Development of an efficient protein phosphatase-based colorimetric test for okadaic acid detection

Okadaic acid (OA), responsible for gastrointestinal problems, inhibits protein phosphatase 2A (PP2A). Therefore, the inhibition exerted by the toxin on PP2A could be used to detect the presence of OA in aqueous solution and in shellfish sample.In this work, two commercial PP2As (from ZEU Immunotec and Millipore) and one produced by molecular engineering (from GTP Technology) were tested. Enzymes were used in solution and also immobilized within a polymeric gel. In solution, best performances were obtained using PP2A purchased from ZEU Immunotec (Spain). OA was detected in aqueous solution in concentration as low as 0.0124 μg L⁻¹ using the enzyme from ZEU Immunotec whereas the detection limits were 0.47 μg L⁻¹ and 0.123 μg L⁻¹ with PP2As from Millipore and GTP Technology, respectively. Considering that the immobilization step contributes to stabilize the PP2A activity, enzymes were entrapped within a photopolymer and an agarose gel. These different polymeric matrices were optimized, tested and compared. Agarose gel seems to be a good alternative to the photopolymer largely used in our group. For instance, the IC₅₀ value obtained with the test based on PP2A from ZEU Immunotec immobilized within an agarose gel was 1.98 μg L⁻¹. This value was 1.8-fold lower than those obtained with the photopolymer test using the same enzyme. The proposed test is sensitive, fast and does not require expensive equipment. To evaluate the efficiency of the assay, PP inhibition tests based on PP2A from ZEU Immunotec in solution or immobilized within a gel were used for OA detection in contaminated shellfish.     

Sensitive and rapid chemiluminescence enzyme immunoassay for microcystin-LR in water samples

A highly sensitive, specific, simple, and rapid chemiluminescence enzyme immunoassay (CLEIA) was developed for the determination of microcystin-LR (MC-LR). Several physicochemical parameters such as the chemiluminescent assay mediums, the dilution ratio of MC-LR-OVA conjugate, monoclonal antibody concentration, and peroxidase labeled antibody concentration were studied and optimized. Under optimum conditions, calibration curve obtained for MC-LR had detection limits of 0.032 ± 0.003 μg L⁻¹, the 50% inhibition concentration (IC₅₀) was 0.20 ± 0.02 μg L⁻¹ and the quantitative detection range was 0.062-0.65 μg L⁻¹. The proposed methods was successfully applied to the monitoring of MC-LR in spiked water samples without significant effect of the matrix, and the recovery of MC-LR added to water samples at different concentrations ranged from 80% to 115% with the coefficients of variation (CVs) less than 9%. The LOD attained from the calibration curves and the results obtained for the real samples demonstrate the potential use of CLEIA as a screening tool for the analysis of MC-LR in environmental samples.     

Enzyme inhibition-based biosensor for the electrochemical detection of microcystins in natural blooms of cyanobacteria

An electrochemical biosensor for the detection of microcystin has been developed based on the inhibition of the protein phosphatase 2A (PP2A) by this cyanobacterial toxin. The enzyme has been immobilised by entrapment using a poly(vinyl alcohol) azide-unit pendant water-soluble photopolymer (PVA-AWP). Electrode supports and immobilisation conditions have been optimised by colorimetric assays, the highest immobilisation yields being obtained with screen-printed graphite electrodes and the 1:2 PP2A:PVA ratio. Catechyl monophosphate (CMP), α-naphthyl phosphate (α-NP) and 4-methylumbelliferyl phosphate (4-MUP) have been used as phosphorylated substrates to monitor the protein phosphatase activity by electrochemical methods, the former providing the highest chronoamperometric currents at appropriate working potentials (+450 mV versus Ag/AgCl). Incubation with standard microcystin solutions has demonstrated the inhibition of the immobilised enzyme, proportional to the toxin concentration. The standard inhibition curve has provided a 50% inhibition coefficient (IC₅₀) of 83 μg L⁻¹, a limit of detection (LOD; 35% inhibition) of 37 μg L⁻¹, and 100% inhibition at about 1000 μg L⁻¹. Real samples of cyanobacterial blooms from the Tarn River (Midi-Pyrénées, France) have been analysed using the developed amperometric biosensor and the toxin contents have been compared to those obtained by a conventional colorimetric protein phosphatase inhibition (PPI) assay and high-performance liquid chromatography (HPLC). The results clearly justify the use of the developed amperometric biosensor as screening method for microcystin detection.     

