Synthesis of a random copolymer and its compatibility for thermotropic liquid crystalline polymer/poly(ether ether ketone) blends

A random copolymer (RCP) containing poly(ether ether ketone) (PEEK) and thermotropic liquid crystalline polymer (TLCP) segments was synthesized. Its chemical structure and liquid crystalline properties were characterized by FT‐IR, differential scanning calorimetry (DSC) and polar light microscopy (PLM) respectively. A single glass transition temperature (T_g) at 134.0°C, a melting temperature (T_m) at 282.0°C and a temperature of ignition (T_i) at 331.3°C can be observed. Blends of PEEK and TLCP with and without RCP as compatibilizer were prepared by extrusion and the effect of RCP on the thermal properties, dynamic mechanical properties, morphology and static tensile mechanical properties of blends was investigated by means of DSC, dynamic mechanical analysis (DMA), scanning electron microscopy (SEM), etc. Dynamic mechanical measurements indicated that there appeared to be only a single tan δ peak resulting from the glass transition of the PEEK‐rich phase and the T_g value shifted towards higher temperature due to the presence of compatibilizer, as suggested partial compatibility. Morphological investigations showed that the addition of RCP to binary blends reduced the dispersed phase size and improved the interfacial adhesion between the two phases. The ternary compatibilized blends showed enhanced tensile modulus compared to their binary blends without RCP. The strain at break decreased for the ternary blends due to embrittlement of the matrix by the incorporation of some RCP to the matrix phase. Copyright © 2007 John Wiley & Sons, Ltd.     

Miscibility and compatibilization of poly(trimethylene terephthalate)/acrylonitrile-butadiene-styrene blends

Poly(trimethylene terephthalate)/acrylonitrile-butadiene-styrene (PTT/ABS) blends were prepared by melt processing with and without epoxy or styrene-butadiene-maleic anhydride copolymer (SBM) as a reactive compatibilizer. The miscibility and compatibilization of the PTT/ABS blends were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), capillary rheometer and scanning electron microscopy (SEM). The existence of two separate composition-dependent glass transition temperatures (T_gs) indicates that PTT is partially miscible with ABS over the entire composition range. In the presence of the compatibilizer, both the cold crystallization and glass transition temperatures of the PTT phase shifted to higher temperatures, indicating their compatibilization effects on the blends.The PTT/ABS blends exhibited typical pseudoplastic flow behavior. The rheological behavior of the epoxy compatibilized PTT/ABS blends showed an epoxy content-dependence. In contrast, when the SBM content was increased from 1 wt% to 5 wt%, the shear viscosities of the PTT/ABS blends increased and exhibited much clearer shear thinning behavior at higher shear rates. The SEM micrographs of the epoxy or SBM compatibilized PTT/ABS blends showed a finer morphology and better adhesion between the phases.     

Thermal degradation behavior of radiation synthesized polydiallyldimethylammonium chloride

Thermogravimetric analysis (TGA) and differential scanning calorimetric (DSC) studies were carried out on gamma radiation synthesized polydiallyldimethylammonium chloride (PDADMAC). The polymer was found to undergo thermal degradation in two stages. The first stage showed a weight loss of 33% and the second stage showed a weight loss of 67%. The DSC thermogram shows two endothermic peaks corresponding to the two stages in the TG thermogram and the experimental enthalpy change associated with the first and second stages were 650 J g⁻¹ and 129.5 J g⁻¹, respectively. The nth-order kinetic parameters (order of the reaction, activation energy and the pre-exponential factor) were determined from a single dynamic DSC or thermogravimetric (TG) thermogram by the method of least square. Theoretical TG/differential thermogravimetric (DTG) and DSC thermograms derived from the calculated kinetic parameters were in good agreement with the experimental ones at the heating rate employed. However, the kinetic parameters determined using TG and DSC were different. This leads to the conclusion that the degradation mechanism could be complicated and may consists of a number of parallel or consecutive reactions. The glass transition temperature (T_g) of the polymer was found to be around 150 °C depending on the test method employed.     

