Studies of some mechanical and optical properties of: (70 − x)TeO2 + 15B2O3 + 15P2O5 + xLi2O glasses

Specimens of the glassy system: (70 − x)TeO₂ + 15B₂O₃ + 15P₂O₅ + xLi₂O, where x = 5, 10, 15, 20, 25 and 30 mol% were prepared by the melt-quenching. An ultrasonic pulse-echo technique was employed, at 5 MHz, for measuring: the ultrasonic attenuation, longitudinal and shear wave velocities, elastic moduli, Poisson ratio, Debye temperature and hardness of the present glasses. It is found that the gradual replacement of TeO₂ by Li₂O in the glass matrix up to 30 mol% leads to decrease the average crosslink density and rigidity of prepared samples which affects the properties, i.e., the hardness, ultrasonic wave velocities and elastic moduli are decreased, while the Poisson ratio and the ultrasonic attenuation are increased. Also, optical absorption spectra were recorded in the range, 200-800 nm for these glasses. The obtained results showed that a gradual shift in the fundamental absorption edge toward longer wavelengths occurred. Values of both of the optical energy gap, E_opt, and width tails, ΔE, are determined. It is observed that E_opt is decreased and ΔE increased with the increase of Li₂O in the glass matrix up to 30 mol%. The compositional dependences of the above properties are discussed and correlated to the structure of tested glasses.     

Crystallization of monoclinic WO3 in tungstate fluorophosphate glasses

Tungstate fluorophosphate glass compositions with high WO₃ concentration were prepared in the ternary system (80−0.8x)NaPO₃-(20−0.2x)BaF₂-xWO₃ with x = 40,50 and 60 mol%. Transparency decreases as WO₃ concentration increases but can be improved by addition of oxidizing systems such as CeO₂ or Sb₂O₃/NaNO₃. Characterizations by thermal analysis (DSC) point out that an increase in the amount of WO₃ results in a higher glass transition temperature. In addition, such compositions are very stable against devitrification since samples containing 40% and 50% of WO₃ donot even exhibit the expected crystallization event. In these samples, the stability against crystallization decreases with the WO₃ content and vitreous sample containing 60% of WO₃ exhibits an endothermic event around 620 °C due to crystallization of monoclinic WO₃ phase. In these glasses, it was shown that the nucleation stage can be induced by thermal-treatment when external nucleating agents such as Ti or Sb are used. Finally, gold-doped samples exhibit a higher crystallization tendency and monoclinic WO₃ phase can be grown in such glasses.     

Thermal and some physical properties of glasses in the La2O3−CaO−B2O3 ternary system

Glasses in the La₂O₃−CaO−B₂O₃ ternary system were studied. The glass forming range as determined by the appearance of the annealed cast was found to match previously published findings. Clear glasses were formed in the composition range of 5.7−19.1 mol% La₂O₃ with constant B₂O₃ content of 71.4 mol%, and in glasses of constant La₂O₃:CaO ratio of 1:4 with B₂O₃ content in the range of 71.4-55.0 mol%. The non-linear optical crystalline phase La₂Ca₂B₁₀O₁₉ was crystallized from the clear glasses after heat treatments, as determined by powder XRD. Two types of the LaBO₃ crystalline phases were detected in the partially and the fully crystallized glass compositions outside the glass forming range. Data are reported for the glass transition temperature (T_g), dilatometric softening point (T_d), linear coefficient of expansion (α), onset crystallization temperature (T_x), exothermal peak temperature (T_P), density (ρ) and index of refraction (n_D) in the clear glasses.     

Study of CaO-WO3-P2O5 glass system by dielectric properties, IR spectra and differential thermal analysis

Dielectric constant ε^′, loss tanδ and ac conductivity σ_ac of 40CaO-xWO₃-(60−x)P₂O₅ (with 0?x?15) glasses are studied over a range of frequencies and temperature. The dielectric breakdown strength of these glasses is also determined at room temperature. The values of dielectric parameters, viz., ε^′, tanδ and σ_ac of CaO-P₂O₅ glasses are found to decrease with the introduction of WO₃ up to 3 mol% and increase with further increase in the concentration of WO₃; the probable reasons for such an increase are identified and explained with the aid of IR spectra and differential thermal analysis of these glasses. The variation of tanδ with temperature at different frequencies of CaO-P₂O₅ glasses has exhibited dielectric relaxation effects with decreasing relaxation intensity with increase in the concentration of WO₃ from 0 to 3 mol%; such relaxation effects seem to have been absent in glasses containing WO₃ beyond 3 mol%. The relaxation phenomenon has been analysed by a pseudo-Cole-Cole plot method and the possible mechanism responsible for such relaxation effects has been suggested.     