Multi-detection method for five common microalgal toxins based on the use of microspheres coupled to a flow-cytometry system

Freshwater and brackish microalgal toxins, such as microcystins, cylindrospermopsins, paralytic toxins, anatoxins or other neurotoxins are produced during the overgrowth of certain phytoplankton and benthic cyanobacteria, which includes either prokaryotic or eukaryotic microalgae. Although, further studies are necessary to define the biological role of these toxins, at least some of them are known to be poisonous to humans and wildlife due to their occurrence in these aquatic systems. The World Health Organization (WHO) has established as provisional recommended limit 1 μg of microcystin-LR per liter of drinking water. In this work we present a microsphere-based multi-detection method for five classes of freshwater and brackish toxins: microcystin-LR (MC-LR), cylindrospermopsin (CYN), anatoxin-a (ANA-a), saxitoxin (STX) and domoic acid (DA). Five inhibition assays were developed using different binding proteins and microsphere classes coupled to a flow-cytometry Luminex system. Then, assays were combined in one method for the simultaneous detection of the toxins. The IC₅₀'s using this method were 1.9 ± 0.1 μg L⁻¹ MC-LR, 1.3 ± 0.1 μg L⁻¹ CYN, 61 ± 4 μg L⁻¹ ANA-a, 5.4 ± 0.4 μg L⁻¹ STX and 4.9 ± 0.9 μg L⁻¹ DA. Lyophilized cyanobacterial culture samples were extracted using a simple procedure and analyzed by the Luminex method and by UPLC–IT-TOF-MS. Similar quantification was obtained by both methods for all toxins except for ANA-a, whereby the estimated content was lower when using UPLC–IT-TOF-MS. Therefore, this newly developed multiplexed detection method provides a rapid, simple, semi-quantitative screening tool for the simultaneous detection of five environmentally important freshwater and brackish toxins, in buffer and cyanobacterial extracts.     

Generation and characterization of polyclonal antibodies against microcystins-Application to immunoassays and immunoaffinity sample preparation prior to analysis by liquid chromatography and UV detection

Polyclonal antibodies against microcystin-LR (MC-LR), a cyclic heptapeptide toxin, were generated in rabbits using MC-LR-BSA. An enzyme-linked immunosorbent assay (ELISA) was developed for the characterization of the antibodies and their potential use for analytical purposes. The concentration of MC-LR that inhibits 50% of antibody-antigen binding (IC₅₀) was 0.5 μg L⁻¹ for the indirect ELISA format and 0.9 μg L⁻¹ for the direct ELISA, using MC-LR-horseradish peroxidase conjugate. The limit of detection corresponding to IC₈₀ was found to be 0.06 μg L⁻¹, well below the Word Health Organization level for drinking water of 1 μg L⁻¹. The direct competitive ELISA was applied to water samples and was shown useful for screening purposes. The developed anti-microcystin antibodies were immobilized on solid supports for use in selective solid phase extraction (SPE) systems, prior to liquid chromatography (LC) quantification. An immunoaffinity cartridge (IAC), a Sepharose^®-based cartridge incorporating 2 mg of antibodies allowed the selective and quantitative recovery of a mixture of 0.2 μg of MCs showing potential use in sample preparation of real matrices. When applied to water and green algae samples, average recoveries from Sepharose^®-based cartridges were in the range of 86-113% for water samples and 85-92% for blue-green algae samples. Selectivity of the IAC clean-up was proven by comparison with non-specific solid phase extraction using octadecylsilica (ODS) sorbent. Results obtained using LC/UV after IAC clean-up agreed well with results obtained using liquid chromatography and mass spectrometry detection (LC/MS and LC/MS/MS) after SPE-C18 clean-up, allowing therefore to validate the resulting technique.     