Nonisothermal crystallization kinetics and melting behavior of bimodal medium density polyethylene/low density polyethylene blends

Nonisothermal crystallization kinetics and melting behavior of bimodal-medium-density- polyethylene (BMDPE) and the blends of BMDPE/LDPE were studied using differential scanning calorimetry (DSC) at various scanning rates. The Avrami analysis modified by Jeziorny and a method developed by Mo were employed to describe the nonisothermal crystallization process of BMDPE. The BMDPE DSC data were analyzed by the theory of Ozawa. Kinetic parameters such as the Avrami exponent (n), the kinetic crystallization rate constant (Z_c), the peak temperatures (T_p) and the half-time of crystallization (t_1/2) etc. were determined at various scanning rates. The appearance of double melting peaks and the double crystallization peaks in the heating and cooling DSC curves of BMDPE/LDPE blends indicated that the BMDPE and LDPE could crystallize respectively.     

Thermal stability and viscoelastic properties of MF/PVAc hybrid resins on the adhesion for engineered flooring in under heating system; ONDOL

The thermal properties of blends of melamine-formaldehyde (MF) resin and poly(vinyl acetate) (PVAc) for engineered flooring used on the Korean traditional ONDOL house floor heating system were investigated by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA). The viscoelastic properties of the blends were also studied. Because MF resin is a thermosetting adhesive, the effect of MF rein was shown across all thermal behaviors. The addition of PVAc reduced the curing temperature. The TGA results showed that the DTG_max temperature and thermal stability of the blends increased with increasing PVAc content. The blends were examined in non-isothermal DSC experiments at a heating rate of 10 °C/min. There was an exothermic peak in all the heating scanning curves, with each blend displaying a single curing peak temperature (T_p), intermediate between those of the two pure components and varying with the blend composition. The DMTA thermogram of MF resin showed that the storage modulus (E′) increased as the temperature was further increased as a result of the cross-linking induced by the curing reaction of the resin. E′ of MF resin increased both as a function of increasing temperature and with increasing heating rate.     

Effect of PEG on the crystallization of PPDO/PEG blends

A new biodegradable polymer system, poly(p-dioxanone) (PPDO)/poly(ethylene glycol) (PEG) blend was prepared by a solvent casting method using chloroform as a co-solvent. The PPDO/PEG blends have different weight ratios of 95/5, 90/10, 80/20 and 70/30. Crystallization of homopolymers and blends were investigated by differential scanning calorimetry (DSC) and wide-angle X-ray diffraction (WAXD). When 5% of PEG was blended, the crystallization exothermal peaks (T_c) of PPDO increased sharply and the crystallization exothermal peaks (T_c) of PEG decreased slightly compared with the homopolymers. The crystallization rates of both components increased, and caused greater relative crystallization degree (X_t%). But when the content of PEG was more than 5%, the crystalline behaviors of blends had no more significant changes accordingly. The melting points of each sample varied little over the entire composition range in this study. The nonisothermal crystallization of PPDO homopolymer and blend (PPDO/PEG = 70/30) were also studied by DSC. The crystallization began at a higher temperature when the cooling rates were slower. The nonisothermal crystallization kinetics of blends was analyzed by Ozawa equation. The results showed that the Ozawa equation failed to describe the whole crystallization of the blend, but Mo equation could depict the nonisothermal crystallization perfectly.     

Dynamic mechanical and thermal properties of physically compatibilized natural rubber/poly(methyl methacrylate) blends by the addition of natural rubber‐graft‐ poly(methyl methacrylate)