Semiconducting TiO2SiO2 glasses (II): Optical properties

The refractive index, optical absorption coefficient α and the thermomodulated absorption dα/dT have been measured on 70% TiO₂?30% SiO₂ glasses with up to 8% Ti³⁺. The direct absorption data show intense ligand field absorption at photon energies hν = 1.9 and 3.0 eV, arising from Ti³⁺ in a distorted octahedral environment. In the bandgap region at 3.5 eV α obey αhν ～ (hν ? E_g)²; it is qualitatively different from the bandgap absorption in crystalline TiO₂. The da/dT spectra show peaks in the bandgap region and at 1.1 eV in the near IR. This last peak is attributed to absorption by small polarons, and its line shape is compared with theoretical predictions.     

RDF analysis, positron annihilation and Raman spectroscopy of xTiO2-(60 − x)SiO2-40Na2O non-linear optical glasses: III. Non-bridging oxygen bonds tracing and structure analysis

xTiO₂-(60 − x)SiO₂-40Na₂O glasses have proven an interesting linear and non-linear optical properties [M. Abdel-Baki, F. Abdel Wahab, F. El-Diasty, Mater. Chem. Phys. 96 (2006) 201]. The investigated glasses show one order of magnitude enhancement for the second-order index of refraction and third-order optical susceptibility over some TiO₂ silicate glasses. In this work, we continue studying these glasses using three different techniques to analyze the glass structures seeking to provide a deep insight for the relation between structure, compositions and the optical characteristics of these glasses. Radial Distribution Function analysis (RDF) combined Raman spectroscopy are used to study these glasses. Positron annihilation lifetime spectroscopy and Doppler broadening measurements are carried out to investigate the change in the glass structure as the incorporation of TiO₂ concentration into glass. The origin of the non-bridging oxygen (NBO) bonds has been traced to correlate their existence with the measured non-linear optical properties of the investigated glasses.     

Remark on the optical gap in ZnO-Bi2O3-TeO2 glasses

Four ZnO-Bi₂O₃-TeO₂ glasses were prepared from high purity (4N5) oxides. From measurements of the optical transmission on very thin bulk samples the optical gap was determined at around 3.55 eV for the glasses studied. The temperature dependence of the optical gap was also determined from the room temperature close up to 500 K. Preliminary Raman scattering measurements indicate that with a decrease in TeO₂ content, TeO₄ trigonal bipyramid transformation proceeds into TeO₃ trigonal pyramids.     

Spectroscopic properties of Er-doped Na2O-Sb2O3-B2O3-SiO2 glasses

Spectroscopic properties of Er³⁺-doped Na₂O-Sb₂O₃-B₂O₃-SiO₂ glasses have been investigated for developing 1.5-μm broadband fiber amplifiers. An intense 1.5-μm near infrared emission with a broad full width at half maximum (FWHM) of 88 nm has been obtained for Er³⁺-doped 5Na₂O-20Sb₂O₃-35B₂O₃-40SiO₂ glass upon excitation with a 980 nm laser diode. The obtained emission cross-section of the ⁴I_13/2 → ⁴I_15/2 transition and the lifetime of the ⁴I_13/2 level of Er³⁺ ions are 6.8 × 10⁻²¹ cm² and 0.36 ms, respectively. It is noted that the product of the emission cross-section and the FWHM of the glass, σ_e × FWHM, is as great as 598.4 × 10⁻²¹ cm² nm, which is comparable or higher than that of Er³⁺-doped bismuth-based and tellurite-based glasses. These special optical properties encourage in identifying them as important materials for potential applications in high performance optics and optical communication networks.     