A comprehensive immunoassay for the detection of microcystins in waters based on polyclonal antibodies

Microcystins (MCs) are a group of closely related toxic cyclic heptapeptides produced by common cyanobacteria (blue-green algae), and microcystin-leucine-arginine (MC-LR) is among the most frequent and most toxic microcystin congeners. In this study, a free amino group was introduced to MC-LR at its seventh amino acid residue with 2-mercaptoethylamine, and the product aminoethyl-MC-LR was coupled to bovine serum albumin (BSA) and horseradish peroxidise (HRP) by glutaraldehyde to be complete antigen (MC-LR-BSA) and labelled hapten (MC-LR-HRP), respectively. Polyclonal antibodies against MC-LR were generated by immunization with MC-LR-BSA. A direct competitive enzyme-linked immunosorbent assay (dc-ELISA) was established to detect the MCs in waters, which showed a good cross-reactivity with MC-LR, MC-RR, MC-YR, MC-LF, MC-LW and nodularin, and have a detection limit for MC-LR 0.12 μg L⁻¹, the 50% inhibition concentration (IC₅₀) for MC-LR was 0.63 ± 0.06 μg L⁻¹ and the quantitative detection range was from 0.17 to 2.32 μg L⁻¹, the analysis result of water samples showed good recovery and reliability. So the comprehensive and reliable dc-ELISA will well potentially suit for sensitive analysis for total MCs in drinking as well as resource water samples.     

A highly specific immunoassay for microcystin-LR detection based on a monoclonal antibody

Microcystins (MC) are cyanobacterial hepatotoxins responsible for animal-poisoning and human health incidents. Immunoassays provide a sensitive and fast means to detect these toxins, but cross-reactivity (CR) characteristic of different antibodies was variable. Here, we have produced and characterized a monoclonal antibody (Clone MC8C10) with highly specificity against the most frequent and most toxic variant of microcystins, MC-LR. MC8C10 is more specific against MC-LR among the reported antibodies before. The immunogen was synthesized from the modified MC-LR and bovine serum albumin (BSA). An indirect competitive enzyme-linked immunosorbent assay (ic-ELISA) with MC8C10 was established to detect the MCs in waters, which showed highly specificity with MC-LR, and have a detection limit for MC-LR 0.1 μg L⁻¹, the 50% inhibition concentration (IC₅₀) for MC-LR was 1.8 ± 0.1 μg L⁻¹ and the quantitative detection range was from 0.3 to 10 μg L⁻¹. The [4-arginine] microcystins and the nodularin-R showed lower cross-reactivates (CR < 10%), and other MCs such as MC-LF and MC-LW are not recognized (CR < 10⁻⁴). The analysis results of real water samples with ic-ELISA showed that all the coefficients of variation were less than 15%, and the recovery was (100.3 ± 5.9)%. So the highly specific ic-ELISA will commendably suit for sensitive analysis for MC-LR in surface water as well as drinking water.     

Determination of the steroid hormone levels in water samples by dispersive liquid-liquid microextraction with solidification of a floating organic drop followed by high-performance liquid chromatography

In this study, the steroid hormone levels in river and tap water samples were determined by using a novel dispersive liquid-liquid microextraction method based on the solidification of a floating organic drop (DLLME-SFO). Several parameters were optimized, including the type and volume of the extraction and dispersive solvents, extraction time, and salt effect. DLLME-SFO is a fast, cheap, and easy-to-use method for detecting trace levels of samples. Most importantly, this method uses less-toxic solvent. The correlation coefficient of the calibration curve was higher than 0.9991. The linear range was from 5 to 1000 μg L⁻¹. The spiked environmental water samples were analyzed using DLLME-SFO. The relative recoveries ranged from 87% to 116% for river water (which was spiked with 4 μg L⁻¹ for E1, 3 μg L⁻¹ for E2, 4 μg L⁻¹ for EE2 and 9 μg L⁻¹ for E3) and 89% to 102% for tap water (which was spiked with 6 μg L⁻¹ for E1, 5 μg L⁻¹ for E2, 6 μg L⁻¹ for EE2 and 10 μg L⁻¹ for E3). The detection limits of the method ranged from 0.8 to 2.7 μg L⁻¹ for spiked river water and 1.4 to 3.1 μg L⁻¹ for spiked tap water. The methods precision ranged from 8% to 14% for spiked river water and 7% to 14% for spiked tap water.     