The dynamic mechanical and thermal properties of natural rubber/poly (methyl methacrylate) blends (NR/PMMA) with and without the addition of graft copolymer (NR‐g‐PMMA) have been investigated. Dynamic mechanical spectroscopy is used to examine the effect of compatibilizer loading on storage modulus (E′), loss modulus (E″) and loss tangent (tan δ) at different temperatures and at different frequencies. The morphology of the blends indicates that the size of the dispersed phase decreased by the addition of a few percent of the graft copolymer followed by a leveling off at higher concentrations. This is an indication of interfacial saturation. Attempts have been made to correlate morphology with dynamic mechanical properties. Various models have been used to fit the experimental viscoelastic results. Differential scanning calorimetry has been used to analyze the glass‐transition temperatures of the blends. The thermal stability of the blends has been analyzed by thermogravimetry. Compatibilized blends are found to be more thermally stable than uncompatibilized blends. Finally the miscibility and mechanical properties of the blends annealed above T_g are evaluated. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 525–536, 2000     

Thermal behaviour of styrene butadiene rubber/poly(ethylene-co-vinyl acetate) blends

The thermal behaviour of styrene butadiene rubber (SBR)/poly (ethylene-co-vinyl acetate) (EVA) blends was studied by using thermogravimetry (TG) and differential scanning calorimetry (DSC). The effects of blend ratio, cross-linking systems and compatibilization on the thermal stability and phase transition of the blends were analyzed. It was found that the mass loss of the blends at any temperature was lower than that of the components, highlighting the advantage of blending SBR and EVA. The addition of compatibilizer was also found to improve the thermal stability. DSC studies indicated the thermodynamic immiscibility of SBR/EVA system even in the presence of the compatibilizer. This is evident from the presence of two different glass transition temperatures, corresponding to SBR and EVA phases in both compatibilized and uncompatibilized blends.     

Thermal properties of microcrystalline cellulose-filled PET–PTT blend polymer composites

Polymer composite materials were prepared from poly(ethylene terephthalate)–poly(trimethylene terephthalate) blends as the matrix and different microcrystalline cellulose (MCC) filler levels (0–40 wt%) using melt compounding followed by compression molding. The composites were analyzed using dynamic mechanical thermal analysis (DMTA), differential scanning calorimetry (DSC) and thermogravimetric analysis (TG). The DSC results indicated that there is no consistent or significant influence of the MCC addition on the glass transition (T _g), melting (T _m), and crystallization temperature of the composites. With increasing MCC content, dynamic mechanical properties improved because of the reinforcing effect of the MCC. The tan δ peak values from the DMTA were not significantly changed as the MCC content increased. TG indicated that the onset temperature of rapid thermal degradation decreased with increasing MCC content. It was also found that the thermal stability of the composites slightly decreased as the MCC content increased.     

Experimental study of flow-induced crystallization in the blends of isotactic polypropylene and poly(ethylene-co-octene)

The crystallization behavior of the blends of isotactic polypropylene (iPP) and poly(ethylene-co-octene) (PEOc) under quiescent condition and shear flow were studied by differential scanning calorimetry (DSC) and rheology, respectively. The DSC curves of the iPP phase in the blends showed similar crystallization exothermic peaks to that of pure iPP itself, indicating that the addition of PEOc up to a percentage of 30 in weight almost had no influence on the crystallization behavior of iPP at quiescent condition. The rheological results of isothermal flow-induced crystallization (FIC) of iPP in the blends showed that the crystallization kinetics of iPP was enhanced with the increase of shear rate, similar to that of pure iPP, but the presence of PEOc enhanced the effect of shear on the crystallization kinetics of iPP significantly in the cases of shear rates larger than 0.2 s⁻¹, which was due to that PEOc played an important role to promote the nucleation of iPP. The rheological results also implied that the characteristic relaxation times of blends were longer than that of pure iPP during the FIC process, indicating a different relaxation mechanism which might be related to the occurrence of interface relaxation and chain relaxation of the PEOc phase in the blends.     