Thermal, chemical, optical properties and structure of Er-doped and Er/Yb-codoped P2O5-Al2O3-ZnO glasses

This study was explored in series of the optical, thermal, and structure properties based on 60P₂O₅-10Al₂O₃-30ZnO (PAZ) glasses system that doped with varied rare-earth (RE) elements Yb₂O₃/Er₂O₃. The glass transition temperature, softening temperature and chemical durability were increased with RE-doping concentrations increasing, whereas thermal expansion coefficient was decreased. In the optical properties, the absorption and emission intensities also increase with RE-doping concentrations increasing, When Er₂O₃ and Yb₂O₃ concentrations are over than 3 mol% in the Er³⁺-doped PAZ system and Yb³⁺-doped concentration is over than 3 mol% for Er³⁺/Yb³⁺-codoped PAZ system, the emission intensity significantly decreases presumably due to concentration quenching, formation of the ions clustering, and OH⁻ groups in the glasses network. It is suggested that the maximum emission cross-section (σ_e) is 7.64 × 10^− 21 cm² at 1535 nm is observed for 3 mol% Er³⁺-doped PAZ glasses. Moreover, the maximum σ_e × full-width-at-half-maximum is 327.8 for 5 mol% Er³⁺-doped PAZ glasses.     

Spectral properties of PbO-P2O5 glasses

The optical absorption spectra of xPbO-(100 − x) P₂O₅ glasses where x = 5, 10, 15, 20, 25, and 30 is reported. The spectral absorption of these glasses was measured in the spectral range 300-900 nm at room temperature. Optical absorption spectra show that the absorption edge has a tail extending towards lower energies. The edge shifts nearly linearly towards higher energies with increasing PbO content. The degree of the edge shift was found to depend on the PbO content and is mostly related to the structural rearrangement and the relative concentrations of the glass basic units. The optical energy gap increases, from 2.55 to 3.05 eV by increasing PbO content from 5 to 30 mol%. The width of the localized states is decreased by increasing PbO content.     

Sodium tracer diffusion in glasses of the type (CaO·Al2O3)x(2 SiO2)1−x

Tracer diffusion coefficients of the radioactive isotope Na-22 were measured in glasses of the type (CaO·Al₂O₃)_x(2 SiO₂)_1−x to study the diffusion of sodium as a function of glass composition, x, temperature and initial water content. The diffusion of Na-22 in glasses diffusion-annealed in dry air can always be well described by a single tracer diffusion coefficient, but sometimes not in samples annealed in common air. It was found that the sodium tracer diffusion coefficient decreases by about six orders of magnitude when the glass composition x changes from 0 to 0.75 at 800 °C. The temperature dependence of the diffusion of sodium seems to decrease as the silica content increases. Variations of the initial water content in some of the glasses investigated did not very significantly influence the rate of the tracer diffusion of sodium.     

Dielectric analysis of tungsten-phosphoniobate 20A2O-30WO3 -10Nb2O5 -40P2O5 (A = Li, Na) glass-ceramics

New phosphate glasses of the quaternary system A₂O-Nb₂O₅-WO₃-P₂O₅, where X = Li and Na were prepared by the melt-quenching method. The introduction of WO₃ in the glass composition was based on the proposal of analysing the effect of the diminishing of the molar amount of the alkaline oxide and thus decreasing the molar ratio between network modifiers and network formers (M/F).In the present work we present the preparation of 20A₂O-30WO₃-10Nb₂O₅-40P₂O₅ (A = Li, Na) transparent glasses. These glasses were heat-treated in air, at 550 °C and 650 °C for 4 h. The structure of the obtained samples was studied by X-ray powder diffraction (XRD) and Raman spectroscopy and the morphology by scanning electron microscopy (SEM). The dc (σ_dc), ac (σ_ac) conductivity and dielectric spectroscopy measurements were performed in the function of the temperature and were related with the structural changes of the glass structures.     

Electrical conductivity and dielectric properties of Bi2O3-GeO2-PbO-MoO3 glasses

Glasses having compositions 40Bi₂O₃-20GeO₂-(40−x)PbO-xMoO₃ (where x = 3, 6, 9, 12 and 15 mol%) were prepared by normal melt quenching technique. The density (d) decreases gradually with the increase of the MoO₃ content in such glasses. This may be due to the lower molecular weight MoO₃ is substituted by a higher molecular weight PbO. The dc conductivity decreases while the activation energy increases with the increase of the MoO₃ content. The dc conductivity in the present glasses is electronic depends strongly upon the average distance, R, between the Mo ions. Analysis of the electrical properties has been made in the light of small polaron hopping model. The parameters obtained from the fits of the experimental data to this model are reasonable and consistent with glass composition. The conduction is attributed to non-adiabatic hopping of small polaron. Dielectric properties (constant ε, loss tan δ, ac conductivity σ_ac, over a range of frequency 0.12-100 kHz and temperature 325-650 K and frequency exponent s) of these glasses have been studied.     