Analysis of microcystins by capillary zone electrophoresis coupling with electrospray ionization mass spectrometry

In this paper, a rapid and effective method based on capillary zone electrophoresis (CZE) coupled with electrospray ionization mass spectrometry (ESI-MS) was established for the trace analysis of microcystin (MC) isomers in crude algae sample. The experimental conditions including the composition, acidity and concentration of buffer, separation voltage, injection time, and MS detection parameters were investigated in detail. A capillary separation system was as follows: a uncoated fused-silica capillary tube (50 μm i.d. × 90 cm), 40 mmol L⁻¹ ammonium acetate solution (pH 9.86) as running buffer, 25 kV as separation voltage, 20 kV × 3 s water first and 20 kV × 20 s for sample injection. Mass analysis was performed in ESI source, with sheath gas temperature 150 °C, sheath gas pressure 10 psi, and sheath gas flow 6 L min⁻¹. And sheath liquid was 7.5 mmol L⁻¹ acetic acid in 50% isopropanol-water (3 μL min⁻¹). Protonation and ammonium adduct molecular ions m/z 506.9 (MC-LR) and 532.0 (MC-YR) were used for the quantification of MCs. Under these conditions, two MCs were baseline separated within 9 min, the calibration curves were obtained in the range of 0.11-10.0 μg mL⁻¹ and 0.16-10.5 μg mL⁻¹ for MC-LR and MC-YR, respectively. Meanwhile, limits of detection were 0.05 and 0.08 μg mL⁻¹ for MC-LR and MC-YR, respectively. The recoveries for the two MCs were in the range of 95.8-108%. The developed approach had been successfully applied to the analysis of MCs in crude algae samples.     

Development of a highly sensitive inhibition immunoassay for microcystin-LR

The development of a rapid one-step antigen-immobilized inhibition ELISA for microcystin-LR is described. For microplate coating a microcystin-biotin conjugate was synthesized. Using the commercially available monoclonal antibody MC10E7 in our newly established assay, IC₅₀ values of 0.045 μg l⁻¹ have been achieved. The detection limit for microcystin-LR was 4 ng l⁻¹. Considering the guidelines proposed by the world health organization (WHO) for microcystin-LR in drinking water (1 μg l⁻¹) the sensitivity of our test is more than sufficient. The period of assay processing could successfully be shortened to about 3 h without any loss in sensitivity. The suitability of the newly developed assay was evaluated with microcystin-LR spiked environmental water samples. Recovery rates for microcystin-LR between 60 and 165% were obtained in the linear range of the test format. The antigen-immobilized test format provides a highly reproducible, easy, and fast to perform detection system for microcystin allowing an internal retrospective quality control of the assay.     

Direct colorimetric detection of copper(II) ions in sampling using diffusive gradients in thin-films

A novel binding phase was developed for use in diffusive gradients in thin-film (DGT) sampling for Cu(II) by employing methylthymol blue as a chelating and chromogenic agent. Methylthymol blue was adsorbed onto beads of Dowex 1 × 8 resin (200-400 mesh) and the resin beads were then immobilised onto an adhesive disc. Analysis of exposed binding discs by either UV-vis spectrophotometry or computer imaging densitometry provided robust quantification of adsorbed Cu(II) in the 0.2-1 μg cm⁻² range, allowing detection at μg L⁻¹ concentrations in the test solution (ca. 17 μg L⁻¹ for a 24 h deployment), and in good agreement with established DGT theory. The method was shown to be a potential replacement for binding phases based on Chelex 100 where a colorimetric response to a specific metal is desired.     