Characterization of Rubber Epoxy Blends by Thermal Analysis

Differential scanning calorimetry (DSC), thermogravimetric analysis (TG) and dynamic mechanical analysis (DMA) of the blends ofepoxy cresol novolac (ECN) resin toughened with liquid carboxy terminated butadiene-co-acrylonitrile (CTBN) rubber have been carried out. Exothermal heat of reaction (ΔH) due to crosslinking of the resin in presence of diaminodiphenyl methane(DDM, as amine hardener) showed a decreasing trend with increasing rubber concentration. Enhancements of thermal stability as well as lower percentage mass loss of the epoxy-rubber blends with increasing rubber concentration have been observed in TG. Dynamic mechanical properties reflected a monotonic decrease in the storage modulus (E′) with increasing rubber content in the blends. The loss modulus (E″) and the loss tangent(tanδ) values, however, showed an increasing trend with rise of the temperature up to a maximum (peak) followed by a gradual fall in both cases. Addition of 10 mass% of CTBN resulted maximum E″ and tanδ. This revised version was published online in July 2006 with corrections to the Cover Date.     

Thermal properties of single walled carbon nanotubes composites of polyamide 6/poly(methyl methacrylate) blend system

The nanocomposites of polyamide 6 (PA6)/poly(methyl methacrylate) (PMMA)/non-functionalized and functionalized [carboxylic acid (COOH) and hydroxyl (OH)] single wall carbon nanotubes (SWCNTs) were prepared in mass ratios of 79.5/19.5/1, 49.5/49.5/1, and 19.5/79.5/1 by melt–mixing method at 230 °C. The PA6/PMMA blends with mass ratios of 80/20, 50/50, and 20/80 served as references. The Fourier transform infrared analyses of nanocomposites showed the formation of hydrogen bond interactions among PA6, PMMA, and OH and COOH functional groups of SWCNTs. The nanocomposites and blends had higher thermal stability with respect to the PMMA. The differential scanning calorimeter (DSC) curves showed that the nanocomposites and blends exhibited two T _g values at around 51 and 126 °C for PA6 and PMMA, respectively. About 20 °C early crystallization was observed in nanocomposites compared to the blends. The dynamic mechanical analysis (DMA) results suggested that among all the compositions of blends and nanocomposites, storage modulus (E′) was higher for PMMA-rich blends and nanocomposites. At 25 °C, the E′ values were higher for blends and nanocomposites compared to the neat PA6. The tan δ curves indicated that the more heterogeneity of the hybrid nature resulted in PA6/PMMA/SWCNTs-OH or SWCNTs-COOH with 79.5/19.5/1 mass ratio nanocomposites compared to the PA6/PMMA with 80/20 mass ratio blend. The higher T _g values of PA6 and PMMA were observed in DMA studies compared to the DSC studies for PA6 and PMMA as neat and in blends and nanocomposites. The significant improvements in crystallization of nanocomposites were considered resulting from achieving better compatibility among the polymer components and carbon nanotubes.     

Influence of hygrothermally degraded polyester-urethane on physical and mechanical properties of chloroprene rubber

The influence of hygrothermally-degraded polyester urethane (HD-PUR) waste on chloroprene rubber (CR) has been studied giving special attention to curing behaviour, mechanical properties and dynamic mechanical behaviour. The presence of primary and secondary amines in HD-PUR, did not increase the cure rate of CR. The mechanical properties of chloroprene vulcanizates were improved upon HD-PUR addition. The strain-induced crystallisation of CR did not show any deviation upon the addition of HD-PUR. Crosslink densities calculated from swelling studies, stress-strain behaviour, and modulus measurements are found to increase upon HD-PUR addition and showed similar trend. The glass transition temperature (T_g) did not show any significant change, with the addition of HD-PUR. Scanning electron microscopic studies have been done in order to have an insight into fracture behaviour of the samples and to analyse the microstructure of the blends.     