Structure and non-linear optical performance of TeO2-Nb2O5-ZnO glasses

The non-linear optical performance and structure of TeO₂-Nb₂O₅-ZnO glasses was investigated as a function of ZnO content. The third-order non-linear optical susceptibility (χ⁽³⁾) as measured by a Degenerate Four Wave Mixing (DFWM) method, initially increased with increasing ZnO content to about 8.2 × 10⁻¹³ esu for a glass containing 2.5 wt% ZnO, and then decreased to 5.9 × 10⁻¹³ esu as the ZnO content increased to 10 wt%. There was no noticeable change as the ZnO content increased from 10 to 15 wt%. The non-linear optical response time, which caused electron cloud deformation, was from 450 to 500 fs. The structure of these glasses as analyzed by Raman spectroscopy and FT-IR spectra, was affected by the addition of ZnO up to 5 wt%, when, it is believed, the Zn²⁺ ions occupied the interstitial positions in the glass network by replacing the Nb⁵⁺ ions. The replaced Nb⁵⁺ ions occupied the network forming positions as the Te⁴⁺ ions. Increasing ZnO > 5 wt% did not have any further effect on the glass structure.     

Fabrication and properties of novel low-melting glasses in the ternary system ZnO-Sb2O3-P2O5

Glasses in the ternary system ZnO-Sb₂O₃-P₂O₅ were investigated as potential alternatives to lead based glasses for low temperature applications. The glass-forming region of ZnO-Sb₂O₃-P₂O₅ system has been determined. Structure and properties of the glasses with the composition (60 − x)ZnO-xSb₂O₃-40P₂O₅ were characterized by infrared spectra (IR), differential thermal analysis (DTA) and X-ray diffraction (XRD). The results of IR indicated the role of Sb³⁺ as participant in glass network structure, which was supported by the monotonic and remarkable increase of density (ρ) and molar volume (V_M) with increasing Sb₂O₃ content. Glass transition temperature (T_g) and thermal stability decreased, and coefficient of thermal expansion (α) increased with the substitution of Sb₂O₃ for ZnO in the range of 0-50 mol%. XRD pattern of the heat treated glass containing 30 mol% Sb₂O₃ indicated that the structure of antimony-phosphate becomes dominant. The improved water durability of these glasses is consistent with the replacement of easily hydrated phosphate chains by corrosion resistant P-O-Sb bonds. The glasses containing ?30 mol% Sb₂O₃ possess lower T_g (<400 °C) and better water durability, which could be alternatives to lead based glasses for practical applications with further composition improvement.     

The effect of PbF2 content on the microstructure and upconversion luminescence of Er-doped SiO2-PbF2-PbO glass ceramics

The Er³⁺ doped transparent oxyfluoride glass ceramics were obtained by appropriate heat treatment of the precursor glasses with composition (mol%) 50SiO₂-xPbF₂-(50 − x)PbO-0.5ErF₃. The microstructure and optical properties of the glasses and glass ceramics were determined by differential scanning calorimetry (DSC), X-ray diffraction (XRD), absorption spectra and luminescence spectra. The intensity of upconversion luminescence significantly increased in glass ceramics compared to that in precursor glass. The emission bands centered around 660 nm (⁴F_9/2 → ⁴I_15/2) and 410 nm (²H_9/2 → ⁴I_15/2) were simultaneously observed in glass ceramics but cannot be seen in the corresponding precursor glass. The influence of different PbF₂ content on the microstructure and upconversion luminescence of the samples was analyzed in detail. The results indicated that with the increase of PbF₂ content, the Ω₂ was almost the same and the ratios of red to green upconversion luminescence decreased in glass ceramics.     

Synthesis and physical properties of glasses in the Sb2O3-PbCl2-MoO3 system

Lead chloroantimonite glasses form stable binary glasses that may accommodate numerous oxides or halides as a third component. Molybdenum trioxide is a glass progenitor leading to molybdate glasses. Ternary glasses have been synthesized and studied in the Sb₂O₃-PbCl₂-MoO₃ system. Compositional limits of glass formation are reported and two series of glass samples have been prepared corresponding to the general formulas: (90 − x)Sb₂O₃-xPbCl₂-10MoO₃ and (90 − x)Sb₂O₃-xMoO₃-10PbCl₂. Glass transition temperature is close to 290 °C at high Sb₂O₃ content and decreases as antimony oxide is substituted by MoO₃ or PbCl₂. Position, width and intensity of crystallization peak suggest that devitrification rate is small in some composition ranges. The evolution of density, thermal expansion, refractive index and microhardness has been studied as a function of composition parameter x. Deviations from linearity are observed. They suggest structural changes in the case of the MoO₃/Sb₂O₃ substitution while it appears that molar volume increases linearly versus lead content in the other series of glasses. Refractive index is close to 2.04. Optical transmission ranges from 550 nm in the visible spectrum to 5.5 μm in the infrared. It is limited by extrinsic absorption bands arising from hydroxyls and silicon impurities. Young's, bulk and shear moduli have been measured for the two series of samples.     