Enzyme sensor for the electrochemical detection of the marine toxin okadaic acid

An enzyme sensor for the electrochemical detection of the marine toxin okadaic acid (OA) has been developed. The strategy was based on the inhibition of immobilised protein phosphatase (PP2A) by this toxin and the electrochemical measurement of the enzyme activity by the use of appropriate enzyme substrates, electrochemically active after dephosphorylation by the enzyme. Colorimetric inhibition assays have demonstrated the PP2A from human red blood cells to be more sensitive and to provide a wider linear range than the one produced by genetic engineering. Catechyl monophosphate (CMP) and p-aminophenyl phosphate (p-APP) have been tested as enzyme substrates, the former providing higher electrochemical currents at convenient working potentials (+450 mV vs. Ag/AgCl). Biosensors with 19.1 and 5.0 U of immobilised enzyme have been applied to the OA detection. Whereas the 19.1-U biosensor has provided higher electrochemical currents and more reliable determinations, the 5.0-U one has attained a lower 50% inhibition coefficient (IC₅₀) value (22.19 in front of 154.84 μg L⁻¹) and a larger working range (2.69-171.87 in front of 42.97-171.87 μg L⁻¹). The analysis of toxicogenic dinoflagellate extracts with both biosensors and the comparison with the colorimetric assay and liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS) have demonstrated the applicability of the developed electrochemical devices as screening biotools for the assessment of the toxicity of a sample.     

Multiplex competitive microbead-based flow cytometric immunoassay using quantum dot fluorescent labels

In answer to the ever-increasing need to perform the simultaneous analysis of environmental hazards, microcarrier-based multiplex technologies show great promise. Further integration with biofunctionalized quantum dots (QDs) creates new opportunities to extend the capabilities of multicolor flow cytometry with their unique fluorescence properties. Here, we have developed a competitive microbead-based flow cytometric immunoassay using QDs fluorescent labels for simultaneous detection of two analytes, bringing the benefits of sensitive, rapid and easy-of-manipulation analytical tool for environmental contaminants. As model target compounds, the cyanobacterial toxin microcystin-LR and the polycyclic aromatic hydrocarbon compound benzo[a]pyrene were selected. The assay was carried out in two steps: the competitive immunological reaction of multiple targets using their exclusive sensing elements of QD/antibody detection probes and antigen-coated microsphere, and the subsequent flow cytometric analysis. The fluorescence of the QD-encoded microsphere was thus found to be inversely proportional to target analyte concentration. Under optimized conditions, the proposed assay performed well within 30 min for the identification and quantitative analysis of the two environmental contaminants. For microcystin-LR and benzo[a]pyrene, dose–response curves with IC₅₀ values of 5 μg L⁻¹ and 1.1 μg L⁻¹ and dynamic ranges of 0.52–30 μg L⁻¹ and 0.13–10 μg L⁻¹ were obtained, respectively. Recovery was 92.6–106.5% for 5 types of water samples like bottled water, tap water, surface water and seawater using only filtration as sample pretreatment.     

Determination of 4-ethylcatechol in wine by high-performance liquid chromatography-coulometric electrochemical array detection

A HPLC method using a coulometric electrode array detector (CEAD) to analyse 4-ethylcatechol in wine was established. The procedure does not require any sample preparation or analyte derivatisation and performs chromatographic separation in a short time. The assay method is linear up to 1520 μg L⁻¹ and precise (R.S.D. < 3%), with limits of detection and quantitation of 1.34 μg L⁻¹ and 2.2 μg L⁻¹, respectively. Recoveries in spiked wine samples ranged from 95% to 104% with a median value of 102% and matrix effects were not observed. The method was applied to the evaluation of the concentration of 4-EC in 250 commercial Italian wines. The red wines analysed had median, 75° percentile and maximum values of 37 μg L⁻¹, 89 μg L⁻¹ and 1610 μg L⁻¹, respectively. For Sangiovese-based wines the mean ratios of 4-EP and 4-EG to 4-EC were 3.7:1 and 0.7:1, respectively. The feasibility of a cheaper fluorimetric approach to 4-EC quantification was investigated.     

