难题,提高了分析结果的精密度和准确度,弥补了传统的泡沫塑料富集-火焰原子吸收光谱法测定金矿石中金量的不足,方法检出限为0.06 μg/g,测定范围为 0.2 μg/g～100 μg/g,测定结果与标准值符合性较好,无显著性差异,精密度(RSD, n = 9) 小于2%。方法具有快速、简便、实用等优点,分析误差满足常规化学分析法的要求,能满足金矿石中金量的快速、准确测定。     

双硫腙修饰纳米TiO2分离富集石墨炉原子吸收光谱法测定水样中痕量金属离子

建立了双硫腙修饰纳米TiO2分离富集-石墨炉原子吸收光谱法测定水样中痕量镉、铬和铅的新方法,优化了纳米TiO2-双硫腙对试样中这3种痕量物质的吸附和解吸条件。结果表明,在pH 5.0时,镉、铬和铅可被定量吸附,静态饱和吸附容量分别为13.3、5.5、21.8 mg/g。吸附的各种金属离子可用5 mL 0.1mol/L的硝酸完全洗脱。该方法对Cd2+、Cr3+和Pb2+的检出限(3σ,n=11)分别为0.18、0.51、1.92 ng/L,相对标准偏差分别为2.8%、2.3%和1.0%,加标回收率为96%～101%。该方法已成功应用于环境水样中镉、铬和铅的测定。     

Indirect Determination of Sulfide by Cold Vapor Atomic Absorption Spectrometry

A method for the determination of sulfide based on its interference with the determination of Hg by cold vapor atomic absorption spectrometry is described. The decrease in mercury absorbance at 253.7nm is proportional to the concentration of sulfide over the range of 10–320ngmL^–1. The limit of detection was found to be 7ngmL^–1 and the relative standard deviation (R.S.D.) for the determination of different concentrations of sulfide was in the range of 1.8–2.2%. This method was applied to the determination of sulfide in whole human blood after gas-phase separation.     

火焰原子吸收光谱法测定水样中铅含量的不确定度评定

通过采用火焰原子吸收光谱法测定水样中铅的不确定度各项来源和评定方法的分析,建立一种分析实验室不确定度的评定方法,使实验结果更有客观性和准确性.     

火焰原子吸收光谱法快速测定水性漆中镉

研究了水性漆中镉的原子吸收法分析。采用干灰化法处理漆片试样,硝酸消解,ＦＡＡＳ测定,加标回 在８７．８￣９６．４％     

火焰原子吸收光谱法测定电解铝用冰晶石中锂

含锂冰晶石取代锂盐添加到电解质中被广泛应用于电解铝工业,其质量直接影响到电解铝工业的电解效率、吨铝能耗高低和电解铝产品质量优劣。控制冰晶石中锂含量是保证产品质量和应对废旧电解质再生对氟化盐市场冲击的一个重要举措。通过在铂坩埚中加入一定量高氯酸在高温条件下加热冒烟赶氟后再加入盐酸酸化至盐类完全溶解,建立了波长670.80 nm处采用火焰原子吸收光谱法测定铝用冰晶石中锂含量的方法,避免了大量氟基体的干扰,选择一定量的铝钠基体匹配来保证测试灵敏度和准确性;通过加标回收实验得知锂的回收率为102%;锂元素校准曲线线性相关系数≥0.9994;锂的检出限为0.0065μg/mL;不同含量含锂冰晶石的锂标准偏差均小于0.01%,与电感耦合等离子体原子发射光谱(ICP-AES)法测定结果相一致。方法准确可靠、简单易操作,满足铝电解工业生产分析的需要。     

流动注射-火焰原子吸收光度法测定矿泉水中的锶

用流动注射离子交换系统于酸性条件下在线富集饮用天然矿泉水中的锶,火焰原子吸收光度法测定,共存成分无干扰,方法简便快速,富集倍数可随意调节。在 60 h～(-1)的进样频率下,灵敏度提高 17倍。用于矿泉水中锶的测定,当含量为 60～250 ng/ml时,相对标准偏差为 0.68％～0.94％。回收率为 94.4％～110.3％,检测限为 15ng/ml。     

Analysis of Tea for Metals by Flame and Graphite Furnace Atomic Absorption Spectrometry with Multivariate Analysis

The concentrations of iron, zinc, manganese, copper, chromium, nickel, lead, arsenic, and cadmium were determined using flame and graphite furnace atomic absorption spectrometry in nine herbal tea samples. Hawthorn, yarrow, elderflower, and bearberry are herbal teas for which the metal content has been rarely determined. The concentration of cadmium in St John’s wort exceeded the maximum permissible limit of 0.3?mg/kg. The metals were also determined in aqueous extracts following 5, 10, and 20?min of boiling and using different preparations, including acidification with lemon juice. The influence of these factors on metal release was demonstrated using multivariate analyses by redundancy analysis and principal component analysis. The metal release was not considerably affected by the boiling time, while the acidity of the medium was generally positively correlated. For the infusions, arsenic was detected only in acidified mint tea. The extraction efficiencies of metals were determined and classified as highly, moderately, and poorly extractable, with chromium showing largest variations.     

流动注射在线液—液萃取原子吸收光谱法测定生物样品中的铅

本文利用所设计的一种新型流动注射液－液萃取重力分相器，建立了流动注射液溶剂萃取原子吸收光谱法测定铅的新方法，详细地研究了流动注射在线萃取的实验条件及流路系统，方法的精密度和检出限分别为２．５％（ｎ＝１１）和２．８μｇ／Ｌ（ｋ＝３）。用拟定的方法测定了峰蛹，粮食等生物样品中的铅，结果与参考值相吻合。