UV-curing behavior and adhesion performance of polymeric photoinitiators blended with hydrogenated rosin epoxy methacrylate for UV-crosslinkable acrylic pressure sensitive adhesives

UV-crosslinkable polyacrylates were synthesized for use as pressure sensitive adhesives (PSAs). These polyacrylates acted as polymeric photoinitiators due to the benzophenone incorporated into their backbones. Hydrogenated rosin epoxy methacrylate (HREM; based on hydrogenated rosin and glycidyl methacrylate) was also synthesized as a tackifier, and blended at different levels with the synthesized, UV-crosslinkable polyacrylates for use as PSAs. The effect of the new tackifier, HREM, on the properties of the UV-crosslinkable PSAs was examined in comparison with the properties exhibited by PSA/hydrogenated rosin blends. The characteristics of these PSA/tackifier blends were examined by Fourier-transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC) and an advanced rheometric expansion system (ARES). In addition, the adhesion performance of the PSA blends was investigated using probe tack tests. DSC and ARES revealed all the PSA blends with HREM or hydrogenated rosin to be miscible at the molecular level. The glass transition temperature (T_g) of HREM was −25.6 °C, which is lower than that of other commercially available rosin tackifiers. FTIR revealed changes in the relative concentration of benzophenone groups in the PSAs at 1580 cm⁻¹, which demonstrated that the crosslinking efficiency is proportional to the benzophenone content and UV dose, but decreases with increasing hydrogenated rosin content. However, the reduced crosslinking reaction efficiency was improved in the PSA/HREM blends due to the low T_g of HREM which only slightly increased the T_g of the PSA blends. Moreover, the relative initial decrease in the probe tack of the PSA/HREM blends was lower than that of the PSA/hydrogenated rosin blends after UV irradiation.     

Thermal properties of compatibilized and filled natural rubber/acrylonitrile butadiene rubber blends

The thermal behaviour of natural rubber/acrylonitrile butadiene rubber (NR/NBR) was studied using thermogravimetry (TG) and differential scanning calorimetry (DSC) in terms of blend ratio, crosslinking systems, fillers and compatibilizer (neoprene) were analyzed. The presence of NBR markedly increases the thermal stability of their blends and it lies in between NR and NBR. DSC studies revealed the thermodynamic immiscibility of the NR/NBR blends by the presence of two distinct glass transition temperatures and the immiscibility was prominent even in the presence of a compatibilizer.     

Influence of chain extension on the compatibilization and properties of recycled poly(ethylene terephthalate)/linear low density polyethylene blends

Polymeric methylene diphenyl diisocyanate (PMDI) was added as chain extender to a blend of recycled poly(ethylene terephthalate) (R-PET) and linear low density polyethylene (LLDPE) with compatibilizer of maleic anhydride-grafted poly(styrene-ethylene/butadiene-styrene) (SEBS-g-MA). Hydroxyl end groups of PET can react with both isocyanate groups of PMDI and maleic anhydride groups of SEBS-g-MA, which are competing reactions during reactive extrusion. The compatibility and properties of the blends with various contents of PMDI were systemically evaluated and investigated. WAXD results and SEM observations indicated that chain extension inhibits the reaction between PET and SEBS-g-MA. As the PMDI content increased, the morphology of dispersed phase changed from droplet dispersion to rodlike shape and then to an irregular structure. The DSC results showed that the crystallinity of PET decreased in the presence of PMDI, and the glass transition temperature (T_g) of PET increased with addition of 0-0.7 w% PMDI. The impact strength of the blend with 1.1 w% PMDI increased by 120% with respect to the blend without PMDI, accompanied by only an 8% tensile strength decrease. It was demonstrated that the chain extension of PET with PMDI in R-PET/LLDPE/SEBS-g-MA blends not only decreased the compatibilization effect of SEBS-g-MA but also hindered the crystallization of PET.     

Characterization and properties of polyethylene blends I. Linear low-density polyethylene with high-density polyethylene