The use of a polymer inclusion membrane for separation and preconcentration of orthophosphate in flow analysis

A highly sensitive flow analysis system has been developed for the trace determination of reactive phosphate in natural waters, which uses a polymer inclusion membrane (PIM) with Aliquat 336 as the carrier for on-line analyte separation and preconcentration. The system operates under flow injection (FI) and continuous flow (CF) conditions. Under optimal FI conditions the system is characterised by a linear concentration range between 0.5 and 1000 μg L⁻¹ P, a sampling rate of 10 h⁻¹, a limit of detection of 0.5 μg L⁻¹ P and RSDs of 3.2% (n = 10, 100 μg L⁻¹) and 7.7% (n = 10, 10 μg L⁻¹). Under CF conditions with 10 min stop-flow time and sample solution flow rate of 1.32 mL min⁻¹ the flow system offers a limit of detection of 0.04 μg L⁻¹ P, a sampling rate of 5 h⁻¹ and an RSD of 3.4% (n = 5, 2.0 μg L⁻¹). Interference studies revealed that anions commonly found in natural waters did not interfere when in excess of at least one order of magnitude. The flow system, operating under CF conditions, was successfully applied to the analysis of natural water samples containing concentrations of phosphate in the low μg L⁻¹ P range, using the multipoint standard addition method.     

Analysis of phenylurea and propanil herbicides by solid-phase microextraction and liquid chromatography combined with post-column photochemically induced fluorimetry derivatization and fluorescence detection

This study examines the application of solid-phase microextraction coupled with high performance liquid chromatography combined with post-column photochemically induced fluorimetry derivatization and fluorescence detection (SPME-HPLC-PIF-FD) for the determination of four phenylurea herbicides (monolinuron, diuron, linuron and neburon) and propanil in groundwater. Direct immersion (DI) SPME was applied using a 60 μm polydimethylsiloxane/divinylbenzene (PDMS/DVB) fiber for the extraction of the pesticides from groundwater samples. An AQUASIL C₁₈ column (150 mm × 4.6 mm i.d., 5 μm) was used for separation and determination in HPLC. The method was evaluated with respect to the limits of detection (LODs) and the limits of quantification (LOQs) according to IUPAC. The limits of detection varied between 0.019 μg L⁻¹ and 0.034 μg L⁻¹. Limits of quantification ranged between 0.051 μg L⁻¹ and 0.088 μg L⁻¹. These values meet the recommended limits for individual pesticides in groundwater (0.1 μg L⁻¹) established by the EU. Recoveries ranged between 86% and 105% and relative standard deviation values between 2% and 8%.     

Feasibility of ultra-high performance liquid and gas chromatography coupled to mass spectrometry for accurate determination of primary and secondary phthalate metabolites in urine samples

Phthalates (PAEs) are ubiquitous toxic chemical compounds. During the last few years, some phthalate metabolites (MPAEs) have been proposed as appropriate biomarkers in human urine samples to determine PAE human intake and exposure. So, it is necessary to have fast, easy, robust and validated analytical methods to determine selected MPAEs in urine human samples. Two different instrumental methods based on gas (GC) and ultra-high performance liquid (UHPLC) chromatography coupled to mass spectrometry (MS) have been optimized, characterized and validated for the simultaneous determination of nine primary and secondary phthalate metabolites in urine samples. Both instrumental methods have similar sensitivity (detection limits ranged from 0.03 to 8.89 pg μL⁻¹ and from 0.06 to 0.49 pg μL⁻¹ in GC–MS and UHPLC–MS², respectively), precision (repeatability, expressed as relative standard deviation, which was lower than 8.4% in both systems, except for 5OH-MEHP in the case of GC–MS) and accuracy. But some advantages of the UHPLC–MS² method, such as more selectivity and lower time in the chromatographic runs (6.8 min vs. 28.5 min), have caused the UHPLC–MS² method to be chosen to analyze the twenty one human urine samples from the general Spanish population. Regarding these samples, MEP showed the highest median concentration (68.6 μg L⁻¹), followed by MiBP (23.3 μg L⁻¹), 5cx-MEPP (22.5 μg L⁻¹) and MBP (19.3 μg L⁻¹). MMP (6.99 μg L⁻¹), 5oxo-MEHP (6.15 μg L⁻¹), 5OH-MEHP (5.30 μg L⁻¹) and MEHP (4.40 μg L⁻¹) showed intermediate levels. Finally, the lowest levels were found for MBzP (2.55 μg L⁻¹). These data are within the same order of magnitude as those found in other similar populations.     