New tungstate fluorophosphate glasses

A new class of tungstate fluorophosphate glasses was identified in the NaPO₃-BaF₂-WO₃ ternary system. The variation of several physical properties was determined with respect to chemical composition. Characteristic temperatures, density and refractive index increase as tungsten oxide content increases. The optical transmission range and specially the energy bandgap depend of the WO₃ amount. No crystallization could be observed for the most WO₃ concentrated vitreous samples (?20% molar). Color and optical properties of the glasses depend of the melting time because of the presence of reduced tungsten species like W⁵⁺ and W⁴⁺. In addition, photodarkening is observed in tungsten rich glass samples under UV laser illumination and this phenomenon can be reversible by heat treatment near the glass transition temperature.     

Influence of Y2O3 on structural and optical properties of SiO2-BaO-ZnO-xB2O3-(10−x) Y2O3 glasses and glass ceramics

SiO₂-BaO-ZnO-xB₂O₃-(10−x) Y₂O₃, (0 ≤ x ≤ 10) glasses are synthesized. The effect of Y₂O₃ on the structural and optical properties of glasses has been investigated using different characterization techniques. The results are discussed in light of non-bridging oxygens (NBO), optical basicity and heat-treatment of glasses. The band gap has been calculated for as cast and heat-treated glasses. The band gap energy is found to decrease with the increasing content of Y₂O₃ in the glasses and heat-treatment. The presence of the crystalline phase in the glass matrix showed remarkable effect on band gap which decreases to semiconducting range.     

The comparative structure, properties, and ionic conductivity of LiI + Li2S + GeS2 glasses doped with Ga2S3 and La2S3

The well known and characterized fast ion conducting (FIC) LiI + Li₂S + GeS₂ glass-forming system has been further optimized for higher ionic conductivity and improved thermal and chemical stability required for next generation solid electrolyte applications by doping with Ga₂S₃ and La₂S₃. These trivalent dopants are expected to eliminate terminal and non-bridging sulfur (NBS) anions thereby increasing the network connectivity while at the same time increasing the Li⁺ ion conductivity by creating lower basicity [(Ga or La)S_4/2]⁻ anion sites. Consistent with the finding that the glass-forming range for the Ga₂S₃ doped compositions is larger than that for the La₂S₃ compositions, the addition of Ga₂S₃ is found to eliminate NBS units to create bridging sulfur (BS) units that not only gives an improvement to the thermal stability, but also maintains and in some cases increases the ionic conductivity. The compositions with the highest Ga₂S₃ content showed the highest T_gs of ∼325 °C. The addition of La₂S₃ to the base glasses, by comparison, is found to create NBS by forming high coordination octahedral LaS₆³⁻ sites, but yet still improved the chemical stability of the glass in dry air and retained its high ionic conductivity and thermal stability. Significantly, at comparable concentrations of Li₂S and Ga₂S₃ or La₂S₃, the La₂S₃-doped glasses showed the higher conductivities. The addition of the LiI to the glass compositions not only improved the glass-forming ability of the compositions, but also increased the ionic conductivity glasses. LiI concentrations from 0 to 40 mol% improved the conductivities of the Ga₂S₃ glasses from ∼10⁻⁵ to ∼10⁻³ (Ω cm)⁻¹ and of the La₂S₃ glasses from ∼10⁻⁴ to ∼10⁻³ (Ω cm)⁻¹ at room temperature. A maximum conductivity of ∼10⁻³ (Ω cm)⁻¹ at room temperature was observed for all of the glasses and this value is comparable to some of the best Li ion conductors in a sulfide glass system. Yet these new compositions are markedly more thermally and chemically stable than most Li⁺ ion conducting sulfide glasses. LiI additions decreased the T_gs and T_cs of the glasses, but increased the stability towards crystallization (T_c − T_g).