A blend system of linear low-density polyethylene (LLDPE) (ethylene butene-1 copolymer) with high-density (linear) polyethylene (HDPE) is investigated by differential scanning calorimetry (DSC), wide-angle x-ray diffraction (WAXD), small-angle x-ray scattering (SAXS), Raman longitudinal-acoustic-mode spectroscopy (LAM), and light scattering (LS). For slowly cooled or quenched samples, one single endotherm is evident in the DSC curve which depends on the composition. No separate peaks are observed in the WAXD, SAXS, Raman-LAM, and LS studies on the LLDPE/HDPE blends. This observation along with the fact that no peak broadening is observed suggests that these peaks are associated with the presence of a single component. In no case did we see double peaks or a broadened peak that might be associated with two closely spaced unresolved peaks. This suggests that segregation has not taken place at the structural levels of crystalline, lamellar, and spherulitic textures. A single-step drop in the scattered intensity (I_Hv) as a function of temperature is seen in the LS studies. It is therefore concluded that cocrystallization between the LLDPE and HDPE components occurs. The mechanical and optical α, β, and γ relaxations of these blends are explored by dynamic birefringence. The 50/50 blend displays the intermediate relaxation behavior between those of the components in all α, β, and γ regions. This observation is reminiscent of the characteristic of the typical miscible blends.     

Liquid crystalline properties of new unsymmetrical compounds with benzothiazole core detected by TG/DSC-POM-XRD

Thermal properties of two azomethine liquid crystals with a benzothiazole core were synthesized and investigated by applied Mettler-Toledo AG equipment (TG/DSC). Azomethines with benzothiazole core was obtained by nucleophilic addition of benzothiazole-2-carboxaldehyde in N,N-dimethylacetamide (DMA) solution with 4-(heptadecafluoroctyl)aniline (BTA1) or 4-hexadecylaniline (BTA2). The differential scanning calorimetry (DSC) was employed to evaluate their phase transitional behavior. Variable heating and cooling rates were used to study liquid crystalline properties of azomethines with benzothiazole core. Compound BTA1 exhibited liquid crystalline properties, while BTA2 is non-mesogenic. Three or four endothermic DSC peaks were observed for both compounds during heating process with the rate 0.5?°C/min. The mesophase was identified and confirmed by XRD study and polarized optical microscopy (POM) too. The thermal stability was determined by thermogravimetric analysis (TG). The temperatures of 5% mass loss (T _5%) of BTA1 and BTA2 range from 212 to 317?°C in nitrogen.     

相容剂对PP/POE共混体系脆韧转变行为的影响

采用熔融挤出法制备了不同相容剂含量的PP/POE共混体系,测试了不同体系的脆韧转变温度、热性能和力学性能.结果表明,乙烯-丙烯多嵌段共聚物相容剂的加入降低了PP/POE共混物的脆韧转变温度,提高了共混物的韧性.AFM和STEM照片显示相容剂的加入减小了橡胶分散相的临界粒子间距,PP和POE在两相界面结合处相互扩散或渗透,实现了POE弹性体在PP树脂中合适的尺度分布以及良好的形态分散.当相容剂含量达到10％时,POE分散相尺寸细小均匀,分散相粒子粒径为0.54μm,粒子间距为0.1 μm,PP结晶链段更多地插入到弹性体内部,弹性体POE分散相形成明显的“硬核-软壳”结构.DSC曲线中结晶峰和熔融峰的变化说明适量的相容剂对于材料结晶度的提高具有一定的促进作用.力学性能测试结果可以看出相容剂的加入在提高材料韧性,降低其脆韧转变温度的同时也保持了材料的刚性性能.     

Thermal properties and kinetics of new-generation posterior bulk fill composite cured light-emitting diodes

In this study, the thermal behavior in terms of glass transition (T _g), degradation, and thermal stability of four commercial new-generation posterior bulk fill composites (Surefill SDR, Dentsply; Quixfill, Dentsply; Xtrabase, Voco; and Xtrafill, Voco) activated by light-emitting diodes (LEDs) was analyzed by thermogravimetric analysis (TG), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). The activation energies (E _a) for the decomposition of the dental resins were calculated based on the Kissinger and Doyle kinetic models from the peaks of the endothermic curves obtained when the specimens were heated at four different temperatures (5, 10, 15, and 20 °C min^?1) during DSC. The results show that the Xtrabase composite displayed the highest T _g (120 °C at a 5 °C min^?1 heating rate) and E _a (157.64 kJ mol^?1) values associated with thermal degradation from the main chain of the polymer.