Development, validation and application of a SDME/GC-FID methodology for the multiresidue determination of organophosphate and pyrethroid pesticides in water

A single-drop microextraction (SDME) procedure was developed for the analysis of organophosphorus and pyrethroid pesticides in water by gas chromatography (GC) with flame ionization detection (GC-FID). The significant parameters that affect SDME performance, such as the selection of microextraction solvent, solvent volume, extraction time, and stirring rate, were studied and optimized using a tool screening factorial design. The limits of detection (LODs) in water for the four investigated compounds were between 0.3 and 3.0 μg L⁻¹, with relative standard deviations ranging from 7.7 to 18.8%. Linear response data were obtained in the concentration range of 0.9-6.0 μg L⁻¹ (λ-cyhalothrin), 3.0-60.0 μg L⁻¹ (methyl parathion), 9.0-60.0 μg L⁻¹ (ethion), and 9.0-30.0 μg L⁻¹ (permethrin), with correlation coefficients ranging from 0.9337 to 0.9977. The relative recoveries for the spiked water ranged from 73.0 to 104%. Environmental water samples (n = 26) were successfully analyzed using the proposed method and methyl parathion presented concentration up to 2.74 μg L⁻¹. The SDME method, coupled with GC-FID analysis, provided good precision, accuracy, and reproducibility over a wide linear range. Other highlights of the method include its ease of use and its requirement of only small volumes of both organic solvent and sample.     

Development and characterization of a new polyampholyte-surfactant complex applied to the solid phase extraction of bisphenol-A

This paper presents a material that has both hydrophilic and hydrophobic domains, obtained by combination of a polyampholyte with a surfactant. This material was fully characterized by different spectroscopic techniques and microscopy.Bisphenol-A (BPA) was chosen as a model molecule to study the interaction with compounds of intermediate polarity. We explored the kinetics and equilibrium of BPA on the surface of the polyampholyte-surfactant complex and found a significantly high loading capacity (2.02 mmol g⁻¹) and complete binding from solutions at concentration levels below 100 μmol L⁻¹.The complex was encapsulated in agarose gel to be used as solid phase for extraction of BPA from food simulants in contact with polycarbonate bottles under different treatments. Bisphenol was preconcentrated, extracted and analysed by liquid chromatography with an amperometric detector. The instrumental detection limit of the technique was 10 μg L⁻¹, which was lowered to 0.14 μg L⁻¹ by the preconcentration step. The BPA released from baby bottles was 2.1 ng cm⁻² (σ_n − 1: 0.1) in the first use with distilled water.     

High-sensitivity determination of lead and cadmium based on the Nafion-graphene composite film

Graphene nanosheets, dispersed in Nafion (Nafion-G) solution, were used in combination with in situ plated bismuth film electrode for fabricating the enhanced electrochemical sensing platform to determine the lead (Pb²⁺) and cadmium (Cd²⁺) by differential pulse anodic stripping voltammetry (DPASV). The electrochemical properties of the composite film modified glassy carbon electrode were investigated. It is found that the prepared Nafion-G composite film not only exhibited improved sensitivity for the metal ion detections, but also alleviated the interferences due to the synergistic effect of graphene nanosheets and Nafion. The linear calibration curves ranged from 0.5 μg L⁻¹ to 50 μg L⁻¹ for Pb²⁺ and 1.5 μg L⁻¹ to 30 μg L⁻¹ for Cd²⁺, respectively. The detection limits (S/N = 3) were estimated to be around 0.02 μg L⁻¹ for Pb²⁺ and Cd²⁺. The practical application of the proposed method was verified in the water sample determination.